karashy works

Lego Star Wars? Hey son! I'll make it for you! - 6-Day Venator Star Destroyer Papercraft Making Record

2018-04-23T00:55:00.001-07:00

My son is 8 years old and is a great Star Wars fan.

He likes Star Wars Episode 3's Star Destroyer.

He went to Mart several months ago and saw the "Star Destroyer" released in Lego

He wanted to have it very much. So I thought I'd buy it for him

but my wife objected. Of course, It is too expensive for a child.

So, I was worried and made a decision.

"I make it myself and give it to him !!"

I put off work and started 3D work. Because it was not a model to render,

I thought it would be easy to make the outer frame and spread it.

But ... Suddenly I was greedy.

'Let' s make it larger than LEGO anyway. 4 feet is enough to be satisfied ^^ '

I started designing 'LEGO' as competition.

The output used the A2 printer in the office.

The method of cutting and attaching several pieces of paper is also problematic in terms of firmness and too much work.

I was able to make a large output because it is capable of large output.

If I did not have an A2 printer, I would have had to make it smaller.

And I think during the design, if the size is more than one meter, it will definitely have a problem with the stiffness of its upper deck.

So I chose a foam board with a thickness of 5 mm.

It's stronger than paper, it's lighter in weight, so it's better for kids to play.

Of course I recycled foam boards from the office.

(If you are working with a new foam board rather than a recycled foam board, the production cost will probably be significantly higher)

I had a lot of troubles and I was working on it.

There were also many mistakes and trial and error. Therefore, there is a partial error.

I do not plan on making a complete paper craft project,

It differs from the design for paper craft.

The first task was to line up watching movie scenes and model pictures of the Internet.

6-Day Venator Star Destroyer Papercraft Making Record

1. Upper deck works

The shape was once worked, but I had no way of knowing how much the angle of the top plate had to be tilted to fit the side and bottom plates exactly.

So I decided to try the simulation using a 3D graphics application

To test it lightly, I opened the Rhino 3D and imported the outlines worked on the illustrator and attached an angle.

I'm looking forward to seeing a rough figure. Simulation is complete

Open the source for the 3D mapping found on the Internet, map it nicely, print it out, and arrange the outline

The square on the upper left is the A2 paper size.

Print each part separately and firmly attach the print media to the foam board with spray adhesive (3M 77)

Cut along the outline with paper

When I was doing 3D work, if the center was empty like that

It seems to break when attaching the bottom plate or attaching the bridge tower.

So I decided to build several support pillars inside. ^^ (work is getting more and more ^^)

As simulated, the support is loaded in 1: 1 size and printed outlined

Attach it to the foam board with a weak adhesive (3M 75) (because it will be removed later)

6-Day Venator Star Destroyer Papercraft Making Record

2. Side operation

This time I work on the side of the star destroyer.

This part looks great to me.

Use the sources to map them three-dimensionally and calculate them well.

This also required the help of a 3D program.

The screenshot is not cut yet before applying the TRIM command

But I will then extract the line from the cut side and load it into Illustrator.

Map according to the outlined line. (There is no rule, just make it look nice)

It does not enter A2 paper at a time, so it divides into two, and outputs one copy of each of the left and right on one A2 sheet.

It is necessary to apply some cutting process to the folded surface after cutting it on the foam board.

In the case of the side, the direction of turning inward and outward are different, and there is a place to be bent inside the thickness of the foam board.

This part is cut with a knife to cut the angle of the blade.

(So I printed out the mapping output and the board output separately, processed the board first, and attached it again.)

6-Day Venator Star Destroyer Papercraft Making Record

3. Attach upper deck, side and supporting column

It is time to attach the upper deck, the supporting columns inside, and the side to support the left and right.

The attachment of this part is the part that determines the most basic strength in future model work

Attachment tool uses 'Loctite 401' strong adhesive. (There are 50% stronger products in the blue barrel than just 401)

However, the performance of this adhesive is so strong that if it goes wrong, it will not be reversible.

Be careful when attaching because it is bigger and does not come in at a glance.

It's all out of sync with this work.

I am not perfect, but I am well attached.

I felt I was not taking a picture so far, so I started taking pictures from this part.

If you look down, there are rows of support pillars inside. (We removed the middle of the supporting columns.

This is because the dock on the bottom of the star destroys will be installed)

The red bar parts and the turrets on the upper deck are printed separately and placed on top of the upper deck part to create a height difference

(It looks like you are watching the movie more closely ^^)

It's pretty cool to see that the mapped output has a solid three-dimensional look.

It is not perfect yet, but I like it already. I wish my son would be glad to see this.

6-Day Venator Star Destroyer Papercraft Making Record

4. Rear deck work

It is time to work on the 'stern' part of the STAR DESTROYER.

I put off the bottom work below. Because if I attach the bottom plate first, then the nozzle work on the rear part will be considerably difficult.

Moreover, since the supporting pillars are already blocked inside, it is difficult to press the mounting surface by hand when attaching the bottom plate and the side.

anyway,

Typical paper models are also made separately for each part

This board model is heavier and harder than paper, so it is different from paper model.

When my son catches this, he will hold wing part or rear deck with his hand. If this part is empty like a paper model, it is likely to break due to weight.

So I decided to fill it with a foam board.

Using Illustrator and Rhino 3D, we get the size and outline, then make the boards for the output of the board cutting.

I made this shape by putting the cut board side by side ^^

(The left board is the lower part of the rear, the lower part of the nozzle.

Attach the output paper for mapping onto the board chunk.

(The same as filling a piece of paper with a chunk of board)

6-Day Venator Star Destroyer Papercraft Making Record

5. Nozzle part

It was the third day of the start of the nozzle part.

While I was working on other parts, I was always full of worries about how to make a nozzle.

The work always lasted until about 3 am

I also turned on my eyes and looked for cylindrical objects until I came home and fell asleep.

But ... there is nothing useful.

Cans of toilet paper, drink cans, hair spray, glue ...

In the end, I had to make the nozzle using a foam board.

Oh, my God!

Repeat the movie scene, locate the nozzle in the Illustrator, and create the inner nozzle support plate in the Rhino 3D.

The support plate was a part that was not planned in the beginning, but when I worked, I realized that it is a necessary part.

First, calculate the diameters of the nozzles and spread them. 360 degree divide a few ... In this way, it is divided into the easiest to divide by the minimum cutting. If you split a lot, it gets closer to the circle, but it gets harder because you have to cut a lot

Put the printed paper on the foam board lightly, cut the outer edge with 80% sheath as calculated.

Then fold the section of the sheath and make it cylindrical.

If the calculations and cuts are good, the cylinder will come out properly.

To make the nozzle section look better, I add a muffler made by calculating more widening

This will make the nozzle more aggressive.

The smallest outside nozzle is thin, making it difficult to make with boards

So I decided to use the center of the CD case that I found among the things I have.

Next is the time to build a backing plate that will hold these various nozzles firmly.

Print out the drawing created in the nozzle preparation section and cut the board.

(It is very dangerous and difficult to cut a circle with a large cutter knife for the board, so it can be cut off roughly because it is out of sight.)

This is the plan of the support plate.

If the calculations are done well, I can attach more firmly than when I only attached the ends of the cylinders

Cut off F1 in the drawing and cut off F2 and F3. Next, let the nozzles pass through F1. But do not stick with glue yet!

Now fully attach to F2, F3 with strong bond.

Then check that there is no abnormality in angle and fix F1 and cylinders too.

(It looks awesome than i expected. )

6-Day Venator Star Destroyer Papercraft Making Record

6. Body - Nozzle - Assemble Rear Deck

The most worried nozzles are solved well and I am looking forward to it.

Now the modules of these nozzles must be firmly attached to the support plate on the back of the body.

Of course, this should use a strong bond.

The shape of the nozzle support plate is calculated with an angle so it must be attached exactly.

If you stick it out wrong, you may have difficulty putting the bottom plate later

Next, insert the rear deck made in the previous step between the nozzle modules and attach it as a strong bond.

It is the top and bottom view that the attachment is completed.

Now I can see how full the size is.

I took a picture with the bills for size comparison

6-Day Venator Star Destroyer Papercraft Making Record

7. Rear deck - recreate

I rested the weekend and went to work on Monday and I saw the star distroyer again.

I did not like the shape of the rear part.

Suddenly, I thought of a better way, so I decided to take it out and re-create it.

Bond performance is too strong, so it may break the top plate.

So I cut it off with a knife.

The new plan to recreate is to put the rear deck on the upper deck.

This will increase the amount of glue and the bridges will be firmly attached.

I cut one board by test and inserted it. It looks like a very good plan.

I have recreated the board bundle with the confirmed drawing.

When I put the bundle into the test, I like it a bit tight.
The top of the rear has one more consideration for the connection with the bottom.

That's why I created a hole to combine the fin in the lower part ^^

Print the mapping paper and attach it to the rear deck surface.

The following is the lower fins of the rear deck.

I tested it and it seems that the plan was well done. It is just before joining after attaching the mapping paper.

After joining the top and bottom, the body is attached.

(I did the weathering work on the side of the nozzle before output, and it was nice after all)

The whole process is about 60 ~ 70%

6-Day Venator Star Destroyer Papercraft Making Record

8. Bridge Tower

Bridge Tower planned to make multiple boards like a rear deck.

This is because it is robust and computationally convenient.

It was decided by the width and the thickness of the board.

Of course, the original design of the Bridge Tower is suitable for this.

Separate each part in Illustrator program. The number of boards will be determined.

The board pieces were cut in the shape of a bridge tower, and then tested.

It's positioned to the planned width.

Next, print the mapping paper and attach it strongly to each part with a spray adhesive.

(It does not attach the bridge bundles yet.)

6-Day Venator Star Destroyer Papercraft Making Record

9. Rear hood

Currently, the back side is not treated at all around the nozzle.

I have been working on the rear hoods outside the nozzle while referring to the photos of the Star Destroyer

Based on the rear view line worked in Illustrator, tilt in 3D and trim the cylinder to find the cutting line.

I cut off the foam board on the back, and finished the rear jet hood ... ^^

It is attached to the back of the body.

This section also requires a precise tilt calculation because there is a lower plate and attachment area to work on later.

6-Day Venator Star Destroyer Papercraft Making Record

10. Front

It is a very triangular shape, but there is a very small front which is also called 'front'.

The area is small, but it is a very important part because it should touch both side panels and lead to the front and the slope of the upper and lower plates starts.

I put a small part to make the detail ...

But when I look back at the movie after the work, this part did not come out but it was part of it

6-Day Venator Star Destroyer Papercraft Making Record

11. Lower plate

It is the work of the lower plate that affects the completeness of the work so far.

Output the mapping paper as designed by the illustrator and attach it directly to the board.

It will be cut and used together with the foam board.

As in the movie scene, the hole part is also cut to make the center dock.

I attached the front of the bottom plate first without attaching the whole bottom plate.

Because it is more accurate to hold the angle with the front lower plate and attach the rear lower plate

It is also easier to attach separately to work on the dock in the center of the bottom plate

Now attach the back of the bottom plate. It was a very difficult part.

It should be at an angle to the inside supporting posts and at the same angle to the side

It should also fit tightly with the front plate.

But the bond is so powerful that it only gets fixed in just a second.

I had to be very careful.

6-Day Venator Star Destroyer Papercraft Making Record

12. Center bottom deck

This deck is the reason I removed the middle support from the support posts at the beginning of my work

The inner wall of the deck will be raised up to the top plate and serve as a pillar

Print the mapping and cut it with the board to create a square column.

(The mapping will be inside the column)

Apply a strong bond to the bonding surface of the column, then push it into the hole before hardening to secure it.

The end of the column is bonded to the top plate.

6-Day Venator Star Destroyer Papercraft Making Record

13. Attach body, tower and rear

It is finally the bridge attachment that will be the end of the main work.

It was so easy to do it because it was a good part of the calculations so I could stick it out in order.

Invisible areas are reinforced with strong bonds.

6-Day Venator Star Destroyer Papercraft Making Record

14. Tower Bridge

I built a tower on the upper deck but it looks strange because there is no bridge

This time I will build a bridge of the tower.

Now we will only work with the thickness of the foam board without the help of 3D.

(The complicated calculation is over)

After drawing only length and width in illustrator, we set height by form board thickness.

I would attach the bridge to the upper section standing on the tower ... Is it really strong?

If the son pulls on this part, can he hold it?

So I needed a more robust combination method.

I will add a vertical bar to the bridge and tower to increase the adhesive side.

The bottom board piece is cut to the thickness of the vertical bar

It is attached to the top board and is mapped over it.

Vertical bar is combined with bridge. Now I'm going to stick that bar into the tower and bond it.

Fixed. You can see the vertical bar on the side.

6-Day Venator Star Destroyer Papercraft Making Record

15. Add towers and rear pieces

When planning the tower and rear section, there is a part left behind to be worked on separately due to the board thickness and angle of cut.

A small piece on the rear part. I did not have a way to cut it at once to create a mapping map.

So I had to make it separately.

6-Day Venator Star Destroyer Papercraft Making Record

16. Laser Cannon

Now the last detail work.

I will make four laser canons that are placed to the left and right of the bridge tower and two laser canons that are on both sides of the body.

Use the Illustrator to print the mapping and cut it with the board

But what makes a cylindrical bar for a laser canon?

It's a straw. HAHA~

I've also painted to change the straw to black, but it's easier to wind it with black tape

It seems to be more aggressive when it attaches to each position.

This time the Canon is on the side. Straws too ... This is a thinner straw for children.

Wow ~ It's a lot nicer than nothing.

The body is finished. It's about 115 centimeters in size.

It's about 3.8 feet.

6-Day Venator Star Destroyer Papercraft Making Record

17. Partial supplementary work

Every time I look at the side of Tower Bridge I see a black board.

So I made an additional mapping. It's better.

6-Day Venator Star Destroyer Papercraft Making Record

18. Stand

Now, the final step of all planned work is finalized.

It is a stand that will support the star distroyer.

In fact, it is a part of 0% useless for the purpose of giving a son, but it is just my satisfaction. ^^

The contents of the plate worked with illustrator.

I've put in the names, specifications, logos and my signature.

I made a stand by calculating the height so that the side of the destroyer is horizontal.

Therefore, the height of the stand located at the front will be higher ^ ^

The plate is attached to the side of the stand located at the front.

6-Day Venator Star Destroyer Papercraft Making Record

19. Completion

After making it, I could not say anything for a long while looking at it.

god.... I made this…

It was a six-day long expedition. At first I thought it was nothing but it was not.

It is not easy to draw, but it was a very difficult work to create completely new from the draw.

And the last saved Illustrator file size is over 6 gigabytes with lots of mapping data.

At the same time, when I opened and worked on other files, my Mac Pro was also often crashed.

The average board thickness is 5.5 millimeters. There is a slight difference between boards, but since it is recycled, some of the boards are slightly bent so that the error rate is higher.

I cut it a little more as needed because I am not a machine. ;-)

When all my colleagues had left, I was alone and worked until 3 am.

And I only slept three hours and went to work the next morning ...

I did my best for six days.

Son ... is it my fault you showed Star Wars?

'Even if my son breaks this thing out tomorrow, do not get angry ....'

This is the biggest last challenge I've had. Oh ... please ....

By the way... where should i put this?

===========================================================================

6-Day Venator Star Destroyer Papercraft Making Record

20. Next Day

With his reaction, my plan seems to be quite successful.
:-)

hey son, i'm your father.... hoook~ hooook~

-------------------------

## This article re-posted the article written in 2009.

Instruction for TECHNOIR MK1 for iOS4 HD Installation

2011-11-21T00:04:00.001-08:00

If you Can't See Every Screenshots and Pictures
in this Instruction, please move to link below:
http://akhavo.blog.me/100143359135

i'm sorry about that.

Instruction Guide for
TECHNOIR MK-1 HD by Kamahn

1. SpringJump Install
TECHNOIR Required page shortcuts to move more fast page to page.
And so you should install SpringJump.

CYDIA >> Search >> Springjump >> Install >> Respring

You can find these ‘springjump’ standard shortcuts.

Springjump >> Jump Icons >> Turn Off All page switches >> Respring

So all of Springjump Standard shortcuts are Hide.
Then you should put other springjump shortcuts for TECHNOIR in your iPhone.

Check these more SpringJump shortcuts (36 icons) in TECHNOIR THEME Package.
(If those icons already automatically installed with TECHNOIR Theme you can skip this Step.)

Launch any iPhone Explorer Applications on your Computer (ex. iFunBox. DiskAid)

Put these all springjump shortcuts in this path -> root/application/
and Respring.

There are so many springjump shortcuts in your iPhone’s home screen.
Springjump Setting is Complete.

2. Shrink Install
TECHNOIR theme Need to desizing icons. so you have to do install shrink in CYDIA.

CYDIA >> Search >> SHRINK >> Install >> Respring

Settings >> Shrink >> Scale >> 66% or 75%
(have it your way-but i don’t recommend you 85% higher)
and get out of Settings... then You’ll find strange Homescreen.

shrink setting for THECHNOIR is complete.

3. Iconoclasm InstallUnique Layout required to use TECHNOIR Theme.

CYDIA >> Search >> Iconoclasm >> Install >> Respring

Check these Layout file for Iconoclasm in TECHNOIR THEME Package.
(If those icons already automatically installed with TECHNOIR Theme you can skip this Step.)

Launch any iPhone Explorer Applications on your Computer (ex. iFunBox. DiskAid)

Put this Layout file for Iconoclasm in this path -> root/Library/Iconoclasm/Layouts/
and Respring.

Settings >> Iconoclasm >> Layout >> TECHNOIR MK1 >> Enable Iconoclasm
>> Automatically Respring
(Warning :
Don’t Touch Enable Switch first. because this switch just doing Immediately Respring)

so your iPhone has TECHNOIR’s layout. Iconoclasm Setting is complete.

4. Apps Location Arrange
TECHNOIR layout has 6Pages. those pages’s subjects are
‘MAIN’, ‘INFO’, ‘PHOTO’, ‘MEDIA’, ‘GAME’, ‘SETT’.
(Of Course you can change subject after you install theme complete.
and I’ll give you changable menu PSD file link URL where last step of this instruction )

then you have to do work that move apps location that have it your way.
But! you should have to do this ONE !

SpringJump Shortcuts should be appointed location !
Page 0 - Page1 - Page2 - Page3 - page4 - page5 per all 6 Pages like below screen shots.

have done? good work. go next step.

5. PerPage Install
TECHNOIR has unique page design with PerPage. so you should install PerPage in Cydia.

CYDIA >> Search >> PerPage >> Install >> Respring

Check these Folders for PerPageHTML (6 Folders) in TECHNOIR THEME Package.
(If those icons already automatically installed with TECHNOIR Theme you can skip this Step.)

Launch any iPhone Explorer Applications on your Computer (ex. iFunBox. DiskAid)

Put these all Folders in this path -> root/User/Library/PerPageHTML/
and Respring.

You can find Couple of App Icons has same name ‘Perpage’
you should launch ‘PerPageHTML’ App. (like above screen shot)

All you have to do is just choice page widget per correct Page number
from page1 till page 6.

And Press iPhone’s home button... so automatically Respring.

then you can see TECHNOIR’s page Menus. yep! you are almost done.
follow some step more.

6. SnowCover4 InstallTECHNOIR’s Lockscreen Music Player theme !

CYDIA >> Search >> SnowCover4 >> Install >> Respring

Check this another theme for SnowCover4 in TECHNOIR THEME Package.
(If those icons already automatically installed with TECHNOIR Theme you can skip this Step.)

Launch any iPhone Explorer Applications on your Computer (ex. iFunBox. DiskAid)

Put this theme in this path -> root/Library/SC4Themes/
and Respring.

Settings >> SnowCover4 >> Themes >> Technoir MK-1 HD

iPod >> Play some music and press sleep button to go out lockscreen
and press any button again.

Swiping Right and left or double tapping or swipe up and down.
probably work very well.
SnowCover4 Setting is complete.

7. Select Theme ‘TECHNOIR’ At last you are ready for select theme !

Winterboard >> Select Themes >> TECHNOIR MK-1 HD >> Back >> Respring

<< Battery Charge

TECHNOIR Setting is almost Done. but we have Last one step.

8. More Setting on Shrink
do you need Icon’s Label? TECHNOIR Style is Not use icon label.
but have it your way~ ;-)

Settings >> Shrink >> Label Scale >> hidden
and Press home button and go out home screen.

This is TECHNOIR Original style.

9. Fix two problems when you’ll meet folder Open
Probably you will happen to see two problems when you folder open.
(like screenshots below)

First, TECHNOIR background disappeared.

And, you can’t see All apps in folder if folder’s locate below.
and also you can’t scroll.

exactly first problem haven’t fix it every theme for iOS4.x in cydia (as i know :-) )
but we can make fix it with another easy way.
and second problem can fix with another tweak app in cydia.
let’s Fix it!

1) FIX IT! - background disappeared when you folder open. Don’t worry about this way. it is too simple.
you should background image files copy into the Photos folder in your iPhone. with iTunes.

Launch any iPhone Explorer Applications on your Computer (ex. iFunBox. DiskAid)

‘LockBackground@2x.png’, ‘Wallpaper@2x.png’ two files select. (root/private/var/stash/theme.xxxx/TECHNOIR MK-1 HD/)
and copy into your some of folder. (ex. wallpapers)
(if you install TECHNOIR MK-1 SD, you select ‘LockBackground.png’, ‘Wallpaper.png’ two files.)

Then you should Launch iTunes any version you have it.

Select Change Sync. folder that is copied background Images. (ex. Wallpapers)

then you should Sync your iPhone with iTunes for photo files.

and... so open settings on your iPhone. and select wallpaper tap.

wallpaper >> photo album

select lockbackground image (like above screenshot) and press setting button.

and you should also press ‘lockscreen’ button.
then lockscreen background setting is complete.

and next time is homescreen background setting. :-)

you select another copied image for home screen background. and press setting button, too.

and press ‘home screen’ button again. so background setting is complete.

Now, you can see background when you folder open. and while you are calling, too.

2) FIX IT! - can’t see all Apps in folder and scroll neither.this problem cause iconoclasm. i’m waiting for iconoclasm’s update for this problem.
then we need to help another tweak’s help for a while iconoclasm’s update.
and we....

to be continue... (Not complete yet. ;-) )

10. Personal Settings for Widget - Lock Clock
11. Personal Settings for Widget - RSS Feed
12. Personal Changing Page Menus
13. Personal Changing Dock Icons

Let’s Test it!

BMW 테마 1.4 - 아이폰 테마 --> 시디아 BMW Theme of Kamahn

2011-11-11T04:50:00.001-08:00

이번엔 'PogoPlank'라는 테마어플을 이용한 테마 입니다. ^^

기존의 화이트 및 블랙테마의 대부분은 스프링점프와 빈 아이콘을 이용한 페이지 레이아웃 배치 방법 이었지요

그러다보니 새로운 어플을 메인에 배치하거나 기존의 어플의 위치를 바꾸려면 막대한 작업시간이 필요했었습니다.

게다가 나머지 어플들을 '카테고리즈' 어플을 이용해 폴더별 관리가 가능했지만 접근시 딜레이 현상이 있고

탭으로 페이지 이동-폴더열고-어플 선택 이렇게 몇번의 과정을 거쳐야 어플의 사용이 이루어질 수 있었습니다.

게다가 필요없는 빈아이콘들도 계속 존재해야 했구요.

하지만 PogoPlank를 이용하면 이런 여러페이지의 공간에 대한 고민이나 중복되는 접근성의깊이를 단축시킬 수 있습니다.

자신이 설정한 카테고리폴더를 단지 왼편의 휠을 스크롤하는것만으로 선택할 수 있고 그 폴더를 터치하면 해당폴더의

어플들이 세로로 나열됩니다. 그중에 선택하면 되는 거죠. 메인페이지는 딱 한장으로 끝입니다.

여러페이지도 필요없고 카테고리즈 어플도 필요 없으며 새로운 어플의 배치도 고민할 필요가 없습니다.

그저 돌리고 선택하고 스크롤, 터치하면 되는 겁니다 ^^

아래에 보이는 움직이는 화면은 제 아이폰의 화면을 몇장씩 캡쳐해 애니메이션으로 붙여 놓은 겁니다.

실제 작동 느낌과는 차이가 있습니다. 모든 컷의 시간이 동일해서 실제 보여지는 것과 다르다는 얘깁니다.

왼편 첫째 화면은 락스크린 화면과 홈으로 들어왔을때 처음 휠이 등장하는 모습이구요

보시는 화면보다 실제는 눈깜짝사이 입니다. ^^;;;;

오른쪽 둘째 화면은 제가 BOSSPAPER라는 어플을 이용해 편법으로 배경에 변화를 준 겁니다.

예상하셨겠지만 여러장의 배경이 필요하고 만일 차가 앞으로 다가오는 사진이 동일한 앵글로 여러장이라면

차가 앞으로 다가오는 '움직이는 배경'이 만들어 질 수 있겠지요 ^^

BOSSPAPER란 어플은 여러장의 그림이나 컬러를 이용해 배경을 특화 시킬 수 있는 어플입니다.

단 위에 보여지는 화면은 제가 원래 원하던 만큼 빨리 배경들이 교체 됩니다만

실제 보스페이퍼는 5초가 최단 시간입니다. ㅠㅠ

즉 저 그림보다 훨씬 늦게, 그리고 부드럽게 교체가 됩니다.

그래도 나름 느낌 괜찮답니다. ^^

이 BMW테마엔 '락스크린테마'와 '락인포' 어플도 사용 되었습니다.

자 그럼 한번 따라해 보시겠습니까? ^^

<<설치방법>>

이전까지만 해도 제가 일일이 보내드린 메일의 첨부파일을 열어서 압축을 풀고

각자가 폴더를 탐색프로그램을 통해 직접 복사를 해야 하는 등 까다롭다기 보다는 귀찮은 과정이

필요했던 테마설치 작업이었습니다만 시디아 업로드를 통해 간편하게 진행될 수 있도록

공개배포하게 되었습니다. ^^

우선 이 테마를 설치하기 이전에 아이폰에 '포고플랭크'라는 어플과 '보스페이퍼' 라는 어플이 필요합니다.

현재 시디아에서는 차단된 상태이므로 구글을 통해 구하셔야 할것으로 보입니다.

1) PogoPlank 설치

오늘의 히어로 포고플랭크를 설치합니다.

이 어플의 설치는 각자 알아서 하셔야 합니다. (그리고 현재 이 어플은 유료 입니다만 공짜 버전이 어딘가에...)

어플을 설치하고 나면 아이폰에 이런 아이콘이 등장 합니다.

자 여기까지... 일단 설치만 해둡니다. ^^

2) BOSSPAPER 설치

다음은 변화되는 배경을 위해 보스페이퍼를 설치합니다.

보스페이퍼는 시디아에서 검색해 설치하면 됩니다.

해킹할때 설치한 시디아를 엽니다.

그리고 하단의 'SEARCH' 탭으로 가서 검색창에 bosspaper라고 입력합니다.

그러면 보스페이퍼 어플의 정보가 뜨고 이걸 선택해 우측상단의 install-> confirm을 눌러 설치 합니다.

그러면 또 아래와 같은 새로운 아이콘이 등장 합니다. ^^

자... 이번에도 일단 여기까지... ^^ 설치만 해둡니다.

3) 테마의 설치

시디아에서 'BMW theme of Kamahn for Pogoplank' 와

'BMW theme of Kamahn for Winterboard' 두가지 테마를 검색하고 각각 설치합니다.

4) 포고플랭크 설정

아까 설치 후 생겨난 포고플랭크의 어플 아이콘을 엽니다.

그러면 다음과 같은 포고플랭크 어플의 메인 화면이 나타납니다.

그러면 가운데에 있는 Enable PogoPlank 버튼을 옮겨 활성화 시켜줍니다.

다음 하단의 탭중에 오른쪽 'Themes' 탭을 눌러 열니다.

아마 기본적으로 디폴트 테마가 선택되어 있을 겁니다.

'Current theme'를 선택해 테마 선택창으로 들어 갑니다.

방금 설치된 새로운 테마인 'BMW of kamahn' 테마가 보일겁니다.

선택하시면 되구요 ^^

다음 바로 홈버튼 눌러 나가지 마시고!!!!!

하단 탭중에 가운데 '카테고리' 탭으로 갑니다.

보이는 카테고리는 제가 임의로 설정한 겁니다.

해당 카테고리를 눌러 마음대로 이름을 바꾸셔도 됩니다.

이름을 바꾸셨으면 상단 우측의 'edit'버튼을 눌러줍니다.

(단, 이름을 길게 주면 상대적으로 글자크기가 줄어듭니다. 알아보지 못할정도로... --;;)

그러면 +로 바뀔겁니다. +를 누르면 현재 카테고리 설정이 되지 않은 스프링보드상의 나머지 아이콘들이 나타나게 됩니다.

(전 이미 다 넣었으므로 원래 사용했던 블랙테마의 빈 아이콘들과 카테고리 아이콘 나머지들만 보입니다만... --;;)

카테고리로 넣을 어플 선택과 동시에 바로 목록에서 사라집니다. 해당 카테고리로 들어가버린거지요 ^^

끝났으면 'done'을 눌러 해당 카테고리에서 나오면 조금전에 선택한 아이콘들이 보일 겁니다.

포고플랭크가 지 마음대로(?) 넣어 놓은 아이콘들은 반대로 edit에서 '-' 버튼을 눌러 뺀다음

다시 원하는 카테고리로 들어가 '+'로 넣어주면 됩니다.

그러면 이랬던 아이폰 화면이 ----------------------------> 이렇게 됩니다 ^^

좀 전에 만들었던 카테고리들이 폴더가 되어 휠에 놓여졌습니다.

휠은 시계방향, 반대방향 어디로든 스크롤이 되구요. 총 11개까지 가능합니다.

(더 만드시면 아이콘들이 사라진댑니다 ㄷㄷㄷ)

원하는 폴더를 터치하면 오른쪽 화면처럼 어플 목록이 뜹니다.

저처럼 카테고리 작업을 하셨다면 포고플랭크 설정 어플이 오른쪽 화면처럼 되어 있겠지요 ^^

자~ 일단 기본적인 포고플랭크 설정이 완료 되었습니다.

다음은 배경화면을 위해 보스페이퍼 설정으로 들어가 보겠습니다.

5) 보스페이퍼 설정

배경화면들을 순차변경 해 움직이는 배경으로 설정할 겁니다.

(5-Bosspaper Setup.zip 파일 역시 순서 개념상 빈 문서 압축한 겁니다. 버리세요 ^^;;;)

아이폰에서 조금전에 설치했던 보스페이퍼 어플을 실행합니다.

저는 포고플랭크와 함께 시스템 카테고리에 넣어두었었구요. 실행하면 오른쪽 같은 경고가 나옵니다.

윈터보드의 테마와 충돌 가능성에 대한 언급이구요 ^^ 일단은 신경쓰지 마세요 ^^

맨 위의 버튼을 켜서 활성화 시키시구요. 아래로 스크롤하면 다른 여러가지 설정들이 나타납니다만

제 설정대로 일단은 따라해 보시고 나중에 입맛에 맞게 고치세요 ^^

(저 transition Interval이 그림이 바뀌기 전 머무는 시간인데... 1초면 좋겠는데 5초가 최단이네요 ㅠㅠ)

다음은 바뀔 그림들을 지정해야 합니다.

원래는 폴더째 지정하는 옵션으로 해도 되는 것으로 아는데 이상하게 전 안되더라구요. --;;;

그래서 개별 파일로 다중 선택해 변경시킬 참입니다.

'individual pictures'를 선택하시고 이어 나타나는 폴더타입중에 'wallpaper'를 선택합니다.

이유는 당연하겠지만 아까 월페이퍼 폴더에 그림들을 위치 시켰기 때문입니다. ^^

그러면 아이폰내의 월페이퍼 폴더의 모든 그림들이 나타납니다. 그리고 파일 목록 오른쪽엔 선택버튼들이 있지요.

녹색 'ADD'버튼을 누르면 빨간색 'REM'버튼으로 바뀝니다. REMEMBER의 약자라고 생각이.... --;; 아뉜가... ㅠㅠ

아까 넣은 파일들을 모두 선택합니다.

(bmw-back01.png~bmw-back08.png 까지 다 선택해 줍니다.)

선택이 끝났으면 왼쪽위의 'BACK'버튼을 눌러 이미지 선택 옵션으로 돌아갑니다.

방금 선택된 파일들의 목록이 보이지요. 다시 'BACK'버튼으로 기본 설정화면으로 돌아갑니다.

설정항목 중 아랫쪽에 있는 언더 윈터보드 옵션은 윈터보드의 테마들과의 우선순위를 지정하는 겁니다.

전 그냥 꺼두었습니다. --;;

다 되었으면 아이폰의 홈버튼 누르시고 자동빵 리스프링~

아래와 같은 화면이 보일 겁니다. ^^

짜잔.... 가만히 5초를 기다려 보세요. 시스널 불이 켜지고 윗쪽의 BMW 가이나 컨셉카의 후미등 불도 들어올 겁니다. ^^

자 이번엔 아이폰 하단의 독 테마도 적용해 보겠습니다.

6) 독 테마 설치

BMW테마에 맞게 제작된 독....이고 싶었으니 급한 마음에 일단 지난번 제작한 블랙테마의

독 부분만 테마로 다시 적용할 겁니다 ^^;;;

6-dock theme install.zip파일을 압축해제 하면 테마 폴더가 있습니다.

폴더를 살짝 열어보면...

이런 내용물입니다. 독에 위치한 아이콘들을 바꿀 새로운 아이콘들과 설정 내용 스크립트 파일입니다.

독 배경은 그냥 투명입니다.

그러면 위의 폴더를 통째로 아이폰 테마 폴더에 넣어 윈터보드에서 활성화 시키면 되는 겁니다.

다 또 해봅니다. ^^

아이폰 익스플로러로 다시 가서 BMW Dock.theme 폴더를 이번엔 통째로 넣는 겁니다.

넣을 위치는

root-private-var-stash-themes.?????? 에 드래그 해서 떨궈 주시면 됩니다.

(저 ???가 뭐냐고 물으시는 분들이 계시는데 저 자리 문자가 개인마다 다르기 때문입니다. ^^)

테마 파일을 넣었다고 끝나는게 아닙니다.

윈터보드에서 활성화를 시켜줘야 합니다.

아이폰을 들고 기분좋게 휠을 돌려 시스템을 선택하고 윈터보드를 찾아 열어줍니다. ^^

그리고 윈터보드 목록에서 방금 넣은 BMW Dock을 체크해 줍니다. 아이폰의 홈버튼을 누르면 리스프링~

자~ 이제 독 테마도 변경이 되었군요 ^^

기본적인 인터페이스는 완료 되었습니다. 이젠 아이폰을 처음 열었을때 만나게 될 락스크린도

바꿔야겠지요.

7) 락스크린 테마 설치

bmw락스크린의 기본은 'iLockScreen No Rss2' 테마의 변형 입니다. ^^

배경화면과 숫자파일을 제가 작업해 바꿔놓은 거죠 ^^

7-lockscreen install.zip파일을 압축해제 하시면 다음과 같은 파일이 보입니다.

열어보면 이런 파일들이 있구요. ^^

private폴더를 열면 제가 변형한 파일들이 있습니다.

이 파일들을 기본적으로 바꾸시면 또다른 테마를 만들 수 있는거죠 ^^

(widget1.png파일은 원본 파일에 예비로 있던 겁니다. 지우셔도 됩니다 ^^)

이번에도 'BMW LockScreen No Rss'폴더를 통째로 아이폰 테마폴더로 옮기면 되는 겁니다.

아이폰 익스플로러로 가서 아까 독테마 넣었던 그곳에 넣으시면 됩니다.

root-private-var-stash-themes.?????? <----- 이곳에 넣으세요 ^^

이번에도 윈터보드에서 활성화 시켜줍니다.

체크하고 홈버튼 누르면 리스프링~~~

이렇게 되는 거죠 ^^ ㅋ

8) 락인포 설치 & 설정

제 BMW 테마 첫 그림들 보시면 락스크린에 테마 말고도 문자수신 내용 같은데 뜨는게 보일겁니다.

이미 많은 분들이 사용하고 계시는 락인포 어플을 이용한 테마 입니다.

현재 유료로 전환이 되어 버려 다운이 되는지 어쩌는지 잘 모르겠구요.

전 포고플랭크와 더불어 락인포도 제가 얻은 파일을 첨부합니다.

이것 역시도 누군가 한마디만 해도 바로 삭제될 겁니다. ^^;;;

(단 이게 등록하라는 메세지가 안뜨는 것으로 봐서는 크랙버전이다 믿고 있었는데

플러그인을 설치하니 등록하라고 메세지가 뜨네요 ㅠㅠ 플러그인 괜히 설치했다...ㅠㅠ)

하여간....

8-lockinfo install.zip파일 압축해제 하면 다음과 같은 파일들이 있습니다.

왼쪽은 락인포 어플 설치파일이구요 오른쪽은 이름 그대로 플러그인 파일 입니다

하지만 이 플러그인 파일은 제가 사용해보지 않아서 잘 모릅니다. 할글화 파일이라고 기억되기로 하고...

예전에 맏아 놓은거라 잘 모릅니다만 혹시 몰라 첨부 합니다.

(제가 설정에 사용한 플로그인은 저 파일이 아닙니다. --;;)

포고플랭크와 마찬가지로 락인포 설치도 각자 알아서 해결하시기 바랍니다.

이 부분 만큼은 각자 사용하는 유틸에 따라 방법도 가지가지이고... 전 PC Suite라는 유틸로만 설치를 해서... --;;;

하여간....

설치가 완료되면 새로운 아이콘 뜨는거... 없습니다. --;;;

아이폰의 기본 세팅 어플안에 들어가 있지요.

다시 휠을 돌려 시스템안의 세팅을 열어봅니다.

설정어플을 열면 뭐 기본적인 것만 보이지요? 아래로 주욱~ 스크롤 합니다.

개인이 설치한 어플에 따라 다릅니다만 대충 중간 아래 정도에 있습니다. ^^

반가운 마음에 락인포 설정으로 들어가면 개인에 따라 다음과 같은 메세지가 뜰 수 있습니다. ㅠㅠ

쳇... ㅠㅠ

그렇다고 사용할 수 없는건 아니니 일단 무시하고 설정을 시작 합니다.

먼저 락인포 활성화 하구요~ 아래의 플로그인 설정으로 들어가면.... 각종 나타내어질 정보에 관한 설정항목들이 있습니다.

그리고 전 다른 메세지등의 표시를 위해 get more plugin으로 들어가....

할일 표시 플러그인을 설치했죠. 여기서 그만 등록하라는 메세지가 나타나기 시작을... ㅠㅠ

이부분의 설치 여부는 각자 선택하시기 바랍니다. ^^

설정이 끝났다면 아이폰 홈버튼을 눌러 홈화면으로 나옵니다.

락인포에 관한 설정은 리스프링이 필요 없으므로 아이폰의 상단 버튼을 눌러 잠시 나갔다가

다시 켜시면 (재시동이 아닙니다. ^^;;; 그러실 필요 없습니다 그냥 한번 껐다가 켜시면 됩니다.)

이런 화면이 보이실 겁니다.

몇가지 추가된 정보항목들이 나타납니다. ^^

자 이제 설치가 완료 되었네요 ^^

(기타 제 화면의 status bar의 날씨 옵션등은 테마강좌에 잘 설명되어 있는 다른분들의 글을 참고 하세요 ^^)

여기까지가 제가 만든 BMW Theme 1.4입니다. ^^

일단 1.4를 사용하시다 보면 전화올때 슬라이딩 바가 달라져 있는 부분이나

메시지 입력창, 기타 다른 인터페이스가 미흡한 점등이 보이실 텐데요.

제가 시간이 나는대로 차근차근 수정해 나갈 예정입니다.

아니면 직접 수정하셔도 되겠죠? ^^

정말 긴글 입니다. 읽으시느라 고생 많으셨습니다.

순전히 제글을 스텝 바이 스텝으로 따라 하시는 분들은 제발 천천히 읽어주세요

후닥닥 읽고 하시면 분명히 뭔가 빼먹고 하시게 됩니다. 본인은 분명 했다고 생각하고 사실 설정은 안되어 있고...

그리고 안된다고 답답해 하시고... 저도 그랬거든요.

그리고 테마라는게 개인이 이전에 설치한 여러가지 메타와 환경의 변수로 본인만 안되는 경우도 분명히 있습니다.

이런 경우는 어쩔 수가... ㅠㅠ

하여간 좋은 결과 있으시길... ^^

끝 입니다.~~~ ^^

======================================

BMW With BMW...

경고 :

본 글의 내용과 이미지는 절대 본인의 의도가 아닌이상 상업성,비상업성을 막론하고

그 어느 공간이나 미디어로도 옮겨지거나 복제될 수 없습니다.

출처를 명기한 단순 링크만 허용합니다.

본 테마는 본인이 '1차 소유자'인 순수 저작물입니다.

개인적인 수정은 허용하나 수정된 테마의 공개적인 배포는 금합니다.

karashy works

Lego Star Wars? Hey son! I'll make it for you! - 6-Day Venator Star Destroyer Papercraft Making Record

6-Day Venator Star Destroyer Papercraft Making Record 1. Upper deck works

3. Attach upper deck, side and supporting column

Instruction for TECHNOIR MK1 for iOS4 HD Installation

BMW 테마 1.4 - 아이폰 테마 --> 시디아 BMW Theme of Kamahn

6-Day Venator Star Destroyer Papercraft Making Record

1. Upper deck works