EMBEDDED AND ROBOTICS

Communication

2012-07-15T18:41:00.001+05:30

Communication refers to the interaction between two devices in embedded system. It can be between computer and microcontroller or between two microcontrollers.

Data Transfer

There are many techniques , different data transfer technique are used in different situations. Some example of data transfer is

• Simple parallel transfer‐Used to transfer 8, 16, and 32 etc bits of data in the same time.

• Asynchronous Serial Transfer (USART) –It is an old but still in use mode of serial communication uses only 2 lines (+1 additional line for GND).

• SPI - Serial Peripheral Interface ‐ It is a standard mode of communication between different

ICs.

• USB - A very advance, high speed and complicated serial Bus used in PCs to connect almost anything to it.

Classification

Modes of Data Transfer can be divided into two types:

1. PARALLEL TRANSFER In this mode a number of bits (say 8,16 or 32) are transferred at a time. Thus they require as many electrical line as the number of bits to be transferred at once.

2. SERIAL TRANSFER In this mode only one bit is transfer at once. So to transfer 8 bits, 8 cycles are required.

Modes of Data Transfer can also be divided into

1. SYNCHRONOUS TRANSMISSION‐.

2. ASYNCHRONOUS TRANSMISSION

____________________________________________________________________________

Baud Rate

Baud Rate is a measurement of transmission speed in asynchronous communication. Devices that allow the communication must all agree on a single speed of information its unit is 'bits per second'.

____________________________________________________________________________

Summery

Transmission	Advantages	Disadvantages
Asynchronous	Simple & Inexpensive	High Overhead
Synchronous	Efficient	Complex and Expensive

____________________________________________________________________________

Different Communication Techniques

Simplex : one sided communication like radio

Half duplex: like walkie talkie

Full duplex : video conferencing

Timers

2012-07-06T12:21:00.002+05:30

Timer is an 8 bit register that keeps on increasing its value, so one of the basic conditions is the situation when timer register OVERFLOWS i.e. it has counted up to its maximum value (255 for 8 BIT timers) and rolled back to 0. In this situation timer can issue an interrupt and you must write an Interrupt Service Routine (ISR) to handle the event. There are three different timers available in Atmega16 and all the timers work in almost same way. They are TIMER0, TIMER1 and TIMER2.

Prescalar

The Prescalar is a mechanism for generating clock for timer by CPU clock.

Atmega has clocks of several frequencies such as 1 MHz, 8 MHz, 12 MHz, 16 MHz (max). The Prescalar is used to divide this clock frequency and produce a clock for TIMER. The Prescalarcan be set to produce the following types of clocks:

No Clock(Timer stop)

No prescaling (clock frequency = CPU frequency) FCPU/8

FCPU/64

FCPU/256

FCPU/1024

External clock

Timer Mode

Timers are usually used in one of the following modes:

Normal

CTC

Fast PWM

Phase correct PWM

Normal Mode

A timer running in normal mode will count up to its maximum value. When it reaches this maximum value, it issues an Overflow interrupt and resets the value of the timer to its original value.

In the above case, you can see that the time period is 256 times the time period of the clock. 255 clock cycles are required to attain the maximum value and one clock cycle to clear the timer value.

So, ftimer = fclock / 256

this mode has its limitations. We are confined to a very small set of values of frequency for the timer. This limitation is overcome by the compare mode.

CTC Mode

(clear timer on compare match)

Compare mode makes use of a register known as the Output Compare Register which stores a value of our choice. The timer continuously compares its current value with the value on the register and when the two values match, the timer resets itself to 0.

In that case, the output pin will remain high for one time period of the timer and will remain low for another time period.

So,

tout = 2 * ttimer

From the normal case, we can draw an analogy to find out ttimer.

ttimer = tclock * (OCR + 1)

So, finally, we have the frequency as,

fout = fclock / (2 * (OCR + 1) )

Pulse Width Modulation (PWM) Mode

if you want to control the brightness of an LED (or any lamp), or the speed of DC motor, then digital on/off signals will not suffice. This situation is very smartly handled by a technique called as PWM or Pulse Width Modulation.

PWM is the technique used to generate analog signals from a digital device like a MCU.

In AVR microcontrollers, PWM signals are generated by timers. There are two methods by which you can generate PWM from timers:

1. Fast PWM

2. Phase Correct PWM

1.Fast PWM

Now for PWM generation from this count sequence OCR0 (Output Compare Register Zero) is used (Zero because it is for TIMER0 and there are more of these for TIMER1 & TIMER2). We can store any value between 0‐255 in OCR0, say we store

64 in OCR0 then it would appear in the graph as follows (the RED line).

When the TIMER0 is configured for fast PWM mode, then, while the timer is counting up, whenever the value of TIMER0 counter matches the value in the OCR0 register, an output PIN is pulled low (0) and when counting sequence begin again from 0 it is SET again (pulled high=VCC). This PIN is named OC0 and you can find it in the PIN configuration of ATmega

From the figure, you can see that a wave of duty cycle of 64/256 = 25% is produced by setting OCR0 to 64. You can set OCR0 to any value and get a PWM of duty cycle of (OCR0 / 256). When you set it to 0 you get a 0% duty cycle while setting it to 255 will give you a 100% duty cycle output. Thus by varying duty cycle you can get an analog voltage output from the OC0 PIN.

In the inverting mode the value of the OC0 pin is just the reverse of that in the above figure.

Phase Correct PWM Mode

This mode is very similar to the Fast PWM mode except that whenever the value of the timer reaches its maximum value then instead of clearing the value of the timer it simply starts counting down.

Overview of timers

SETTING TIMERS IN CVAVR :

Assignment on ADC

2012-07-03T16:43:00.000+05:30

MAKE PROGRAMS:

GLOW LED ACCORDING TO INPUT TO ADC

0-99 1 LED

100-150 2LED

151-200 3 LED

200-255 4LED

2. MAKE DIGITAL VOLTMETER

3. MAKE DIGITAL WATTMETER

see answer here

ADC Analog to Digital convertor

2012-07-03T13:33:00.000+05:30

What we have seen till now that the input given to uC was digital, i.e., either +5 V (logic 1) or 0V (logic 0). But what if we have an analog input, i.e., value varies over a range, say 0V to +5V? Then we require a tool that converts this analog voltage to discrete values. Analog to Digital Converter (ADC) is such a tool.

ADC is available at PORTA of Atmega16.
CLICK HERE FOR PIN DIAGRAM
Thus we have 8 pins available where we can apply analog voltage and get corresponding digital values. The ADC register is a 10 bit register, i.e., the digital value ranges from 0 to 1023. But we can also use only 8 bit out of it (0 to 255) as too much precision is not required.
Reference voltage is the voltage to which the ADC assigns the maximum value (255 in case of 8 bit and 1023 for 10 bit). Hence, the ADC of Atmega16 divides the input analog voltage range (0V to Reference Voltage) into 1024 or 256 equal parts, depending upon whether 10 bit or 8 bit ADC is used. For example, if the reference voltage is 5V and we use 10bit ADC, 0V has digital equivalent 0,
+5V is digitally 1023 and 2.5V is approximately equal to 512.

ADC =Vin x 255/Vref (8 bit)
ADC =Vin x 1023/Vref (10 bit)

Function:

read_adc()
This function returns the digital value of analog input at that pin of PORTA whose number is passed as parameter, e.g., if you want to know the digital value of voltage applied at PA3, and then just call the function as,
read_adc(3);
If the ADC is 8 bit, it will return a value from 0 to 255. Most probably you will need to print it on LCD. So, the code would be somewhat like

int a; char c[10]; // declare in the section of global variables
a=read_adc(3);
itoa(a,c);
lcd_puts(c);

SETTING UP ADC:
FOR OLDER VERSION OF CVAVR:

FOR NEWER VERSION OF CVAVR:

click here for projects on adc

Getting Started With Proteus : simulation software

2012-07-02T19:42:00.002+05:30

adding microcontroller

adding lcd

to add switch, search for "button"
setting adc with proteus
led pattern circuit with proteus

Assignment on Pograms for lcd

2012-07-02T18:33:00.001+05:30

1) Print a character on lcd

2) Print your name

3) Print a to z

4) Blink a character on lcd

5) Print a b c d…z on only 1 coordinate after delay of 100ms

6) Moving name

7) Print name on pressing switch

8) Make clock

9) Make calendar: having condition of leap year and leap year of century, each month having appropriate days.

for answers click here

Getting Started With CVAVR

2012-07-01T17:22:00.000+05:30

DOWNLOAD CVAVR HERE

if you want to interface lcd also:

setting up adc : click here

SETTING UP TIMERS :CLICK HERE

ASSIGNMENT 1 -CONTROLLING LEDs

2012-07-01T13:16:00.000+05:30

questions:

GLOW A SINGLE LED
GLOW 8 LED OF A PORT
BLINKING A SINGLE LED
BLINKING 8 LED OF A PORT
ALTERNATE GLOWING LED s
GLOWING LED IN INCREASING PATTERN
GLOWING LED IN DECREASING PATTERN
GLOWING LED IN CONVERGING PATTERN
GLOWING LED IN DIVERGING PATTERN
BOTH CONVERGING AND DIVERGING PATTERN
INCREASING AND DECREASING PATTERN
WITH A SWITCH GLOW 1 LED
WITH A SWITCH GLOW ALL 8 LEDS
WITH 4 DIFFERENT SWITCH GLOW 4 DIFFERENT PATTERN
WITH 1 SWITCH GLOW 4 DIFFERENT PATTERN

1ST TRY YOURSEELF

CHECK ANSWERS HERE

Introducing DELAY

2012-06-29T19:03:00.000+05:30

INTRODUCES TIME DELAY IN PARTICULAR STEP.

header file required : #include<delay.h>

syntax: delay_ms(200); // where delay is 200 milli seconds

Interfacing an LCD

2012-06-29T19:00:00.001+05:30

Lcd

a 16 pin lcd have following pin connection

Printing Functions

Now once the connections have been made, we are ready to display something on our screenSome of the general LCD functions which you must know are:

lcd_clear()

Clears the lcd. Remember! Call this function before the while(1) loop, otherwise you won’t be able to see anything!

lcd_gotoxy(x,y)

Place the cursor at coordinates (x,y) and start writing from there. The first coordinate is (0,0). Hence, x ranges from 0 to 15 and y from 0 to 1 in our LCD.

Example: you want to display something starting from the 5th character in second line, then the function would be

lcd_gotoxy(5,1);

lcd_putchar(char c)

To display a single character.

E.g.,

lcd_putchar(‘H’);

lcd_putsf(constant string)

To display a constant string.

Eg,

lcd_putsf(“IIT Kanpur”);

lcd_puts(char arr)

To display a variable string, ie an array of characters (data type char) in C language .

e.g., You have an array char c[10] which keeps on changing. Then to display it, the function would be called as

lcd_puts(c);

Now we have seen that only characters or strings (constant or variable) can be displayed on the LCD. But quite often we have to display values of numeric variables, which is not possible directly. Hence we need to first convert that numeric value to a string and then display it. For e.g., if we have a variable of type integer, say int k, and we need to display the value of k (which changes every now and then, 200 now and 250 after a second... and so on). For this, we use the C functions itoa() and ftoa(), but remember to include the header file <stdlib.h> to use these C functions.

itoa(int val, char arr[])

It stores the value of integer val in the character array arr. E.g., we have already defined int i and char c[20], then

itoa(i,c);

lcd_puts(c);

Similarly we have

ftoa(float val, char decimal_places, char arr[])

It stores the value of floating variable f in the character array arr with the number of decimal places as specified by second parameter. E.g., we have already defined float f and char c[20], then

ftoa(f,4,c); // till 4 decimal places

lcd_puts(c);

Now we are ready to display anything we want on our LCD. Just try out something which you would like to see glowing on it!

header file required : #include<lcd.h> //but it is not required as it is already applied by cvavr by selecting lcd

HOW TO SELECT LCD:

get started with lcd on cvavr

Registers - DDR , PORT , PIN

2012-06-29T16:46:00.000+05:30

All the configurations in microcontroller is set through 8 bit (1 byte) locations in RAM (RAM is a bank of memory bytes) of the microcontroller called as Registers.

Input Output functions are set by Three Registers for each PORT.

• DDRX (DATA DIRECTION REGISTER)‐‐‐‐> Sets whether a pin is Input or Output of PORTX.

• PORTX ‐‐‐> Sets the Output Value of PORTX.

• PINX ‐‐‐‐‐> Reads the Value of PORTX.

DDR:

First of all we need to set whether we want a pin to act as output or input. DDRX register sets this.

• To make Input set bit 0

• To make Output set bit 1

example DDRB=11010001

(PORT‐B)

PB7 Output 1

PB6 Output 1

PB5 Input 0

PB4 Output 1

PB3 Input 0

PB2 Input 0

PB1 Input 0

PB0 Output 1

to make a whole 8 bit port as input or output:

DDRA=255 (FOR OUTPUT PORT: 255 IS USED AS IT IS 8PIN ie 8 BIT PORT{2^8})

DDRA=0 (FOR MAKING INPUT PORT)

To make an individual pin of port as input or output:

syntax DDRA.X=0; (INPUT) // WHERE X IS THE PIN NO. starting from 0 to 7

DDRA.X=1; (OUTPUT)

example: DDRC.5=1; //IT MAKES 5TH PIN OF PORT C AS OUTPUT PIN

-----------------------------------------------------------------------------------------------------------------------

PORT:

This register sets the value to the corresponding PORT. Now a pin can be Output or Input. So let’s discuss both the cases.

• Output Pin

If a pin is set to be output, then by setting bit 1 we make output High that is +5V and by setting bit 0 we make output Low that is 0V.

SYNTAX:

PORTX ‐‐‐‐> to set value of PORTX with a byte.

PORTX.y ‐‐> to set value of yth pin of PORTX with a bit (works only with CVAVR)

example: PORTA.4=0; //GIVE 0 VOLT AT OUTPUT OF PIN 4 OF PORT A

PORTB=255; //GIVE 5 VOLT AT OUTPUT OF ALL PINS OF PORT B

• Input Pin

If a pin is set to be input, then by setting its corresponding bit in PORTX register will make it as follows, Set bit 0 ‐‐‐> Tri‐Stated Set bit 1 ‐‐‐> Pull Up

Tristated means the input will hang (no specific value) if no input voltage is specified on that pin.

Pull Up means input will go to +5V if no input voltage is given on that pin. It is basically connecting

PIN to +5V through a 10K Ohm resistance.

----------------------------------------------------------------------------------------------------------------------

PIN register:

This register is used to read the value of a PORT. If a pin is set as input then corresponding bit on PIN register is,

• 0 for Low Input that is V < 2.5V

• 1 for High Input that is V > 2.5V (Ideally, but actually 0.8 V ‐ 2.8 V is error zone!)

SYNTAX:

• PINX ‐‐‐‐> Read complete value of PORTX as a byte.

• PINX.y ‐‐> Read yth pin of PORTX as a bit (works only with CVAVR).

example if(PINA.1==1)

{

___

}

// READ IF VALUE AT PIN 1 OF PORT A IS 1 OR NOT, IF IT IS 1 THEN IT EXECUTES INSTRUCTIONS UNDER if STATEMENT

-------------------------------------------------------------------------------------------------------------------------------------------

Atmega16 Pin Diagram And Explanation

2012-06-28T16:26:00.000+05:30

DOWNLOAD DATA SHEET CLICK HERE

• MOSI (Master Out Slave In)
• MISO (Master In Slave Out)
• SCK (Serial Clock)
• RESET
• GND (Ground)
Now connect the power supplies that are Vcc and GND to the micro controller.
Vcc = +5V and GND = 0V
Do not forget to connect Reset to Vcc with a 1K/10K resistor for pulling up. That is it we are ready with the hardware.
ATmega16 has 16 KB programmable flash memory, static RAM of 1 KB and EEPROM of 512 Bytes.

Pin No.	Pin name	Description	Alternate Function
1	(XCK/T0) PB0	I/O PORTB, Pin 0	T0: Timer0 External Counter Input. XCK : USART External Clock I/O
2	(T1) PB1	I/O PORTB, Pin 1	T1:Timer1 External Counter Input
3	(INT2/AIN0) PB2	I/O PORTB, Pin 2	AIN0: Analog Comparator Positive I/P INT2: External Interrupt 2 Input
4	(OC0/AIN1) PB3	I/O PORTB, Pin 3	AIN1: Analog Comparator Negative I/P OC0 : Timer0 Output Compare Match Output
5	(SS) PB4	I/O PORTB, Pin 4	In System Programmer (ISP) Serial Peripheral Interface (SPI)
6	(MOSI) PB5	I/O PORTB, Pin 5
7	(MISO) PB6	I/O PORTB, Pin 6
8	(SCK) PB7	I/O PORTB, Pin 7
9	RESET	Reset Pin, Active Low Reset
10	Vcc	Vcc = +5V
11	GND	GROUND
12	XTAL2	Output to Inverting Oscillator Amplifier
13	XTAL1	Input to Inverting Oscillator Amplifier
14	(RXD) PD0	I/O PORTD, Pin 0	USART Serial Communication Interface
15	(TXD) PD1	I/O PORTD, Pin 1	USART Serial Communication Interface
16	(INT0) PD2	I/O PORTD, Pin 2	External Interrupt INT0
17	(INT1) PD3	I/O PORTD, Pin 3	External Interrupt INT1
18	(OC1B) PD4	I/O PORTD, Pin 4	PWM Channel Outputs
19	(OC1A) PD5	I/O PORTD, Pin 5	PWM Channel Outputs
20	(ICP) PD6	I/O PORTD, Pin 6	Timer/Counter1 Input Capture Pin
21	PD7 (OC2)	I/O PORTD, Pin 7	Timer/Counter2 Output Compare Match Output
22	PC0 (SCL)	I/O PORTC, Pin 0	TWI Interface
23	PC1 (SDA)	I/O PORTC, Pin 1	TWI Interface
24	PC2 (TCK)	I/O PORTC, Pin 2	JTAG Interface
25	PC3 (TMS)	I/O PORTC, Pin 3
26	PC4 (TDO)	I/O PORTC, Pin 4
27	PC5 (TDI)	I/O PORTC, Pin 5
28	PC6 (TOSC1)	I/O PORTC, Pin 6	Timer Oscillator Pin 1
29	PC7 (TOSC2)	I/O PORTC, Pin 7	Timer Oscillator Pin 2
30	AVcc	Voltage Supply = Vcc for ADC
31	GND	GROUND
32	AREF	Analog Reference Pin for ADC
33	PA7 (ADC7)	I/O PORTA, Pin 7	ADC Channel 7
34	PA6 (ADC6)	I/O PORTA, Pin 6	ADC Channel 6
35	PA5 (ADC5)	I/O PORTA, Pin 5	ADC Channel 5
36	PA4 (ADC4)	I/O PORTA, Pin 4	ADC Channel 4
37	PA3 (ADC3)	I/O PORTA, Pin 3	ADC Channel 3
38	PA2 (ADC2)	I/O PORTA, Pin 2	ADC Channel 2
39	PA1 (ADC1)	I/O PORTA, Pin 1	ADC Channel 1
40	PA0 (ADC0)	I/O PORTA, Pin 0	ADC Channel 0

Port A (PA7 ‐ PA0): Port A serves as the analog inputs to the A/D Converter. Port A also serves as an 8‐bit bi‐directional I/O port, if the A/D Converter is not used. When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source current if the internal pull‐up resistors are activated. The Port A pins are tri‐stated when a reset condition becomes active, even if the clock is not running.

Port B (PB7 ‐ PB0): Port B is an 8‐bit bi‐directional I/O port with internal pull‐up resistors (selected for each bit). Port B also serves the functions of various special features of the ATmega16 as listed on page 58 of datasheet.

Port C (PC7 ‐ PC0): Port C is an 8‐bit bi‐directional I/O port with internal pull‐up resistors (selected for each bit). Port C also serves the functions of the JTAG interface and other special features of the ATmega16 as listed on page 61 of datasheet. If the JTAG interface is enabled, the pull‐up resistors on pins PC5(TDI), PC3(TMS) and PC2(TCK) will be activated even if a reset occurs.

Port D (PD7 ‐ PD0): Port D is an 8‐bit bi‐directional I/O port with internal pull‐up resistors (selected for each bit). Port D also serves the functions of various special features of the ATmega16 as listed on page 63 of datasheet.

RESET: Reset Input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running.

XTAL1: External oscillator pin 1

XTAL2: External oscillator pin 2

AVCC: AVCC is the supply voltage pin for Port A and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low‐pass filter.

AREF: AREF is the analog reference pin for the A/D Converter.

You can see it has 32 I/O (Input/output) pins grouped as A, B, C & D with 8 pins in each group. This group is called as PORT.

• PA0 ‐ PA7 (PORTA)

• PB0 ‐ PB7 (PORTB)

• PC0 ‐ PC7 (PORTC)

• PD0 ‐ PD7 (PORTD)

Notice that all these pins have some function written in bracket. These are additional function that pin can perform other than I/O. Some of them are.

• ADC (ADC0 ‐ ADC7 on PORTA)

• UART (Rx,Tx on PORTD)

• TIMERS (OC0 ‐ OC2)

• SPI (MISO, MOSI, SCK on PORTB)

• External Interrupts (INT0 ‐ INT2)

Programmer

2012-06-28T15:51:00.001+05:30

Programmer basically consists of two parts:

• Software (to open .hex file on your computer)
• Hardware (to connect microcontroller)

Hardware depends on the communication port you are using on the computer (Serial, Parallel or USB). I suggest beginners to use Serial Programmer as it is very easy to build. Software for that is Pony Prog. Some famous Windows (XP, Vista) programmers are:

• Pony Prog(Serial, Parallel)
• AVRdude(supports many hardware’s)
• AVRStudio (supports Atmel's hardware)
• ATProg (Serial)
• USB‐ASP (USB)

I will be using Atmega‐16 as default microcontroller because it very easily available and is powerful enough with sufficient number of pins and peripherals we use.

click here to download avr studio< click on register (for free)<download

AVR Programming (CVAVR)

2012-06-28T10:48:00.000+05:30

AVR(ADVANCE VIRTUAL RISC) is a modified HARWARD architecture 8 bit RISC single chip microcontroller which was developed by atmel in 1996. AVR was 1st to use on chip FLASH memory in microcontroller families for program storage

COMPILER /(IDE) INTEGRATED DEVELOPMENT ENVIRONMENT

ATMEL MICROCONTROLLER are very famous and easy to use. best software for coding atmel atmega is cvavr (CODE VISION AVR).
CLICK HERE TO DOWNLOAD FOR FREE

Basic Architecture of Microcontroller

2012-06-28T10:27:00.000+05:30

Architecture Broad classification

Embedded(self contained) 8 bit microcontroller
16 to 32 microcontroller
Digital signal processor

FEATURES OF MORDERN MICROCONTROLLER

Built in monitor program
Built in program memory
Interrupts
Analog I/O
Serial I/O
Facility to Interface External Memory
Timers

INTERNAL STRUCTURE OF MICROCONTROLLER(BLOCK DIAGRAM)

GOOGLY: HOW DOES MICROCONTROLLER WORKS?

WELL I CANNOT GO IN DETAIL ABOUT WORKING because it is a vast topic in itself. I can just give you a overview-

Microcontroller consist of a CPU which is interfaced to RAM and FLASH MEMORY. You just feed your program in flash memory of microcontroller. now when you turn microcontroller ON , CPU accesses the instruction from RAM which access your code from FLASH. Its sets the configuration of pins and starts performing according to your program.

HOW TO DO CODING/PROGRAMMING FOR MICROCONTROLLER?

YOU CAN WRITE PROGRAMS IN JAVA C++ AND C. THEN WE COMPILE THE CODE TO GENERATE ITS MACHINE LANGUAGE ie 0 and 1, NOW BURN IT IN MICROCONTROLLER USING A PROGRAMMER AND A SOFTWARE.

BETTER OPTION WOULD BE MAKING PROGRAM IN C AND THEN COMPILE IT IN MACHINE FILE(.hex) . AFTER THIS WE FEED PROGRAM IN FLASH MEMORY OF MICROCONTROLLER USING SUITABLE PROGRAMMER.

THIS PICTURE ABOVE IS A PROGRAMMER USE TO BURN OUR PROGRAM IN MICROCONTROLLER.

we will discuss about programs and softwares and hardwares to be used in upcoming post.

What is a Microcontroller ?

2012-06-27T18:31:00.000+05:30

A microcontroller is a programmable digital processor with necessary peripherals. Both microcontroller and microprocessor carry out job according to program/instruction, and both are complex sequential digital circuit.

---------------------------------------------------------------------------------

MICROCONTROLLER vs MICROPROCESSOR

MICROPROCESSOR ,unlike microcontroller requires external memory for instruction/program storage.
A microcontroller does not require additional interfacing ICs for operation and its function as a stand alone system.
A microcontroller has required on chip memory with associated peripherals.
A microcontroller clock speed is limited to few tens of megahz, while microprocessors have higher clock speed.

Embedded Systems : an introduction

2012-06-27T15:48:00.001+05:30

Embedded systems, unlike that of a general purpose computer (performing variety of task), is a scaled down computer system, contained on a single chip having both hardware and firmware, designed to perform operation to minimize human control.

DEFINITION:

an embedded system is special purpose computer system designed to perform one or a few dedicated function, often with real time computer constraints.

--------------------------------------------------------------------------------------------------

APPLICATION OF EMBEDDED SYSTEM:

Embedded system is also a control system

pen drives
hard disk
air conditioner
printer
mouse
fan
digital camera
automobile system
cell phone

----------------------------------------------------------------------------

Types of embedded system:

NON REAL TIME EMBEDDED SYSTEM is one in which there is no deadline, thus high performance or fast response is preferred.

example:

security system
mobile and PDA
alarm system
digital camera

REAL TIME EMBEDDED SYSTEM : where deadline is to be met ie task is to performed within time limit.

sensor system in nuclear plant
missile defense system
flight control system
anti collision system in auto mobile.

What is a Digital System

2012-06-27T15:09:00.002+05:30

Lets start with basic, ie .digital system. in electronics as you already know only 2 states are used - LOGIC HIGH and LOGIC LOW, represented by 1 and 0 respectively.

GOOGLY- Why assign '0' and '1' and not 'a' and 'b' or 'x' and 'y' or 'cat' and 'dog' etc.
answer- computation ease!
-----------------------------------------------------------------------------------------------------

Types of digital circuits:

Combinational circuits : output depends only on present states.eg logic gates.
Sequential circuits : next states is completely determined by past states.eg counter and flipflop.

----------------------------------------------------------------------------------------------------

Clock: building block of sequential circuit

A clock is simply high and low states of voltage with time ie essentially a square wave.

duty cycle: it is ratio of Ton and Toff.

Logic gates : building block of combinational circuit

these are essentially combinational circuitry used to implement boolean operation like AND OR NOT NAND NOR XOR XNOR etc.

---------------------------------------------------------------------------------------------