Dlink Basic Configuration & Setup

DXS/DGS-3300

2010-05-12T21:23:00.003+07:00

DWS-1008

2010-05-12T21:23:00.001+07:00

DWM-652

2010-05-12T21:22:00.005+07:00

>>> DWM-652 is not supported in Win 7

This device has been discontinued and there will be no more further maintanance.
So Windows 7 will not be supported.

-------------------------------------------------

DWM-151

2010-05-12T21:22:00.003+07:00

DWL-P200

2010-05-12T21:22:00.001+07:00

DWL-G700AP

2010-05-12T21:21:00.003+07:00

>>> DWL-G700AP How do I configure repeater mode on DWL-G700AP?

Step 1 Connect your DWL-G700AP using the UTP ( network ) cable.

Step 2 Launch your web browser, enter the IP address of DWL-G700AP (default is 192.168.0.50) and press Enter.

Step 3 Enter the username (“admin” by default) and your password (blank by default). Click OK to enter the web-based configuration for the device.

Step 4 You will see a DWL-G700AP configuration page shown as below
A) Click on Home.
B) Click on Wireless
C) Choose Repeater under Mode.
D) Click on Site Survey to search for the Access Point, which you want to connect to and repeat the signal.

Step 5 Select the AP which you want to connect to. Click on Connect button at the bottom of this small window.

Step 6 Please note that Repeater’s SSID, Channel and wireless security must be the same with AP1 (Access Point or Wireless Router).

Step 7 Click on Apply to complete the setup.

-------------------------------------------------
>>> DWL-G700AP How to set Access point (WEP)?

Step 1 Connect the DWL-2100AP to your PC using an Ethernet cable.

Step 2 Your computer will need to be in the same IP address range as the DWL-2100AP for configuration. The default IP address is 192.168.0.50.

Step 3 Open a web browser and enter in the IP address of the access point (192.168.0.50). The username is admin (all lower case) and the password is blank (nothing).

Step 4 Click on Home at the top and then click Wireless on the left side.

Step 5 Security: Select WEP.
Authentication: Select Open System to communicate the key across the
network. Select Shared Key to limit communication only to those devices that
share the same WEP settings.
WEP Encryption: Select 64-bit or 128-bit WEP encryption.
Key Type: Select Hexadecimal or ASCII key type
Keys 1-4: Input up to four encryption keys. You will select one of these to be
the active key.

Step 6 Click Apply to apply the changes.

Step 7 Click Tools >> System >> Save & Reboot

-------------------------------------------------
>>> DWL-G700AP How to upgrade the firmware of the DWL-G700AP

Step 1 Download the firmware and save the file to your computer. Do not try to run or launch the
file - it will not work.
Please go to the following URL to download the firmware : -
http://www.dlink.in.th/products/support.asp?pid=383#firmware

Step 2 Connect your DWL-G700AP using the UTP ( network ) cable.
There are two ways to do it :
a) PC connects to DWL-G700AP directly:
b) PC and DWL-G700AP connect to router:

Step 3 Launch your web browser, enter the IP address of DWL-G700AP (default is 192.168.0.50)
and press Enter.

Step 4 Enter the username (“admin” by default) and your password (blank by default). Click OK
to enter the web-based configuration for the device.

Step 5
A) Click on “Tools”
B) Click on “Firmware”
C) Under Firmware Upgrade click on the “Browse” button and browse to the .bin file you
downloaded in Step 1. Highlight the file by clicking on it once and click Open. (File name should
be : - DWL-G700AP_repeater_beta_210r14_0330.bin)
D) Click Apply. It will take 1 or 2 minutes for the upgrade to complete. Click on the Continue
button

Step 6 After the access point reboots, close your web browser. Please do a hard reset on the
Access Point after it rebooted. To do this, press and hold the Reset button which located at the
back of the Access point for 7 seconds, please make sure the Access point is power on while you
are resetting the Access point.

Step 7 At this point, your DWL-G700AP will be reset to default. The IP Address of the DWLG700AP
will be 192.168.0.50. If the IP Address is not in the same range as your network, you will
need to configure your network card to a static IP Address in order to configure the DWL-
G700AP. Please refer to Part 2 of this manual for configuring a static IP Address on your network
card.

-------------------------------------------------

DWL-G520

2010-05-12T21:21:00.001+07:00

DWL-G510

2010-05-12T21:20:00.003+07:00

>>> DWL-G510 How do I install the DWL-G510/DWL-G630?

Step 1 Insert the installation CD of DWL-G510/DWL-G630 in your CD-ROM drive. Setup will be launched automatically.

Step 2 Click Install Driver.

Step 3 Please wait while InstallShield? Wizard prepares for setup.

Step 4 Click Next

Step 5 Default setup will install to : Local Disk:\Program Files\D-Link AirPlus G, where Local Disk represents the drive letter of your hard drive.
To install to a different location click Browse and specify the location. Click Next.

Step 6 Setup will now install.

Step 7 When setup is completed Select No, I will restart... and then click Finish, and shut down your computer manually.

Step 8 Once off, insert the DWL-G510 into a PCI slot on your computer or DWL-G630 into a PCMCIA slot on your laptop. Power on your computer. Once rebooted, the drivers will install automatically.

Step 9 The two notifications below will popup in the system tray (the area by the clock in the lower right hand side of the screen):

Step 10 Next, the Found New Hardware Wizard window will appear. Select Install the software automatically (Recommended) using the radio buttons and then click Next.

Step 11 The Please wait while the wizard searches... window will appear.

Step 12 If the Device has not passes Windows? logo testing window appears click Continue Anyway.

Step 13 The Please wait while the wizard installs the software window will appear.

Step 14 Click Finish. Your adapter is now installed.

------------------------------------------------

DWL-G132

2010-05-12T21:20:00.001+07:00

DWL-G630

2010-05-12T21:19:00.006+07:00

>>> DWL-G630 How do I install the DWL-G510/DWL-G630?

Step 1 Insert the installation CD of DWL-G510/DWL-G630 in your CD-ROM drive. Setup will be launched automatically.

Step 2 Click Install Driver.

Step 3 Please wait while InstallShield? Wizard prepares for setup.

Step 4 Click Next

Step 5 Default setup will install to : Local Disk:\Program Files\D-Link AirPlus G, where Local Disk represents the drive letter of your hard drive.
To install to a different location click Browse and specify the location. Click Next.

Step 6 Setup will now install.

Step 7 When setup is completed Select No, I will restart... and then click Finish, and shut down your computer manually.

Step 8 Once off, insert the DWL-G510 into a PCI slot on your computer or DWL-G630 into a PCMCIA slot on your laptop. Power on your computer. Once rebooted, the drivers will install automatically.

Step 9 The two notifications below will popup in the system tray (the area by the clock in the lower right hand side of the screen):

Step 10 Next, the Found New Hardware Wizard window will appear. Select Install the software automatically (Recommended) using the radio buttons and then click Next.

Step 11 The Please wait while the wizard searches... window will appear.

Step 12 If the Device has not passes Windows? logo testing window appears click Continue Anyway.

Step 13 The Please wait while the wizard installs the software window will appear.

Step 14 Click Finish. Your adapter is now installed.

-------------------------------------------------

DWL-G122

2010-05-12T21:19:00.005+07:00

>>> DWL-G122 How to configure key in WEP/WPA-PSK in my Dlink Utility.

Step 1: Log into the D-Link utility by double-clicking on the TV or green D icon in the system tray (next to the clock).

Step 2: Clicks on Site Survey.

Step 3: Under the available network, select your own SSID and double click it.

Step 4: Double check that the SSID is correctly set.

Step 5: Data Encryption select Enable.

Step 6: Authentication select Open if you are setting WEP on the Router or select WPA-PSK if the Router is set as WPA-PSK.

Step7: Select the appropriate Key length which has to be match with the router settings.

Step8: Specify the correct encryption settings and encryption key.

Step9: Click on the Apply button to save the changes.

-------------------------------------------------
>>> Problem - No light on the DWL-G122

Troubleshooting Steps:
A. Uninstall the driver and reinstall the driver.
B. Install the device on another computer and check if the device is still functioning.
C. RMA

-------------------------------------------------
>>> Problem - Can’t see any SSID under available network.

Troubleshooting Steps:
1. Uninstall the driver and reinstall the driver.
2. Verify that the Link and the Act light is blinking.
3. Check the driver, please install the latest.
4. Make sure the router wireless network wireless signal is Enable.
5. Use the Dlink Utility to scan for the available network.
6. Place the device near to the router. And try again.
7. Try to use WZC (window to scan and configure for the wireless network)instead of using the Dlink utility.
8. Make sure that Firewall and other internet security application is OFF.
9. There should not have two wireless network card installed in a single computer. Please uninstall the previous driver.
10. Try this device at the hotspot to verify if the device is faulty or not.
11. RMA.

-------------------------------------------------
>>> Problem - Why I can’t see the D icon on my taskbar, so I can’t follow the instructions to configure my adaptor.

Troubleshooting Steps:
A. Please ensure that the driver is installed before plug in the device.
B. Please try another USB port or another computer.
C. Please ensure user is using the latest driver.
D. Try to disable Window Zero Configuration page.

Step 1: Click on Start and right-click on My Computer. Select Manage.

Step 2: In the left pane, double-click on Services and Applications. Select Services.

Step 3: In the right pane, scroll down and double-click on Wireless Zero Configuration to open the properties window.

Step 4: In the properties window, click on the General tab at the top. Next to Startup Type, click the down arrow and select Disabled. This will prevent the utility from running when you reboot your computer. Under Service Status, click Stop. Click OK to close the properties window.

Step 5: Please restart your PC. And you should be able to see the “D” icon (or Bar Chart depends on the wireless adapter model you have).

E. RMA.

-------------------------------------------------

DWL-G120

2010-05-12T21:19:00.003+07:00

DWL-3500AP

2010-05-12T21:18:00.006+07:00

***NOTE: Please take note that our DWL-3500AP and DWL-8500AP doesn't support WDS,
WDS+AP or Repeater.

-------------------------------------------------

DWL-3200AP

2010-05-12T21:18:00.005+07:00

>>> DWL-3200AP Basic/Installation Configuration

((( Fix ip address )))
Advise Step by Step
Please connect by lan cable and Fixed IP address
IP 192.168.0.51 ,Subnet Mask 255.255.255.0 ,Gateway 192.168.0.50
After configuration , change ip address is Obtain ip address an automatically.

------------------------------------------------

After login Goto Home > Basic Settings > Wireless

Wireless Band: IEEE 802.11g

Mode: Access Point is selected from the pull-down menu.

SSID: Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. The SSID can be up to 32 characters and is case-sensitive.

SSID Broadcast: Enable or Disable SSID broadcast. Enabling this feature broadcasts the SSID across the network.

Channel: Auto Channel Scan is set by default. All devices on the network must share the same channel. To change the channel, uncheck Auto Channel Scan. (Note: The wireless adapters will automatically scan and match the wireless setting.)

Auto Channel Scan: Select Enable or Disable. (Enable this feature to auto-select the channel for best wireless performance.)

Authentication: Open System
Shared Key
Open System/Shared Key
WPA-Enterprise
WPA-Personal
WPA2-Enterprise
WPA2-Personal
WPA-Auto-Enterprise
WPA-Auto-Personal
Home > Basic Settings > Wireless (continued)
Select Open System to communicate the key across the network.
Select Shared Key to limit communication to only those devices that share the same WEP settings.
Select Open System/Shared Key to allow either form of data encryption.
Select WPA-Enterprise, WPA2-Enterprise, WPA-Auto-Enterprise to secure your network with the inclusion of a RADIUS server.
Select WPA-Personal, WPA2-Personal, WPA-Auto-Personal to secure your network using a password and dynamic key changes. (No RADIUS server required).

Encryption: Select Disabled or Enabled. (Disabled is selected here).

Key Type*: Select HEX or ASCII.

Key Size:Select 64-, 128-, 152-bits.

Valid Key: Select the 1st through the 4th key to be the active key.

First through Fourth keys: Input up to four keys for encryption. You will select one of these keys in the valid key field.
*Hexadecimal digits consist of the numbers 0-9 and the letters A-F
*ASCII (American Standard Code for Information Interchange) is a code for representing English letters as numbers from 0-127

-------------------------------------------------
>>> DWL-3200AP How to configuration WDS Mode?

1. Connect your PC to the LAN port of your DWL-3200AP.
2. Start up a Internet explorer and key in 192.168.0.50 (by default)
3. Enter the Username: "admin" , Password: ""
4. Click on the Home tab.
5. Select Basic settings >> wireless
6. Select Mode is WDS.
7.Fill remote AP MAC Address and scan wireless signal.
8. Select Authentication follow assigned router.
9. Select Encryption is Enable.
10. Select Ket type is HEX.
11. Select Key size is 64Bits
12. Fill password in Firstkey follow assigned router.
13. Click Apply button below.

---------------------------------------------------------

***NOTE: Please take note that our DWL-3200AP can support the following modes like
AP, WDS , WDS+AP

---------------------------------------------------------

DWL-3260AP

2010-05-12T21:18:00.003+07:00

DWL-2100AP

2010-05-12T21:17:00.008+07:00

>>> DWL-2100AP How to set Access point (WEP)?

Step 1 Connect the DWL-2100AP to your PC using an Ethernet cable.

Step 2 Your computer will need to be in the same IP address range as the DWL-2100AP for configuration. The default IP address is 192.168.0.50.

Please connect by lan cable and Fixed IP address
IP 192.168.0.51 ,Subnet Mask 255.255.255.0 ,Gateway 192.168.0.50
*** Note : After configuration , change ip address is Obtain ip address an automatically.

Step 3 Open a web browser and enter in the IP address of the access point (192.168.0.50). The username is admin (all lower case) and the password is blank (nothing).

Step 4 Click on Home at the top and then click Wireless on the left side.

>>> Access Point (WEP)

Wireless Band: IEEE 802.11g.

Mode: Access Point is selected from the drop-down menu.

SSID: Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.

SSID Broadcast: Enable or Disable SSID broadcast. Enabling this feature broadcasts the SSID across the network.

Channel: Auto Channel Scan is enabled by default. All devices on the network must share the same channel.

Radio Frequency: The radio frequency will vary depending on the wireless channel that is chosen. The frequency in channel 6 is 2.437GHz.

Auto Channel Scan: Select Enable or Disable. Enable this feature to auto-select the channel for best wireless performance.

Authentication: Select Open System to communicate the key across the network.
Select Shared Key to limit communication to only those devices that share the same WEP settings.
Select Open System/Shared Key to allow either form of data encryption.
Select WPA-EAP to secure your network with the inclusion of a RADIUS server.
Select WPA-PSK to secure your network using a password and dynamic key changes (No RADIUS server required).
Select WPA2-EAP to secure your network with the inclusion of a RADIUS server and upgrade the encryption of data with the Advanced Encryption Standard (AES).
Select WPA2-PSK to secure your network using a password and dynamic key changes. No RADIUS server required and encryption of data is upgraded with the Advanced Encryption Standard (AES).
Select WPA-Auto-EAP to allow the client to either use WPA-EAP or WPA2-EAP.
Select WPA-Auto-PSK to allow the client to either use WPA-PSK or WPA2-PSK.

Super G Mode: Disabled by default. You can select Super G without Turbo or Super G with Dynamic Turbo.

Encryption: Select Disabled or Enabled. (Disabled is selected here).

Key Type: Select HEX or ASCII.

Key Size: Select 64-bit, 128-bit, or 152 bits.

Valid Key: Select the 1st through the 4th key to be the active key.
First through Fourth keys: Input up to four keys for encryption. You will select one of these keys in the valid key field.

Step 5 Click Tool >> System

Step 6 Click restart button

-------------------------------------------------
>>> DWL-2100AP Repeater Mode Configuration

Step 1 Connect the DWL-2100AP to your PC using an Ethernet cable.

Step 2 Your computer will need to be in the same IP address range as the DWL-2100AP for configuration. The default IP address is 192.168.0.50.

Step 3 Open a web browser and enter in the IP address of the access point (192.168.0.50). The username is admin (all lower case) and the password is blank (nothing).

Step 4 Click on Advanced at the top and then click Mode on the left side.

Step 5 Select "AP Repeater mode"

Step 6 AP Repeater will allow you to repeat the wireless signal of the root AP. Click to enable and enter the MAC address of the root AP.

Step 7 Click Apply

Step 8 Click on Tools at the top and then click System on the left side.

Step 9 Click Restart button.

-------------------------------------------------
>>> DWL-2100AP How to connect DWL-2100AP as Client Mode?

Step 1 Connect the D-Link Access Point directly to the PC via an Ethernet cable. One end to LAN port of the Access Point and the other end to the Ethernet port of you PC.

Step 2 Set you PC to Static IP. This can be done under Control Panel > Network Connections > Local Area Connection > Properties > Internet Protocol (TCP/IP) > Properties.
-Right-click on the Local Area Connection which represents your network card and select Properties.
-Highlight Internet Protocol (TCP/IP) and click Properties.
-Click Use the following IP address and enter an IP address that is on the same subnet as the LAN IP address on your D-Link Access
IP Address: 192.168.0.52, Subnet mask: 255.255.255.0
You don’t have to key in any Default gateway or DNS server address.
-Click OK twice. You may be asked if you want to reboot your computer. Click Yes.

Step 3 Launch your IE (Internet explorer) and key in 192.168.0.50 in the address column and press enter.

Step 4 Enter your Username: admin and no password (if it is default) click on OK

Step 5 Click on the Home tab and then click on Wireless to the left.

Step 6 Select “AP Client” on Mode.

Step 7 Click on the Scan button to Scan for the SSID of your wireless router/ access point.
Please make sure that the SSID and Channel is Same from you D-Link AP or Router. (If you have set wireless security such as WEP in the AP or router, you also need to set the same WEP on the Access Point)
Please key in the MAC Address of the Main AP to the “Root AP MAC Address”

Step 7 Click on Apply then click Continue to save the settings.

Step 8 Click on the Home tab and then click on LAN to the left
Change the IP Address of the D-Link Access Point so that it will be in the same subnet as you main Router (example: 192.168.1.51) and subnet mask (example:255.255.255.0) accordingly. Default Gateway has to be your main router’s IP address.

Step 9 Click on Apply then click Continue to save the settings.

Step 10 After you have done the above, please disconnect the D-Link Access Point from your PC and connect to the main router.

Step 11 Please make sure that you connect the D-Link Access Point to the LAN port of your computer or the device you want to use.

Step 12 Please put you PC back to automatically obtain IP address.This can be done under Control Panel > Network Connections > Local Area Connection > Properties > Internet Protocol (TCP/IP) > Properties.
-Right-click on the Local Area Connection which represents your network card and select Properties.
-Highlight Internet Protocol (TCP/IP) and click Properties.
-Click Obtain an IP address Automatically and click on Obtain DNS server address automatically.
-Click OK twice. You may be asked if you want to reboot your computer. Click Yes.

-------------------------------------------------

DWL-2000AP+

2010-05-12T21:17:00.007+07:00

>>> DWL-2000AP+ How to setup DWL-2000AP+ on Repeater mode?

1) Plug the power cord to the DWL-2000AP+ and switch on your power socket

2) Use the network cable (included in the package) to connect to both PC/notebook and
DWL-2000AP+

3) After your have connected the network cable between DWL-2000AP+ and the
PC/notebook (powered up), you will notice that all the 3 LEDs are lit up on the front
panel of DWL-2000AP+

4) On your PC/notebook, click onto “Start” and click on “Control Panel”

5) Double-click onto “Network Connections”

6) Right-click onto “Local Area Connection” and click on “Properties”

7) Select “Internet Protocol (TCP/IP)” and click onto “Properties”

8) Select “Use the following IP address” and assign:
IP address: 192.168.0.51
Subnet mask: 255.255.255.0
Then click “Ok”

9) Close onto “Close” button

10) Double-click on Internet Explorer, and type in 192.168.0.50
Type in “admin” as Username and left it blank (nothing) for Password

11) If you need to change the IP address of your DWL-2000AP+, please click onto
“LAN” button under Home tab, and change according to suit your existing network

12) If you intend to enable the DHCP Server function (this feature allow DWL-2000AP+
to assign IP addresses to the PC/notebook automatically), please click onto “DHCP”
button under Home tab

13) By default, DWL-2000AP+ is in Access Point mode, you may change to other
available modes by clicking onto “Mode” button under Advanced tab

14) For the next few setup, you may require to check for the MAC address of the Access
Point or Wireless Router. For DWL-2000AP+’s MAC Address, it is being labelled at the
bottom of the AP

15) If you wish to setup DWL-2000AP+ to be repeater (to extend the wireless coverage
of a existing DWL-2000AP+/ DI-624+ / DI-724P+) , then click onto “Mode” button
under Advanced tab, select “Repeater”

16) After selecting the “Repeater” mode, type in the MAC address of the Access point/
wireless router that you wish to use the DWL-2000AP+ to repeat from. Please ensure that
both SSID and Channel are the same for both AP and repeater

-------------------------------------------------

DWL-2700AP

2010-05-12T21:17:00.006+07:00

DWL-2700AP

2010-05-12T21:17:00.005+07:00

DWL-2000AP

2010-05-12T21:16:00.006+07:00

>>> DWL-2000AP How to setup DWL-2000AP on Client mode?

***NOTE: D-Link currently supports the DWL-2000AP connecting in client mode to another DWL-2000AP. The DWL-2000AP cannot be a client to other wireless routers or access points.

To configure the DWL-2000AP for Client mode follow the steps below:

Step 1 Log into the web based configuration by typing in the IP address of the DWL-2000AP (default:192.168.0.50) in your web browser. The username is admin (all lowercase) and the password is blank (nothing).

Step 2 Click on the Advanced tab and click on Mode.

Step 3 Select Client Mode and enter the Remote AP MAC. The remote AP MAC is the MAC address of the access point or wireless router you are connecting to.

***Note: Make sure when connecting to a wireless router, use the LAN or Ethernet MAC address, not the Wireless MAC address.

Step 4 Click the Apply button and click Continue to restart the DWL-2000AP.

-------------------------------------------------

DWL-1800

2010-05-12T21:16:00.003+07:00

DWL-1750

2010-05-12T21:16:00.001+07:00

DWL-700AP

2010-05-12T21:15:00.003+07:00

DWL-520_AirPlus

2010-05-12T21:15:00.001+07:00

DWL-510

2010-05-12T21:14:00.005+07:00