Husqvarna Viking Service and Repair

Husqvarna forum and FAQ's

2016-09-09T20:52:00.000-07:00

Husqvarna 2000 service and repair

2014-06-23T01:36:00.002-07:00

Husqvarna 2000 service and repair tips. Removing covers, sewing foot repair and general repair tips

The needle position not aligning could be because your machine needs a good clean and oiling. I’m not sure if your model have a button hole function. Make sure it is not engaged. Sometimes the shaft where the reverse unit turns in get sticky and does not return with your button hole dial. You will have to oil and warm it up with a hair dryer or use a special release oil. You will get access to it by removing the side cover. It can take a while to work in the fresh oil.

Husqvarna 2000 service and repair

Brother XL-2220 tension problem

2014-05-07T01:25:00.000-07:00

Brother XL-2220 tension problem. I bought the machine second hand, and was warned of potential tension issues, however when I used the machine it ran fine. After a little light sewing (three cotton baby bibs), it suddenly stopped working. By this I mean, the top stich wuold come through fine, but the bottom would just be miles and miles of tangled thread. Under instruction from a seamstress friend I have tried changing the needle, adjusting the tension, and buying a higher quality thread, but unfortunately the problem persists. Do you think this is servicing or repair?

Seems like a normal repair but you can try the following:

Tension Problem

Your top tension is too low and should be on 5.

Make sure you have some tension on the bobbin case.

Make sure no cotton is stuck in-between your top tension plates. (Use a needle to hook it out)

Make sure no cotton is stuck in-between your bobbin case tension plates. (Use a needle to hook it out)

Your bobbin case could be damaged.(Sometimes you can remove the hooks on it)

Double check your threading.

The bobbin case stopper could be loose(Look at the images attached.)

Bobbin case stopper:

Brother XL-2220 tension problem

Husqvarna Viking camstack gear | 610

2014-04-23T04:06:00.002-07:00

Husqvarna Viking camstack gear | 610

Upper tension assembly MO-2052

2014-03-17T03:04:00.002-07:00

Upper tension assembly

Upper tension assembly for some Globe and Kenmore sewing machines are the same. The barrel width is (18mm/11/16″) and a spring that pulls up. The barrel width must be the same to fit into tension unit hole. When you open the light cover you can see the screw holding the upper tension assembly. The upper tension assembly should just pull out when the screw is loosened. Just take not of the tension release pin not to loose it.

Upper tension assembly MO-2052

Make sure not to push the upper tension assembly to deep so that the tension release pin push the tension plates open. You’ll have zero tension then. If it does not go deep enough your tension release won’t function. The presser bar lever can’t push the tension release pin

You can see in the images below from a Globe 510 sewing machine where to find and loosen the screw holding the upper tension assembly.

Upper tension assembly MO-2052

2014-03-16T01:39:00.002-07:00

Husqvarna Viking motor assembly

Husqvarna Viking sewing machine

Check both carbon brushes by removing the brush cap. The carbon brushes should be at least 50% the size of new ones. It is recommended that both the carbon brush and spring be replaced. After installing new carbon brushes dress the commutator to seat the brushes.

The Husqvarna Viking sewing machine motor noise is affected by the load and the belt tension. If the motor deviates from normal check the tension of the cog belt. When replacing carbon brushes it is important to note the model of the machine. Starting with 6460 the carbon brush holder (16) was redesigned. Once the carbon has worn the holder will not allow the carbon brush spring (13) to ride the commutator. When ordering carbon brushes it is best to use the 40 16295-01 from 6460 and later models. For earlier models use the carbon brush 41 14 934-01 which will repel from the commutator automatically when the carbon is worn.

Husqvarna Viking sewing machine motor brushes

Husqvarna Viking sewing machine motor brushes

2014-03-16T01:39:00.000-07:00

Husqvarna Viking motor assembly

Husqvarna Viking sewing machine

Husqvarna viking 2000 sewing machine gear

2014-03-15T17:39:00.000-07:00

Husqvarna Viking Power Gear

The husqvarna viking 2000 sewing machine power gear or lower gear or gearshift is a practical future to lower the sewing machine speed. This video will show you how it operate and solve some basic problems

Husqvarna Viking 2000 sewing machine

Materials used making the Husqvarna Viking 2000 sewing machine and power gear

Most of the small details (parts) of the sewing machine are made of steel or steel alloys with different grades of tempering. However, quite a lot of the details in the mechanisms are made of die-cast aluminum. In addition, here are some details which must have good bearing properties and wear resistance, which are made of different sorts of plastic. On the subject of plastic, it is important to distinguish between the type of plastic used in design details and the type used for inexpensive packing and throw-away wrappings. The constructional plastics have completely different properties and are considerably more expensive. If a detail, e.g., a cog wheel or a programmer, is made of plastic, it must have advantages over metal – e.g., a cog gear will function more smoothly 20 and quietly; a cog gear or programmer will have more wear resistance. If the Husqvarna viking 2000 sewing machine power gear is made of metal it will wear much quicker, even when using the best special steel, as long as the properties are not changed completely by means of an 0il bath or the like. You can find the Husqvarna Viking Technical Manual at this link.

I’ve add more related videos on how to repair your Husqvarna Viking 2000 sewing machine.

Husqvarna viking 2000 sewing machine gear

Singer air foot control repair

2014-03-11T16:49:00.002-07:00

For Singer models: 4610, 4611, 4613, 4617, 4623, 5932N503, 6230, 6233, 6234, 6235, 6244, 6267, 6268,,7000, 7004, 7005, 7011, 7015, 7028, 7033, 7035, 7037, 7043, 7050, 7060, 9110, 9113, 9117, 9124,,9130, 9133, 9134, 9137, 9143, 9210, 9217, 9224, 9240, 9410, 9416, 9417, 9430, 9444

Singer air foot control repair:

You can open the slideshow and get the full Singer air foot control repair tips with the pictures. I’ve repaired many Elna and Singer air foot controls with this easy repair and it saves you buying a new foot control or parts.

Singer air foot control repair

Overlocker looper timing gear 11226

2014-03-10T17:07:00.002-07:00

: Looper Gear 11226

: Looper Gear 11226 cracked

: Frister Lock 3

: Globe M3 Overlocker

Overlocker looper timing gear 11226

You can buy the gear from the sites listed below. The Frister Rossmann, Globe and White overlocker are mostly the same machines and use the same parts, gears, blades, looper etc.

Globe looper timing gear 11226 from New Zealand

Globe overlockers

White looper timing gear 11226 from the States

Compatible with White Serger Models:

503, 504, 523 & 534 (Old Style)

Very Old Fritser and Rossmann models

Overlocker looper timing gear 11226

Elna air electronic foot control repair and parts

2014-03-04T16:06:00.002-08:00

Elna Air Electronic Foot Control

Membrane 436410-10

Elna Air Electronic Foot Control parts list

Elna Hose Head436410-H

Hose 988667-003

Membrane holding plate

New Elna air electronic foot control

You can by a new complete Elna air foot control from this link: Elna air electronic foot control in New Zealand. The other parts are available on request and can be found be widely on the internet. You can also by a complete foot control from the links below. This foot control and parts are compatible with the Elna Sewing Machine Models: Air Electronic 38, 39, 58, 59, 68, 69, Carina Jubilee 45, 46, 55, 56, 65, 66, 500, Lotus 22, Stella 17, 27, 37, 57, SU.

Repairing a faulty Elna air electronic foot control:

I’ve set out the following faults that can be checked before buying a new foot control. The easiest way of finding these faults are to dip it in water, close off the foot control head and apply pressure on the air control membrane to see where the air bubbles escape. This should give you a good indication where the foot control is leaking air.

Finding and repairing the leak

Foot control hose 988667-003: The Elna foot control Hose 988667-003 can get a hole or cut. You can always cut out the damaged part of the hose and providing it is still long enough use the narrow plastic ink tube of a empty ballpoint pen to join it.

Membrane 436410-10: It is not worth trying to repair the Membrane 436410-10

Elna hose head 436410-H: Elna Hose Head 436410-H can get little cracks and won’t seal anymore

Membrane holding plate: Membrane holding plate gets cracked from age or when the four holding screws are tightened to hard. You will get a leek between the membrane and the holding plate

Elna hose head 436410-H: You can easily repair your hose in the same manner as the Singer Foot control below

It can be easily repaired using the inner tube of a old ballpoint ink pen

Cut a piece of tube for connecting the hoses

Insert the plastic tube halfway into the hose

Elna air electronic foot control repair and parts

Elna bobbin case repair for Stella TSP

2014-03-04T14:27:00.002-08:00

The spring scale N° 101’670 is calibrated at the factory and should not be modified.

Referring to the first picture in the picture gallery below on how to set the tension on the lower bobbin case:

1. Insert a full bobbin of embroidery thread N° 30-2 ply (60-2) and thread the tension as per drawing. Set the take-up lever in its highest position.

2. Set gratuated wheel “C” on “1″, loosen screw “a” and adjust eccentric “b” to obtain a residual tension between 45 and 55 g by pulling the spring scale 1011670 slowly in the illustrated direction.

3. Tighten screw “a” whilst retaining “b” in its position.

4. Turn graduated wheel “c” several times between “0″ and “2″ and recheck adjustment .

Elna bobbin case repair

Elna bobbin case repair questions can be asked in the comment box at the bottom of the page.

Elna bobbin case repair for Stella TSP

Globe foot controls

2014-03-03T22:48:00.002-08:00

: Foot control plug

: Globe foot control plug

: Globe Cub 3 plug

: Globe M3 Overlocker

: Frister Lock 3

: Globe 510 plug

Globe Foot Controls

The globe sewing machines and overlockers use mostly the same plug except for some of the electronic models. This three hole plug were also used by various other sewing machine and overlocker brands like Husqvarna, Janome, Pfaff, Singer, Jaquar, Toyota, Frister & Rossmann, White and more. I’ve listed some of the models that should also fit the Globe foot controls below.

Compatible part numbers are: YC-482E, 40059964, 72917, 1150018-834, YC-482T-1, 412000018, 11939, 11850E, 30990 and 11850.

Many models of sewing machines and overlockers used for the Globe, Frister & Rossmann and White brands are the same. The model numbers may be different but the parts are mostly interchangeable like the foot controls, gears, baldes, loopers etc.

Husqvarna: 340D-341D-905-910-3400
Janome: 5500-8000-8600-8800
Pfaff: 4240-4250-4260
Singer: 14J334-132-1019-1025-1027-132Q140Q
Toyota: 4300-4600
White: 208-503-505-710-734-834D999-1523-1577-1599-1800-1934D-19554040-4075-5500-534D-7234-734D-7347934-7934DW-2000-SL243D-SL34

You can always find a matching foot control from Trademe foot controls in New Zealand or Dulwich Hill Sewing Centre in Australia and they should all be 240V.

The following foot controls are for a 110v power supply and won’t be safe with a 220V power supply.

Globe foot controls

Brother foot controls for their sewing machines

2014-03-02T14:54:00.002-08:00

: Brother Foot Control

: Brother PS-53 foot control

: Brother VX800 plug for foot control

: Brother Electronic Compal Star 732

: Brother Foot Control Plug

: Brother Foot Control Plug

Brother foot controls

The following models are compatible and their foot controls should fit the same plug for all the models. The best is to view the machine plug on your machine and to see if it matches your sewing machine, overlocker or serger. At the bottom of the page I added some links to various Brother foot controls.

Always check electrical rating of the Brother foot controls and sewing machines. The American 110V won’t be safe to use on a 220V power supply!

You can search for free manuals from my Brother Manual Search Page

Brother: 461, 1781, LS1217, LS2125, LS2220, PS1000, PS1200, PS1250, PS1700, PS1750, PS1800, PS2200, PS2500, PX100, PX200, PX300, VX540, VX560, VX710, VX808, VX847, VX857, VX870, VX920, VX940, VX950, VX970, VX1010, VX1020, VX1100, VX1120, VX1125, VX1140, VX1250, VX1400, VX1500, XL2010, XL2015, XL2021, XL2022, XL2027, XL2030, XL3010, XL3022, XL3027, XL3030, XL3100, XL3200, XL4010, XL4011, XL4012, XL4014, XL4015, XL20, XL4030, XL4040, XL4050, XL4060, XL5010, XL5011, XL5020, XL5021, XL5030, XL5031, XL5130, XL5232, XL5300, XL5340, XL55, XL56, XL5500, XL5600, XL5700, XL6040, XL6050, XL6060, XL6452, XL6562, XL634D, XR16, XR23, XR31, XR33, XR34, XR35, XR37, XR40, XR46, XR52, XR65, XR65T and LS series, VX series, XL series, XR series, Galaxy 8015, Riviera 1681, Sonata 6621.

Most Brother serger model: 350, 360, 451, 461, 523N, 524N, 525N, 526, 526D, 546, 546D, 626D, 634D, 640D, 661, 681, 730DE, 741, 751, 760DE, 834DP, 920D, 925D, 929D, 934D, 935D, 1034D, 1681, 1781, 2340CV, 3034D, 7029,626, 634D, 1034D, M526LCW, 900 series and many others.

Babylock: B17, BL21, BL200, BL702, BL713, BL722, BL1500, BL1550, BL1556, BL2100, BL2200, BL2400, BL2600, BL6000, BL6150, BL6200, BL6300, BL6500

Bernina/Bernette: 50, 75

Simplicity: SL2160, SL8020, SL8130, SL8220, SL9130, SL9150, SL9240

Sonata 6621

Viking Huskylock: 234D, 430, 431, 535D, 600, 700, 800, 650ED, 1000, M530.

Riccar R2050

Brother foot controls for their sewing machines

Singer sewing machine gear replacement for 5805 | 5802 | Melody 40 models

2014-02-25T23:55:00.000-08:00

Singer sewing machine gear replacement

A tip on getting the gear screw undone. Drill a hole in the back that lines up with the screw. It will save you from having to remove the top shaft. If you pull the vertical shaft out you should be able to shift it pass the horizontal top shaft. 353273002

back to album list | Slideshow

	Product	Stock	Price
	P60216 Portable FLATBED Sewing Machine Carry Case for 14.5×7″	In stock	$39.99	Buy product

Singer sewing machine gear replacement for 5805 | 5802 | Melody 40 models

2014-02-25T19:31:00.001-08:00

Bernina 830 Record threading

2014-02-18T00:31:00.002-08:00

Bernina 830 Record threading

Sewing machine troubleshooting guide

2014-02-17T02:37:00.002-08:00

Many users think the machine has broken down when they first experience trouble. This is easily corrected with this sewing machine troubleshooting guide that could save you time, trouble and money.

Simple adjustments the sewer can do

Machine binds, locks or noisy

Upper thread breaking

Lower thread breaking

Needle Breaking

Missing or irregular stitches

Material Puckers

Material will not feed through machine

Bobbin winder will not turn or winds unevenly

Electric motor fails to operate

Machine binds, locks or noisy.

Probable Cause

Thread or lint caught in race. Possible machine run without sewing fabrics

Bobbin case inserted incorrectly

Feed or darning indicator wrongly set

Lack of oil

Remedy

Many users think the machine has broken down when they first experience a “cotton jam”. This is easily corrected. Turn to the section of your instruction manual which tells you how to remove and clean the shuttle and race. Follow directions carefully and when you have removed the shuttle. Thoroughly clean the race (into which shuttle fits), the race cover and the shuttle itself. Be careful not to score or damage the shuttle or race these are precision-ground parts. Before re-assembling put one spot of oil on your finger-tip and rub this around the outer edge of the shuttle. Do not over oil. Now refit shuttle and race cover as described in your instruction book

Refit bobbin case as shown in instruction book

Set these as described in your book>

Oil as advised in instruction book

Upper thread breaking content goes here.

Probable Cause

Machine wrongly threaded

Tension too tight

Needle Wrongly fitted

Bent or damaged needle

Using wrong thread

Thread wound around spool pin!

Remedy

Refer to threading instructions in

your instruction book

Turn tension knob left to loosen

upper tension

Your instruction book will tell you

how to fit the needle properly

Replace with new needle

Refer to needle and thread chart in

instruction book

Release thread from spool pin

Lower thread breaking content goes here.

Probable Cause

Bobbin wound unevenly

Too much thread on bobbin

Bobbin case wrongly threaded

Bobbin case tension too tight

Bobbin bent

Remedy

Remove thread and rewind evenly

Remove excess thread

Refer to threading diagram in

instruction book

Rarely needs adjusting-but refer

to tension instructions

Replace bobbin

Needle Breaking content goes here.

Probable Cause

Bent or damaged needle

Material too thick for needle

Pulling material

Machine set to zig-zag when using straight stitch foot and needle plate (Refers to swing needle machines only)

Pattern cams left in machine (Refers to swing needle machines only)

Swing lever (zig-zag) moving while needle in work (bending needle) (Refers to swing needle machines only)

Needle not pushed up to stop screw in needle bar (Make sure the needle is deep enough)

Remedy

Fit new needle

Refer to needle and thread chart

Never pull material when sewing, just guide it

Ensure swing lever (zig-zag) set for straight sewing

Remove pattern cams from machine

Ensure needle clear of work or pressure foot raised when using swing (zig-zag) lever

Loosen needle clamp, push needle up to stop screw and make sure not dirt is trapped

Missing or irregular stitches content goes here.

Probable Cause

Needle wrongly fitted

Using wrong needle or thread

Top tension slack

Machine wrongly threaded

Bobbin wound unevenly

Feed dog too low

Insufficient pressure on presser foot

Pattern cams left in machine (Refers to swing needle machines only)

Remedy

See instruction book, fit correctly

Refer to needle and thread chart

Increase tension

Thread correctly. See instruction book

Rewind bobbin

Raise feed. See instruction book

Increase pressure. See instruction book

Remove pattern cams from machine

Material Puckers.

Probable Cause

Tension too tight

Stitch length too long

Bent or blunt needle

Thread too thick

Remedy

Loosen. See instruction book

Reduce stitch length

Fit new needle

Refer to needle and thread chart

Material will not feed through machine.

Probable Cause

Feed set to “‘Darn”

Fabric indicator set to “‘Darn”

Darner released (upper position)

Remedy

Set to “Normal”

Set to correct type of material

Engage darner (lower position press down)

Bobbin winder will not turn or winds unevenly.

Probable Cause

Oil on pulley rubber (slipping)

Cotton wound around spindle

Remedy

Remove oil with clean cloth

Remove cotton from spindle

Electric motor fails to operate.

Probable Cause

Fused plug

Faulty connections

Remedy

Check fuses

Have connections checked by a qualified electrical worker

Sewing machine troubleshooting guide

Husqvarna 2000 service and repair

2014-02-08T00:15:00.002-08:00

Husqvarna 2000 service and repair tips. Removing covers, sewing foot repair and general repair tips

The needle position not aligning could be because your machine needs a good clean and oiling. I’m not sure if your model have a button hole function. Make sure it is not engaged. Sometimes the shaft where the reverse unit turns in get sticky and does not return with your button hole dial. You will have to oil and warm it up with a hair dryer or use a special release oil. You will get access to it by removing the side cover. It can take a while to work in the fresh oil.

Husqvarna 2000 service and repair

back to album list | Slideshow

Husqvarna 2000 service and repair

2014-02-06T22:38:00.001-08:00

Absolute Sewing Flyer

2014-02-05T16:03:00.002-08:00

Absolute Sewing Flyer

The new Absolute Sewing flyer for sewing and material shops on Hastings, Hawkes Bay, New Zealand

Absolute Sewing flyer

Service and Repair

Sewing machine services from: $70

Overlocker services from: $80

Sharpening of scissors $8

Sharpening of garden shears $10

Overlocker looper replacements

Gear replacements

Repairs to all makes & models

Most work done in two days!

Tel: (06) 876 4266 Cell:021 296 1762

www.absolutesewing.co.nz (Web)

www.sewingnz.org (Support)

www.sewingnz.com (Shop)

Absolute Sewing Flyer

Husqvarna Viking Zig Zag timing

2014-02-04T22:40:00.002-08:00

I have replaced the cam and now when I try and do a zig zag pattern the timing is out and the needle starts to zig or zag whilst it is still performing a stitch.

I’ve added two images explaining how to set the Husqvarna Viking zig zag timing, the worm wheel tolerance and a extra diagram for the principle of zigzag synchronisation. This should guide you through the process, else you can always ask a question on the comments box at the bottom of the page.

: Timing The Zig Zag Movement

: Worm Wheel Tolerance

: Zigzag Synchronisation

: Husqvarna Viking cam stack gear

Husqvarna Viking Zig Zag timing

The general rule for setting the zig zag timing on any sewing machine is as follow, but also apply to setting the Husqvarna Viking zig zag timing:

Set stitch width control at maximum width position. Turn the handwheel, observing that the needle goes straight up with now side movement to a point 2-3 mm above the needle plate. At this point the needle should begin to swing over to the other side. Verify that the needle goes straight down the other side.

If adjustment is necessary, loosen screws on worm gear and turn slightly in either direction.

Sometimes the worm gear can get sticky and won’t move freely. You can warm the worm gear with a hair dryer to loosen the old oil. Applying excessive heat can damage plastic parts of your machine

You can buy the full manual or cam stack gear at these links Husqvarna Technical Manual and the cam stack gear here

Husqvarna Viking Zig Zag timing

Husqvarna Viking 2000 replacement walking foot

2012-09-24T01:29:00.000-07:00

A generic foot that fits and align on your Older Husqvarna Viking sewing machines. I've added some pictures and little clip where the machine is running at full speed. The Part number is P60444

Low shank walking foot - Absolute Sewing Store:

Husqvarna Viking Practica III sewing machine stuck in reverse

2012-09-05T15:24:00.001-07:00

Husqvarna Viking Practica III sewing machine stuck in reverse

As you can see in picture 6 and 7, the button for going backwards is always pushed, I have to take the big button off to be able to pull the brown button in the center and in this position, the machine is going forward, that is to say that the fabric is going from the inside to the outside of the needle. If it is a problem of oil, if there a recommended brand or is any oil forsewing machine is ok? The problem is that the machine is only goig backwards, I should push a buttn to go backwards but the button is blocked.

The unit must be cleaned. If you push the reverse button in and out you will see it work. You might have to use your hand to push the reverse button out from the back. I'll attach a video at the bottom that will explain it better.

butchwax » Blog Archive » Viking 6030 sewing machine rebuild

2012-04-25T18:16:00.001-07:00

butchwax » Blog Archive » Viking 6030 sewing machine rebuild:

Husqvarna Viking Service and Repair

Husqvarna forum and FAQ's

Husqvarna 2000 service and repair

Husqvarna 2000 service and repair

Brother XL-2220 tension problem

Tension Problem

Husqvarna Viking camstack gear | 610

Upper tension assembly MO-2052

Upper tension assembly

Upper tension assembly MO-2052

Husqvarna Viking sewing machine

Husqvarna Viking sewing machine motor brushes

Husqvarna Viking sewing machine

Husqvarna viking 2000 sewing machine gear

Husqvarna Viking 2000 sewing machine

Materials used making the Husqvarna Viking 2000 sewing machine and power gear

Singer air foot control repair

Singer air foot control repair:

Overlocker looper timing gear 11226

Overlocker looper timing gear 11226

Elna air electronic foot control repair and parts

New Elna air electronic foot control

Repairing a faulty Elna air electronic foot control:

Elna bobbin case repair for Stella TSP

Elna bobbin case repair

Globe foot controls

Globe Foot Controls

Brother foot controls for their sewing machines

Brother foot controls

Singer sewing machine gear replacement for 5805 | 5802 | Melody 40 models

Singer sewing machine gear replacement

P60216 Portable FLATBED Sewing Machine Carry Case for 14.5×7″

Bernina 830 Record threading

Bernina 830 Record threading

Sewing machine troubleshooting guide

Simple adjustments the sewer can do

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Probable Cause

Remedy

Husqvarna 2000 service and repair

Husqvarna 2000 service and repair

Absolute Sewing Flyer

Absolute Sewing flyer

Service and Repair

Husqvarna Viking Zig Zag timing

Husqvarna Viking Zig Zag timing

Husqvarna Viking 2000 replacement walking foot

Husqvarna Viking Practica III sewing machine stuck in reverse

Husqvarna Viking Practica III sewing machine stuck in reverse

butchwax » Blog Archive » Viking 6030 sewing machine rebuild