Emergency-Technology

Problem: Keyboard type extra letters

2009-12-09T00:32:00.002-08:00

Problem: Keyboard type extra letters

Possible Solution:

The keyboard circuit has been short maybe because of moist or some liquid .

1.Open the keyboard and clean it from inside, use alcohol in cleaning process.
2.If the problem is still present, I sugget to replace your keyboard to avoid
complication on the computer.

Problem: Epson Stylus CX6600 All-In-One InkJet Printer only print yellow

2009-12-09T00:32:00.001-08:00

Problem: Epson Stylus CX6600 All-In-One InkJet Printer only print yellow

Possible Solution :

1. Check the cartridge of your printer if it still
capable or having a sufficient ink to handle printing
2.If yes, purge your cartridge and run a maintenance page
3.Wipe the head of the cartridge on a wet cloth to remove some clogs.
4.And clean the tab circuit of the cartridge.

Problem: Printer won't print and can't delete the printer

2009-12-09T00:31:00.000-08:00

Problem: Printer won't print and can't delete the printer

Possible Solution: This a communication problem between the printer and computer or the
transfer of file.
1.Check the cable connecting your printer and your PC if it's working properly.
2.Restart your computer and then, log the computer in
administrator mode and after that, uninstall the printer
driver and, in order to install another driver you need to restart you PC again.

Problem: The printer is not communicating with the computer.

2009-12-07T05:55:00.002-08:00

Problem: The printer is not communicating with the computer.

Possible Solution:1. Transfer the cable connecting to the printer to the other slot on the computer.
2. Restart your computer and yoor printer.
3. Uninstall the printer driver and then restart your computer again after the restart install the printer driver.
4. here you go, it's working.

Problem : Replace a new cartridge and now the printer won't print at all.

2009-12-07T05:55:00.001-08:00

Problem : Replace a new cartridge and now the printer won't print at all.

possible solution :
1.First unplug and plug on the printer by pulling the power cord then on the printer again.
2.if nothing happens, Re-insert your cartridge.

Problem: Ink and paper lights are blinking red at the same

2009-12-07T05:54:00.000-08:00

Problem: Ink and paper lights are blinking red at the samePossible solution:

There are two possible solution to that problem, firmware issue or a mechanical.
in a firmware issue: your printer being triggered in the operation of sensing paper and ink, it can only saw low ink and no paper status at the tray.
and in the mechanical side, there is a problem on the sensing devices maybe they can only saw low ink and no paper status on the printer.

Problem: The printer only print one color

2009-12-07T05:53:00.001-08:00

Problem: The printer only print one color

Possible solutions:

1.Clean the tab circuit of your cartridge using wet clean cloth becuase some of the cartridge tab will fill with ink that cause some loss connection.
2.Wipe the head of the cartridge containing nozzles on a wet cloth(to remove clogs covering the nozzles)
3.If the cartridge have a low ink pls refill or replace a new one.
4.Perform a maintenance forge to the heads,
5.print a maintenance page.

LABVIEW 8.5 PROGRAMMING TUTORIAL

2009-12-04T07:49:00.001-08:00

LABVIEW 8.5

Getting Started

When you start LabView 8, you will see the Getting Started screen. Earlier versions may not have this screen and may automatically come up with a blank program. To get started trying things on your own, you will want to click "Blank VI" under the "New" Section on the left. "Empty Project" would start a new project. LabView Projects are a relatively new feature and not necessary to learn at this point. VI from Template is an advanced LabView feature which allows you to create templates as starting points for your development. Again, this is an advanced feature so we will skip it for now. You will start a "Blank VI" and in the future, you can open recently created LabView programs from the "Open" section.

A "VI" is a LabView program which is contained in a file with a .vi extension. Every time you create a LabView program you will end up saving a .vi file. This file is binary in nature so opening it in a text editor such as notepad will be of limited use.

When you start, you will typically see a "Front Panel" which is a window with a grey background:

This is the graphical user interface (GUI) for your program, where you (and others) will interact with it while it is running. It is definitely not much to look at yet, but it can be, and you will be surprised at how easy it is to build a nice interface quickly in LabView.

The "Block Diagram" appears to be similar to the "Front Panel" to a novice user , other than the fact that it has a white background instead of grey. In fact, this window is where the program will actually be written. When you develop the block diagram, you are actually writing the program that makes the front panel operate as you desire. It is here that you will make the computer perform calculations, write files, communicate with hardware, etc. This view of the VI is what most programmers would call a "program" or "source code".

Block Diagram:

You will notice that if you select one window or the other in LabView 8.5, you will see a context sensitive menu appear. There are menus associated with the Front Panel and Block Diagram that allow you to do everything you need to do to design your user interface and implement the logic that makes it work.

Block Diagram Menu

Front Panel Menu

To see how easy it is to design user interfaces, lets first go to the front panel. Once you do that, click on the menu where it says "Num Ctrls" and notice that you have navigated deeper in the menu system:

All the items at this level in the menu are "Controls". Controls are user interface elements that you can place on the Front Panel. There are also "Indicators" which are not shown in this menu. Controls allow you to input something into your program. That means you get to change the value and affect the program while it is running. Indicators output results from the program. You cannot change their value. They are your way of seeing what has happened.

If you click on "Num Ctrl" in the menu, you can then drop a control on the front panel that will allow you to enter a number. Its as easy as that.

Front Panel with Numeric Control dropped on it from the menu:

Now you will notice something automatically happened on the Block Diagram. A "terminal" appeared corresponding to the Control that was dropped. In your LabView code, this terminal represents the number entered on the front panel control. If you type in 3.2 in the control, then this terminal in your code is a representing that number. You will soon see that you can wire the terminal to other elements in the Block Diagram to create a picture that looks like a flowchart, schematic, or blueprint, which defines what the program should do. This terminal serves as a starting point for the value you have entered and you will be able to connect it to the input of another element.

Before we go further, lets look at how the menus operate so you know how to interact with it and explore the possibilities. You have seen the default menu for the front panel and block diagram, and you have used the front panel menu to place a numeric control. Lets start with this front panel menu. First, try right clicking on the front panel. You will see that the same menu appears as a pop up. Left click somewhere else to make it go away.

At the bottom of the menu you will see a strip like this:
If you click it, you will see that the menu expands providing you with a large number of submenus. The default menu gives you the options that National Instruments believes will be most common or make the program easiest to use for beginners. Many of these are "Express" menus which provide some built-in functionality. We are going to dig into classic LabView programming to make sure you get a solid foundation first. To do this, you will need to become familiar with expanding and navigating the menu as time goes on. You may find that it is easier to right click on the LabView windows to pop up menus as you need them rather than using the windowed ones.

Now try navigating to the full featured numeric control and indicator menu on the front panel. You should be able to use what you've learned to do that. Here is a picture that shows exactly how you navigate there in LabView 8.5. (Hint: Expand the menu)

You see the numeric indicator highlighted by the mouse cursor in the above screen capture. Remember, an indicator provides a value to the user rather than allowing the user to enter the value. Place an indicator in much the same way as you did the control. Select it from the menu and drop it on the user interface. You will see that an indicator terminal appears on the block diagram. You can distinguish the two by the thickness of the border around the terminal on the block diagram and by the color of the default background on the front panel (white for controls, grey for indicators).

Indicator Placed on Front Panel:

Both terminals visible on the Block Diagram:

I have run out of time for today, to continue this lesson just visit this URL : www.learnlabview.blogspot.com

MOVIE ANIME MANGA and GAMING WEBSITES

2009-12-04T07:47:00.001-08:00

Movie and Anime Websites	Gaming Browser Websites
http://www.anime6.org	http://www.officegamespot.com
http://www.free-tv-video-online.info/int...	http://www.thecontinuum.com
http://www.justvids.org/	http://www.ikariam.com
http://www.bedroommedia.com/	http://www.wardrome.com
http://www.movie6.net	http://www.travian.com
http://www.tv-links.co.uk	http://www.magicduel.com
http://www.torrentz.com	http://www.tribalwars.net
http://www.mininova.org	http://www.thewrestlinggame.com
http://www.animethunder.com	http://www.garena.com
http://www.megavideo.com	http://www.anime6.org
http://www.youtube.com	http://www.youranimenow.com
http://www.mangaviewer.com	http://www.chrunchyroll.com
http://www.crunchyroll.com
http://www.unrivaled.info
http://www.onemanga.com
http://www.youranimenow.com
http://www.watchnewfims.com
http://www.slyfoxtv.com/
http://www.vid-stream.com/movies/
http://mytheater.org/
http://www.movierumor.com/
http://movienetx.com/
http://www.plentyofvids.com/media/movies...
http://grabngovideo.com/
http://www.digaclip.com/
http://watch-movies.net/
http://www.movie-forumz.org/
http://www.movieforumz.com/
http://www.megavideo.com

Lot for sale in the phillipines

2009-12-04T07:39:00.000-08:00

A 34,600 square meter lot is for sale in just 100 php per square meter( $2.12 per square meter).

LOT PRICE LIST
Unit	Equivalent	Total Amount of the lot
PHP	100 Pesos per square meter	3, 460, 000 PHP
USD	2.12 USD per square meter	73, 352 USD

Located at Malhiao, Badian, Cebu Philippines. A southern part of Cebu.

It is not far from the road, not far from the sea and has a good view up.

A small cave is located on the middle of it.

A perfect place for building rest house for the family. It is good for subdivision and can be negotiable.

If you are interested about the lot you can email the blog admin

mlemar.12@gmail.com or contact this number : +639224786707

BELOW ARE THE PHOTO OF THE LOT :

Cellphone Repair Notes; Tips and Tricks

2009-12-04T07:34:00.000-08:00

Cellphone Repair Notes; Tips and Tricks

· Check charger if it has 5V-9V

· Check battery pack

· Check battery terminal

· Check charging pin

· Check fuse

· Check inductor coil & charging protector diode

· Check charging IC

· Check power IC/UEM

INSERT SIM

• Check SIM card

• Check SIM terminal/connector

• Check transistor, resistor, capacitor (DTC3)

• Check SIM protector IC (DCT4)

• Check power IC/UEM

NO DISPLAY

• Check rubber or metal connector

• Check LCD

• Check transistor, resistor, capacitor (DTC3)

• Check LCD protector IC (DCT4)

• Check flash / RAM IC

• Check CPU

KEYPAD MALFUNCTION

• Check keypad tips

• Check for dirt

• Check for open pattern in each row/column

• Check keypad protector diode

• Check CPU

NO EARPIECE/SPEAKER

• Check cell phone volume

• Check speaker (connected to speaker board interface)

• Lift the speaker connector

• Clean if necessary

• Check each resistor, capacitor, inductor

• Check audio IC/UEM

MICROPHONE

• Check cell phone volume of the microphone

• Check microphone (connected to mic board interface)

• Lift the mic connector

• Clean if necessary

• Check each resistor, capacitor & inductor

• Check audio IC / UEM

•

NO RINGTONE

• Check cell phone volume of the ringtone

• Check buzzer (connected to buzzer board interface)

• Lift the buzzer connector

• Clean if necessary

• Check for open pattern (lifted pads) from buzzer interface

• Check inductor coil (DCT3)

• Check UI IC /UEM

LOW RINGTONE

• Check cell phone volume of the ringtone

• Check buzzer

• Replace

SLOW RINGTONE

• Check 32.468 kHz crystal oscillator

• Check flash IC

NO VIBRA-MOTOR

• Check cell phone settings for vibration

• Check vibra (connected to vibra board interface)

• Lift the vibra connector

• Clean if necessary

• Check for open pattern from vibra interface (-)

• Board interface to UI IC

• Pin # 16 (-)

• Pin # 1 (+)

• Check UI IC

NO SIGNAL

• Check internal antenna connected to antenna board interface

• Check flash program c/o computer

• Check antenna switch

• Check PA

• Check filters

• Check RF IC & 26 mHz crystal oscillator

• Check audio IC

• Check VCO

• Check power IC

• Check CPU

SIGNAL SETTINGS

Phone settings

Ø Network selection

Ø If no network found

Ø RF IC & 26mHz crystal osdcillator

Ø Audio IC

Ø VCO

Ø if network is found e.g.; globe, smart, sun, do not access PA

WATER DAMAGE

• Do not switch on the unit

• Remove battery

• Do not try to charge the unit

• Clean the board using board cleaner

• Dip the board to the ultrasonic solution

• Troubleshoot

• Test battery board interface

• If shortage:

• Check all capacitors & diode

• Pull-out charging IC (test battery terminal)

• Pull-out UI IC (test battery terminal)

• Pull-out PA (test battery terminal)

• Pull-out power IC (test battery terminal)

CONTACT SERVICE

• Check flash program c/o computer

• Reasons for CS

• Cobbha parallel test failed – audio IC

• Ccont parallel test failed – power IC

• Bad IMEI data - change IEMI number

• MCC PPM check failed - flash program

• EEPROM check failed - eeprom IC

• Flash

HANGUP/AUTO SHUT-OFF

• Check flash program c/o computer

• Check flash IC

• Check audio IC

• Check power IC

• Check CPU

NO POWER

• Check battery pack

• Check battery terminal

• Check power switch

• Check flash program c/o computer

• Check capacitors & diodes

• Check power IC

• Check RF IC & 26mHz crystal oscillator

• Check flash IC / RAM IC

• Check CPU

FLASH RESULTS

DCT 3

• Phone ram is bad - RAM IC

• Unknown flash - flash IC

• Rootsrap begin - power IC

• Reloader err - power IC

• Flash sending loader - flash IC

• Done - RF IC

DCT 4

• 1st boot ok, 2nd boot err - flash IC

• 1st boot err, process failed - flash IC

• 1st boot err, bad resp - can’t conn. UEM

• 1st boot err, bad resp upp - can’t conn CPU

• 1st boot ok, full factory defaults failed - UEM

• 1st boot ok, flash id failed - flash IC

• 1st boot ok, flash complete - good

Cellphone repair Tips : Water Damage

2009-12-04T07:31:00.000-08:00

WATER DAMAGE

TIPS :

1.DO NOT SWITCH ON THE UNIT
2.REMOVE THE BATTERY
3.DO NOT TRY TO CHARGE THE UNIT
4.CLEAN THE BOARD USING BOARD CLEANER
5.DIP THE BOARD INTO THE ULTRASONIC SOLUTION
6.TROUBLESHOOT
7.TEST THE BATTERY TERMINAL ON THE BOARD
1. IF IT IS SHORTAGE.

Fire Drill In my school Seminar

2009-12-04T07:23:00.000-08:00

Friday 7 , 2008 the Cebu City Fire Marshall officers implement a fire drill in CITE through sharing their experiences as a fireman , Share techniques on how to save life and how to secure yourself in times of emergency .They also shared some tips on how to make an area safe . They said that putting metal braces to windows, padlocks to any exit doors can be sources of entrapment , the officer said that as an individual we must be aware of this matter like being concern on what is happening ,we should know what is safe or not “think first before doing” and don’t panic during emergency, don’t let an irrational behavior eat you in times of emergency .

Very important Tips to Communicate well during emergency :

•Make sure you provide complete details of what you are reporting to the authorities during emergency like questions that begins with : when , where , how , why , what :
•And you must know the appropriate Emergency numbers to be dialled in case of emergency.

Here are some common trap areas during fire :

Comfort room the comfort room is probably the unsafest area during fire because it is enclosed properly where once you get in you can’t get out.

Solution : I suggest to make a window that allows a person to exit on it easily in case of fire.

Dead – end “ grilled windows and fire exits that are lock.

Some Tips on How to save yours and others life

•Assuming that your house is on fire and you are inside. It is full of smoke and you could not see anything, one thing that you need to do is to crawl , so you are not going to collapse due to reduce oxygen level, crawling is done to acquire oxygen in order to survive: remember that the smoke is one foot away from the floor : so if want to rescue your relatives or people inside, you must crawl in order to survive.
•You must have an active mind or have a presence of mind
•You must know how to apply first aid to your patient when doctor is not yet around.
•Tying a rope when rescuing a patient that is in a high place is a great technique that you should practice and know.
•Know the behavior of fire, classes of fires and how to put off different classes o fire.
•As a student or employee or any other people must know where is the exit in times of emergency , they must know the routes and passages of the building where they live or work.
•You must know where to find the fire fighting equipments.
•You must know the kind of fire extinguisher should be used in different

kinds of fire :

•Knowledge on how to use fire extinguisher is a must.

Follow the steps below :

◦Pull the pin.
◦Aim the nozzle at the based of the fire and keep a distance of 3 feet away from the fire and that you are in the same direction with the wind , you can determine it through the smoke.
◦Squeeze the lever slowly : This will release the extinguishing agent in the extinguisher. If the handle is released, the discharging stops.
◦Sweep from side to side. Using a sweeping motion, move the fire extinguisher back and forth until the fire is completely out. Operate the extinguisher from a safe distance, several feet away, and then move towards the fire once it starts to diminish. Be sure to read the instructions on your fire extinguisher label – different fire extinguishers recommends operating certain distances. Remember: Aim at the base of the fire, not on the flame!

Note : We are the one responsible during emergency.

Cebu City Fire Departments Emergency Numbers

2009-12-04T07:13:00.001-08:00

As our day becoming more and more prone to Technology, even cell phones have an internet connection, that give a big help to us .So I think that posting some important thing on the internet would be a great help in order for them to browse in case of emergency.

Connecting all department of Cebu City Fire team for quick assistance in case of emergency.

Cebu City Fire Departments Emergency Numbers

First Aid in Repairing Cellphone - No ringtones

2009-12-04T04:48:00.000-08:00

In human there's what we called first aid, What if we apply it in some electronics gadgets and devices. The purpose for this, is to save some useless repair expenses because of a very little malfunction on the devices that can fix easily even you don't know more about the thing.

Category: Cellphone Problems

No ringtones.

Prequisite's:

Torque screw driver ( that is totally fit on the screw but the common among cellphone is the T6 screw driver)

1. Dis assemble and assemble your cellphone then clean the internal part especially the connections between the faulty part, and check if the devices working now properly.
2.locate the Speaker then pull it out, go to cell store near you and buy a new one.
3.then if the problem still exist, it's time to go to the repair personnel.

No paper jammed but the printer display paper jammed.

2009-12-04T04:41:00.001-08:00

No paper jammed but the printer display paper jammed.

! This is a hardware problem because the sensor that sense the paper if has been mis aligned.
the sensor always saw and detect or in other words, it has been triggered...

Possible Solution:

1. Reset your printer by unplug and plug the power cord.
2.If you know how to disassemble the printer, then do it.
3.Clean the paper path to make sure there's no little pieces of paper sense by the sensor.
4.Check the paper pick mechanism if it is working properly.

How to get the paper stuck inside the printer.

2009-12-04T04:39:00.000-08:00

Printer jam problems.

How to get the paper stuck inside the printer.

caution: pls turn off the printer before performing the steps.

1. check if the printer have a backdoor. if yes, you can easily get the paper stuck in the paper path.
2. if the paper was hard to pull use twizzer to get the paper.
3.Or make the paper wet a little order to get rid easily.

How to Install a printer without a driver disc.

2009-12-04T04:35:00.000-08:00

How to Install a printer without a driver disc.

1. Define the model and brand of the printer.
2. goto to your product manufacturer website.
3. search your printer model driver.
4.then download it, don't worry if you pick up the wrong driver, anyway you can uninstall if you want.
5.Run the software and just follow the wizard.