I dared to dream

Trip to Cape Canaveral

2016-08-21T14:03:00.002-07:00

Amazing experience visiting the cape canaveral museum....

On the way to Italy

2016-08-21T13:24:00.000-07:00

Space Shuttle endeavour over flight over san francisco

2016-08-21T13:13:00.003-07:00

Pictures taken in Moffett airfield, CA and in SFO downtown

787 in San Jose, CA

2016-08-21T12:52:00.002-07:00

Jan 2013

Bay tour on memorial day

2012-09-12T08:37:00.001-07:00

Went out for a bay tour with some friends on a C172....wonderful day....little bumpy at places.....and clouds here and there over the bay....our trip took us from RHV, SJC, Moffet, SFO to downtown SFO, bay bridge, golden gate and return via half moon bay....wonderful trip....had to jump over the clouds few times.....overall nice....
pretty busy for the day....many aircraft in the air, it took time to get a flight following from NORCAL and clearance for Class C and Class B

@3500 ft

Mid field San Jose Airport

I-280 on the left

SFO airport runway 29L (United 747 taking off)

United 747 passed below at 2000 ft

SFO International airport

SFO Downtown with Alcatraz

SFO Piers

Another view of downtown with Alcatraz

South SFO

half moon bay

Coastline

Golden Gate in sight

Half moon bay with coastline

My scary emergency moments and how I dealt with it

2012-05-11T08:57:00.000-07:00

Okay friends....lets accept it, flying is fun but brings in lots of challenges & risk as well.....lot of things can go wrong.....however that's what training is all about.....
During my training I got my share of 'oops' moment......and today I would share that with you and the action I took. We all know what needs to be done as taught in our training, but I wanted to share my thoughts about it. Though no one of them resulted in any incident or accident, but did taught me a valuable lessons....hopefully it will teach you something as well....I do wish that you don't encounter any of this situation.....ever

Carburetor ice (carb ice) -- It happened in the chilly month of December, I was flying with my instructor and we were going to KKIC from KRHV for a cross country tour in C152 (we were in touch with NORCAL). I was working on my private. The weather in CA during that month is cold (though not as cold as east coast but its cold). We were cruising at 6500 MSL with 2200rpm. The outside temperature was around 1 degree Celsius. Around Salinas suddenly we noticed a drop in RPM by about 200 rpm i.e. to 2000 rpm. I felt & heard it immediately, however it stabilized at 2000rpm. Since till this point I had just read about carb ice and never actually encountered it. I told my instructor who was busy in his mobile. And he immediately suggested to put full throttle and mixture & also turn on the carb heat. Then while carb heat did its job he said climb higher, just in case we loose engine, the cushion of altitude will give us some chance to plan. I did question him that since climbing higher meaning lower temp and increasing the carb ice issue. But he said its a trade off...since the carb heat is doing its job, you expect to get some relief but in case it doesn't then you have the luxury of altitude to plan your descent. Other action we took was instead of proceeding ahead we started circling above salinas just in case we need to land. Norcal noticed that and gave us a call. We informed them of the situation and told them that so far we are taking precautionary steps. Slowly the rpm started climbing up & returned normal and we decided not to proceed ahead as we knew that temperature over KIC was even low, so chances are still there. anyway long story short, we informed norcal about our decision to head back. Kept the carb heat partially on for a while and returned safely. Lessons learned: Anticipate carb ice in cold conditions. Keep an eye & ear on the engine and take action immediately by putting full throttle, mixture and carb heat. After that try to gain altitude if possible. Couple of days later I went solo and returned without any issues...Happy flying....

Son of a gun, its a plane -- Well this was exactly what my instructor said when some daredevil aerobatic aircraft zoomed passed us. This happened when we were practicing steep turn in a C152 before my checkride near KCVH - Hollister. I always had issues with steep turn but on this occasion I was doing good. In between half 3/4 th of the turn on left side I suddenly see an aircraft zooming past from right to left by about 100ft or less. My instructor also saw it and said "son of a gun, its a plane" Immediately I stopped the steep turn and gently pointed my nose down to descend. However we could not catch any glimpse of the tail number or type of aircraft but my instructor thought it appeared as an aerobatic aircraft. Jeez, that was scary......anyway we were done and my instructor was happy with whatever steep turn I had done we returned. Lessons learned: Well scanning before performing any maneuvers is very important. However if a daredevil is hell bent, I don't think you can do much more than just swear. have a safe flight......

Low voltage in Battery -- This happened in the month of June when I was flying with my instructor in C172 for instrument rating. Our flight was take off from KRHV, make VOR-A approach to Oakdale, GPS approach into Tracy and then ILS into livermore. The approach to Oakdale was successful and I landed. Immediately put full throttle, flaps up and started our takeoff. However as soon as were airborne, I noticed the electrical red light coming up on the low voltage indicator with battery showing towards a -ve side. This was an indication of low battery voltage or in other words the battery is not charging or discharging. Since our engine was running fine and as the alternator, it was okay. The idea was that after takeoff we will follow the missed approach route from oakdale and then contact norcal and ask them to vector us for GPS tracy. Once I informed my instructor, he suggested that lets troubleshoot that problem before we decide to make another approach. We continued to circle the fields next to oakdale to troubleshoot. Initially switch on/off the battery to see if that helps. No it didn't. Then we took the bold move of switching off both alternator and battery (which means the radios will be off). But that also didn't help. At this point we decided to return back to Reid hill view without making further approaches and get it checked. We informed Norcal about our intention and explained the problem. They asked if we needed help and we politely declined. Since engine was running and as the instruments it was okay. On the way back, my instructor pulled out the POH and started looking at emergency procedures. Well it pretty much had the same process of turning on/off. While on the way we decided to conserve the battery. So we informed Norcal that we will go radio blind i.e. will switch off radio and other non essential equipment like GPS (as we knew the valley well to navigate) till we are close to the airport. Norcal suggested that its fine and they will let reid hill know about our situation. And then there was silence for about 30 minutes or so. Till we came close to the mission peak mountain. At that point we switched on the radio and informed norcal. The low voltage was still on. Contacted KRHV, since they knew about the situation, they asked if we need help. We said no and requested landing. Landing was smooth, no incident in putting the flaps down. Thanked KRHV for the help and went straight to the hanger and squawed it. Lessons learned: Keep scanning your instruments for any error. If I had been alone maybe I would have landed in nearby airport and requested help. Since I had my instructor along with me, it was good and I could use his help to troubleshoot.

Pics from my Boston trip

2012-04-15T14:41:00.002-07:00

Taken with my Mobile

Why is temperature dewpoint important

2012-04-09T08:04:00.003-07:00

As a pilot you are responsible for planning and acquiring all information related to the trip. One of the critical information you need to be aware of is temperature dewpoint spread. Let's discuss it in detail:

What is temperature dewpoint -- Simply put it nothing but a temperature, at which the moisture i.e. water vapor in air (or humidity in a volume of air) condenses and appears as liquid, in other words forms cloud. So this parcel of air will need to be cooled to this temperature to form a cloud.
Hence when you gather weather reports, you not only need to know the current prevailing temperature at the airport but also temperature dew point.

The difference between temperature and dew point is known as "temperature dew point spread".

Why we need this information -- This will help pilot get an idea of where the cloud bases are i.e. how high the clouds are possible. Also gives an idea of the likelihood of carburetor ice.

Let's take an example:
Say the temperature at the surface of airport = 14° celsius.
Temperature dewpoint = 5° celsius

Over here what are trying to find out at what altitude is this temperature available so that any water in the air will condense will form cloud.

The formula to be used:
Cloud base in feet = [(temperature in °F - dew point in °F) * 1000]
4.4

hence putting the numbers above:
cloud base in feet = [(57.2 - 41) * 1000)/4.4 = 3681 feet above the surface of airport (add airport elevation to get MSL figures).

What does it mean, if there is enough humidity or moisture in air then expect clouds to form at that that height. This is considering a standard lapse rate. However you should look out for an altitude where this temperature i.e. 5°C is prevailing and will give an idea of cloud base.

Couple of things it helps us identify:

The ceiling at the airport i.e. if you are planning a flight and need to know how high the clouds are.
carburetor ice, so expect to have the possibility of carb ice at that altitude and above. Keep an eye on RPM to see a drop.

Hope this explanation helped.

Why most commercial aircraft do not fly supersonic?

2012-03-15T12:09:00.002-07:00

Why doesn't general commercial aircraft like boeing 747, 737, airbus 320, 380 etc, travel faster than speed of sound i.e. supersonic. They usually travel at 0.87 mach (1 mach = speed of sound). Concorde was the only supersonic commercial aircraft.
Let's explore the physics of it.

credit - http://theboard.byu.edu

From your knowledge of aerodynamics and aerofoil, you know that the upper surface of the wing is curved and lower surface is not. Hence over upper surface the air flows faster as compared to lower (see image above).
Now as aircraft accelerates and nears the supersonic speed, over the upper surface of the wing the airflow (or for that matter any curved surface including canopy, nose etc) can potentially be at supersonic speed. Now at this point a shock wave generates a the point where the supersonic airflow slows down to subsonic. As you can see from the image below, at M=0.77, at the middle, the airflow before it is supersonic and beyond that is subsonic. This results in a shock wave. The airspeed where this shock wave starts appearing is called critical mach number.

credit - wikipedia

This shock wave requires energy and that is supplied by the aircraft itself in form of additional thrust, which means the additional thrust is required to keep the aircraft moving ahead and to compensate the loss of thrust due to shock wave. This acts as a drag and is referred to as wave drag. The engine thrust may not be enough to overcome this drag and move even faster.
Other aspect is that the supersonic speed can cause structural damage.
These two reasons explains why general commercial aircraft does not fly at supersonic speed.
Concorde was able to overcome these 2 design issues and fly supersonic.
Hopefully future air travel will be faster.

Pictures from Bayfont park of SFO Airport

2012-03-12T12:25:00.002-07:00

Took some pics from the bayfront park. Aircrafts landing at 28L/R

Communication in Class B and C

2012-03-09T15:10:00.000-08:00

Communication is very critical while flying but your responsibility increases when you are in the vicinity of Class B or C airspace in US. Let me put some do's and don't about communicating with controller in these airspace.
Read about the airspaces here.

Class B:

Typically large airports (in terms of traffic) are classified as Class B (bravo) e.g. San Francisco, Los Angeles, Washington etc.
Shape of class B appears as upside down wedding cake. Refer the image below.

Credit - Wikipedia

Requirements to fly in Class B are list here: Requirements (pilot certification, equipment etc.)
Communication procedure - You have to be cleared to enter into Class B before you enter the airspace. Most likely you would have to speak with an area controller before you can enter the airspace and may not be directly with the ATC tower of that airport. You should communicate atleast 10 nm in advance. Sample communication with Class B controller

Aircraft Calling: Norcal, Cessna 1234MA at 3500ft over livermore airport, would like to transition through Class B for a bay tour. - Using the standard phraseology of who,where & what. Assuming you are flying through a class C.

Norcal: Aircraft calling standby. -- This means that they have just acknowledged your presence but no permission has been granted yet. KEEP OUT OF AIRSPACE, may have to circle around.

Norcal: Aircraft calling, say your request.

Aircraft Calling: Norcal, Cessna 1234MA at 3500ft over livermore airport, would like to transition through Class B for a bay tour. - Repeat your request.

Norcal: Cessna 1234MA, CLEARED INTO CLASS B, maintain 3000ft, squawk 1510. -- one marked in red is the golden tagline or "magic word" you need to hear from the controller. Without which you are not supposed to enter that airspace. If you do, its a violation and you may end up loosing your license.

Norcal (Alternate): Cessna 1234MA, remain clear of class B airspace -- STAY OUT of airspace.

Important points:

Even if ATC does not use the exact words (may use it differently or forget about it), its your duty to confirm that as its your license which is in line of fire. Ask ATC.
If ATC gives a vector (e.g. turn right heading 130) which may result in a flight path into class B, its your responsibility to be aware of it and ask ATC if you are cleared into Class B. Better ask then be sorry.

Class C:

Typically medium size airports (in terms of traffic) are classified as Class C (Charlie) e.g. San Jose etc.
Shape of class C is cylindrical with an outer shell.
Requirements to fly in Class C are list here: Requirements (pilot certification, equipment - transponder, comm etc).
Communication procedure - You have to establish 2 way radio communication to enter into Class C before you enter the airspace. Most likely you would have to speak with an area controller before you can enter the airspace and may not be directly with the ATC tower of that airport. You should communicate atleast 10 nm in advance. Sample communication with Class C controller

Aircraft Calling: Norcal, Cessna 1234MA at 3500ft over livermore airport, would like to transition through Class C for a bay tour. - Using the standard phraseology of who,where & what. Assuming you are flying through a class C.

Norcal: Aircraft calling standby. -- This means that they have just acknowledged your presence but no permission has been granted yet. KEEP OUT OF AIRSPACE, may have to circle around.

Norcal: Aircraft calling, say your request.

Aircraft Calling: Norcal, Cessna 1234MA at 3500ft over livermore airport, would like to transition through Class C for a bay tour. - Repeat your request.

Norcal: Cessna 1234MA, CLEARED INTO CLASS C, maintain 3000ft, squawk 1510.

Norcal (Alternate communication): Cessna 1234MA, standby - If the controller speaks up your aircraft tail number then also you are cleared into the airspace as that is establishing a 2 way radio communication.

Important points:

If ATC gives a vector (e.g. turn right heading 130) which may result in a flight path into class C, its your responsibility to be aware of it and ask ATC if you are cleared into Class C. Better ask then be sorry.

Flying to a uncontrolled airport

2012-03-08T11:43:00.000-08:00

Once you get your wings, it opens up the world for you. Your travel will take you to different types of airports e.g. controlled, uncontrolled, military (maybe) etc.
In this post I would like to touch upon a plan, communication and any other important aspects around flying to an uncontrolled airport. For this I will take you for a VFR flight from my home airport of KRHV (Reid Hill view airport) to KCVH (Hollister).

Step 1 - Prepare a flight plan

Get weather from adds.aviationweather.gov or any other aviation weather websites. Most important step for VFR flight. Links on my blog.
Pull your sectional chart and identify the start and destination and mark with pen.
identify checkpoints preferably every 10 nm. The checkpoints should be clearly visible from your altitude e.g. large warehouse, road intersection, water body etc. Identifying checkpoints close enough will help you correct your flight path sooner if you deviate. You can also use VOR, DME if you have the equipment.
Do time, distance & fuel calculation, based on the altitude you are flying. Altitude will be decided by the magnetic course if you plan to fly above 3000 ft e.g. 0-179 degree, odd + 500 ft MSL (3500,5500); 180-359, even + 500 ft MSL (4500, 6500). Refer FAR 91.159 . In this flight plan its 130 degrees and hence odd + 500 ft.
Do weight and balance and ensure you are within the CG limits of the aircraft you are using.
Identify in your flight plan, TOC (top of climb) & BOD (beginning of descent).
Once you have the flight plan ready, make a final call to get weather briefing and if required file VFR flight plan by calling FSS on 1-800-WXBRIEF. Important points to obtain are, route of flight, weather at destination, return flight weather etc. You should also obtain any flight restrictions like TFR, NOTAMS (runway closure) etc.
Check AFD for details of KCVH e.g. frequencies of ASOS/CTAF, runways available, runway length, runway lighting, fuel stations etc.
Usually in my flight plan I draw the runways and the my expected flight direction. This gives me the picture of how I will make an entry.
Now you are all set for the travel. Start your engines and contact ATC and take permission to take off. Bon Voyage

See this image below for some help.

credits - skyvector.com

Step 2: Enroute (assuming no flight following)

Communication is the key word. Giving your position reports regularly is very important in VFR flight. In the above plan, after taking off from RHV, you should tune in to the next nearest airport e.g. South County and give position reports.

Position call 10 nm ahead

Position call 5 nm ahead

Position call abeam

Keep scanning for traffic. Use standard scanning techniques.
Get ASOS/ATIS/AWOS information of airports enroute if available.

Step 3: Descend and Land

Get ASOS/ATIS/AWOS information of destination airport if available atleast 10nm ahead. This will help you visualize the weather condition and if appropriate for VFR landing and also the winds will give you a clue of the runway to land.
Start descending based on your flight plan to the destination airport.
Descend till 1000 ft above traffic pattern when approx 1nm away e.g. if pattern altitude is 1500ft then descend to 2500ft. This is required so that you can identify the windsock and general direction of wind. Will help you to determine the runway to land
Once you have identified the runway to land (by checking the windsock or as advised by any other aircraft in the pattern), then you should plan to enter the traffic pattern. Remember you are at 1000ft above TPA. As per FAR you should use the 45 degree entry procedure. See image below.
Make 45 degree entry into the downwind leg after descending to TPA. You should give position report for 45 degree entry, downwind, base, final and after clearing the active runway.
Voila you have successfully made it to the airport.
Now taxi to the terminal, fuel up, freshen up, and prepare your flight plan for the return.
Don't forget to close flight plan if you have opened any with FSS.

credit - wikipedia

Sample position report calls. Format is "Airport name traffic; Who; Where; What; airport name". This is suggested only and can be tweaked as required. Idea is to communicate and give as much information as possible so that other aircraft in the vicinity can visualize your position. This is called situational awareness.

Position report to South County @ 10nm -- " South County traffic; Cessna 1234MA; Is at 3500 ft, 10 nm North of the airport;Will be overflying abeam the airport for hollister; South County" -- North with respect to the airport and your aircraft. You will have to visualize your position. You can cross check with your heading indicator i.e. if the tail of the heading indicator is pointing to 180 then you are north of the airport heading south. Use N=0,E=90, S=180,W=270.
Position report to South County @ 5nm -- " South County traffic; Cessna 1234MA; Is at 3500 ft, 5 nm North of the airport;Will be overflying abeam the airport for hollister; South County"
Position report to South County @ abeam -- " South County traffic; Cessna 1234MA; Is at 3500 ft, abeam the airport;for hollister; South County"
Call 1 - 10nm away -- "Hollister traffic; Cessna 1234MA; Is 3500 ft, 10 nm North of the airport;Inbound for landing, any other traffic please advise; Hollister" -- Idea is to get traffic pattern or any other useful info from other aircraft.
Call 2 - 5nm away -- "Hollister traffic; Cessna 1234MA; Is 2500 ft, 5 nm North of the airport;Inbound for landing, any other traffic please advise; Hollister"
Call 3 - 1nm away -- "Hollister traffic; Cessna 1234MA; Is 2500 ft, 1 nm North of the airport;Will be circling above the airport to check wind direction. Any other traffic please advise; Hollister".
Call 4 - Circling -- "Hollister traffic; Cessna 1234MA; Is 2500 ft, above the airport;Will be circling to check wind direction. Any other traffic please advise; Hollister".
Call 5 - 45* entry-- "Hollister traffic; Cessna 1234MA; Is at 1500 ft; Inbound 45degree for downwind on runway 32; Hollister".
Call 6 - downwind entry-- "Hollister traffic; Cessna 1234MA; Is downwind; Inbound for landing on runway 32; Hollister".
Call 7 - base entry-- "Hollister traffic; Cessna 1234MA; Is base; Inbound for landing on runway 32; Hollister".
Call 8 - final entry-- "Hollister traffic; Cessna 1234MA; Is at final; Inbound for landing on runway 32; Hollister".
Call 9 - After landing and clearing the runway -- "Hollister traffic; Cessna 1234MA; clear of the active runway 32; Hollister".
Call 10 - hold short and Taking off -- "Hollister traffic; Cessna 1234MA; is holding short of active runway 32; Will be a straight out departure to north;Hollister".
Call 11 - upwind -- "Hollister traffic; Cessna 1234MA; is upwind from runway 32; Will be a straight out departure to north; Hollister".

Comments appreciated from viewers so that I can enhance this post and correct for any mistakes.

Why aircraft's fly at high altitude

2012-03-05T14:01:00.001-08:00

Reasons:

Terrain clearance - As the land is not flat and has obstructions (man made or natural), to keep it clear of them aircraft need to fly high
Less Air resistance - Since air is thin at higher altitude, the resistance is less and it can travel efficiently and faster.
Low fuel requirement - As air is thin, the fuel air mixture needs to be leaned. This means that aircraft will get more performance with the same amount of fuel as it would have got at lower altitude.
Jet Stream - At high altitude above 30000 ft, the jet stream which moves at excess of 50kts (in winter it goes to 100kts or more) helps aircraft fly faster which are moving the same direction as jet stream i.e. it adds to the ground speed. Though travelling in opposite direction will reduce the ground speed.
Higher TAS and ground speed - Since less air at higher altitude the TAS is higher. This means that overall ground speed will increase.

High altitude operations

2012-03-04T13:32:00.000-08:00

This topic is usually asked in a checkride by examiners. Let us try to understand what questions are asked and how to respond to those.
Before that I would like all of you to read my previous post about relationship between pressure, temperature, density and altitude.
Effect-of-temperature-and-pressure

Also see the following mathematical relationship:

where

L is lift force,
ρ is air density
v is true airspeed,
A is planform area, and
is the lift coefficient at the desired angle of attack, Mach number, and Reynolds number

In summary, At high altitude, you have lower pressure, lower temperature and hence lower density (i.e. amount of air molecules per cubic meter). Now the lower density is the main reason which affects the takeoff/landing. Let's see how.

Question1: How is takeoff affected by high altitude?

Less engine performance -- Engine requires air to operate (i.e. burn fuel with air). But at this altitude density is less and hence less air for engine. This results in lower performance of the engine. That is one reason why you may (e.g. in cessna 172 its recommended to lean mixture above 3000ft) need to lean the mixture to correct the air/fuel mixture for best performance.
Higher TAS -- Higher true air speed. TAS is relative to the air your are currently travelling. Since engine performance is less, you will need to travel faster to get same amount of air required by engine for best performance. Note your indicated airspeed will remain the same i.e. you will still takeoff at the same indicated a/s.
Longer takeoff roll -- Since engine performance is low, aircraft needs to travel longer and faster to get the required amount of air to burn fuel optimally. Imagine you are travelling in a car and you open the window and keep your hands out. At low speed you will not feel the amount of air pushing your hands but as speed increases you will feel more air pushing your hands. Its the same principle. As you travel faster in aircraft, more air will start hitting your engine and it will be able to generate higher thrust. As part of flight planning you should calculate the takeoff roll so that its within the runway length.
Reduced maximum takeoff weight -- Higher weight may result in even longer roll as aircraft needs to travel faster to get the amount of lift to balance that weight and runway may not be long enough to achieve that required speed.
Reduced Lift -- As you can see from the mathematical relationship above, density is directly proportional to lift. Low density translate to less lift.

Question2: How is landing affected by high altitude?

Higher TAS -- As above, since amount of air is less to reach the same indicated airspeed required for landing the TAS is high.
Longer landing roll -- As TAS is higher the aircraft is travelling faster. To slow down it will need longer runway to stop. Also, since air resistance is low that as well contributes to longer landing roll.
Less resistance to land -- As air is thin, it provides less resistance for the aircraft to stop and increases landing distance.

These are some of the reasons, why performance is always calculated against density altitude. Note the above reasons also apply to airport with high temperature, as that also results in lower density. Hence if you are at sea level but very hot for the day and lower density, it will behave like high altitude airport.

Effect of temperature and pressure on density

2012-03-01T14:24:00.002-08:00

What is density: Density is mass per unit volume expressed usually in kilogram per meter cube (kg/m³). Imagine you have a box of size 1meter x 1meter x 1meter. If you put air inside it, it can hold uptill the entire space is filled up. That is the maximum capacity it can hold. Our atmosphere is also like that. At sea level at 15°C it is 1.225 kg/m³

Effect of pressure and temperature as height increases:

As you climb up the atmospheric pressure above you reduces i.e. if at ground level you have 1010 mb or 29.92in of pressure then at 1000 ft above it will be less i.e. the amount of air above you and hence the pressure exerted will be less. Other way to understand is if you apply pressure then molecules are closely packed and hence more dense. Reverse when you remove pressure.
Secondly the temperature reduces as you climb higher e.g. at ground it may be 15degree Celsius but at 1000ft height it will be less say 10 degree Celsius.
Density reduces as height increases (at sea level 100%, at 20000 ft 50%). Scientifically it has been put into this formula.

where ρ is the air density, p is absolute pressure, R_specific is the specific gas constant for dry air, and T is absolute temperature

As you can see from the above formula, density reduces as pressure reduces, which means that as per point 1 above, since height increases, pressure reduces and hence density reduces. So far so good. We have established the relationship.

Now to point number 2, as temperature reduces as height increases density increases (inversely proportional). But that's contradicting or cancelling pt number 1. However that is true but density reduction due to pressure is more than density increase due to temperature decrease, resulting in net decrease in density.

Effect of water vapor to density: Introduction of water vapor in atmosphere i.e. making the air humid. Humidity reduces density. Why? Cause water has less molecular mass than air and hence when water is added to atmosphere it displaces air in the given cubic meter volume but results in lowering of density.

UKDVPHMYAQXD

Understanding drag

2012-03-01T12:07:00.002-08:00

Figure 1: Drag graph

Parasite Drag: Sum of Form drag, Interference drag and skin friction drag.

Induced Drag: by product of airspeed. caused due to downwash....in a cambered wing, on the upward side air is flowing faster than the lower side. Now this fast moving air above and slow moving air below, meet at the trailing edge and cause turbulence called vortices. These vortices is downwash and it causes opposite reaction in form of drag called induced drag. Refer figure 2 below (RW = relative wind).

At low airspeed to maintain lift, pilot needs to increase AOA (angle of attack), as a result on the upside the air flows even faster as its more curved and lower side it travels the same speed. This causes even more turbulence at the trailing edge. Hence at low speed induced drag is more.
However at high speed, AOA is less and hence turbulence at trailing edge is less causing less downwash and less induced drag. Refer figure 1 above.

Figure 2: Credits - Civil Air Patrol

Travis AFB Airshow

2012-02-14T21:24:00.000-08:00

close call for 2 F16s

USAF thunderbirds in their F16s

C17 Globemaster. Picture taken by me @ Travis AFB

Ground Effect

2012-02-14T15:30:00.000-08:00

This topic usually is considered difficult to understand and many of my friends have been confused by it. Let me try to explain it here in my own words, not in depth but conceptually. I would recommend reading multiple books or sources to get an accurate picture. Hopefully its easy to understand.

Ground effect occurs within a length of one wingspan over runway....in this ground effect, the induced drag reduces and giving a false sense of lift....hence during takeoff aircraft may take off at say 50kts instead of 60kts...but if we come out of ground effect immediately..there is not enough lift and aircraft will sink back...hence if the aircraft lifts off earlier in ground effect...its recommended that maintain in ground effect till the a/s increases to required i.e. 60kts and then come out of gnd effect.
gnd effect occurs since the downwash (wingtip vortices) are effected by the runway or ground.

Studying for exams

2012-02-14T15:07:00.000-08:00

Now that you have decided to be a private pilot and started taking lessons, you need to study for the exams. Now there are many books that you can refer to but it can get overwhelming. I would recommend using a standard study guide like jeppessen pilot book. I used that to prepare for all of my training including private, instrument and commercial. The language is easy to understand and has interesting images which makes it much easier to visualize. Apart from that get yourself the following books/material:

Sectional map for the area you will be flying. I used FAA sectional map.
Airport facility directory (AFD). This would be very handy in flying but equally important while studying as it has lots of useful information.
Question bank (I used Gleims)
FAR/AIM (latest publication based on year)

You may additionally purchase videos from kings school or sporty's which helps a lot.

There is no shortcut to studying. You may think why not study the question bank and clear the exam, its like you know how to drive but you will not know the rules. Hence I would recommend you to study the books thoroughly and then jump on to question bank.

If you consistently get 80-85% in sample test, then you are good to go for the exam. Just don't forget to take the endorsement from your instructor.

There are 2 patterns of exams given by different groups (lasergrade or CATS). Be sure which one is available in your school or wherever you plan to give and prepare your questions accordingly.

Good Luck......

Learn to Fly - First Flight

2012-02-14T13:51:00.000-08:00

Welcome to the fascinating world of flying. Having wings is rewarding. Its a totally different experience and very pleasurable. It opens of avenues of exploring for you. So if you are interested in flying, go ahead and fulfill your dreams. Flying has always been my passion and dream. But I not only dared to dream but make it a reality. If you have made up your mind and are dedicated to learn a new skills, here are the steps for you.

Locate a flying school/club near your location. Its not difficult, you a google will turn up some nice flight schools. If you have any friends or referrals that's good too and it made your choices easier.
Do some research on the flight school. Its always a good idea of find out the reviews on the flight school. If the flying school/club has lots of budding pilots then ofcourse that gets a higher ranking. What you need to look in a school is, number of aircraft (single engine e.g. Cessna 152/172 etc), students at any point of time, number of instructors (in case you need to work with another one) and of course the maintenance staff.
Find our the instructors available in that school. You may get the list of instructors from the website of the school or by reading reviews and other information on net. Finding out a good instructor is equally important as finding out the school. The instructor will instrumental in giving you the wings you always desired.
Contact the school and make an appointment with the instructor. The schools always have an intro flight option. Its always important to take that intro flight as after that you will come to know if thats something up your alley.
Take the intro flight. I am sure you would love it. I had some nervousness about it and was little shaky after the flight, but I knew it instantly that I want to fly.
After the flight talk to the instructor, its important that you guys gel well. Experience counts with the instructors but many times you will find less experienced ones taking extra steps to make it enjoyable for you. Its all about being comfortable. My first instructor was not that experienced in teaching (I think I was first few of his student) however very knowledgeable guy.
Get to know about the school.
Do the paper work with the school to enroll. Some clubs have membership fees that you need to pay.
That's it. You may now fly and enjoy the sky.

Once you enroll and are committed to learn flying. School will ask you to follow some steps like take medical (class 1/2/3 depending upon your need). I would suggest go for Class 1, in case you want to take your passion steps ahead to become commercial pilot.

Secondly you need to go through a background check with TSA (and possibly finger printing if you are a foreign student).

Now you are legal to fly....enjoy.......