MSU S.A.

Portland Cement

a7mdnour@hotmail.com (ahmdnour) — Sun, 28 Nov 2010 10:56:00 +0000

Portland Cement

SPECIFICATION OF ORDINARY PORTLAND CEMENT 42.5 or 53 – GRADE ASTM C150, TYPE 1 Or BS

TEST AND COMPLIANCE :
PERTICULARS	UNIT	REQUIREMENT OF
		IS 12269 : 1987
A. CHEMICAL REQUIREMENTS :

1. Lime Saturation Factor		0.80 - 1.02
2. Ratio of Percentage of Alumina to
that of Iron Oxide		0.66 Min
3. Insoluble Residue	%	3.00 Max
( percent by mass )
4. Magnesia ( percent by mass )	%	6.00 Max
5. Sulphuric Anhydride (SO3 )	%	3.00 Max
( Percent by mass )
6. Loss On Ignition	%	4.00 Max
7. Chloride ( Percent by mass )	%	0.10 Max

B. PHYSICAL REQUIREMENTS :
1. Fineness ( Blaine )	M2 / Kg	225 Min
2. Soundness
a. Le. Chatelier Expansion	mm	10.00 Max
b. Autoclave Expansion	%	00.8 Max
3. Setting Time
a. Initial	Minutes	30 Min
b. Final	Minutes	600 Max
4. Compressive Strength
a. 72+ 1 hours ( 3 days )	Mpa	27 Min
b. 168 + 1 Hours ( 7 days )	Mpa	37 Min
c. 672 + 4 hours ( 28 days )	Mpa	53 Min

Minimum order: 12,500 Metric Tons

MAZUT 100 GOST –1058575 RUSSIAN ORIGINS

a7mdnour@hotmail.com (ahmdnour) — Sun, 28 Nov 2010 10:38:00 +0000

Specifications COMPONENTS RESULT

1. Ash content 0.14
2. Mass fraction of sulphur, not more % -low – sulphur – residual – oil0.5
3. Temperature of flash not less ?C in the closed crucible
in the open crucible ?C
4. Temperature of solidification, not higher ?C25
5. Kinematics viscosity118 max
6. Water content 0.5%
7. Mechanical Impurities Lower than 0.1%
8. Acidity Lower than 5mg KOH 100ml
9. AlkalinityNil
10. Gross Calorific Value Kcal kg KJ kg Min 9200 41300
11. Density at 15.0 ?C kg 10.8900 – 0.9200
12. Hydrogen Sulphide Content (H2S) pom0.5 max
13. Carbon ResidualLowe that 7%
14. Vanadium (V) ppm23
15. Aluminium (AL) ppm5
16. Silicon (Si) ppm12
17. Nickel (Ni) ppm29
18. Asphaltenes mm 3.6%
19. Distillation @ 4mm Hg Extracted to 760 mm Hg Initial Boiling Point ?C 216
5% recovered ?C 259
10% recovered ?C310
20% recovered ?C 358
30% recovered ?C445
40% recovered ?C502
50% recovered ?C534
60% recovered ?C538
75% recovered ?C545
80% recovered ?C-
90% recovered ?C-
Final Boiling Point Volume 550
Percentage Recovered Volume 78%
Residual Volume 22%
Total Nitrogen mm 0.192%
20. Sodium(Na) ppm 15

Minimum order: 100,000 Metric Tons

Sugar Icumsa 45

a7mdnour@hotmail.com (ahmdnour) — Sun, 28 Nov 2010 10:34:00 +0000

REFINED CANE SUGAR

Origin: Brazil

Icumsa: 45 RBU

Polarization: 99.80% min

Ash content: 0.04% max

Moisture: 0.04% max

Solubility: 100% free flowing

Radiation: normal certified

Color: sparkling white

Packing: 50 kg new jute / polypropylene

Minimum order: 12,500 Metric Tons

RUSSIA D2 GAS OIL GOST 305-82

a7mdnour@hotmail.com (ahmdnour) — Sun, 28 Nov 2010 10:28:00 +0000

SPECIFICATIONS FOR RUSSIAN ORIGIN GASOIL L-0.2-62 (GOST 305-82)

Quality of Gas oil L-0.2-62 shall meet GOST 305-82 including but not limited to the below stated specification:

Cetane number, min 45
Distillation, deg. C - 50% max - 96% (final boiling point), max 280 360
Cinematic viscosity at 20 deg. C, mm2/c, (CSt)3.0-6.0
Total Sulphur, %wt, max 0.2
Mercaptan sulphur, %, max 0.01
Hydrogen Sulphur Abs
Copper strip test Passes
Water-soluble acids and alkalis Abs
Actual gum content, mg/100cm3, max 40
Acidity, mg/100cm3 of gas oil, max. 5
Lodine numbers, g/100g, max. 6
Ash, %, max 0.01
Cokability of 10% residue, max. % 0.20
Filtration coefficient, max 3
Sediments Abs
Water Abs
Density at 20 deg. C, kg/m3, max. 860
Flash point (closed cup), deg. C, min 2
Pour point from March to October (Summer), deg. C, max.-5
Pour point from November to February (Winter), deg. C, max. -10
Cloud point from March to October (Summer), deg. C, max. 0
Cloud point from November to February (Winter), deg. C, max.-5 (*) Summer from

March to October - (PP- 5.0 Deg C) - (CP- 0.0 Deg C)
Winter from November to February - (PP- 10.0 Deg C) - (CP- 5.0 Deg C)

Minimum order: 50,000 Metric Tons

UREA N46% PRILLED

a7mdnour@hotmail.com (ahmdnour) — Sun, 28 Nov 2010 10:16:00 +0000

UREA N46% PRILLED

CIS Countries / Russia (seller's option)

Product: Urea Prilled

Nitrogen: 46% min

Moisture: 0.3% max

Biuret: 1% max

Color: pure white

Granulation: 94%

Cell kernels: 90%

Static resist: 0.7%

Melting point: 132 degrees cent.

Brill: 1-4 mm 90%

Packing: bulk

Free flowing, treated with anti-caking, non-radioactivity, 100% free of harmful substance
Minimum order: 12,500 Metric Tons

Rice

a7mdnour@hotmail.com (ahmdnour) — Sat, 27 Nov 2010 13:56:00 +0000

Rice

THAI RICE
Thai's Long Grain White Rice with specifications as follows:
Specifications of 5% Broken Long Grain Rice:
Red kernels and or under milled kernels not exceeding 2.0% -
Yellow kernels not exceeding 0.5% -
Chalky kernels not exceeding 6.0% -
Damaged kernels not exceeding 0.25% -
White glutinous rice not exceeding 1.5% -
Paddy not exceeding 10 grains per 1 kg. of rice -
Undeveloped kernels, immature kernels, other seeds and foreign matter either singly or combined not exceeding 0.3%
Packing: 50 kg net Rice in new p.p. Bag.
Minimum order: 12,500 Metric Tons

VIETNAMESE LONG GRAIN RICE
Broken kernels: 5% - 25%
Moisture: 14%- 14.5%
Foreign matter: 0.1% - 0.5%
Chalky kernels: 2.5% - 8%
Paddy: 15 sd/kg 30 sd/kg
Red & Red streaked Rice: 0.5% - 5%
Packing: 50 kg net rice in new p.p. Bag.
Minimum order: 12,500 Metric Tons