Trace the contour of the hammerhead for reference on a piece of paper. Make a tracing of both axes of the curve. Take measurements with a caliper if you desire total control over replicating the hammer face prior to the ding.

File down to the deepest depth of the offending mark with a #3 or #2 hand file. Preserve the contour of the hammer face prior to the ding by comparing it to the tracings and measurements you made.

When the mark is filed down and the face profile of the hammer is to your liking, proceed through several grades of sandpaper from coarse to fine until the steel is absolutely smooth and scratch free.

Buff the hammerhead on a polishing arbor with Fabulustre compound until it is polished to a mirror finish. Remove excess compound with a lint-free cloth. Hide the hammer, so no one will ever use it for home repair again.

Ending a beaded bracelet with a crimp bead or tube can be trying.  If you squeeze it too hard, the crimp just breaks and you have to start again.  If you don’t squeeze it enough, the string just comes out and all the beads fall off. This is an easy “how to” use a crimp tube correctly.

Place a crimp bead (tube) at the end of your beading wire or string and push down about 2 1/2-3 inches…this leaves about 3 inches of string to finish off.  (You can adjust to less as you get more proficient).  Thread the clasp of the through the string to meet the crimp. Fold the string around the clasp and lace through the crimp so now you have both ends of the string or wire through the crimp. (one short one and the long one that has the bracelet or necklace beads on)

With your crimp tool, squeeze the crimp bead, gently but firmly, with the first hole at the nose of the tool.  Then move to the second hole and squeeze again.  The crimp bead should now be bent in the middle.  That’s it! You did it! Repeat on the other side with the other half of the clasp! 

Use a crimp cover bead over the folded crimp tube for a more refined look! A Crimp Cover Bead is a special silver or gold bead that is “open”. Place it over the crimp tube and gently close it around the tube with the first hole toward the nose of the pliers. It takes a little practice but it will close and look exactly like a bead.

You can also use a bead with a hole large enough to fit over the crimp tube to cover up the tube.  Try this a few times and you will come out with a perfect crimp every time!

We’re set up on the Southwest corner of the show…look for the Big Gray Prevost Bus

and our OdorZout trailer.

Jan. 2nd Open from 6-10 pm First Friday at Tilt Gallery in Downtown Phoenix.  For directions: Visit www.tiltgallery.com.  Come and visit while looking at great photography and art from LOCAL ARTISTS.  Friendly people, relax and stay a while!

Jan. 9-11, 9-5 pm Flagg Gem and Mineral Show:  Mesa Community College. Look for the big gray Prevost Bus!  For you gem and mineral collectors and rockhounds, a nice small show with great vendors.  Google Mesa Community College for directions to the campus.  Oldest running show in the valley for Gems and Minerals.

Feb 8th 11-4 Art Fair for Valentines Day at Kathy Metcalfs.   Mapquest 1221 E. Winged Foot Rd, Phoenix, 85022. for directions.  Lots of great artists will be there, plus Tarot Readings, Angel Readings, and discount prices on Astrological Compatiblity charts.  See www.katherinemetcalf.com to make appts for readings. Relaxed atmosphere and lots of fun.

Feb 14th 10-4   Angels Serenity Art Walk located on the southeast corner of Tatum and Greenway, between Safeway and Walgreens.  Come and shop with local artists, visit the store.  They usually have great musicians playing while you shop.  Come and hang out in a casual atmosphere for a great time.

Although it may look like something easy to make, it takes a lot of practice and knowledge to put the pieces together.  Most of the Dichroic jewelry you see has anywhere from 2-4 layers of glass, but may have even more. 

You must pick the layers carefully; color, textures, surface of the glass, types of glass must be compatible, and chosen to co-exist to form a beautiful finished product.  Carefully cut by hand and then layered together, they await to be fused (melted) together in a kiln.

The glass is carefully fused together in a kiln brought up to over 1600 degrees for hours, and then left overnight to cool.  If done correctly, pendants made of fused glass may be made into stunning pendants, earrings, rings, etc.  It can also be made into larger plates, trays or dishes by designing pieces of Dichroic glass into other types of glass.  Once again, adding sparkle to a eye-catching piece of art.