A new Dynorace has just been released! The new Dynorace A2CTION power bench tester has been designed and developed to support the latest vehicles technology: the result is extraordinary, a 4WD braked dynamometer – also available in ACTIVE configuration – provided with single roller frame and rigid connection between front and rear axle (thanks to a driveshaft).

This platform has been conceived not only to brake the acceleration of the car (simulating load conditions/uphill roads) but also – when provided in ACTIVE configuration – to accelerate the rotation of the wheels (simulating downhill conditions and for hybrid/electric vehicles testing while – as example – recharging the batteries).

The structure of the new power bench tester supports two brakes (one for each axle) and an electric engine (optional) between the two axles. Top quality parts and components have been selected to ensure the maximum reliability and testing accuracy even in case of high performances vehicles.

An additional roller has been mounted on the front axle so to facilitate the vehicle positioning on the power bench tester. High inertia rollers (diameter 605 mm) have been produced with a knurling surface treatment which limits the risk of slip. Moreover, a new set of bearings improve their performances and durability.

A new state-of-the-art electronic management board allows faster data collecting, so to guarantee a very high precision in the testing operations.

MAIN FEATURES

SINGLE ROLLER developed to achieve greater inertia and supported by a high-resistance alloy steel shaft, with conical couplers to ensure a perfect alignment.

DIRECT MECHANICAL CONNECTION, to faithfully replicate the road working conditions. The front-rear connection is ‘excludable’, a peculiar feature of Dimsport Dynorace power bench testers.

AUTOMATIC WHEELBASE ADJUSTMENT achieved by inputting the vehicle wheelbase size in the management software, so to automatically set the exact position of the moving axle.

EDDY CURRENT BRAKE provided with a forced air duct to keep the load cell in a controlled temperature range.

SAFETY BRAKE to slow down the power bench and the vehicle in testing phase and to ensure maximum safety also in case of emergency.

POSITIONING ROLLERS to set the most suitable position (automatically determined by the software by inputting the tire size) and also to identify situations of slip between tire and roller.

33 KW ELECTRIC ENGINE (OPTIONAL) soon available to support realistic road simulation cycles and to replicate the inertial mass of the vehicle in testing also for homologous purposes.

Discover all Dynorace A2CTION features on their website!

The post Dynorace A2CTION appeared first on Checksumm: Chiptuning Forum.

Magikmotorsport have just releases a new complete standalone OBD solution for BMW & Mini Fxx series vehicles. This unique tool eliminates the need of the removal of the ECU from the vehicle as well as the execution of TPROT OFF in BSL before proceeding to work in OBD mode.

The new BMW Fxx OBD Flasher is available now at a special price of just 1900€. The package contains the BMW Fxx OBD interface and a USB key for the OBD interface.

For more information please visit: Magicmotorspot

Supported vehicle models:
BMW: F01, F02, F06, F07, F10, F11, F15, F16, F18, F25, F26, F30, F31, F32, F34, F36, F80, F85, F86 Mini: F55, F56, F57

Supported engine models:
BMW: N13, N20, B47, N47, N55, S55, N57, N63TU, S63TU (excludes only: B48 and B58)

Minimum requirements:
PC requirements:
MCU: Dual Core i3
RAM: 4GB
OS: MS Windows 7,8 or 10 x32/x64
Ports: 1 x USB2.0 port, 1 x RJ45 Ethernet port
Network: mandatory internet connection (the IP address of the PC must be assigned by the DHCP server)

Vehicle requirements:
Battery recharger required min. 50A

The post BMW Fxx OBD Flasher appeared first on Checksumm: Chiptuning Forum.

Swiftec software is a powerful editing tool created by VCPower Team. This software allow the end user to get the maximum performance out of modern electronic controlled engines such as cars, truck, bikes, boats, any engine that are controlled via a ECU. Since its release back in 2008, the company behind Swiftec didn’t stop developing it!
And now there is a new version (Swiftec 1.9.4.9) with new unique solutions and wider coverage for previous ones!

TVA Removal module
Support for Dacia with Bosch EDC17_C42 has been added!
*IMPORTANT* Actuator plug must be disconnected!
Support for Nissan with Bosch EDC17_C42 has been added!
*IMPORTANT* Actuator plug must be disconnected!
Support for Renault with Bosch EDC17_C42 has been added!
*IMPORTANT* Actuator plug must be disconnected!
Support for Volvo with Bosch EDC16C34 has been added!
*IMPORTANT* Actuator plug must be disconnected!
More variations of Mercedes with Bosch EDC17_C42 has been added!

Torque Monitoring Disable module
Support for Mercedes with Bosch MED17.7.2 has been added!
Support for Nissan with Bosch EDC17_C84 has been added!
Support for Renault with Bosch EDC17_C84 has been added!
Support for Toyota with Bosch EDC17_C73 has been added!
More variations of Alfa Romeo with Bosch EDC17C69 has been added!
More variations of Fiat with Bosch EDC17C69 has been added!

Flaps / Swirl Removal module
Support for Mercedes with Bosch EDC17C66 has been added!
*IMPORTANT* Actuator plug must be disconnected!
More variations of BMW with Bosch EDC17_CP45 has been added!
More variations of Honda with Bosch EDC16C31 has been added!

StartStop Disable module
Support for Mazda with Denso has been added!
Support for VAG with Bosch EDC17_CP54 has been added!

DTC Removal module
Support for Case with Bosch EDC17C49_C has been added!
Support for Renault with Bosch ME17.9.20 has been added!
More variations of BMW with Bosch EDC17_CP09 has been added!
More variations of Case with Bosch EDC17CV41 has been added!
More variations of Fiat with Bosch EDC16C39 has been added!
More variations of Fiat with Bosch EDC17_C49 has been added!
More variations of Ford with Bosch EDC17_CP05 has been added!
More variations of Ford with Siemens SID206 has been added!
More variations of Ford with Siemens SID209 has been added!
More variations of Hyundai with Bosch EDC16C39 has been added!
More variations of Hyundai with Bosch EDC17_C57 has been added!
More variations of Jeep with Bosch EDC17_CP27 has been added!
More variations of Mercedes with Bosch EDC16CP31 has been added!
More variations of Mercedes with Bosch EDC17C66 has been added!
More variations of Mercedes with Delphi CRD3 has been added!
More variations of Mitsubishi with Bosch EDC16C31 has been added!
More variations of Mitsubishi with Denso has been added!
More variations of Nissan with Bosch EDC17_C84 has been added!
More variations of Nissan with Siemens SID305 has been added!
More variations of Opel with Bosch EDC17_C11 has been added!
More variations of Opel with Bosch EDC17_C84 has been added!
More variations of Renault with Bosch EDC16C3 has been added!
More variations of Renault with Bosch EDC17_C42 has been added!
More variations of Renault with Bosch EDC17_C84 has been added!
More variations of Renault with Siemens SID307 has been added!
More variations of VAG with Bosch EDC16CP34 has been added!
More variations of VAG with Bosch EDC16U34 has been added!
More variations of VAG with Bosch EDC17_CP14 has been added!
More variations of VAG with Bosch EDC17C64 has been added!

ADBlue Removal module
Support for Kamaz with Cummins CM2150E has been added!
*IMPORTANT* SCR AND NOX FUSES / RELAYS, ADBLUE UNIT AND NOX SENSORS have be disconnected!
Support for Maz with Temic PLD has been added!
*IMPORTANT* ADBLUE UNIT have be disconnected!
Support for Mercedes with Delphi CRD3.XA has been added!
*IMPORTANT* ADBLUE UNIT have be disconnected!
Support for Mitsubishi with Bosch EDC16C31 has been added!
*IMPORTANT* SCR AND PUMP have be disconnected!
Support for VAG with Bosch EDC17C74 has been added!
*IMPORTANT* NOX SENSORS can be disconnected!
New solution for Deutz with Bosch EDC17CV52 has been introduced!
*IMPORTANT* ADBLUE ECU / PUMP and TANK have be disconnected!
New solution for Fendt with Bosch EDC17CV56 has been introduced!
*IMPORTANT* ADBLUE ECU / PUMP have be disconnected!
New solution for Land Rover with Bosch EDC17CP55 has been introduced!
*IMPORTANT* NOX SENSORS can be disconnected!
New solution for Land Rover with Bosch MEDC17.9 has been introduced!
*IMPORTANT* NOX SENSORS can be disconnected!
New solution for Massey Ferguson with Bosch EDC17CV54 has been introduced!
*IMPORTANT* ADBLUE ECU / PUMP have be disconnected!
New solution for Mercedes with Bosch EDC17CP10 has been introduced!
*IMPORTANT* DASH CODING is not required anymore!
More variations of BMW with Bosch EDC17_C79 has been added!
More variations of Fendt with Bosch EDC17CV52 has been added!
More variations of Jeep with Bosch EDC17_C79 has been added!
More variations of Mercedec with Bosch EDC17C66 has been added!
More variations of Mercedec Truck with Temic ACM has been added!

DPF Removal 2.0 module
Support for Citroen with Delphi DCM6.2 has been added!
Support for Ford with Delphi DCM6.1 has been added!
Support for International with Bosch EDC17CV42 has been added!
*IMPORTANT* DPF Pressure and EGT sensors have be disconnected!
Support for Tigercat with Cummins CM2250 has been added!
*IMPORTANT* DPF Pressure and EGT sensors have be disconnected!
Support for Mercedes with Siemens SID307 has been added!
Support for Peugeot with Delphi DCM6.2 has been added!
New solution for Mercedes with Bosch EDC17C66 has been introduced!
*IMPORTANT* DPF Pressure and EGT sensors have be disconnected!
More variations of Alfa Romeo with Bosch EDC17C49 has been added!
More variations of Alfa Romeo with Marelli MJ8x has been added!
More variations of Citroen with Siemens SID208 has been added!
More variations of Ford with Delphi MPC555 has been added!
More variations of Ford with Siemens SID807 has been added!
More variations of Isuzu with Transtorn has been added!
More variations of Iveco with Bosch EDC17CV41 has been added!
More variations of Land Rover with Bosch EDC17CP55 has been added!
More variations of Mercedes with Delphi CRD3 has been added!
More variations of Nissan with Delphi DCM3.4 has been added!
More variations of Opel with Bosch EDC17_C18 has been added!
More variations of Opel with Bosch EDC16C9 has been added!
More variations of Opel with Bosch EDC17_C19 has been added!
More variations of Opel with Bosch EDC17_C59 has been added!
More variations of Peugeot with Siemens SID208 has been added!
More variations of Renault with Delphi DCM3.4 has been added!
More variations of Toyota with Bosch EDC17_C73 has been added!
More variations of VAG with Bosch EDC17_CP14 has been added!
More variations of VAG with Bosch EDC17_CP44 has been added!
More variations of Volvo with Siemens SID803 has been added!

EGR Removal Module
Support for Citroen with Siemens SID208 has been added!
Support for Hyundai with Delphi DCM3.7 has been added!
Support for Kia with Delphi DCM3.7 has been added!
Support for Land Rover with Bosch EDC17CP55 has been added!
Support for Land Rover with Bosch MEDC17_9 has been added!
Support for Peugeout with Siemens SID208 has been added!
Support for Tata with Delphi DCM3.7 has been added!
Support for VAG with Bosch EDC17_CP54 has been added!
*IMPORTANT* EGR ACTUATOR have be disconnected!
More variations of Renault with Bosch EDC16C3 has been added!
New solution for Ford with Bosch EDC16C3 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
New solution for Ford with Bosch EDC16C7 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
New solution for Land Rover with Bosch EDC17_CP42 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
New solution for Mercedes with Delphi CRD2 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
New solution for Opel with Delco MT35 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
New solution for Saab with Bosch EDC16C9 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
New solution for Volvo with Bosch EDC17_CP22 has been introduced!
*IMPORTANT* EGR ACTUATOR have be disconnected!
More variations of Opel with Marelli MJ6D has been added!

Speed Limiter Removal module
Support for BMW with Siemens MSD85 has been added!
Support for Fiat with Bosch EDC16C8 has been added!
Support for Ford with Siemens SID211 has been added!
Support for Mercedes with Bosch EDC16CP36 has been added!
Support for Opel with Bosch EDC16C39 has been added!
More variations of BMW with Siemens MSD80 has been added!
More variations of Fiat with EDC16C39 has been added!
More variations of Mercedes with Bosch EDC15C6 has been added!
More variations of Toyota with Denso has been added!
More variations of VAG with Bosch MED17.5 has been added!
More variations of VAG with Siemens SIMOS 10 has been added!

Lambda/O2 Removal module
Support for Chevrolet with Siemens SIMTEC76 has been added!
Support for Ford with Visteon M799G has been added!
Support for Mazda with Visteon M799G has been added!
Support for Mini with Siemens EMS has been added!
Support for VAG with Bosch ME17.5.26 has been added!
More variations of BMW with Siemens MS43 has been added!
More variations of BMW with Siemens MSD8x has been added!
More variations of BMW with Siemens MSS52 has been added!
More variations of BMW with Siemens MSS54 has been added!
More variations of Hyundai with Bosch ME17.9.11 has been added!
More variations of Kia with Bosch ME17.9.11 has been added!
More variations of Opel with Siemens SIMTEC76 has been added!
More variations of VAG with Bosch ME7.1.1 has been added!
More variations of VAG with Bosch ME7.9.10 has been added!

Automatical Map Recognition Module
Support for VAG with Siemens SIMOS 18 (BETA) has been added!
More variations of VAG with Bosch MED17.5 has been added!

ECU Information Detection Module
Support for VAG with Siemens SIMOS 12 and SIMOS 18 has been added!

VAS Import module
Support for Bosch EDC17C74 has been added!
Conversion speed for newest models of ECUs has been optimized!

The post New Swiftec features appeared first on Checksumm: Chiptuning Forum.

Dimsport’s experience shows that every engine, every setup, every rider has a “peculiar” story to tell.

This is true also for every new applications being developed which is ultimately determined by a new and exciting challenge. It was no different when the new Suzuki GSXR 1000 rolled into Dimsport Rapid Bike R&D Dept, the mission was clear since the very beginning: “the beast” could be improved only by smoothing out its wild nature … today they are extremely satisfied since without any doubt we fully succeeded with reaching this goal!

At lower TPS openings the engine response is much more predictable and bike’s handling is definitely more friendly especially in regards of drive-by-wire’s side-effects; power gain is consistent and helps to push strongly the bike out from the curves while securing additional horsepower even in case of a vehicle in stock configuration…

… but who is going to leave “the beast” in his cage ?!

The post Suzuki GSXR1000 with Rapid Bike technology appeared first on Checksumm: Chiptuning Forum.

Vtechdyno EVO – a new line of modular, expandable chassis dynamometers – has been shown at Automechanika Frankfurt. The basis 2WD model (VT-2) starts from 14.900 €.

Modular dynamometer means that there is no need to buy AWD dyno at once. You can have the front module, without electromagnetic brakes, and install brakes, AWD extension with synchronization and additional sensors later. Thanks to fully modular design, everything is expandable. There is no need of investing more money for full AWD to avoid being stuck with 2WD. Now 2WD → AWD expansion is easy. AWD is fully mechanically synchronized. Apart from typical sensors (AFR, EGT, Boost etc), the control software includes OBD2/CAN input of data.

The VT2/VT4 chassis dynamometers series have been present on the European market for almost 20 years. The first rolling road was created and installed in 1999 and since the very beginning they featured an exceptional accuracy of measurement and reliability. During the following years the chassis dynos (rolling roads) have been constantly developed and improved by R&D department, significantly widening the product range. Today variants of our dynamometers include modular one-axle dynamometer and 4WD chassis dynamometer for 4×4 vehicles. Multiple models, configurations and options of chassis dynamometer product line are available.

Vtechdyno dynamometers are available in both inertial and braked versions. Additionally, in the 4×4 version a novelty system of mechanical synchronisation of front and rear axles is used, which gives the possibility for measuring the most modern cars, equipped with active traction control systems. Supplementary to this wide offer are dynamometers for motorcycles and quads. All models can be installed in pit or on surface.

More information here: http://vtechdyno.eu/chassis-dynamometer-gallery.html

If you want to see Vtechdyno in action, you can find nearest to you at http://dynosmap.com

The post modular dynamometers from Vtechdyno appeared first on Checksumm: Chiptuning Forum.

OLS Projections is a company that supply access and sells membership to a private online database of WinOLS OLS Projects or mappacks. Depending on the type of membership it allows you to access the database where you access OLS files for winols (mappacks) and A2L/Damos files.

The membership is a one off fee and the database is updated monthly. After 12 months, there is a small subscription charge to stay on service.

The database includes files for normal cars and supercars. OLS Projections also offer custom mappacks for bikes/boats/jetskis however these will be separate orders and not on server base.

Please note that OLS Projections are a long term loyal customer of EVC and have a genuine licence of EVC Winols. They do not support cracked versions of Winols and will not supply any type of projects for these customers.

OLS Projections will also add EVC Winols training soon which will be offline and online using a secured server and webinar system.

There are different types of membership: Basic membership is Gold that allows you download multiple mappacks and A2L files from their server. Diamond Membership is same as Gold but they added in supercars mappacks. VIP Platinum membership same as Gold and Diamond but for 12 months you can have custom projects / mappacks made by OLS Projections using your original file and its unlimited. They also offer a service where we can make you a tuning mappack based on your needs. They do not sell tuned files.

For more information and prices please visit http://www.olsprojections.com
Or contact olsprojections@outlook.com

The post OLS Projections appeared first on Checksumm: Chiptuning Forum.

Cobra Sport’s performance exhaust for the VW Golf Mk7 ‘R’ has been enjoying universal acclaim since it was launched last year. The performance enhancing large bore stainless steel pipework, the choice of resonated or non-resonated centre sections and the option of having a valved or non-valved exhaust have all proved extremely popular with customers and the press. Now Cobra Sports race partner, AmD Tuning, has developed a remap that has been specially developed to work hand-in-hand with the new exhaust system.

The AmD software remap works with the new-found increased efficiency of the exhaust and develops upon it. The combination creates more power than just the sum of the gains that would be achieved by the exhaust and software added together.

Because the AmD remap has been designed specifically to work with the Cobra Sport exhaust you can be sure that everything will work with maximum efficiency and without any fault codes being triggered in error.

AmD Tuning also offer FREE FITTING on all Cobra Sport Exhausts – or, if you prefer to buy by mail order and fit it yourself, AmD will offer 10% off and FREE DELIVERY – which can represent a significant saving on a full system. Furthermore, if you buy an AmD Tuning performance remap at the same time as a Cobra Sport Exhaust you can have the remap at HALF the usual retail price!

Contact AmD Tuning for further details on 01708 861827 or visit www.amdtuning.com

The post AmD Tuning Package for VW Golf R appeared first on Checksumm: Chiptuning Forum.

Respected supercar tuner Litchfield has announced the development of its latest range of version 6 engine and gearbox map upgrades for the Nissan R35 GT-R. Having worked closely with long standing technical partner EcuTek, Litchfield has created a range of innovative revisions to include new hardware which will transform how owners interact with their GT-Rs. This latest software calibration significantly moves the game on in terms of performance and functionality.

Having worked together for many years, Litchfield has long been a Beta tester of EcuTek’s latest technology. Throughout the development process of the new ‘ECU Connect’ package the two firms shared R&D data in order to create an exceptionally complete package that offers a consumer interface not normally available with this kind of tuning.

The ECU Connect hardware is simply a Bluetooth dongle that seamlessly connects to Apple iPhone and iPad devices (Android to follow) when plugged into the standard OBD port. Once installed the OBD plug can be clicked into place in the factory port with the dongle still attached, leaving a neat and permanent connection to the ECU.

ECU Connect provides all the current ProEcu GTR features such as clutch learning, service tool, code reading and new extended data logging, but also offers drivers and tuners access to much more data. Drivers can use the app to perform convenient data logging with just a tap of the screen and easily email the results to any interested parties. Data logging is also extended to log both the engine ECU and gearbox TCM at the same time. Perfect for fine tuning and faster fault finding.

The most impressive feature of ECU Connect – and the core basis for Litchfield’s new Version 6 maps – is the ability to adjust each Customs Maps live within the app. Owners are now able to tailor their setup instantly to suit road/track conditions on the fly, using simple on/off toggles and on-screen sliding adjusters to change special map features.

Litchfield will be offering these live adjustments to control any aspect of its mapping. Whether that’s a new and improved traction control, the introduction of boost levels off the line, or even how loud you would like the volume of your over-run pops & bangs! The company is also working on some really clever new features to help those customers that like to test their GTR on track or drag strip, too!

Along with the hardware integration, Litchfield has also taken the opportunity to apply its latest updates and Ring-tested results to its Version 6 maps. These see an overall improvement in performance, throttle response and fuel consumption across the board, making the upgrade hugely worthwhile – and more than just a series of new features.

Testing has been completed on Litchfield’s own GTR test cars (MY10, MY11 and MY17) on both road, dyno and circuit to ensure everything is thoroughly proven and optimised. Naturally, as new upgrades and features are available, these will be added into the package as well as being made available retrospectively to existing customers.

A more detailed list of key features will be released on the Litchfield website in the coming weeks as full testing is completed. The ECU Connect hardware is due to launch at the end of November in limited numbers with more units due later in the year. Pricing will be in line with all of Litchfield’s other mapping options.

For more information on this exciting new innovation, please click to www.litchfieldmotors.com

The post Litchfield Announces New ‘ECU Connect’ Engine and Gearbox ECU Options For GT-R appeared first on Checksumm: Chiptuning Forum.

After several years of research and development BSR Tuning announce some unique Tuning for Volvos new generation VEA diesel engines. The new tuning kits are different from anything else on the market and promise a hard to beat power increase.

Since Volvo is one of the brands which has been a big part of the foundation of the BSR success story, the pressure and demand to deliver tuning for Volvos VEA engines has been huge. Since 2014, in BSR’s lab in the deep Swedish forests, their engineers have been researching to develop the potential in the new generation powertrain. The result is an extraordinary documented power increase which surpasses what is available on the market. The VEA engines, in combination with Volvos solid and often oversized other parts, are particularly well designed to handle the power increase that has been developed. As always, all BSR tuning kits are custom made for the specific engine option, power train and chassis to not challenge anything in the build or get an unsustainable wear due to the increased power output.

The extraordinary power increase has led to that a big part of the projects focus has been to give the cars the right driving experience during all possible scenarios and to adjust the tuning to avoid wear. This, in combination with correct basic conditions in the engine, makes the cars behaviour stable during all circumstances and intervals when tuned. The D2, D3 and D4 engines are the first to be released. D5, as well as the petrol engines, will be announced later on. When the software has been loaded into the car by BSR the customer can shift the cars setup from original to tuned when and how often they wish to using the handheld PPC unit, all by themselves. The PPC unit is easily connected to the cars diagnostics socket.

”The VEA seemed promising from the start but to achieve such good and thorough results was more than we expected. It’s been a great challenge for our team to get the right interaction between all parameters and details. However, in true BSR spirit, we have managed to create something truly unique. It feels like we have released the soul of the engine, what it was built for, the inner beast.” – Stefan Olsson, CEO – BSR Svenska AB

Tuning kits:
D2
BSR stage 1:
+ 57 hp, + 83 nm

D3
BSR stage 1:
+54 hp, +103 nm

D4
BSR stage 1:
+47 hp, +92 nm

BSR stage 1+:
+67 hp, +107nm

BSR stage 3:
+75 hp, +107nm

The post Tuning for Volvos appeared first on Checksumm: Chiptuning Forum.

It is now official: Dimsport presence in the USA has been improved thanks to the opening of DIMSPORT NORTH AMERICA, important new branch established to reinforce our presence in the global tuning market.

The new company is situated in Ohio, a strategic choice to better serve USA and Canada, key markets in which their products have long since been appreciated by professionals and end-users for a wide range of applications.

Dimsport North America joins the “sisters” companies already operating in Spain, Turkey and Brazil in the support of the activities promoted by the head offices in Italy (in Serralunga di Crea and Scandicci).

Dimsport’s Board of Directors declares, “If on the one hand the launch of Dimsport North America reconfirms the globalization process of our brand, it must be clear that our satisfaction is not just the new flag on the globe: the presence of diligent referents in the United States allows us to serve the growing interest in electronic tuning. Optimization of the engine performance, improvement of the fuel economy, enhancement of the driving pleasure: now Dimsport has “that extra oomph” that makes it able to better deal with a demanding overseas clientele”.

For more information, please visit: www.dimsport.it

The post DIMSPORT North America appeared first on Checksumm: Chiptuning Forum.