Continuum

New FSRP Contributor

2007-06-04T20:46:00.000-07:00

ASIT's Food Service Resource Pages site been rather neglected over the winter, but that's changing...

We have a new user, Carl Muth, who as a writer, will be contributing to the site's content. Carl hails from Atlanta, Georgia, where he runs his company, FoodService Resource Associates, LLC. (...hmm, sounds familiar...) He's actually put together a rather extensive website catering to end-users and potential operators.

We look forward to collaborating with Carl, and we'll keep you up-to-date, or stop by the What's New page.

Daylight Savings Time Update

2007-03-05T22:33:00.000-08:00

I'm sure you all know about the new Daylight Savings Time change this weekend. But, you may not realize that your (Windows) computer system will not automatically adjust your system clock like it has in the past (since this is relatively recent legislation). However, Microsoft has a nice Daylight Saving Time Update Guide [http://support.microsoft.com/gp/cp_dst] to walk you through the update process.

Most of you will want to select "Home user" to start out, as the other selections assume you have an "IT Department" and the subsequent pages aren't very helpful. Firefox users will be prompted to install a Plug-In (I think IE7 users will too), but it's not big [±800kb] and won't interrupt the update process.

Goog luck to all, and see you on the other side!

Change of Venue

2006-11-13T12:28:00.000-08:00

Not sure if you noticed, but the ASIT web site, blog, and email all went down for a few days. This was because I was beguiled by Google's "Apps for your Domain" and decided to switch-over ASIT's email to Gmail (I'm a big fan). Unfortunately, once the new DNS settings kicked-in, mail was fine, but the site and blog went "bye-bye."

Well, as it turns out, it was an all or nothing situation; I would have to switch everything (website & blog, in addition to email) to Google if I wanted to keep Gmail. Since I've been paying Earthlink $25/mo. for hosting, and the Google services are free, it only took talking myself into re-building the two sites and all their content.

It was a lot of copying & pasting, but everything is now residing on Google's servers. I had to give-up the customized look of the site for Google's templates; I'm hoping there will be an option in the future for custom templates, but for now, the site is passable. And I have to admit, using the Google Pages interface is a lot easier that coding everything in HTML.

So we're back up and running, although I still have some site pages and blog posts to take care of (for example, the Gallery needs to be reconstructed). Of course, I'll keep you up-to-date on the progress here.

More Updates

2006-11-01T21:24:00.000-08:00

There were a couple minor typos on the site that were bugging me, so I've updated a few of the pages, as well as adding a site index. The Clients page has also been updated, with project lists for LGA and BRD.

I hope to have some corresponding gallery pages added soon, too.

We're Back

2006-10-15T23:06:00.000-07:00

One month and it's been very quiet here and at the website. Business is heavy at the moment, plus I had a business trip in the middle of it all. More on that soon.

Although, the good thing about being away for a while, is I've reviewed the site's pages with fresh eyes, allowing me to see the little things that needed fixing. So that's been done, with a few additions in textual content. More will come... soon.

More Site Updates

2006-09-15T18:28:00.000-07:00

A Clients page has been added to the site, listed in architectural and food service categories. Links to project lists will be forthcoming.

Also added some additional listings to some of the Links pages.

Creating A Wall Niche [ADT]

2006-09-14T20:50:00.000-07:00

NOTE: This post was moved to Back to the Drafting Board [drafting.aspaceintime.com] Future tips & how-to articles will be found there.

This post is the first of an ongoing series of tips and how-to articles for AutoCAD and Architectural Desktop. If you would like to make a request, or have a question about any of these articles, post a comment here or send an email to tips(at)aspaceintime.com.

This tip was originally in response to a posting in the AUGI forums by Marv Muston of Orlando, FL. I ran across a post in which Marv asked how to make a niche in a wall entity in Architectural Desktop (ADT). In other words, how does one make an recess in a wall, with no "thru-the-wall penetration," as he put it. He was trying to make a shelf within the wall, which is a common architectural element, so this is a good question. After posting my suggestion of using a "chase" symbol, I got the feeling from the forums that these symbols were fairly unknown, so I thought I'd expand this tip to an actual "how-to," showing step-by-step how to accomplish this.

Well, like so many other things in AutoCAD, there are many different ways you could make a niche. The most precise, yet most complicated way is to use body modifiers [command: WALLBODY] to attach mass elements to the wall, then specify either a subtractive or additive state. This truly is the most precise way to get the wall entity to look exactly the way you want, but if you are dealing with a wall style with multiple components, this can get to be a very tedious maneuver, as each component needs it's own additive or subtractive element attached to it. One major disadvantage of this is if you change the wall length, you (probably) will also have to update the modifiers manually; the other disadvantage of this is you usually need to customize the display properties of the wall as well, to get it to look the way you want in the plan view.

So, a nice and easy alternative is to use a "chase," which is a multi-view block, with some extra properties, namely it's very own body modifier, built right in! More on that in a minute... You can find six different styles of chases in the Design Center, in their own folder (called "chases"), under the "Documentation" section of the AEC Content tab.

The only difference between them is the plan view, which you can see in the preview, as well as the icons. There is no elevation or 3D element to these, so you will only see the 2D symbol in the plan view. [BTW: the path shown at the bottom of the image (above) will be different on your own system, as I have mine mapped through a network drive "S:"] Now that you know where to find them, all you have to do is click and drag them into your drawing. Lets go through the steps...

Here I have a standard wall in which we're going to make a niche. The top shows the plan view, and the bottom shows both faces, or sides, of the wall in hidden views. We pick a chase from the Design Center and drag it into the drawing. You are asked to specify an insertion point.

I generally pick somewhere that places the symbol over the wall. When we click, the following dialog box appears:

Here you see those special properties I was talking about. In addition to the standard settings of location (Insertion Point), size (Scale) and angle (Rotation), you are given options for a Description (in this case "Electrical Panel" which is one of the things I use chases for), setting a Label (such as an item number callout), and setting an Interference condition. This last item is the most important for what we're trying to do.

Click the Select Objects button, then click on the wall you're placing the chase into. The dialog box will come back and you'll now have the option to choose Additive, Subtractive or Ignore.

We want to set it to Subtractive; this will make a hole in the wall. If you know the dimensions of your niche and where you want to locate it within the wall, this would be a good time to change the other settings, but for now, click Ok, so we can see how the chase works.

Now we have a chase symbol in our wall. Notice in the plan view that the wall gets "cut" where the symbol is; plus, in the 3D views, we have a opening in the wall.

I know, you're saying, "I could have used an opening to do this," and you are correct; but, we're not done yet. We need to change the size and location of the chase; right now it's a 2'-0" wide, 1'-0" deep by 8'-0" high chase sitting on the floor (zero 'Z' coordinate). What we want to do is make it narrower than the wall and somewhere up in the wall. First, select the chase and open the Properties dialog (or just go to the Properties Palette).

Since the wall in this case is 4 1/2" wide, we want to change the Scale to have an 'Y' value less than that, say 4". Additionally, since this is an "Electrical Panel," we want to change the 'X' and 'Z' values to something more realistic, like 18" wide and 36" high. To get it off the floor, we then need to change the Elevation value, to like 4'-0". The properties should now look like this:

...and the drawing should now look like this:

Okay, so my aim wasn't real good. But you'll notice in the plan view that the symbol still cuts the wall, but now the "below cut plane" part of the wall is also showing (magenta, in this case). Plus, in the 3D views, there's no longer a hole, but a recess on only one side of the wall. We're almost there. Now it's just a matter of moving the chase symbol into place, and that's as easy as using the move command or using the symbol's node, whatever your preference.

That's better. Now we have a well placed niche in one side of the wall. Just be careful when moving the chase symbol using object snaps, as you could force the elevation back to 0" by snapping to the wall in the plan view. If you would like to play with this example, you can download the drawing file by clicking the box.net button below.

Let me know if you found this tip helpful by posting a comment. I hope to continue posting tips, but I'd like to know (1) I have an audience and (2) what you might be interested in me showing you.

AutoCAD & ADT Tips

2006-09-14T20:25:00.000-07:00

I'm adding an "CADD Tips" section to the blog. I will be posting various how-to articles for AutoCAD in general, and more specifically Architectural Desktop.

Since I am a member of the Autodesk User Group International, or AUGI, I have had the opportunity to answer various questions posted to forums. I try to keep my posts succinct, so it doesn't always allow for elaboration on a technique. But by using this blog, I will be allowed to make more detailed explanations, as well as including screen shots. I also want to have links to example drawings that anyone can download and play with.

If you have anything you'd like to know about, I'd be happy to produce a post on the subject (assuming of course it's not beyond my experience). Just post a comment here, or send an email to tips(at)aspaceintime.com.

ADDENDUM: Tips will now be posted on the Back to the Drafting Board site, under Tips & How-To.

Updated Pages

2006-09-10T22:39:00.000-07:00

More updates to site:

Added a "Services" page.
Added a new links page for food service equipment (by manufacturer name).
Some minor edits to the Food Service section main page and the links page.
Added some more CTB files to the SUPPORT page.

Contact me or leave comments here is you find any broken links, or would like your company added to the links section.

In addition to the site updates, the blog has some additions as well. Comments and trackback capabilities are back, thanks to HaloScan. Also, FeedBurner now handles the RSS feed, so you can now subcribe with your preferred feed reader. You can even add the feed to your personalized Google home page! (all this is under the "Syndicates" section at right)

ASIT Site Launched!

2006-09-04T22:58:00.000-07:00

The A Space In Time web site has been officially launched. There's still a lot to be done and added, but for now, the basic pages of the site have been posted. More will be added over the coming weeks, so check back here often for the latest!

New Blog Theme

2006-09-04T17:47:00.000-07:00

In case you didn't notice, the blog has a new look. I've gotten input from some saying the theme was a little dark, specially on LCD monitors, which I agree. So until I can take the time to customize a theme to match the ASIT web site page style, we now have a new theme, as well as a different way of posting.

I'm sorry to say Blogger is no longer servicing this blog. Don't get me wrong, there's nothing wrong with Blogger (I'm a big Google fan), it's just (1) I'm a more "hands-on" user and found a very nice program called Thingamablog, and (2) they need to iron-out the "classic" vs. "beta" problems over there.

As always, feel free to leave comments...

Picks & Links

2006-09-03T16:43:00.000-07:00

I've posted some more pages and updates to the site; most notably the Gallery and Links sections. There's still a lot more to add, but this will be an ongoing process.

The Gallery has one full project up. (see the "featured" projects in the right side bar) I'll try to have all the "featured" boxes filled before launch. I have to apologize in advance to all the Internet Explorer users out there, as for some strange reason, the Gallery pages don't always render correctly in IE (Thanks, Bill...) Outside of the fact that the background is supposed to stay fixed (not scroll-up with the page) and a few other minor things that don't really detract from the site, sometimes its more blatant, like the footer floating behind the main body. But then, that's why (in my humble opinion) you should be using another browser, like FireFox or Opera. But I digress...

The Links section currently has a main page and a page for CADD related links. I'm still putting together the AEC and Food Service links pages; the FS pages are the longest...I didn't realize just how many sites I've accumulated in my bookmarks (a.k.a. "favorites") over the years! I'm going to have to post those various pages in installments.

Anyway, peruse at will and let me know if there's anything I need to fix, or if there's something you'd like to see... all input is welcome... and encouraged!

Plus, before I forget, I want to give a big Thank You! to Lisa and "my friend" for sniffing-out the typos on the site. Keep up the good work!

Basic Pages Uploaded

2006-08-28T16:37:00.000-07:00

I've posted the pages for ASIT in general, like the "About", "Contact" and "Credits" pages (...so now my "hint" in the previous post is no longer entirely true).

The rest of the site may have to wait 'til later (work is picking up again), but taking my friend's advice to heart, I wanted to get these basic pages up for feedback on the layout (and help with the "blurbage.")

Now I have to send out a few invites...

...Round One begins!

Front Page Updated

2006-08-28T15:33:00.000-07:00

The new front page is posted (...mainly to test the countdown clock, which is working). Unfortunately, this aslo means I'm commited to getting the site going by Labor Day Weekend!

I worked on the majority of the pages this last weekend, and everything seems to work. Now I have to "flesh-out" the text. Most of it is just place holders, but enough that I could go "live" so that that I could invite those to test it. I be sending out notices soon. A good friend keeps saying, "keep it simple," and I just may have to do that, and leave all the rest of the site for later. We'll see how much I get accomplished...

...back to work.

[hint: there is a hidden link somewhere on the page... you could fish around for it and see your cursor change, but the page it links to isn't complete and none of the links go anywhere, except back here.]

Welcome!

2006-08-24T16:31:00.000-07:00

This is the brand new web log for A Space In Time. Here you will find the latest happenings, starting with the construction, testing, and posting of the new (and long awaited) web site. Feel free to comment on anything you see here or on the main site, or you can email the Webmaster directly.

Thanks for stopping by!