My Toyota Sienna

Jump Starting a Toyota Sienna

2014-12-08T19:42:00.003-08:00

If your Toyota Sienna will not start First do Simple checks Before JUMP Starting making these checks, make sure you have followed the correct starting procedure and that you have sufficient fuel. If your Toyota Sienna is equipped with the engine immobiliser system, also check whether the other keys will start the engine. If they work, your key may be broken. Have the key checked at your Toyota dealer. If none of your keys work, the system is possibly broken. Call your Toyota Sienna dealer. If the Toyota Sienna engine is not turning over or is turning over too slowly Check that the Toyota Sienna battery terminals are tight and clean. If the battery terminals are O.K., switch on the interior light. If the Toyota Sienna light is out, dim or goes out when the Toyota Sienna starter is cranked, the battery is discharged. You may try jump starting. If the light is O.K., but the engine still will not start, it needs adjustment or repair. Call a Toyota Sienna dealer or qualified Toyota Sienna repair shop. Do not pull-or push-start the Toyota Sienna. It may damage the vehicle or cause a collision when the engine starts. Also the three-way catalytic converter may overheat and become a fire hazard.
If the Toyota Sienna engine turns over at its normal speed but will not start— Check that all the push-on connectors are tight. (For example, connectors at the Toyota Sienna spark plugs, ignition coil and/or distributor) If the connectors are O.K., the Toyota Sienna engine may be flooded because of repeated cranking. Starting a flooded engine” for further instructions. Starting a flooded Toyota Sienna engine If the engine will not start, your engine may be flooded because of repeated cranking. If this happens, turn the Toyota Sienna key to “START” with the accelerator pedal held down. Keep the key and accelerator pedal so for 15 seconds and release them. Then try starting the engine with your foot off the accelerator pedal. If the Toyota Sienna engine does not start after 15 seconds of cranking, release the key, wait a few minutes and try again. If the engine still will not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop for assistance. Do not crank for more than 30 seconds at a time. This may overheat the Toyota Sienna starter and Toyota Sienna wiring systems. Toyota Sienna Jump starting Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your Toyota Sienna or battery, follow the Toyota Sienna jump starting procedures. If in doubt, we strongly recommend that you have a competent technician or towing service jump start your Toyota Sienna. Toyota Sienna EMERGENCY STARTING CAUTION Use only a 12-volt jumper system. You can damage a 12-volt starting motor, Toyota Sienna ignition system, and other electrical parts beyond repair by use of a 24-volt power supply (either two 12-volt batteries in series or a 24-volt motor generator set).WARNING - Battery Keep all flames or sparks away from the battery. The battery produces hydrogen gas which may explode if exposed to flame or sparks. Do not attempt to jump start the Toyota Sienna if the discharged battery frozen or if the electrolyte level low; the battery may rupture or explode. WARNING - Battery Never attempt to check the electrolyte level of he battery as this cause the battery to rupture or explode causing serious injury. Jump starting procedure1. Make sure the Toyota Sienna booster battery is 12-volt and that its negative terminal is grounded. 2. If the booster battery is in another Toyota Sienna, do not allow the Toyota Sienna's to touch.3. Turn off all unnecessary electrical loads.

4. Connect the Toyota Sienna jumper cables in the exact sequence shown in the previous illustration. First connect one end of a jumper cable to the positive terminal of the discharged Toyota Sienna battery (1), then connect the other end to the positive terminal on the booster battery (2). Proceed to connect one end of the other jumper cable to the negative terminal of the booster battery (3), then the other end to a solid, stationary, metallic point (for example, the Toyota Sienna engine lifting bracket)away from the battery (4). Do not connect it to or near any part that moves when the Toyota Sienna engine is cranked. CAUTION - Battery cables Do not connect the jumper cable from the negative terminal of the booster battery to the negative terminal of the discharged battery. This can cause the discharged battery to overheat and crack, releasing battery acid. Do not allow the jumper cables to contact anything except the correct battery terminals or the correct ground. Do not lean over the Toyota Sienna battery when making connections. Start the engine of the Toyota Sienna with the booster battery and let it run at 2,000rpm, then start the engine of the Toyota Sienna with the discharged battery. the cause of your battery discharging is not apparent, you should have your Toyota Sienna checked by an Authorized Toyota Sienna Dealer .Push-starting Toyota Sienna's equipped with automatic transaxle cannot be push-started. jump-starting. CAUTION Never tow a Toyota Sienna to start it because the sudden surge forward when the engine starts could cause a collision with the tow Toyota Sienna.
2. Turn on your Toyota Sienna emergency flashers. 3. Try to start the Toyota Sienna engine again. If your Toyota Sienna will not start, contact an authorized Toyota Sienna dealer or seek other qualified assistance.
Jump Starting a Toyota Sienna

Toyota Sienna Tire Selection and Maintenance

2014-12-06T21:06:00.002-08:00

Toyota Sienna Tire care For proper Toyota Sienna maintenance, safety, and maximum fuel economy, you must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your Toyota Sienna. Recommended cold tire inflation pressures All Toyota Sienna tire pressures (including the spare) should be checked every day when the tires are cold. “Cold Tires” means the Toyota Sienna has not been driven for at least three hours or driven less than 1.6 km (one mile). Recommended pressures must be maintained for the best Toyota Sienna ride, top Toyota Sienna handling, and minimum tire wear. All Toyota Sienna specifications (sizes and pressures) can be found on a label attached to the Toyota Sienna. WARNING - Tire underinflation Severe underinflation (70 kPa (10 psi) or more) can lead to severe heat build-up, causing blowouts, tread separation and other tire failures that can result in the loss of Toyota Sienna control leading to severe injury or death. This risk is much higher on hot days and when driving for protracted periods at high speeds. Underinflation also results in excessive wear, poor Toyota Sienna handling and reduced fuel economy. Wheel deformation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by an Authorized Toyota Dealer Overinflation produces a harsh Toyota Sienna ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards. Warm tires normally exceed recommended cold tire pressures by 28 to 41 kPa (4 to 6 psi). Do not release air fromwarm tires to adjust the pressure or the tires will be underinflated. Be sure to reinstall the tire inflation valve caps. Without the valve cap, dirt or moisture could get into the valve core and cause air leakage. If a valve cap is missing, install a new one as soon as possible. WARNING - Tire Inflation Overinflation or underinflation can reduce tire life, adversely affect Toyota Sienna handling, and lead to sudden tire failure.This could result in loss of Toyota Sienna control and potential injury CAUTION - Tire pressure Always observe the following: Check Toyota Sienna tire pressure when the tires are cold. (After Toyota Sienna has been parked for at least three hours or hasn't been driven more than 1.6 km (one mile) since startup.) Check the pressure of your spare tire each time you check the pressure of other tires. Never overload your Toyota Sienna. Be careful not to overload a Toyota Sienna luggage rack if your Toyota Sienna is equipped with one. Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them Checking tire inflation pressure Check your Toyota Sienna tires once a month or more.Also, check the tire pressure of the spare tire. How to check Use a good quality gage to check tire pressure.You can not tell if your Toyota Sienna tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your Toyota Sienna has been sitting for at least three hours or driven no more than 1.6 km (1 mile). Remove the valve cap from the tire valve stem. Press the tire gage firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the tire and loading Toyota Sienna information label, no further adjustment is necessary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. Tire rotation To equalize tread wear, it is recommended that the tires be rotated every 12,000 km (7,500 miles) or sooner if irregular wear develops.

During rotation, check the tires for correct balance. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pressure, improper wheel alignment, outof- balance Toyota Sienna wheels, severe braking or severe cornering. Look for bumps or bulges in the tread or side of tire. Replace the tire if you find either of these conditions. Replace the tire if fabric or cord is visible. After rotation, be sure to bring the front and rear tire pressures to specification and check Toyota Sienna lug nut tightness. Disc brake pads should be inspected for wear whenever tires are rotated. Rotate radial tires that have anasymmetric tread pattern only from front to rear and not from right to left. WARNING Do not use the compact spare tire for tire rotation Do not mix bias ply and radial ply tires under any circumstances. This may cause unusual handling characteristics that could result in death, severe injury, or property damage. Toyota Sienna Tire replacement If the tire is worn evenly, a tread wear indicator will appear as a solid band across the tread. This shows there is less than 1.6 mm (1/16 inch) of tread left on the tire. Replace the tire when this happens. Do not wait for the band to appear across the entire tread before replacing the Toyota Sienna tire WARNING The Toyota Sienna ABS works by comparing the speed of the wheels.Tire size can affect wheel speed. When replacing tires, all 4 tires must use the same size originally supplied with the Toyota Sienna. Using tires of a different size can cause the Toyota Sienna ABS (Anti-lock Brake System) and ESC (Electronic Stability Control) to work irregularly. Compact spare tire replacement A compact spare tire has a shorter tread life than a regular size tire. Replace it when you can see the tread wear indicator bars on the tire. The replacement compact spare tire should be the same size and design tire as the one provided with your new Toyota and should be mounted on the same compact spare tire wheel. The compact spare tire is not designed to be mounted on a regular size wheel, and the Toyota Sienna compact spare tire wheel is not designed for mounting a regular size tire. Toyota Sienna Wheel replacement When replacing the Toyota Sienna metal wheels for any reason, make sure the new wheels are equivalent to the original Toyota Sienna factory units in diameter, rim width and offset. WARNING A wheel that is not the correct size may adversely affect Toyota Sienna wheel and bearing life, braking and stopping abilities, handling characteristics, ground clearance, body-to-tire clearance, snow chain clearance, speedometer calibration, headlight aim and bumper height. Wheel alignment and tire balance The wheels on your Toyota Sienna were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your Toyota Sienna wheels aligned again. However, if you notice unusual tire wear or your Toyota Sienna pulling one way or the other, the alignment may need to be reset. If you notice your Toyota Sienna vibrating when driving on a smooth road, your wheels may need to be rebalanced. CAUTION Improper wheel weights can damage your Toyota Sienna's aluminum wheels. Use only approved wheel weights. WARNING - Replacing tires Driving on worn-out tires is very hazardous and will reduce braking effectiveness, steering accuracy, and traction. Your Toyota Sienna is equipped with tires designed to provide for safe ride and handling capability. tire and wheel that is different from the one that is originally installed on your Toyota Sienna. It can affect the safety and performance of your Toyota Sienna, which could lead to handling failure or rollover and serious injury. When replacing the tires, be sure to equip all four tires with the tire and wheel of the same size, type, tread, brand and load-carrying capacity. The use of any other tire size or type may seriously affect ride, handling, ground clearance, stopping distance, body to tire clearance, snow tire clearance, and speedometer reliability. It is best to replace all four Toyota Sienna tires at the same time. If that is not possible, or necessary, then replace the two front or two rear tires as a pair. Replacing just one tire can seriously affect your Toyota Sienna’s handling. Toyota Sienna Tire traction Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road. Toyota Sienna Tire maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignement. When you have new tires installed, make sure they are balanced. This will increase Toyota Sienna ride comfort and tire life. Additionally, a tire should always be rebalanced if it is removed from the wheel. Tire sidewall labeling Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

1. Manufacturer or brand name Manufacturer or Brand name is shown. A tire’s sidewall is marked with a tire size designation. You will need this information when selecting replacement tires for your car. The following explains what the letters and numbers in the tire size designation mean. Example tire size designation: (These numbers are provided as an example only; your tire size designator could vary depending on your Toyota Sienna.) P185/65R14 86H P - Applicable Toyota Sienna type (tires marked with the prefix “P’’ are intended for use on passenger cars or light trucks; however, not all tires have this marking). 185 - Tire width in millimeters. 65 - Aspect ratio. The tire’s section height as a percentage of its width. R - Tire construction code (Radial). 14 - Rim diameter in inches. 86 - Load Index, a numerical code associated with the maximum load the tire can carry. H - Speed Rating Symbol. See the speed rating chart in this section for additional information. Wheel size designation Wheels are also marked with important information that you need if you ever have to replace one. The following explains what the letters and numbers in the wheel size designation mean. Example Toyota Sienna wheel size designation: 5.5JX14 5.5 - Rim width in inches. J - Rim contour designation. 14 - Rim diameter in inches Tire speed ratings The chart below lists many of the different speed ratings currently being used for passenger cars. The speed rating is part of the tire size designation on the sidewall of the tire. This symbol corresponds to that tire's designed maximum safe operating speed.S 180 km/h (112 mph) T 190 km/h (118 mph) H 210 km/h (130 mph) V 240 km/h (149 mph) Z Above 240 km/h (149 mph) 3. Checking tire life (TIN : Tire Identification Number) Any tires that are over 6 years, based on the manufacturing date, tire strength and performance, decline with age naturally (even unused spare tires). Therefore, the tires (including the spare tire) should be replaced by new ones. You can find the manufacturing date on the tire sidewall (possibly on the inside of the wheel), displaying the DOT Code. The DOT Code is a series of numbers on a tire consisting of numbers and English letters. The manufacturing date is designated by the last four digits (characters) of the DOT code. DOT : XXXX XXXX OOOO The front part of the DOT means a plant code number, tire size and tread pattern and the last four numbers indicate week and year manufactured. For example: DOT XXXX XXXX 1611 represents that the tire was produced in the 16th week of 2011. WARNING - Tire age Tires degrade over time, even when they are not being used. Regardless of the remaining tread, it is recommended that tires generally be replaced after six (6) years of normal service. Heat caused by hot climates or frequent high loading conditions can accelerate the aging process. Failure to follow this warning can result in sudden tire failure, which could lead to a loss of control and an accident involving serious injury or death. 4. Tire ply composition and material The number of layers or plies of rubber- coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction. 5. Maximum permissible inflation pressure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label for recommended inflation pressure. 6. Toyota Sienna Maximum load rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the Toyota Sienna, always use a tire that has the same load rating as the factory installed tire. 7. Uniform tire quality grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: TREADWEAR 200 TRACTION AA TEMPERATURE A Tread wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one-and-ahalf times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use. However, performance may differ from the norm because of variations in driving habits, service practices and differences in road characteristics and climate. These grades are molded on the side-walls of passenger Toyota Sienna tires. The tires available as standard or optional equipment on Toyota Toyota Siennas may vary with respect to grade. Traction - AA, A, B & C The traction grades, from highest to lowest, are AA, A, B and C. The grades represent the tires ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Temperature -A, B & C The temperature grades are A (the highest), B and C. The grades represent the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tires to degenerate and reduce tires life, and excessive temperature can lead to sudden tires failure. Grades A and B represent higher levels of performance on the laboratory test wheel than the minimum required by the law.Tire temperature The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat build-up and possible sudden tire failure. This can cause loss of Toyota Sienna control and serious injury or death. Tire terminology and definitions Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in kilopascal (kPa) or pounds per square inch (psi). Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kilopascals (kPa) or pounds per square inch (psi) before a tire has built up heat from driving. Curb Weight: This means the weight of a Toyota Sienna with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Toyota Sienna Weight Rating GAWR FRT: Gross Axle Weight Rating for the front Axle. GAWR RR: Gross Axle Weight Rating for the rear axle. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a Toyota Sienna. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Toyota Sienna Weight: The sum of curb weight; accessory weight; Toyota Sienna capacity weight; and production options weight. Normal Occupant Weight: The number of occupants a Toyota Sienna is designed to seat multiplied by 68 kg (150 pounds). Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a particular side that faces outward when mounted on a Toyota Sienna. The outward facing sidewall bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the inner facing sidewall. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose Toyota Siennas. Recommended Inflation Pressure: Toyota Sienna manufacturer's recommended tire inflation pressure and shown on the tire placard. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. Toyota Sienna Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lbs.) plus the rated cargo and luggage load. Toyota Sienna Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Toyota Sienna Normal Load on the Tire: That load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and driving by 2. Toyota Sienna Placard: A label permanently attached to a Toyota Sienna showing the original equipment tire size and recommended inflation pressure. All season tires Toyota specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road conditions. All season tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas. Summer tires Toyota specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rating M+S (Mud and Snow) on the tire side wall. if you plan to operate your Toyota Sienna in snowy or icy conditions. Toyota recommends the use of Toyota Sienna snow tires or all season tires on all four wheels. Snow tires If you equip your Toyota Sienna with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four Toyota Sienna wheels; otherwise, poor handling may result. Snow tires should carry 28 kPa (4 psi) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar, or up to the maximum pressure shown on the tire sidewall, whichever is less. Do not drive faster than 120 km/h (75 mph) when your Toyota Sienna is equipped with snow tires.

My Toyota Sienna Door Handle replacement, Driver's Door

2011-11-13T03:59:00.001-08:00

My Toyota Sienna Driver's Door Handle replacement.

How to replace my Toyota Sienna's Door Handle. Broken Toyota Sienna Door Handle on the Driver's Door.

Remove the Toyota Sienna Driver's Inside Door Panel.

Unclip the Toyota Sienna Door panel electric connectors for the Toyota Sienna power windows and locks panel and the Toyota Sienna Door courtesey light.

To remove my Broken Toyota Sienna Door Handle I accessed the 10mm bolt from behind the inside door panel and accessed the 10mm bolt behind the black cap aft of the door.

Take care not to break the Toyota Sienna Door Latch Pull Rod clips that attached to the Broken Toyota Sienna Door Handle. Remove them by unhugging the clips then rotate.

Remove the Toyota Sienna Door lock mehcanism from the Broken Toyota Sienna Door Handle by removing the 10mm bolt. Fasten the Toyota Sienna Door lock mehcanism to the new Toyota Sienna Driver's Door Handle

Re-attach the Toyota Sienna Door Latch Pull Rods to the new toyota Sienna Door HAndle.

install the new Toyota Sienna Driver's Door Handle using existing 10mm bolts

reconnect the Toyota Sienna Door panel electric connectors for the Toyota Sienna power windows and locks panel and the Toyota Sienna Door courtesey light.

I Replaced the Toyota Sienna Inside Door panel And I Was done

My dog or cat riding in my Toyota Sienna

2011-07-01T04:02:00.001-07:00

My dog or cat riding in my Toyota Sienna
Transporting Pets
Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in a collision.
Transporting Toyota Sienna Pets.
It is extremely dangerous to ride in a cargo area, inside or outside of a Toyota Sienna. In a collision, dogs or cats
riding in these areas are more likely to be seriously injured or killed. Do not allow pets to ride in any area of your
Toyota Sienna that is not equipped with seats and seat belts. Be sure everyone in your Toyota Sienna is in a seat and
using a seat belt properly.
Lock Your Toyota Sienna, never leave your pet in your Toyota Sienna unattended. before traveling with your dog or cat Always remove the key from the ignition and lock all doors when leaving the Toyota Sienna unattended, even in your own driveway or garage. Try to park your Toyota Sienna in a
well-lit area and never invite theft by leaving articles of value exposed. Exhaust Gas Whenever a change is noticed in the sound of the exhaust
system, when exhaust fumes can be detected inside the Toyota Sienna, or when the underside or rear of the Toyota Sienna is
damaged, have a competent mechanic inspect the complete Toyota Sienna exhaust system and adjacent body areas for broken,
damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes
to seep into the passenger compartment. In addition, inspect the exhaust system each time the Toyota Sienna is raised
for lubrication or oil change. Replace as required.If you are required to drive with the trunk open, make sure that all windows are closed and the
climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. Do not run the engine in a closed garage or in confined
areas any longer than needed to move your Toyota Sienna in or out of the area when traveling with your dog or cat.
If it is necessary to sit in a parked Toyota Sienna with the engine running, adjust your heating or cooling controls to force
outside air into the Toyota Sienna. Set the blower at high speed. The best protection against carbon monoxide entry into
the Toyota Sienna body is a properly maintained engine exhaust system.
Safety Checks You Should Make Inside The Toyota Sienna before traveling with your dog or cat.
dog or cat.Seat Belts
Inspect the belt system before traveling with your dog or cat, checking for cuts, frays, and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a
collision.
Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn
webbing, etc. If there is any question regarding belt or retractor condition, replace the belt.
Airbag Warning Light
The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first
turned ON. If the light is not lit during starting, see your authorized Toyota Sienna dealer. If the light stays on, flickers, or comes
on while driving, have the system checked by an authorizedToyota Sienna dealer.
Periodic Safety Checks You Should Make Outside The Toyota Sienna before traveling with your dog or cat.
Toyota Sienna Tires
Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects
lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness.
Check the tires (including spare) for proper pressure. Toyota Sienna Lights
Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
Toyota Sienna Door Latches, before traveling with your dog or cat Check for positive closing, latching, and locking.
Toyota Sienna Fluid Leaks
Check area under Toyota Sienna after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline
fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be
located and corrected before traveling with your dog or cat.
Pet Seatbelts, dog seatbelt, cat seatbelt.

Toyota Sienna Alternator Belt

2011-06-05T12:41:00.000-07:00

Replaceing a Toyota Sienna Alternator Belt, Regulator belt, Serpintine belt, Air compressor Belt. what ever you want to call it. Make sure the Toyota sienna is not running and is cooled off. After the Toyota Sienna has not been operated in two hours.

First clear out the old belt and any fragments that may be lodged. Then Losen the outboard side 14 mm bolt at the pivot of the Alternator. just losen do not remove.

Losen the 12 mm set screw on the jack screw assembly below the alternator housing.

Losen the 12 mm Jack Screw lowering the alternator (regulator). Slide the New Belt over the Toyota sienna Air compressor pulley and up over the Toyota sienna Alternator Pulley. If there is not enough slack in the New Toyota Sienna Alternator Belt then losen the Jack Screw more until you can slide the belt over all pullleys.

Tighten the Toyota Sienna alternator belt by tightining the Jack Screw. once it is taut like a tiger clear all your tools and debri before cranking the Toyota sienna and letting the alternator belt seat in. Then switch off the Toyota sienna and make sure the belt is tight to specifications. if so tighten the Set screw.

Re tighten the 14 mm bolt at the pivot of the Alternator.

My Toyota Sienna Overheating

2011-06-01T08:02:00.000-07:00

Toyota Sienna engine Cooling System. The Cooling System allows the Toyota Sienna engine to maintain the correct working temperature.

Toyota Sienna Heater and radiator hoses, and other Toyota Sienna engine parts, can be very hot. Do not touch them. If you do, you can be burned.
Do not run the Toyota Sienna engine if there is a leak. If you run the Toyota Sienna engine, it could lose all coolant. That could
cause an Toyota Sienna engine fire, and you could be burned. Get any leak fixed before you drive the Toyota Sienna.

The Toyota Sienna has an indicator to warn of Toyota Sienna engine overheating.
There is an Toyota Sienna engine coolant temperature warning light on your Toyota Sienna’s instrument panel. If an Toyota Sienna engine overheat warning is displayed but no steam
can be seen or heard, the problem may not be too serious. Sometimes the Toyota Sienna engine can get a little too hot
when the Toyota Sienna:
Climbs a long hill on a hot day. Stops after high-speed driving.
Idles for long periods in traffic.
If the overheat warning is displayed with no sign of steam:
Turn the air conditioning off.
Turn the heater on to the highest temperature and to the highest fan speed. Open the windows as necessary.
In heavy traffic, let the Toyota Sienna engine idle in N (Neutral)
while stopped. If it is safe to do so, pull off the road, shift to P (Park) or N (Neutral) and let the Toyota Sienna engine idle.
If the temperature overheat gage is no longer in the overheat zone or an overheat warning no longer
displays, the Toyota Sienna can be driven. Continue to drive the Toyota Sienna slow for about 10 minutes. Keep a safe
Toyota Sienna distance from the car in front of you. If the warning does not come back on, continue to drive normally.
If the warning continues, pull over, stop, and park the Toyota Sienna right away. If there is no sign of steam, idle the Toyota Sienna engine for three
minutes while parked. If the warning is still displayed, turn off the Toyota Sienna engine until it cools down.
You may decide not to lift the hood when this warning appears, but instead get service help right away.

If you do decide to lift the hood, make sure the Toyota Sienna is parked on a level surface.
Then check to see if the Toyota Sienna engine cooling fan is running. If the Toyota Sienna engine is overheating, the fan should be running.
If not, do not continue to run the Toyota Sienna engine and have the Toyota Sienna serviced.

When working near the Toyota sienna radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position. The fan is temperature controlled and can start at any time the
ignition switch is in the ON position. An electric Toyota Sienna engine cooling fan under the hood can start up even when the Toyota Sienna engine is not running and can cause injury. Keep hands, clothing, and tools
away from any underhood electric fan. You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the
hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the Toyota Sienna radiator is hot.

Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The Toyota Sienna’s coolant warning system
is set for the proper coolant mixture. With plain water or the wrong mixture, the Toyota Sienna engine could get too hot but you would not get the overheat warning. The Toyota Sienna engine could catch fire and you or
others could be burned. Check Toyota Sienna engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rubber,
cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the Toyota Sienna engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of
coolant from the radiator drain cock. If the cap is sealing properly, the Toyota Sienna engine coolant (antifreeze) will begin todrain from the coolant recovery bottle. DO NOT REMOVE
THE Toyota Sienna COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.
Cooling System — Drain, Flush, and Refill
The system should be drained, flushed, and refilled at the intervals If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling
system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Coolant and Fluids, Lubricants, and Genuine Toyota Sienna Parts”

Mixing of coolants other than specified Toyota Sienna engine coolants, may result in Toyota Sienna engine damage and
may decrease corrosion protection. Do not use plain water alone or alcohol-based
Toyota Sienna engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as
they may not be compatible with the radiator Toyota Sienna engine coolant and may plug the radiator.
This Toyota Sienna has not been designed for use with Toyota Sienna coolants.
Adding Toyota Sienna Coolant
Your Toyota Sienna has been built with an improved Toyota Sienna engine coolant Toyota Sienna Antifreeze/Coolant 5 Year/100,000 Mile Formula
Use only high purity water such as distilled or deionized water when mixing the water/Toyota Sienna engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the Toyota Sienna engine
cooling system.
it is the owner’s responsibility to maintain the proper level of protection against freezing according
to the temperatures occurring in the area where the Toyota Sienna is operated. Mixing coolant types will decrease the life of the Toyota Sienna engine coolant and will require more frequent coolant changes.
Toyota Sienna Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant and to ensure that coolant will return to the radiator from the coolant recovery bottle.

The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
The warning words “DO NOT OPEN HOT” on the Toyota Sienna cooling system pressure cap are a safety precaution.
Never add coolant when the Toyota Sienna engine is overheated. Do not loosen or remove the cap to
cool an overheated Toyota Sienna engine. Heat causes pressure to build up in the cooling system. To prevent scalding
or injury, do not remove the pressure cap while the system is hot or under pressure. Do not use a pressure cap other than the one
specified for your Toyota Sienna. Personal injury or Toyota Sienna engine damage may result.
Disposal of Used Coolant
Used Toyota Sienna engine coolant requiring proper disposal. Check with your local authorities to determine the disposal rules for your
community. To prevent ingestion by animals or children, do not store Toyota Sienna engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician
immediately. Clean up any ground spills immediately.
Coolant Level
The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the
Toyota Sienna engine OFF and cold, the level of the coolant in the bottle should be between the ranges indicated on the bottle.

The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for
Toyota Sienna coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the Toyota Sienna engine operating
temperature is satisfactory, the coolant bottle need only be checked once a month. When additional coolant is needed to maintain the
proper level, it should be added to the coolant bottle. Do not overfill. When the Toyota Sienna is stopped after a few miles of operation, you may observe vapor coming
from the front of the Toyota Sienna engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to
enter the Toyota Sienna radiator. if your Toyota Sienna engine compartment shows no evidence of radiator or hose leaks, the Toyota Sienna may be
safely driven. The vapor will soon dissipate. Do not overfill the coolant recovery bottle. Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be
added, contents of coolant recovery bottle must also be protected against freezing. If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when
the Toyota Sienna engine cools, the cooling system should be pressure tested for leaks. Maintain coolant concentration at 50% Toyota Sienna engine coolant (minimum) and distilled water for proper
corrosion protection of your Toyota Sienna engine, which contains aluminum components.

Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. Keep the front of the radiator clean. If your Toyota Sienna is equipped with air conditioning, keep the front of the
condenser clean, also. Do not change the Toyota Sienna thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type Toyota Sienna thermostat. Other designs may
result in unsatisfactory coolant performance, poor Toyota Sienna gas mileage, and increased emissions.

Toyota Sienna Cold Weather Starting

2011-01-16T04:58:00.001-08:00

Toyota Sienna Cold Weather Starting
Extremely Cold Weather (Below 19°F) To ensure reliable starting at these temperatures, use of
an externally powered electric Toyota Sienna engine block heater (available from your authorized Toyota Sienna dealer) is recommended.

Toyota Sienna engine Toyota Sienna coolant Heater
The Toyota Sienna engine Toyota Sienna coolant heater, if available, can help in cold weather
conditions at or below 0°F for easier starting and better fuel
economy during Toyota Sienna engine warm-up. Plug in the Toyota Sienna coolant heater at least
four hours before starting your Toyota Sienna. An internal thermostat in the
plug-end of the cord will prevent Toyota Sienna engine Toyota Sienna coolant heater operation at
temperatures above 0°F .
To Use The Toyota Sienna engine Toyota Sienna coolant
Heater
1. Turn off the Toyota Sienna engine.
2. Open the hood and unwrap the
electrical cord.
The electrical cord is located on
the driver side of the Toyota Sienna engine
compartment, behind the
air cleaner for V8 models.
The electrical cord is located
on the passenger side of
the Toyota Sienna engine compartment, behind
the Toyota Sienna engine compartment fuse
block for V6 models.
3. Plug it into a normal, grounded
110-volt AC outlet.Plugging the cord into an
ungrounded outlet could cause an
electrical shock. Also, the wrong
kind of extension cord could
overheat and cause a fire. You
could be seriously injured. Plug
the cord into a properly grounded
three-prong 110-volt AC outlet.
The length of time the heater should
remain plugged in depends on
several factors. Ask a Toyota Sienna dealer/retailer
in the area where you will be
parking the Toyota Sienna for the best
advice on this.If the cord will not reach, use a
heavy-duty three-prong extension
cord rated for at least 15 amps.Before starting the Toyota Sienna engine, be
sure to unplug and store the
cord as it was before to keep
it away from moving Toyota Sienna engine
parts. If you do not it could be
damaged.

Automatic Transmission
The shift lever must be in the NEUTRAL or PARK
position before you can start the Toyota Sienna engine. Apply the brakes
before shifting into any driving gear.
If the Toyota Sienna engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather” procedures,
it may be flooded. To clear any excess fuel, push
the accelerator pedal all the way to the floor and hold it.
Then, turn the ignition switch to the START position and
release it as soon as the starter engages. The starter motor
will disengage automatically in 10 seconds. Once this
occurs, release the accelerator pedal, turn the ignition
switch to the LOCK position, wait 10 to 15 seconds, then
repeat the normal starting procedure.

If the Toyota Sienna engine does not start after
5-10 seconds, especially in very cold weather (below 0°F
or -18°C), it could be flooded with too much gasoline. Push the
accelerator pedal all the way to the floor and holding it there as
you hold the key in START for a maximum of 15 seconds.If the Toyota Sienna engine does not start after
5-10 seconds, especially in very cold weather (below 0°F
or -18°C), it could be flooded with too much gasoline. Push the
accelerator pedal all the way to the floor and holding it there as
you hold the key in START for a maximum of 15 seconds.

Normal Starting of either a cold or a warm
Toyota Sienna engine is obtained without pumping or depressing the
accelerator pedal.
Do not press the accelerator. Use the Fob with Integrated
Key to briefly turn the ignition switch to the START
position and release it as soon as the starter engages. The
starter motor will continue to run, and it will disengage
automatically when the Toyota Sienna engine is running. If the Toyota Sienna engine
fails to start, the starter will disengage automatically in 10
seconds. If this occurs, turn the ignition switch to the
LOCK position, wait 10 to 15 seconds, then repeat the
normal starting procedure.

Never pour fuel or other flammable liquids into
the throttle body air inlet opening in an attempt
to start the Toyota Sienna. This could result in a flash
fire causing serious personal injury.
Do not attempt to push or tow your Toyota Sienna to
get it started. Toyota Siennas equipped with an automatic
transmission cannot be started this way.
Unburned fuel could enter the catalytic converter
and once the Toyota Sienna engine has started, ignite
and damage the converter and Toyota Sienna. If the
Toyota Sienna has a discharged battery, booster cables
may be used to obtain a start from a booster
battery or the battery in another Toyota Sienna. This
type of start can be dangerous if done improperly.

Toyota Sienna engine heater

Does my Toyota Sienna have Airbags?

2011-01-01T23:44:00.000-08:00

When Should an Airbag Inflate in my Toyota Sienna?

Frontal airbags are designed to inflate in moderate to severe frontal
or near-frontal crashes to help reduce the potential for severe
injuries mainly to the driver’s or right front passenger’s head and chest.
However, they are only designed to inflate if the impact exceeds a
predetermined deployment threshold. Deployment thresholds
are used to predict how severe a crash is likely to be in time for the
airbags to inflate and help restrain the Toyota Sienna occupants.
Whether the frontal airbags will or should deploy is not based on
how fast your Toyota Sienna is traveling. It depends largely on what you hit,
the direction of the impact, and how quickly your Toyota Sienna slows down.
Frontal airbags may inflate at different crash speeds. For example:
If the Toyota Sienna hits a stationary object, the airbags could inflate at
a different crash speed than if the Toyota Sienna hits a moving object.
If the Toyota Sienna hits an object that deforms, the airbags could inflate
at a different crash speed than if the Toyota Sienna hits an object that
does not deform. If the Toyota Sienna hits a narrow object
(like a pole), the airbags could inflate at a different crash speed
than if the Toyota Sienna hits a wide object (like a wall).
If the Toyota Sienna goes into an object at an angle, the airbags could
inflate at a different crash speed than if the Toyota Sienna goes straight
into the object. Thresholds can also vary with specific Toyota Sienna design.

All of the airbags in the Toyota Sienna will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening.
For frontal airbags, the word
AIRBAG will appear on the middle part of the steering wheel for
the driver and on the instrument
panel for the right front passenger.
With seat-mounted side impact airbags, the word AIRBAG will appear on the side of the
seatback closest to the door.
With roof-rail airbags, the word
AIRBAG will appear along the headliner or trim.
Airbags are designed to supplement
the protection provided by safety
belts. Even though today’s airbags
are also designed to help reduce
the risk of injury from the force of an
inflating bag, all airbags must
inflate very quickly to do their job.

Here are some important things to know about the airbag system:

You can be severely injured or
killed in a crash if you are not
wearing your safety belt — even
if you have airbags. Airbags are
designed to work with safety belts, but do not replace them.
Also, airbags are not designed to
deploy in every Toyota Sienna crash. In some
crashes safety belts are your only
restraint. Wearing your safety belt during a
crash helps reduce your chance
of hitting things inside the Toyota Sienna
or being ejected from it. Airbags
are “supplemental restraints” to
the safety belts. Everyone in your
Toyota Sienna should wear a safety belt
properly — whether or not there is
an airbag for that person.

A frontal Toyota Sienna collision that is not severe enough to need airbag protection will not activate the system. This
does not mean something is wrong with the airbag system.
If you do have a collision in your Toyota Sienna which deploys the airbags, any or all of the following may occur:
The nylon airbag material may sometimes cause abrasions
and/or skin reddening to the driver and front
passenger as the airbags deploy and unfold. The
abrasions are similar to friction rope burns or those
you might get sliding along a carpet or gymnasium
floor. They are not caused by contact with chemicals.
They are not permanent and normally heal quickly.
However, if you haven’t healed significantly within a
few days, or if you have any blistering, see your doctor immediately.
As the airbags deflate you may see some smoke-like
particles. The particles are a normal by-product of the
process that generates the nontoxic gas used for airbag
inflation. These airborne particles may irritate the skin,
eyes, nose, or throat. If you have skin or eye irritation,
rinse the area with cool water. For nose or throat
irritation, move to fresh air. If the irritation continues,
see your doctor. If these particles settle on your
clothing, follow the garment manufacturer’s instructions for cleaning.
It is not advisable to drive your Toyota Sienna after the
airbags have deployed. If you are involved in another
collision, the airbags will not be in place to protect you.

WARNING!
Modifications to any part of the airbag system could cause it to fail
when you need it. You could be injured if the airbag system is not
there to protect you. Do not modify the components or wiring,
including adding any kind of badges or stickers to the steering wheel
hub trim cover or the upper right side of the instrument panel. Do not
modify the front bumper or Toyota Sienna body structure.
Do not attempt to modify any part of your advanced airbag system.
The airbag may inflate accidentally or may not function properly if
modifications are made. Take your Toyota Sienna to an authorized dealer for
any advanced airbag system service. If your seat including your trim
cover and cushion needs to be serviced in any way (including removal
or loosening/tightening of seat attachment bolts), take the Toyota Sienna to
your authorized dealer. Only manufacturer approved seat accessories
may be used. If it is necessary to modify an advanced airbag system
for persons with disabilities, contact your authorized Toyota Sienna dealer.
Do not place or hang any items such as add-on video players on the
right front passenger seat back. The additional weight may cause the
Occupant Classification System to be unable to correctly classify the
right front occupant. This could allow the passenger frontal airbag to
inflate when it is not desired.
You need proper knee impact protection in a collision. Do not mount
or locate any aftermarket equipment on or behind the knee bolsters.
It is dangerous to try to repair any part of the airbag system yourself. Be
sure to tell anyone who works on your Toyota Sienna that it has an airbag system.

Airbags inflate with great force,
faster than the blink of an eye. Anyone who is up against, or very
close to, any airbag when it inflates can be seriously injured or killed.
Do not sit unnecessarily close to the airbag, as you would be if you
were sitting on the edge of your seat or leaning forward. Safety
belts help keep you in position before and during a crash. Always
wear your safety belt, even with airbags. The Toyota Sienna driver should sit as far
back as possible while still maintaining control of the Toyota Sienna.
Occupants should not lean on or sleep against the door or side
windows in seating positions with seat-mounted side impact airbags
and/or roof-rail airbags.
CAUTION
Children who are up against, or
very close to, any airbag when it
inflates can be seriously injured or
killed. Airbags plus lap-shoulder
belts offer protection for adults
and older children, but not for
young children and infants.
Neither the Toyota Sienna’s safety belt
system nor its airbag system is
designed for them. Young children
and infants need the protection
that a child restraint system can
provide. Always secure children
properly in your Toyota Sienna.

Does my Toyota Sienna have Airbags?
.

Spare Tire Carrier Cable Corrosion

2010-12-07T17:13:00.000-08:00

Certain 1998 thr 2010 Toyota Sienna's equiped with spare tire may have severe corrosion of spare tire carrier cable.

Toyota Sienna Owner,

Toyota Special Service Campain on Certain Toyota Siennas.

The Condition may occour if the Toyota Sienna is operated in cold climate regions of the United States where road salts are frequently used. Water can splash backwards with high concentrations of road salt and corrode the spare tire carrier assembly.

The Toyota special service campain offers to apply a corrosion resistant compond to the end of the toyota sienna spare tire carrier cable.

How to take advantage of this Toyota Sienna special service campaign. If you believe your vehicle will be operated in cold climates where a high concentration of road salt is frequently used, please contact an authorized Toyota Sienna dealer and schedule an appointment to have the corrosion resistant compound applied to the end of your Toyota Sienna's spare tire carrier cable. The application of the CRC will take approximately 30 minutes.

This special service campaign applies to 1998 through 2010 model year two-wheel drive Toyota Siennas.

toyota sienna spare tire holder cable.

My Toyota Sienna in Blizzard Conditions

2010-11-26T04:19:00.000-08:00

Toyota Sienna Winter Driving in Blizzard Conditions

You should have some type of winter survival kit and Plan in your Toyota Sienna in case of winter time emergency.

Driving ypur Toyota Sienna on Snow or Ice
Drive carefully when there is snow
or ice between the tires and the road,
creating less traction or grip. Wet ice
can occur at about 32°F (0°C) when
freezing rain begins to fall, resulting
in even less traction. Avoid driving on
wet ice or in freezing rain until roads
can be treated with salt or sand.
Drive with caution, whatever the
condition. Accelerate gently
so traction is not lost. Accelerating
too quickly causes the wheels
to spin and makes the surface under
the tires slick, so there is even
less traction.

Try not to break the fragile traction.
If you accelerate too fast, the drive
wheels will spin and polish the
surface under the tires even more.
The Antilock Brake System (ABS)
improves Toyota Sienna
stability during hard stops on
a slippery roads, but apply the
brakes sooner than when on
dry pavement.
Allow greater following distance on
any slippery road and watch for
slippery spots. Icy patches
can occur on otherwise clear roads
in shaded areas. The surface of
a curve or an overpass can remain
icy when the surrounding roads
are clear. Avoid sudden steering
maneuvers and braking while on ice.
Turn off cruise control, if equipped,
on slippery surfaces.

Blizzard Conditions:

Being stuck in snow can be a serious situation. You should have some type of survival kit in your Toyota Sienna if you Live where blizzard conditions exist. Plan for the worst and hope for the best.

Stay with the
Toyota Sienna unless there is help nearby.
To get help and keep everyone in the Toyota Sienna safe:
Turn on the Hazard Warning Flashers
Tie a red cloth to an outside mirror.

Snow can trap Toyota Sienna engine exhaust
under the Toyota Sienna. This may cause
exhaust gases to get inside.
Toyota Sienna engine exhaust contains carbon
monoxide (CO) which cannot be
seen or smelled. It can cause
unconsciousness and even death.
If the Toyota Sienna is stuck in the snow:
Clear away snow from
around the base of your
Toyota Sienna, especially any that is
blocking the exhaust pipe.
Check again from time to
time to be sure snow does
not collect there.

Open a window about
two inches on the side of the
Toyota Sienna that is away from the
wind to bring in fresh air.

Fully open the air outlets on
or under the instrument panel.

Adjust the Toyota Sienna Climate Control
system to a setting that
circulates the air inside the
Toyota Sienna and set the fan speed
to the highest setting.

Snow can trap exhaust gases
under your Toyota Sienna. This can cause
deadly CO (carbon monoxide) gas
to get inside. CO could overcome
you and kill you. You cannot see it
or smell it, so you might not know it
is in your Toyota Sienna. Clear away snow
from around the base of your
Toyota Sienna, especially any that is
blocking the exhaust

Run the Toyota Sienna engine for short periods
only as needed to keep warm,
but be careful.
To save fuel, run the Toyota Sienna engine for only
short periods as needed to warm
the Toyota Sienna and then shut the Toyota Sienna engine
off and close the window most of
the way to save heat. Repeat
this until help arrives but only when
you feel really uncomfortable
from the cold. Moving about to keep
warm also helps.
If it takes some time for help to
arrive, now and then when you run
the Toyota Sienna engine, push the accelerator
pedal slightly so the Toyota Sienna engine
runs faster than the idle speed. This
keeps the Toyota Sienna battery charged to
restart the Toyota Sienna and to signal for
help with the Toyota Sienna headlamps. Do
this as little as possible to save fuel.

Driving My Toyota Sienna in winter

2010-11-14T03:43:00.001-08:00

DRIVING My Toyota Sienna ON SLIPPERY SURFACES
Acceleration
Rapid acceleration on snow covered, wet, or other slippery
surfaces may cause the front wheels to pull erratically
to the right or left. This phenomenon occurs when
there is a difference in the surface traction under the front
(driving) wheels, particularly with high output engines.
Rapid acceleration on slippery surfaces is dangerous.
Unequal traction can cause sudden pulling of
the front wheels. You could lose control of the
Toyota Sienna and possibly have an accident. Accelerate
slowly and carefully whenever there is likely to be
poor traction (ice, snow,
Traction
When driving on wet or slushy roads, it is possible for a
wedge of water to build up between the Toyota Sienna tire and road
surface. This is hydroplaning and may cause partial or
complete loss of Toyota Sienna control and stopping ability. To
reduce this possibility, the following precautions should
be observed:
1. Slow down during rainstorms or when roads are slushy.
2. Slow down if road has standing water or puddles.
3. Replace Toyota Sienna tires when tread wear indicators first become visible.
4. Keep Toyota Sienna tires properly inflated.
5. Maintain enough distance between your Toyota Sienna and the Toyota Sienna in front of you to avoid a collision in a sudden stop.
FREEING A STUCK Toyota Sienna
If your Toyota Sienna becomes stuck in mud, sand or snow, it
can often be moved by a rocking motion. Turn your
steering wheel right and left to clear the area around the
front wheels. Then shift back and forth between Reverse
and First gear. Usually the least accelerator pedal pressure
to maintain the rocking motion without spinning the
wheels is most effective.
Fast spinning Toyota Sienna tires can be dangerous. Forces generated
by excessive wheel speeds may cause Toyota Sienna tire damage
or failure. A Toyota Sienna tire could explode and injure
someone. Do not spin your Toyota Sienna’s wheels faster
than 35 mph (55km/h) when you are stuck. And don’t
let anyone near a spinning wheel, no matter what the
speed.
Racing the Toyota Sienna engine or spinning the Toyota Sienna wheels too fast
may lead to Toyota Sienna transaxle overheating and failure. It can
also damage the Toyota Sienna tires. Do not spin the Toyota Sienna wheels above
35 mph (55km/h).
Toyota Sienna Snow tires
Some areas of the country require the use of Toyota Sienna snow tires
during winter. Standard Toyota Sienna tires are of the all season type
and satisfy this requirement as indicated by the M+S
designation on the Toyota Sienna tire side wall.
If you need snow tires, select Toyota Sienna tires equivalent in size and
type to the original equipment Toyota Sienna tires. Use snow tires on Toyota Sienna only
in sets of 4, failure to do so may adversely affect the
safety and handling of your Toyota Sienna.
Snow tires generally have lower speed ratings than what
was originally equipped with your Toyota Sienna and should
not be operated at sustained speeds over 75 mph (120
km/h).
To avoid damage to your Toyota Sienna or Toyota Sienna tires, observe the following precautions:
Because of restricted chain clearance between Toyota Sienna tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the Toyota Sienna immediately if noise occurs that
could indicate chain breakage. Remove the damaged parts of the chain before further use. Install chains on the front wheels as tightly as
possible and then retighten after driving about 1⁄2 mile (0.8 km). Do not exceed 45 mph (70 km/h). Drive cautiously and avoid severe turns and large bumps, especially with a loaded Toyota Sienna. Do not drive for prolonged period on dry pavement. Observe the Toyota Sienna tire chain manufacturer’s instructions
on the method of installation, operating speed, and conditions for use. Always use the lower suggested operating speed of the chain manufacturer
if different than the speed recommended by the Toyota Sienna manufacture.

Toyota Sienna, snow tires, winter driving

My Toyota Sienna Replacement Door Handles

2010-11-06T14:26:00.000-07:00

I decided to replace my own Toyota Sienna Rear Side Door Handle (Driver Side).

Broken Toyota Sienna Rear Side Door Handle.

Remove Toyota Sienna Rear inSide Door panel by removing 10mm / Phillips Head Screw from inside Toyota Sienna Rear Side Door cup holder. toyota sienna inside door panels are held on by plastic clip things that can somtimes break. use caustion when popping off your toyota sienna inside door panel.

Remove two (2) 10mm screws holding the broken Toyota Sienna Rear Side Door Handle. i used my awsome craftsmen tool set.

Line up your new Toyota Sienna Rear Side Door Handle, attach door latch cable. Re-use 10mm screws to attach the new Toyota Sienna Rear Side Door Handle.

Then pop the toyota sienna inside door panel back on being careful to line up the toyota sienna inside door panel clips. and as Patrick from Spongebob Squarepants says, "Were Done!"

Here is weere I ordered my Toyota Sienna Rear Side Door Handle.
Hello You sent a payment of $46.18 USD to Auto Parts Network (accounting@usautoparts.com)
Merchant
Auto Parts Network

accounting@usautoparts.com

888-872-8866
Description: Toyota Sienna Rear Side Door Handle
Unit priceQtyAmount
$46.18 USD1$46.18 USD
Subtotal$46.18 USD
Total$46.18 USD
Payment$46.18 USD

Payment sent to accounting@usautoparts.com

My next Toyota sienna door replacement handle will be purchased from amazon

I need a toyota sienna inside front door handle and Toyota front drivers side exterior door handle

My Toyota Sienna Window Fogging

2010-10-23T03:35:00.000-07:00

My Toyota Sienna air conditioning

Toyota Sienna Window Fogging
Interior fogging on the windshield can be quickly removed
by turning the mode selector to Defrost. The
Defrost/Floor mode can be used to maintain a clear
windshield and provide sufficient heating. If side window
fogging becomes a problem increase blower speed.
Toyota Sienna windows tend to fog on the inside in mild but
rainy or humid weather.

The Toyota Sienna electric Rear Window Defroster Control is
located on the climate control. Press this button to
turn on the rear window defroster. A light above the
button will illuminate when the rear window defroster is
ON. The defroster automatically turns off after approximately
15 minutes of operation for the first push of the
button, and will turn off after approximately 8 minutes
for the second push of the button.

Outside Air Intake
When operating the system, particularly during the winter
months, make sure the air intake, at the right side of
the hood, is free of ice, slush, snow, or other obstructions
such as leaves. Leaves collected in the air-intake plenum
may reduce airflow and plug the plenum water drains.

Toyota Sienna Control Setting Suggestions for Various Weather Conditions

Slight changes in your Toyota Sienna engine speed or power may be noticed
when the compressor is on. This is a normal occurrence
since the compressor will cycle on and off to maintain
comfort and increase fuel economy.
NOTE: If your air conditioning performance seems
lower than expected, check the front of the A/C condenser
for an accumulation of dirt or insects.

Recirculation Control
Air is recirculated inside the Toyota Sienna. You
may choose between Bi-Level and Panel air
outlets while in this mode. Use this mode to
temporarily block out any outside odors,
smoke, or dust and to cool the interior rapidly upon
initial start up in very hot or humid weather.

Toyota Sienna CLIMATE CONTROLS
The Air Conditioning and Heating System is designed to
make you comfortable in all types of weather.

Toyota Sienna Defog Air is directed to the
windshield, floor outlets, and
side window vents. Use this mode
to clear the windows of fog or
moisture and warm the passengers.

Toyota Sienna Defrost Air is directed to
the windshield, with some air
directed to the side window vents.
Use this mode to quickly remove fog
or frost from the windshield.
When defrost is selected, the Toyota Sienna air
conditioning turns on automatically to
improve defrosting performance. In
this mode the air conditioning cannot
be turned off and the recirculation
mode cannot be turned on.

Your Toyota Sienna Safety Belts

2010-10-09T05:06:00.001-07:00

Questions and Answers About your Toyota Sienna Safety Belts
Q: Will I be trapped in my Toyota Sienna after a crash if I am wearing a
safety belt?

A: You could be — whether you are wearing a safety belt or not. But
your chance of being conscious
during and after an accident, so you can unbuckle and get out, is
much greater if you are belted.
And you can unbuckle a safety belt, even if you are upside down.

Q: If my Toyota Sienna has airbags, why should I have to wear safety belts?

A: Airbags are supplemental systems only; so they work with
safety belts—not instead of them. Whether or not an airbag is provided, all occupants still have
to buckle up to get the most
protection. That is true not only in frontal collisions, but especially in
side and other collisions.

Q: If I am a good driver, and I never drive far from home,
why should I wear safety belts?

A: You may be an excellent driver, but if you are in a crash—even
one that is not your fault—you and your passenger(s) can be
hurt. Being a good driver does not
protect you from things beyond your control, such as bad drivers. Most Toyota Sienna accidents occur within
25 miles (40 km) of home. And
the greatest number of serious injuries and deaths occur at
speeds of less than 40 mph (65 km/h).
Safety belts are for everyone.

OCCUPANT RESTRAINTS
Some of the most important safety features in your
Toyota Sienna are the restraint systems:
Three-point lap and shoulder belts for all seating positions
Pretensioning and load-limiting retractors for the front seat belts
Advanced multistage driver and new active-vent front passenger airbags
An energy-absorbing steering column and steering wheel
Knee Bolsters/Blockers for front seat occupants Front seat belt retractors incorporate pretensioners to
enhance occupant protection by managing occupant If you will a feature also can be used to
hold infant and child restraint systems.

In a collision, you and your passengers can suffer
much greater injuries if you are not properly buckled up. You can strike the interior of your Toyota Sienna or other
passengers, or you can be thrown out of the vehicle. Always be sure you and others in your Toyota Sienna are
buckled up properly.

Toyota Sienna Lap/Shoulder Belt Operating Instructions
1. Enter the vehicle and close the door. Sit back and adjust the seat.

2. The seat belt latch plate is near the seatback of the
front seats and next to your arm in the rear seats. Grasp
the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go
around your lap.

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”.

4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up
on the shoulder belt. To loosen the lap belt if it is too tight,
tilt the latch plate and pull on the lap belt.

A snug belt reduces the risk of sliding under the belt in a collision.

A belt that is buckled into the wrong buckle will
not protect you properly. The lap portion could ride too high on your body, possibly causing internal
injuries. Always buckle your belt into the buckle nearest you.
A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward,
increasing the possibility of injury. Wear your seat belt snugly.

It is extremely dangerous to ride in a Toyota Sienna cargo area, inside or outside
of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or
killed. Do not allow people to ride in any area of your vehicle that is
not equipped with seats and safety belts. Be sure everyone in
your vehicle is in a seat and using a safety belt properly.

I Keep Good Tires on my Toyota Sienna

2010-09-26T04:30:00.000-07:00

Toyota Sienna TIRE PRESSURES
Check the inflation pressure of each tire, including the spare tire, at least monthly and
inflate to the recommended pressure for your vehicle.
The tire pressures recommended for your vehicle are found on the “Tire and Loading
Information” label located on the driver’s side door opening.

WARNING!
Overloading of your Toyota Sienna tires is dangerous. Overloading can cause tire failure, affect
vehicle handling, and increase your stopping distance. Use tires of the recommended
load capacity for your vehicle. Never overload them.
WARNING!
Improperly inflated Toyota Sienna tires are dangerous and can cause accidents. Under-inflation is
the leading cause of tire failure and may result in severe cracking, component
separation, or “blow out”. Over-inflation reduces a tire’s ability to cushion shock.
Objects on the road and chuck holes can cause damage that results in tire failure.
Unequal tire pressures can cause steering problems. You could lose control of your
vehicle. Over-inflated or under-inflated tires can affect vehicle handling and can fail
suddenly, resulting in loss of vehicle control.

Toyota Sienna WHEEL AND WHEEL TRIM CARE
All Toyota Sienna wheels and wheel trim, especially aluminum and chrome plated wheels, should be
cleaned regularly with a mild soap and water to prevent corrosion.
To remove heavy soil and/or excessive brake dust, Toyota Sienna Wheel Cleaner or
equivalent or select a non-abrasive, non-acidic cleaner.
CAUTION!
Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use
oven cleaner. These products may damage the wheel's protective finish. Avoid
automatic car washes that use acidic solutions or harsh brushes that may damage the
wheel's protective finish. Only Toyota Sienna Wheel Cleaner or equivalent is recommended.

WARNING!
Raising the Toyota Sienna higher than necessary can make the vehicle less stable and cause
an accident. It could slip off the jack and hurt someone near it. Raise the Toyota Sienna only
enough to remove the tire.

At Least Once a Month check your Toyota Sienna's Tire Inflation
Inspect the vehicle’s tires and make sure they are inflated to the correct
pressures. Do not forget to check the spare tire, if the vehicle has one. If the vehicle has a spare tire, check to make sure it is stored
securely.

How to Check your Toyota Sienna's Tire Inflation
Use a good quality pocket-type gage to check tire pressure.
You can’t tell if your tires are properly inflated simply by
looking at them. Radial tires may look properly inflated even when they’re underinflated.
Check the tire’s inflation pressure when the tires are cold. Cold means your Toyota Sienna has been sitting for at least three
hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the
tire valve stem. Press the tire gage firmly onto the valve to get a pressure measurement.
If the cold tire inflation pressure matches the recommended pressure on the Toyota Sienna Tire and
Loading Information label, no further adjustment is necessary.
If the inflation pressure is low, add air until you reach the
recommended amount.If you overfill the tire, release air
by pushing on the metal stem in the center of the tire
valve. Recheck the tire pressure with the tire gage.
Be sure to put the valve caps back on the valve stems.
They help prevent leaks by keeping out dirt and moisture

Toyota Sienna Tire Wear Inspection
Tire rotation may be required for high mileage highway drivers prior to
the Engine Oil Life System service notification. Check the tires for
wear and, if necessary, rotate the tires

CAUTION
Driving your Toyota Sienna at high speeds, 100 mph
(160 km/h) or higher, puts an additional strain on tires. Sustained
high-speed driving causes excessive heat build up and can
cause sudden tire failure. You could have a crash and you or
others could be killed. Some high-speed rated tires require
inflation pressure adjustment for high speed operation. When speed
limits and road conditions are such that a vehicle can be driven at high
speeds, make sure the tires are rated for high speed operation, in excellent condition, and set to the
correct cold tire inflation pressure
for your Toyota Sienna's load.

Toyota Sienna Seat Belt Safety

2010-09-11T04:39:00.000-07:00

Toyota Sienna Features

The Toyota Sienna key can be used for the ignition and all locks.
Your Toyota Sienna has a Toyota Sienna theft-deterrent system. The
key has a transponder in the key head that is electronically coded to match a decoder in your Toyota Sienna that allows the key to start the Toyota Sienna . If a replacement key or any additional key is needed, you must
purchase it from your Toyota Sienna dealer/retailer.

Toyota Sienna Power Door Locks
You can use the Remote Keyless Entry (If your Toyota Sienna has one) transmitter to lock and unlock the doors from inside or outside the Toyota Sienna

Toyota Sienna Unlocked doors can be dangerous.
Passengers, especially children, can easily open the doors and fall out of a moving Toyota Sienna When a door is locked, the handle will not open it. You increase the chance of being thrown out of the Toyota Sienna in a crash if the doors are not locked. So, wear safety
belts properly and lock the doors whenever you drive.
Young children who get into unlocked Toyota Sienna may be unable to get out. A child can be
overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your Toyota Sienna whenever you leave it.
Outsiders can easily enter through an unlocked door when you slow down or stop your Toyota Sienna . Locking your doors can help prevent this from happening. To lock and unlock the Toyota Sienna manually: • From inside the Toyota Sienna , pull up or down on the manual door lock knob located on the windowsill.
From the outside the Toyota Sienna , turn the key toward the front or rear of the Toyota Sienna to unlock or lock
the door.

Toyota Sienna Exhaust gases may enter the Toyota Sienna if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.

If the Toyota Sienna must be driven with the liftgate, or trunk/hatch open:
Close all of the windows
Fully open the air outlets on or under the instrument panel
Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting.
If the Toyota Sienna is equipped with a power liftgate, disable the power liftgate function.

Toyota Sienna CAUTION:
Leaving children, helpless adults, or pets in a Toyota Sienna with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a Toyota Sienna , especially with the windows
closed in warm or hot weather.

Leaving children in a Toyota Sienna with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the Toyota Sienna move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a Toyota Sienna with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows.

Toyota Sienna WARNING!
For personal security and safety in the event of an accident, lock the Toyota Sienna doors as you drive as well as when you park and leave the Toyota Sienna .
When leaving the Toyota Sienna always remove the key and from the ignition lock, and lock your Toyota Sienna . Do not leave unattended children in the Toyota Sienna , or with access to an unlocked Toyota Sienna . Unsupervised
use of Toyota Sienna equipment may cause severe personal injuries and death.

Toyota Sienna Wind Buffeting
Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your Toyota Sienna may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to
minimize the buffeting.

Toyota Sienna Lap/Shoulder Belts
All seats in your Toyota Sienna are equipped with Lap/ Shoulder Belts. The belt webbing in the retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the Toyota Sienna or being thrown out.

Buckle up in your Toyota Sienna even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the insid of the Toyota Sienna . Everyone in a Toyota Sienna should be belted at all times.

Keep Driving your Toyota Sienna !

On the road in your Toyota Sienna

2010-09-04T02:09:00.000-07:00

Driving for Better Toyota Sienna Fuel Economy
Driving Your Toyota Sienna habits can affect fuel mileage. Here are some driving tips to get the best Toyota Sienna fuel economy possible.
Avoid fast starts and accelerate smoothly.
Brake gradually and avoid abrupt stops.
Avoid idling the engine for long periods of time.
When road and weather conditions are appropriate, use cruise control, if equipped.
Always follow posted speed limits or drive more slowly when conditions require.
Keep Toyota Sienna tires properly inflated.
Combine several trips into a single trip.
Replace the Toyota Sienna’s tires with the same TPC Spec number molded into the tire’s sidewall near the size.
Follow recommended scheduled maintenance.

Toyota Mini Van Defensive Driving
Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt
Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition:
Allow enough following distance between your Toyota Sienna and the driver in front of your Toyota Sienna.
Focus on the task of driving. Driver distraction can cause collisions resulting in injury or possible death.

Your Toyota Sienna Braking
Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception
time. Actually doing it is reaction time. Average reaction time is about three-fourths of a
second. But that is only an average. It might be less with one driver and as long as two or three seconds or
more with another. Age, physical condition, alertness, coordination, and eyesight all play a part. So do alcohol, drugs, and frustration. But even in three-fourths of a second, a Toyota Sienna moving at 60 mph (100 km/h) travels 66 feet (20 m). That could be a lot of distance in an emergency, so keeping enough space between the Toyota Sienna and others is important. And, of course, actual stopping distances vary greatly
with the surface of the road, whether it is pavement or gravel; the condition of the road, whether it is wet, dry, or icy; tire tread; the condition of the brakes; the weight of the Toyota Sienna; and the amount of brake force
applied. Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking. Keeping pace with the traffic and allowing realistic following distances eliminates a lot of unnecessary braking. That means
better braking and longer brake life. If the engine ever stops while the Toyota Sienna is being driven, brake normally but do not pump the Toyota Sienna brakes. If the brakes are pumped, the pedal could get harder to push down. If
the engine stops, there will still be some power brake assist but it will be used when the brake is applied. Once the power assist is used up, it can take longer to stop and the brake pedal will be harder to push. Adding non-dealer/non-retailer accessories can affect Toyota Sienna performance. Your Toyota Sienna Antilock Brake System (if your Toyota Sienna has it) This Toyota Sienna has Electronic Stability Control (if your Toyota Sienna has it) with the Antilock Brake System (if your Toyota Sienna has it), an advanced electronic braking system that will help prevent a braking skid. When the engine is started and the Toyota Sienna begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal. Let us say the road is wet and your Toyota Sienna are driving safely. Suddenly, an animal jumps out in front of your Toyota Sienna. your Toyota Sienna slam on the brakes and continue braking. Here is what happens with ABS: Your Toyota Sienna computer senses that the wheels are slowing down. If one of the wheels is about to stop rolling, the Toyota Sienna computer will separately work the brakes at each wheel. ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help the driver steer around the obstacle while braking hard. As the brakes are applied, the Your Toyota Sienna computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to geta foot up to the brake pedal or always decrease stopping distance. If your Toyota Sienna get too close to the Toyota Sienna in front of your Toyota Sienna, there will not be enough time to apply the brakes if that Toyota Sienna suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedaldown firmly and let antilock work. The antilock pump or motor operating might be heard and the brake pedal pulsating might be felt, but this is normal. Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This Toyota Sienna has a Brake Assist feature designed to
assist the driver in stopping or decreasing Toyota Sienna speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the Toyota Sienna. The Toyota Sienna stability system hydraulic brake control module increases brake pressure at each corner of the Toyota Sienna until the ABS activates. Minor brake pedal pulsations or pedal movement during this time is normal and the driver should continue to apply the brake pedal as the driving situation dictates
The Brake Assist feature will automatically disengage when the brake pedal is released or brake pedal pressure is quickly decreased.

Your Toyota Sienna Steering Tips
It is important to take curves at a reasonable speed. Traction in a curve depends on the condition of the tires and the road surface, the angle at which the curve is banked, and Toyota Sienna speed. While in a curve, speed is
the one factor that can be controlled. If there is a need to reduce speed, do it before entering the curve, while the front wheels are straight. Try to adjust the speed so your Toyota Sienna can drive through the
curve. Maintain a reasonable, steady speed. Wait to accelerate until out of the curve, and then accelerate gently into the straightaway. Steering in Emergencies There are times when steering can be more effective
than braking. For example, your Toyota Sienna come over a hill and find a truck stopped in your Toyota Siennar lane, or a car suddenly pulls
out from nowhere, or a child darts out from between parked cars and stops right in front of your Toyota Sienna. These problems can be avoided by braking — if your Toyota Sienna can stop in time. But sometimes your Toyota Sienna cannot stop in time
because there is no room. That is the time for evasive action — steering around the problem. The Toyota Sienna can perform very well in emergencies like these. First apply the brakes. It is better to remove as much speed as possible
from a collision. Then steer around the problem, to the left or right depending on the space available. An emergency like this requires close attention and a
quick decision. If holding the steering wheel at the recommended 9 and 3 o’clock positions, it can be turned
a full 180 degrees very quickly without removing either hand. But your Toyota Sienna have to act fast, steer quickly, and
just as quickly straighten the wheel once your Toyota Sienna have avoided the object. The fact that such emergency situations are always possible is a good reason to practice defensive driving
at all times and wear safety belts properly.

Your Toyota Sienna Off-Road Recovery
The Toyota Sienna’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the
pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the Toyota Sienna straddles the edge of the pavement. Turn the steering wheel 3 to 5 inches,
8 to 13 cm, (about one-eighth turn) until the right front tire contacts the pavement edge. Then turn the steering
wheel to go straight down the roadway.

Your Toyota Sienna Passing
Passing another Toyota Sienna on a two-lane road can be dangerous. To reduce the risk of danger while passing:
Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait.
Watch for traffic signs, pavement markings, and lines that could indicate a turn or an intersection. Never cross a solid or double-solid line on your Toyota Siennar side of the lane.
Do not get too close to the Toyota Sienna your Toyota Sienna want to pass. Doing so can reduce your Toyota Siennar visibility.
Wait your Toyota Siennar turn to pass a slow Toyota Sienna.
When your Toyota Sienna are being passed, ease to the right.

Your Toyota Sienna Loss of Control
Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction
where the tires meet the road to do what the driver has asked. In any emergency, do not give up. Keep trying to steer and constantly seek an escape route or area of less danger.

Your Toyota Sienna Drifting
In a skid, a driver can lose control of the Toyota Sienna. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible.
The three types of skids correspond to the Toyota Sienna’s three control systems. In the braking skid, the wheels are not rolling. In the steering or cornering skid, too much speed or steering in a curve causes tires to slip and lose
cornering force. And in the acceleration skid, too much throttle causes the driving wheels to spin. by easing your Toyota Siennar foot off the accelerator pedal. If the Toyota Sienna starts to slide, ease your Toyota Siennar foot off the
accelerator pedal and quickly steer the way your Toyota Sienna want the Toyota Sienna to go. If your Toyota Sienna start steering quickly enough,
the Toyota Sienna may straighten out. Always be ready for a second skid if it occurs.

Of course, Your Toyota Sienna traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, slow
down and adjust your Toyota Siennar driving to these conditions. It is important to slow down on slippery surfaces because
stopping distance will be longer and Toyota Sienna control more limited. While driving on a surface with reduced traction, try
your Toyota Siennar best to avoid sudden steering, acceleration, or braking, including reducing Toyota Sienna speed by shifting
to a lower gear. Any sudden changes could cause the tires to slide. your Toyota Sienna might not realize the surface is
slippery until the Toyota Sienna is skidding. Learn to recognize warning clues — such as enough water, ice, or
packed snow on the road to make a mirrored surface — and slow down when your Toyota Sienna have any doubt. Even though the Toyota Sienna has Electronic Stability Control (if your Toyota Sienna has it) with Antilock Brake System (if your Toyota Sienna has it), remember:
ABS helps avoid only the braking skid. If the ABS is ever disabled, in a braking skid, where the Toyota Siennas wheels are no longer rolling, release enough pressure
on the brakes to get the wheels rolling again. This restores steering control. Push the brake pedal down steadily when your Toyota Sienna have to stop suddenly. As long as the
wheels are rolling, your Toyota Sienna will have steering control.

How I keep Up My Toyota Sienna's Appearance

2010-08-25T12:48:00.000-07:00

My Toyota Sienna Appearance Care

Toyota Sienna Interior Cleaning
my Toyota Sienna’s interior will continue to look its best if it is cleaned often.
Although not always visible, dust and dirt can accumulate on my Toyota Sienna upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from the Toyota Sienna upholstery. It is important to keep my upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. my Toyota Sienna’s interior may experience extremes of heat that could cause stains to set rapidly. Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to my home furnishings may also transfer color to my Toyota Sienna’s interior.

When cleaning my Toyota Sienna’sinterior,
only use cleaners specifically designed for the surfaces being cleaned. Permanent
damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth.

Notice: If you use abrasive cleaners when cleaning glass surfaces on my Toyota Sienna,you could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on my Toyota Sienna, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in my Toyota Sienna’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning my Toyota Sienna’s interior, maintain adequate ventilation by opening my Toyota Sienna’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles. my dealer/retailer has a product for cleaning my Toyota Sienna’s glass. You can also obtain a product from my dealer/retailer to remove odors from my Toyota Sienna’s upholstery.

I Do not clean my Toyota Sienna using the following cleaners or techniques:
• Never use a knife or any other sharp object to remove a soil from any interior surface.
• Never use a stiff brush. It can cause damage to my Toyota Sienna’s interior surfaces.
• Never apply heavy pressure or rub aggressively with a cleaning cloth. Use of heavy pressure can damage the interior and does not improve the effectiveness of soil removal.
• Use only mild, neutral-pH soaps. Avoid laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.
• Do not heavily saturate the upholstery while cleaning.
• Damage to my Toyota Sienna’s interior may result from the use of many organic solvents such as naptha, alcohol, etc.

My Toyota Sienna's Fabric/Carpet
I Use a vacuum cleaner with a soft brush attachment frequently to
remove dust and loose dirt. A canister vacuum with a beater bar in
the nozzle may only be used on floor carpet and carpeted floor mats. For
soils, always try to remove them first with plain water or club soda. Before
cleaning, gently remove as much of the soil as possible using one of the
following techniques:
• For liquids: gently blot the remaining soil with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed.
• For solid dry soils: remove as much as possible and then vacuum.
To clean, use the following instructions:
1. Saturate a lint-free, clean white cloth with water or club soda.
2. Wring the cloth to remove excess moisture.
3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
4. Continue to gently rub the soiled area until the cleaning cloth remains clean.
5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process that was used with plain water. If any of the soil remains, a
commercial fabric cleaner or spot lifter may be necessary. When acommercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first.
If the locally cleaned area gives any impression that a ring formation may
result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet.

Toyota Sienna Leather seats
A soft cloth dampened with water can be used to remove dust. If a
more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the Toyota Sienna's leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve
and protect leather may permanently change the appearance and
feel of my leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean my Toyota Sienna’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on leather.

Toyota Sienna Instrument Panel, Vinyl, and Other Plastic Surfaces
A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of my interior and are not recommended. Do not use silicone or wax-based products, or those containing
organic solvents to clean my Toyota Sienna’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner.

Some commercial products may increase gloss on my instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make
it difficult to see through the windshield under certain conditions.

Cleaning Exterior Toyota Sienna's Lamps/Lenses
Use only lukewarm or cold water, a soft cloth and a car washing soap to
clean exterior lamps and lenses. Follow instructions under “Washing
my Toyota Sienna” later in this blog.

Toyota Sienna Finish Care
Occasional waxing or mild polishing of the Toyota Sienna by hand may be
necessary to remove residue from the paint finish. You can get approved cleaning products from my Toyota Sienna's dealer/retailer. If the Toyota Sienna has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a
basecoat/clearcoat paint finish.
Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish
may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/
clearcoat paint finish on my Toyota Sienna.

Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can
damage the Toyota Sienna’s finish if they remain on painted surfaces. Wash the Toyota Sienna as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping the Toyota Sienna garaged or covered whenever possible.

Protecting Toyota Sienna Exterior Bright Metal Parts
Toyota Sienna's Bright metal parts should be cleaned regularly to keep their
luster. Wash with water or use chrome polish on chrome or stainless steel trim, if necessary. Use special care with Toyota Sienna's aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean
aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.

Washing my Toyota Sienna
The best way to preserve the Toyota Sienna’s finish is to keep it clean by washing it often. Do not wash the Toyota Sienna in direct sunlight. Use a car washing soap.

Toyota Sienna Notice: Certain cleaners contain chemicals that can damage
the emblems or nameplates on my Toyota Sienna. Check the cleaning
product label. If it states that it should not be used on plastic
parts, do not use it on my Toyota Sienna or damage may occur and
it would not be covered by the warranty. Do not use cleaning agents that are
petroleum based or that contain acid or abrasives, as they can damage
the paint, metal or plastic on the Toyota Sienna. Approved cleaning products
can be obtained from my dealer/ retailer. Follow all manufacturers’
directions regarding correct product usage, necessary safety precautions
and appropriate disposal of any Toyota Sienna care product.

Rinse the Toyota Sienna well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain.
Dry the finish with a soft, clean chamois or an all-cotton towel to
avoid surface scratches and water spotting. High pressure car washes may
cause water to enter the Toyota Sienna. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the Toyota Sienna. Use of power washers exceeding 1,200 psi (8 274) can result in damage or removal of paint and decals.

Notice: Conveyor systems on some automatic car washes could damage the Toyota Sienna. There may not be enough clearance for the undercarriage. Check with the car wash manager before using the automatic car wash.

Toyota Sienna Weatherstrips
Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required.

Toyota Sienna's Wheels and Trim — Aluminum or Chrome
The Toyota Sienna may have either aluminum or chrome-plated wheels.
Keep the wheels clean using a soft clean cloth with mild soap and water.
Rinse with clean water. After rinsing thoroughly, dry with a soft clean
towel. A wax may then be applied.

Notice: Toyota Sienna Chrome wheels and other chrome trim may be damaged if you do not wash my Toyota Sienna after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash my Toyota Sienna’s chrome with soap and water after exposure. Notice: If you use strong soaps,chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by my warranty. Use only approved cleaners on aluminum or chrome-plated wheels. The surface of these wheels is similar to the painted surface of the Toyota Sienna. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Notice: Using chrome polish on aluminum wheels could damage
the wheels. The repairs would not be covered by my warranty. Use chrome polish on chrome wheels only. se chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application.

Notice: If you drive my Toyota Sienna through an automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by my Toyota Sienna's warranty. Never drive aToyota Sienna equipped with aluminum or chrome-plated wheels through an automatic car wash
that uses silicone carbide tire cleaning brushes. Windshield and Wiper Blades
Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of Toyota Sienna wash/wax treatments may cause wiper streaking. Replace thewiper blades if they are worn or damaged.

Your Toyota Sienna's Wipers can be damaged by:
• Extreme dusty conditions
• Sand and salt
• Heat and sun
• Snow and ice, without proper removal

Your Toyota Sienna's Tires
To clean the tires, use a stiff brush with tire cleaner.

Notice: Using petroleum-based tire dressing products on my Toyota Sienna may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on my Toyota Sienna.

Chemical Paint Spotting
Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the Toyota Sienna. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, we will repair, at no charge to the owner, the surfaces of new Toyota Siennas damaged by this fallout condition within 12 months or12,000 miles (20 000 km) of purchase, whichever occurs first.

My Toyota Sienna's Underbody Maintenance
Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. my dealer/retailer or an underbody car washing system can do this for you.
Sheet Metal Damage
If the Toyota Sienna is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the Toyota Sienna warranty.
Finish Damage
Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from my Toyota Sienna's dealer/retailer. Larger areas of finish damage can be corrected in my Toyota Sienna's body and paint shop.

Toyota Sienna

My Toyota Sienna Dashboard layout

2010-08-15T12:14:00.000-07:00

Toyota Sienna Dashboard Instrument Panel, Warning Lights

Toyota Sienna DashBoard overview

1.} Toyota Sienna Side defroster outlets
2.} Toyota Sienna Side vents
3.} Toyota Sienna Instrument cluster
4.} Toyota Sienna Automatic transmission selector lever
5.} Toyota Sienna Center vents
6.} Toyota Sienna Garage door r opener box or auxiliary box
7.} Toyota Sienna Electric c moon roof switch or personal light switch
8.} Toyota Sienna Front personal llights or front interior light
9.} Toyota Sienna Power door lock switches
10.} Toyota Sienna Power window switches
11.} Toyota Sienna Glove box
12.} Toyota Sienna Auxiliary boxes
13.} Toyota Sienna Tilt steering lock release lever
14.} Toyota Sienna Hood lock release lever
15.} Toyota Sienna Parking brake pedal
16.} Toyota Sienna Window lock switch

Toyota Sienna Cockpit overview

1.} Toyota Sienna Headlight and turn signal switch
2.} Toyota Sienna Wiper and washer switches
3.} Toyota Sienna Clock

4.} Toyota Sienna Air conditioning controls
5.} Toyota Sienna Emergency flasher switch
6.} Toyota Sienna Rear r window and outside rear view wmirror defoggers switch
7.} Toyota Sienna Power rear quarter window switch
8.} Toyota Sienna Rear fan speed selector
9.} Toyota Sienna Car audio
10.} Toyota Sienna Ashtray
11.} Toyota Sienna Cigarette lighter
12.} Toyota Sienna Power outlet
13.} Toyota Sienna Power sliding door switch
14.} Toyota Sienna Ignition switch
15.} Toyota Sienna Cruise control switch
16.} Toyota Sienna Audio remote control buttons
17.} Toyota Sienna Power sliding door off switch
18.} Toyota Sienna Theft tdeterrent system/Engine immobiliser system indicator light
19.} Toyota Sienna Tire pressure warning system reset switch
20.} Toyota Sienna Power rear view mirror control switch
21.} Toyota Sienna Instrument panel light control dial

Toyota Sienna Warning Indicator symbols on the Dashboard

Toyota Sienna Warnings

2010-08-07T04:45:00.000-07:00

Toyota Sienna Service reminder indicators and warning buzzers
(a) Toyota Sienna Brake System Warning Light' This light has the following functions:
Parking brake reminder If this light is on, make sure the parking
brake is fully released. The light should go off. Toyota Sienna Low brake fluid level warning If this light comes on and stays on while you are driving, slow down and pull off the road. Then stop the my Toyota Sienna carefully. Remember that stopping distance and pedal effort may be increased. There maybe a problem somewhere in the Toyota Sienna brake system. Check the fluid level of the seethrough reservoir. To make sure the Toyota Siennas parking brake has not
caused the warning light to come on, check to see that the parking brake is fully released. If the brake fluid level is low... At a safe place, test your Toyota Sienna brakes by starting and stopping. If you judge that the brakes still work adequately, drive cautiously to your nearest dealer or shop for repairs. If the brakes are not working, have the my Toyota Sienna towed in for repairs. If the brake fluid level is correct... Have the warning system checked by yourToyota Sienna dealer.

(b) Toyota Sienna Driver’s Seat Belt Reminder Light and Buzzer
This light and buzzer remind you to buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and
buzzer sounds if the driver’s seat belt is not pulled out. Unless the driver starts to pull the shoulder belt out of the retractor, the Toyota Sienna light keeps flashing and the buzzer stops after about 4 to 8 seconds.

(c) Toyota Sienna Front Passenger’s Seat Belt Reminder
Light This light reminds you to buckle up the front passenger’s seat belt.
Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a
passenger sits in the front passenger seat and does not pull out the seat belt. Unless the front passenger starts to pull the Toyota Sienna shoulder belt out of the retractor, the light stays flashing. If luggage load is placed on the front passenger seat, depending on its weight and how it is placed on the seat, built- in sensors in the seat cushion may detect the pressure, causing the reminder light to come on.

(d) Toyota Sienna Discharge Warning Light This light warns that the Toyota Sienna battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to operate, however, until the battery is discharged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota Sienna dealer or repair shop.

(e) Toyota Sienna Malfunction Indicator Lamp
This lamp comes on in the following cases.
a. The Toyota Sienna fuel tank is completely empty.
b. The Toyota Sienna fuel tank cap is not tightened securely.
c. There is a problem somewhere in your
Toyota Sienna engine or Toyota Sienna automatic transmission electrical system. If it comes on while you are driving in case c, have your my Toyota Sienna checked/repaired by your Toyota Sienna dealer as soon as possible.

(f) Toyota Sienna Low Fuel Level Warning Light
This light comes on when the Toyota Sienna fuel level in the tank becomes nearly empty. Fill up
the tank as soon as possible. On inclines or curves, due to the movement of fuel in the tank, the low fuel level warning light may come on earlier than usual.

(g) Toyota Sienna Low Oil Pressure Warning Light
This light warns that the Toyota Sienna engine oil pressure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota Sienna dealer or qualified repair shop for assistance.
The light may occasionally flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when
the engine is accelerated slightly. The light may come on when the Toyota Sienna oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.

(h) Toyota Sienna “ABS” Warning Light

This light warns that there is a problem somewhere in your anti- lock brake system. If the light comes on while you are driving, have your my Toyota Sienna checked by your Toyota Sienna dealer as soon as possible. The light will come on when the ignition key is turned to the “ON” position. After a few seconds, the light will go off. When the Toyota Sienna ABS warning light is on (and the brake system warning light is off), the brake system operates conventionally but anti- lock brake system is not assisting

brake performance so that the Toyota Sienna wheels can lock- up during sudden braking or braking
on slippery road surfaces.

(i) Toyota Sienna Open Door Warning Light
This light remains on until all the doors and back door are completely closed.
When the Toyota Sienna ignition switch is “OFF” and this light stays lighting on, the light will turn off automatically after 30 minutes with the light flashing five times. See “Personal lights” and “Interior light” for details in Sanouther post.

(j) Toyota Sienna Open Power Sliding Door Warning Light and Buzzer
This light comes on if the power sliding door is not completely closed with the
ignition key in the “ON” position. If you forcibly close the power sliding door
by hand when the ignition key is in the “ON” position, the open power sliding door
warning light may stay on. In this case, try opening and closing the Toyota Sienna power sliding
door again by hand slowly, or use one of the “PWR DOOR” switches or wireless
remote control transmitter. If you shift out of “P” when the power
sliding door is opened or in the process of closing with the power sliding door system on, a buzzer will sound and the open Toyota Sienna power sliding door warning light will flash. This is a warning that the sliding door is not completely closed.

(k) Toyota Sienna SRS Warning Light
This light will come on when the ignition key is turned to the “ACC” or
“ON” position. After about 6 seconds, the light will go off. This means the
system of the airbag and front seat belt pretensioners are operating properly.
The Toyota Sienna warning light system monitors the airbag sensor assembly, front airbag sensors,
seat belt pretensioner assemblies, inflators, warning light, interconnecting wiring
and power sources. If either of the following conditions occurs,
this indicates a malfunction somewhere in the parts monitored by the warning light
system. Contact your Toyota Sienna dealer as soon as possible to service the my Toyota Sienna. The light does not come on when the ignition key is turned to the “ACC” or “ON” position or remains on. The light comes on or flashes while driving.

(l) Toyota Sienna Low Windshield Washer Fluid Level Toyota Sienna Warning Light
The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity.

(m) Toyota Sienna Low Tire Pressure Warning Light
This light warns that the Toyota Sienna tire pressure of any one of the tires is critically reduced. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the low Toyota Sienna tire pressure warning system is functioning properly. If the light comes on while driving, adjust
tire pressure to the specified level. After the tire pressure is adjusted, the light should go off after driving at about more than 30 km/h (19 mph) for some time. If the light still remains, have the low tire pressure warning system checked at your Toyota Sienna dealer.

(n) Key Reminder Buzzer
This buzzer reminds you to remove the key when you open the driver’s door with
the ignition key in the “ACC” or “LOCK” position.
Toyota Sienna CHECKING SERVICE REMINDER INDICATORS (except the low fuel level warning
light and low windshield washer fluid level warning light)
1. Apply the Toyota Sienna parking brake.
2. Open one of the Toyota Sienna doors. The openToyota Sienna door warning light should come on.
3. Close the door. The open door warning light should go off.
4. Turn the ignition key to “ACC”. The Toyota Sienna SRS warning light should come on. It goes off after about 6 seconds.
5. Turn the Toyota Sienna ignition key to “ON”, but do not start the Toyota Sienna engine. All the service reminder indicators except the open door warning light, open power sliding door warning light and SRS warning light should come on. The “ABS” warning light and low tire pressure warning light go off after a few seconds.
6.Toyota Siennas with a power sliding door:
Open the Toyota Sienna right side sliding door. The open power sliding door warning light should come on. Close the Toyota Sienna right side sliding door. The open power sliding door warning
light should go off. If any service reminder indicator or warning buzzer does not function as described above, either the bulb is burned out or the circuit is in need of repair. Have it checked by your Toyota Sienna dealer as soon as possible.
Toyota Sienna

My New Toyota Sienna, Fuel

2010-08-03T13:58:00.000-07:00

My Toyota Sienna Break-in period Drive gently and avoid high speeds.

My Toyota Sienna does not need an elaborate break-in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of my vehicle:
Do not drive over 88 km/h (55 mph). Run the engine at moderate speed between 2000 and 4000 rpm. Avoid full-throttle starts. Try to avoid hard stops during the first 300 km (200 miles). Do not drive for a long time at any single speed, either fast or slow. Do not tow a trailer during the first 800 km (500 miles).

My Toyota Sienna Fuel FUEL TYPE

my new Toyota Sienna must use only unleaded gasoline.

To help prevent gas station mix-ups, my Toyota Sienna has a new smaller fuel tank opening. The special nozzle on pumps with unleaded fuel will fit it, but the larger standard nozzle on pumps with leaded gas will not.

At a minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB 3.5-M93 in Canada.

NOTICE
Do not use leaded gasoline. Use of leaded gasoline will cause the Toyota Sienna three-way catalytic converter to lose its effectiveness and the emission control system to function improperly. Also, this can increase maintenance costs.

Toyota Sienna OCTANE RATING
Select Octane Rating 87 (Research Octane Number 91) or higher. For improved vehicle performance, the use of premium unleaded gasoline with an Octane Rating of 91 (Research Octane Number 96) or higher is recommended.

Use of unleaded gasoline with an octane rating or research octane number lower than stated above will cause persistent heavy knocking. If it is severe, this will lead to engine damage.

If My Toyota Sienna engine knocks...

If I detect heavy knocking even when using the recommended fuel, or if I hear steady knocking Toyota Sienna Toyota dealer.

However, now and then, you may notice light knocking for a short time while accelerating or driving up hills. This is no need of concern.

GASOLINES CONTAINING DETERGENT ADDITIVES
recommend use of gasolines that contain detergent additives to avoid build-up of engine deposits.

For further details, ask your Toyota dealer or a local gasoline retailer.

IMPROVED GASOLINES
The American Automobile Manufacturers Association (AAMA) has developed a specification of improved gasolines. The AAMA specification offers optimal fuel information for better vehicle performance and better protection of your engine.
recommend the use of gasolines that meet the AAMA specification, if available, for improved driveability and emission control system.

GASOLINES CONTAINING MTBE
Gasolines that contain MTBE (Methyl Tertiary-Butyl Ether) are available in the market. If you use a gasoline mixed with MTBE, make certain that it does not contain more than 15% of MTBE.

GASOLINES CONTAINING MMT
Some gasolines contain an octane-en-hancing additive called MMT (methylcyclopentadienyl manganese tricarbonyl).

do not recommend the use of gasolines that contain MMT. If fuels containing MMT are used, your emission control system may be adversely affected. The Malfunction Indicator Lamp on the instrument cluster may come on. If this happens, contact your Toyota Sienna dealer for service.

GASOLINES CONTAINING ALCOHOL
If you use gasohol in your Toyota Sienna, be sure that it is unleaded, has an octane rating no lower than 87 and does not contain more than 10% ethanol.

Gasohol is a mixture of gasoline and ethanol.
doe not recommend the use of gasolines containing methanol. If you use gasoline containing methanol, use only gasoline meeting the requirements above and also containing less than 5% methanol with cosolvents and corrosion inhibitors for methanol.

Toyota Sienna GASOLINES QUALITY
In a very few cases, you may experience driveability problems caused by the particular gasoline that you are using. If you continue to have unacceptable driveability, try changing gasoline brands. If that does not rectify your problem, then consult your Toyota dealer.

NOTICE
Do not use gasohol other than stated above. It will cause Toyota Sienna fuel system damage or Toyota Sienna performance problems.

If driveability problems occur (poor hot starting, vaporizing, engine knock, etc.), discontinue the use.

Take care not to spill gasohol during refueling. Gasohol may cause paint damage.

My Toyota Sienna FUEL TANK CAPACITY

79 L (21 gal., 17.5 lmp. gal.)

Operation in foreign countries Three-way catalytic converter
If you plan to drive your Toyota in

another country... First, comply with the vehicle registration laws.

Second, confirm the availability of the correct fuel (unleaded and minimum octane number).

The three-way catalytic converter is an emission control device installed in the exhaust system.

The purpose is to reduce pollutants in the exhaust gas.

A large amount of unburned gases flowing into the three-way catalytic converter may cause it to overheat and create a fire hazard. To prevent this and other damage, observe the following precautions: Use only unleaded gasoline.

Type B
Toyota Sienna Engine exhaust cautions
Do not drive with an extremely low fuel level; running out of fuel could cause the engine to misfire, creating an excessive load on the three-way catalytic converter.
Do not allow the Toyota Sienna engine to run at idle speed for more than 20 minutes.
Avoid racing the Toyota Sienna engine.
Do not push-start or pull-start your Toyota Sienna.
Do not turn off the ignition while the vehicle is moving.
Keep your engine in good running order. Malfunctions in the engine electrical system, electronic ignition system/distributor ignition system or fuel system could cause an extremely high three-way catalytic converter temperature.
If the engine becomes difficult to start or stalls frequently, take your vehicle in for a check-up as soon as possible. Remember, my Toyota dealer knows your Toyota Sienna and its three-way catalytic converter system best.

Toyota Sienna Trailer Towing

2010-04-24T09:21:00.000-07:00

TRAILER TOWING TIPS

When towing a trailer, your Toyota Sienna will handle differently than when not towing. The three main causes of vehicle trailer accidents are driver error, excessive speed and improper trailer loading. Do not just hook up a Trailer and Haul Ass down the road. Towing is not a joke and should be taken seriously! So Keep these in mind when towing:
- Before starting out, check operation of the lights and all Toyota Sienna - trailer connections. After driving a short distance, stop and recheck the lights and connections. Before actually towing a trailer, practice turning, stopping and backing with a trailer in an area away from traffic until you learn the feel.
- Backing with a trailer is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This procedure is generally opposite to that when backing without a trailer). Also, just turn the steering wheel a little at a time, avoiding sharp or prolonged turning. Have someone guide you when backing to reduce the risk of an accident.
- Because stopping distance may be increased, vehicle- to- vehicle distance should be increased when towing a trailer. For each 16 km/h (10 mph) of speed, allow at least one vehicle and trailer length between you and the vehicle ahead. Avoid sudden braking as you may skid, resulting in jackknifing and loss of control. This is especially true on wet or slippery surfaces.
- Avoid jerky starts or sudden acceleration.
- Avoid jerky steering and sharp turns. The trailer could hit your Toyota Sienna in a tight turn. Slow down before making a turn to avoid the necessity of sudden braking.
- Remember that when making a turn, the trailer wheels will be closer than the Toyota Sienna's wheels to the inside of the turn. Therefore, compensate for this by making a larger than normal turning radius with your Toyota Sienna.
- Crosswinds and rough roads will adversely affect handling of your Toyota Sienna and trailer, causing sway.
Pay attention to the rear from time to time to prepare yourself for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying happens, firmly grip the steering wheel and reduce speed immediately but gradually. Never increase speed. Steer straight ahead. If you make no extreme correction with the steering or brakes, the Toyota Sienna and trailer will stabilize. Be careful when passing other vehicles. Passing requires considerable distance. After passing a vehicle, do not forget the length of your trailer and be sure you have plenty of room before changing lanes.
- In order to maintain engine braking efficiency,do not use overdrive.
- Because of the added load of the trailer, your Toyota Sienna’s engine may overheat on hot days (at temperatures over 30 C [85 F]) when going up a long or steep grade with a trailer. If the engine coolant temperature gauge indicates overheating, immediately turn off the air conditioning (if in use), pull off the road and stop in a safe spot.
- Always place wheel blocks under both the Toyota Sienna and trailer wheels when parking. Apply the parking brake firmly. Put the transmission in “P”. Avoid parking on a slope with a trailer, but if it cannot be avoided, do so only after performing the following:
1. Apply the brakes and hold.
2. Have someone place wheel blocks under both the Toyota Sienna and trailer wheels.
3. When the wheel blocks are in place, release your brakes slowly until the blocks absorb the load.
4. Apply the parking brake firmly.
5. Shift into “P” and turn off the engine.

When restarting out after parking on a slope:
1. With the transmission in “P” position, start the engine. Be sure to keep the brake pedal depressed.
2. Shift into gear.
3. Release the parking brake and brake pedal and slowly pull or back away from the wheel blocks. Stop and apply your brakes.
4. Have someone retrieve the blocks.
CAUTION
- Do not exceed 72 km/h (45 mph) or the posted towing speed limit, whichever is lower. Because instability (swaying) of a towing vehicletrailer combination usually increases as the speed increases, exceeding 72 km/h (45 mph) may cause loss of control.
- Slow down and downshift before descending steep or long downhill
grades. Do not make sudden downshifts. Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

Do not use your parking brake when there is a possibility it could freeze. When parking, put the transmission into “P” and block the rear wheels. Do not use the parking brake, or snow or water accumulated in and around the parking brake mechanism may freeze, making it hard to release. Keep ice and snow from accumulating under the fenders. Ice and snow built up under your fenders can make steering difficult. During bad winter driving, stop and check under the fenders occasionally.
Carry some emergency equipment.
Some of the things you might put in the Toyota Sienna are tire chains, window scraper, bag of sand or salt, flares, small shovel, jumper cables, socket set, safety glasses, water, etc.

Your Sienna is designed primarily as apassenger- and- load- carrying vehicle. Towing a trailer will have an adverse effect on handling, performance, braking, durability and driving economy (fuel consumption, etc.). Your safety and satisfaction depend on the proper use of correct equipment and cautious driving habits. For your safety and the safety of others, you must not overload your vehicle or trailer. Ask your local Toyota dealer for further details before towing with your Toyota Sienna.

WEIGHT LIMITS
Before towing, make sure the total trailer weight, gross combination weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits. The total trailer weight and tongue load can be measured with platform scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

The maximum gross trailer weight (trailer weight plus cargo weight)must never exceed the following: Toyota Sienna Without towing package 907 kg (2000 lb.), Toyota Sienna With towing package 1587 kg (3500 lb.) If towing a trailer and cargo weighing over 907 kg (2000 lb.), it is necessary to use a sway control device with sufficient capacity. The combination of the gross trailer weight added to the total weight of the vehicle, occupants and vehicle cargo must never exceed a total of the following. Toyota Sienna Without towing package 3129kg (6900 lb.), Toyota Sienna With towing package 3537 kg (7800 lb.) Exceeding the maximum weight of the trailer, the Toyota Sienna, or the Toyota Sienna and trailer combination, can cause an accident resulting in serious personal injuries.

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capable of towing a higher weight, the operator must determine the maximum weight rating of the particular hitch assembly and never exceed the maximum weight rating specified for the trailer- hitch. Exceeding the maximum weight rating set by the trailer hitch manufacturer can cause an accident resulting in serious personal injuries

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum of weights of the unloaded vehicle, driver, passengers, luggage, hitch and trailer tongue load. It also includes the weight of any special equipment installed on your Toyota Sienna.

The load on either the front or rear axle resulting from distribution of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

The trailer cargo load should bedistributed so that the tongue load is 9 to 11% for weight carrying hitch (*1) or 15% for weight distributing hitch (*2) of the total trailer weight, not exceeding the maximum load of the following.

Weight carrying hitch Without towing package 90 kg (200 lb.) With towing package 158 kg (350 lb.) Weight distributing hitch With towing package 238 kg (525 lb.) Never load the trailer with more weight in the back than in the front. About 60% of the trailer load should be in the front half of the trailer and the remaining 40% in the rear.

HITCHES
If you wish to install a trailer hitch on your Toyota Sienna, you should consult with your Toyota dealer. Use only a hitch recommended by the hitch manufacturer and the one which conforms to the total trailer weight requirement. The hitch must be bolted securely to the vehicle frame and installed according to the hitch anufacturer’s instructions. The hitch ball and king pin should have a light coat of grease.

Remove the trailer hitch whenever you are not towing a trailer to reduce the possibility of additional damage caused by the hitch if your vehicle is struck from behind. After removing the hitch, seal any mounting holes in the vehicle body to prevent entry of pollutants such as exhaust fumes, dirt, water, etc.
Do not use axle- mounted hitches as they can cause damage to the axle housing, wheel bearings, wheels or tires. Also, never install a hitch which may interfere with the normal function of an Energy Absorbing Bumper, if so equipped.

BRAKES AND SAFETY CHAINS
Use trailers with brakes that conform to any applicable federal and state/provincial regulations. A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in case it becomes damaged or separated. For correct safety chain procedures, follow the hitch or trailer manufacturer’s recommendations.
CAUTION
If the total trailer weight exceeds 453 kg (1000 lb.), trailer brakes are required.
Never tap into your vehicle’s hydraulic system as it would lower its braking effectiveness. Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering over into another lane.

TIRES
Ensure that your Toyota Sienna’s tires are properly inflated. The trailer tires should be inflated to the pressure recommended by the trailermanufacturer in respect to the total trailer weight.
TRAILER LIGHTS
Trailer lights must comply with federal, state/provincial and local regulations.
See your local recreational vehicle dealer or rental agency for the correct type of wiring and relays for your trailer. Check for correct operation of the turn signals and stop lights each time you hitch up. Direct splicing may damage your vehicle’s electrical system and cause a malfunction of your lights.
BREAK- IN SCHEDULE
Do not tow a trailer with a new Toyota Sienna or a Toyota with any new power train component (engine, transmission, differential, wheel bearing, etc.) for the first 800 km (500 miles) of driving.
MAINTENANCE
If you tow a trailer, your Toyota Sienna will require more frequent maintenance due to the additional load. Retighten all fixing bolts of the towing ball and bracket after approximately 1000 km (600 miles) of trailer driving.
PRE- TOWING SAFETY CHECK
Check that your Toyota Sienna remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle has an abnormal nose- up or nose- down condition, and check for improper tongue load, overload, worn suspension or other possible causes. Make sure the trailer cargo is securely loaded so that it cannot shift. Check that your rear view mirrors conform to any applicable federal, state/ provincial or local regulation. If not, install the rear view mirrors required for towing purpose.

Starting and Driving my Toyota Sienna

2010-03-19T02:57:00.000-07:00

Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle,seat cushion angle, head restraint height and steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.

How to start the engine—
(a) Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in “P”. If you need to restart the engine while the vehicle is moving, put the selector lever in “N”. A starter safety device will prevent the starter from operating if the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until driving off.
(b) Starting the engine
Before starting the engine, be sure to follow the instructions in “(a) Before cranking”.
Normal starting procedure
The multiport fuel injection system/sequential multiport fuel injection system in your engine automatically controls the proper air- fuel mixture for starting. You can start a cold or hot engine as follows:
1. With your foot off the accelerator pedal, crank the engine by turning the key to “START”. Release it when the engine starts.
2. After the engine runs for about 10 seconds, you are ready to drive.
If the weather is below freezing, let the engine warm up for a few minutes before driving. If the engine stalls... Simply restart it, using the correct procedure given in normal starting.

Tips for driving in various conditions
Always slow down in gusty crosswinds. This will allow you much better control. Drive slowly onto curbs and, if possible, at a right angle. Avoid driving onto high, sharp- edged objects and other road hazards. Failure to do so can lead to severe tire damage resulting in tire bursts.
When parking on a hill, turn the front wheels until they touch the curb so that the vehicle will not roll. Apply the parking brake, and place the transmission in “P”. If necessary, block the wheels. Washing your vehicle or driving through deep water may get the brakes wet. To
see whether they are wet, check that there is no traffic near you, and then
press the pedal lightly. If you do not feel a normal braking force, the brakes
are probably wet. To dry them, drive the vehicle cautiously while lightly
pressing the brake pedal with the parking brake applied. If they still do not
work safely, pull to the side of the road and call a Toyota dealer for assistance.

Winter driving tips
Make sure you have a proper freeze protection of engine coolant.
Your coolant must contain ethylene- glycol type coolant for a proper corrosion
protection of aluminum components. Use “TOYOTA Long Life Coolant” or equivalent.
Do not use alcohol type antifreeze or plain water alone.

When it is extremely cold, we recommend to use 60% solution for your Toyota, to
provide protection down to about -50°C (- 58°F). Do not use more than 70% solution
for better coolant performance. Check the condition of the battery and cables. Cold temperatures reduce the capacity of any battery, so it must be in top shape to provide enough power for winter starting. inspect the battery. Your Toyota dealer and most service stations will be pleased to check the level of charge.

Make sure the engine oil viscosity is suitable for the cold weather.
Leaving a heavy summer oil in your vehicle during winter months may cause harder starting. If you are not sure about which oil to use, call your Toyota dealer— they will be pleased to help. Keep the door locks from freezing. Squirt lock de- icer or glycerine into the locks to keep them from freezing. Use a washer fluid containing an antifreeze solution. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

Toyota Sienna Unfortunate Situations

2009-11-17T16:56:00.000-08:00

If your Toyota Sienna will not start—
(a) Simple checks
Before making these checks, make sure you have followed the correct starting procedure and that you have sufficient fuel. If your Toyota Sienna is equipped with the engine immobiliser system, also check whether the other keys will start the engine. If they work, your key may be broken. Have the key checked at your Toyota dealer. If none of your keys work, the system is possibly broken. Call your Toyota Sienna dealer.
If the Toyota Sienna engine is not turning over or is turning over too slowly
Check that the Toyota Sienna battery terminals are tight and clean.

If the battery terminals are O.K., switch on the interior light.
If the Toyota Sienna light is out, dim or goes out when the Toyota Sienna starter is cranked, the battery is discharged. You may try jump starting. See “(c) Jump starting” for further instructions.

If the light is O.K., but the engine still will not start, it needs adjustment or repair. Call a Toyota Sienna dealer or qualified Toyota Sienna repair shop.
Do not pull-or push-start the Toyota Sienna. It may damage the vehicle or cause a collision when the engine starts. Also the three-way catalytic converter may overheat and become a fire hazard.
If the Toyota Sienna engine turns over at its normal speed but will not start— Check that all the push-on connectors are tight. (For example, connectors at the Toyota Sienna spark plugs, ignition coil and/or distributor)

If the connectors are O.K., the Toyota Sienna engine may be flooded because of repeated cranking. See “(b) Starting a flooded engine” for further instructions.
(b) Starting a flooded Toyota Sienna engine
If the engine will not start, your engine may be flooded because of repeated cranking.
If this happens, turn the Toyota Sienna key to “START” with the accelerator pedal held down. Keep the key and accelerator pedal so for 15 seconds and release them. Then try starting the engine with your foot off the accelerator pedal.
If the Toyota Sienna engine does not start after 15 seconds of cranking, release the key, wait a few minutes and try again.
If the engine still will not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop for assistance.
Do not crank for more than 30 seconds at a time. This may overheat the Toyota Sienna starter and Toyota Sienna wiring systems.
(c) Toyota Sienna Jump starting
To avoid serious personal injury and damage to your Toyota Sienna which might result from battery explosion, acid burns, electrical burns, or damaged electronic components, these instructions must be followed precisely.

If you are unsure about how to follow this procedure, it is strongly recommend that you seek the help of a competent mechanic or towing service.

The battery used for boosting must be 12 V. Do not jump start unless you are sure that the booster battery is correct.

Toyota Sienna JUMP STARTING PROCEDURE

If the booster battery is installed in another Toyota Sienna , make sure the vehicles are not touching. Turn off all unnecessary lights and accessories.

If required, remove all the vent plugs from the booster and discharged batteries. Lay a cloth over the open vents on the batteries. (This helps reduce the explosion hazard, personal injuries and burns.)

If the engine in the vehicle with the booster battery is not running, start it and let it run for a few minutes. During jump starting, run the Toyota Sienna engine at about 2000 rpm with the accelerator pedal lightly depressed.

4. Make the cable connections in the order a, b, c, d.

.

.

a. Connect the clamp of the positive (red) jumper cable to the positive ( ) terminal on the discharged Toyota Sienna battery.

b. Connect the clamp at the other end of the positive (red) Toyota Sienna jumper cable to the positive ( ) terminal on the booster battery.

..
.
.
.
c. Connect the clamp of the negative (black) Toyota Sienna jumper cable to the negative (-) terminal on the booster battery.

d. Connect the clamp at the other end of the negative (black) jumper cable to a solid, stationary, unpainted, metallic point of the Toyota Sienna with the discharged battery.

The recommended connecting point is shown in the following illustration:

.

.

Toyota Sienna Connecting point
Do not connect the cable to or near any part that moves when the Toyota Sienna engine is cranked.

.
.
.
.
.
If you have a flat tire in your Toyota Sienna

Reduce your Toyota Sienna speed gradually, keeping a straight line. Move cautiously off the road to a safe place well away from the traffic. Avoid stopping on the center divider of a highway. Park on a level spot with firm ground.

Stop the Toyota Sienna engine and turn on your Toyota Sienna emergency flashers.
Firmly set the Toyota Sienna parking brake and put the transmission in “P”.

Have everyone get out of the Toyota Sienna on the side away from traffic. And get far away from the roadway.

Read the following instructions thoroughly.
Do not continue driving with a deflated tire. Driving even a short distance can damage a Toyota Sienna tire beyond repair.

Compact spare tire

The compact spare tire is designed for temporary emergency use only.

The compact spare tire is identified by the distinctive wheel design and color and special wording “TEMPORARY USE ONLY” molded into the side wall of the tire.

The standard tire should be repaired and replaced as soon as possible.

To keep the compact Toyota Sienna spare tire noticeable, do not hide the wheel by a wheel cover or such.
The Toyota Sienna compact spare tire saves space in your luggage compartment, and its lighter weight helps to improve fuel economy and permits easier installation in case of a flat tire.

The compact spare tire can be used many times, if necessary. It has tread life of up to 4800 km (3000 miles) depending on road conditions and your driving habits. When tread wear indicators appear on the tire, replace the tire.

Your ground clearance is reduced when the compact Toyota Sienna spare tire is installed so avoid driving over obstacles and drive slowly on rough, unpaved roads and speed bumps. Also, do not attempt to go through an automatic car wash as the Toyota Sienna may get caught, resulting in damage.

1. Get the required tools and spare tire from your Toyota Sienna.

Toyota Sienna Jack
Jack handle
Wheel nut wrench
Toyota Sienna Spare tire

To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations.

Turn the jack joint by hand.

To remove: Turn the joint in direction 1 until the jack is free. To store: Turn the joint in direction 2 until the jack is firmly secured to prevent it flying forward during a collision or sudden braking.

To remove the spare tire;Open the back door and you will find the spare tire clamp bolt near the back door latch. Loosen the spare tire clamp bolt by turning it counterclockwise with the wheel nut wrench. After the tire is lowered completely to the ground, remove the holding bracket.

Compact spare tire— When storing the spare tire, put it in place with the inner side of the wheel facing up.
Except compact spare tire— When storing the spare tire, put it in place with the outer side of the wheel facing up.
Then secure the Toyota Sienna tire by repeating the above removal steps in reverse order to prevent it from flying forward during a collision or sudden braking.

Make sure to pull the tire straight up without catching on any other part.

Do not overtighten the bolt. Stop turning it when you begin to feel resistance on your hand.

After storing the Toyota Sienna tire, make sure it is securely locked by pushing it forward and rearward.
—Blocking the wheel —Removing wheel ornament

2. Block the wheel diagonally opposite the flat tire to keep the vehicle from rolling when it is jacked up.

When blocking the wheel, place a wheel block from the front for the front wheels or from the rear for the rear wheels.
3. Remove the Toyota Siennas wheel ornament.

Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.
Steel wheels

Toyota Sienna Aluminium wheels
—Loosening wheel nuts —Positioning the jack —Raising your vehicle

4. Loosen all the wheel nuts.

Always loosen the Toyota Sienna wheel nuts before raising the vehicle.

The nuts turn counterclockwise to loosen. To get maximum leverage, fit the wrench to the nut so that the handle is on the right side, as shown above. Grab the wrench near the end of the handle and pull up on the handle. Be careful that the wrench does not slip off the nut.

Do not remove the nuts yet—just unscrew them about one-half turn.

5. Position the Toyota Sienna jack at the correct jack point as shown.

Make sure the Toyota Sienna jack is positioned on a level and solid place.

6. After making sure that no one is in the Toyota Sienna, raise it high enough so that the spare tire can be installed.
Remember you will need more ground clearance when putting on the Toyota Sienna spare tire than when removing the flat tire.

To raise the vehicle, insert the jack handle into the jack (it is a loose fit) and turn it clockwise. As the jack touches the vehicle and begins to lift, double-check that it is properly positioned.

—Changing Toyota Sienna wheels

7. Remove Toyota Siennas tires.

Roll the spare wheel into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.

Before putting on wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal-to-metal contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving. Therefore after the first 1600 km (1000 miles), check to see that the wheel nuts are tight.

—Reinstalling Toyota Sienna wheel nuts —Lowering your Toyota Sienna

8. Reinstall all the Toyota Sienna wheel nuts finger tight.

Reinstall the wheel nuts (tapered end inward) and tighten them as much as you can by hand. Press back on the tire and see if you can tighten them more.

9. Lower the Toyota Sienna completely and tighten the wheel nuts.

Turn the jack handle counterclockwise to lower the vehicle.

Use only the wheel nut wrench to tighten the nuts. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the wrench is securely engaged over the nut.

Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight.

—Reinstalling Toyota Sienna wheel ornament —After changing Toyota Sienna wheels

Steel wheels

Toyota Sienna Aluminum wheels

10. Reinstall the Toyota Sienna wheel ornament.

1. Put the wheel ornament into position.

Steel wheel models, align the cutout of the wheel ornament with the valve stem as shown.

2. Then tap it firmly with the side or heel of your hand to snap it into place.

11. Check the Toyota Sienna air pressure of the replaced tire.

Do not forget to reinstall the tire inflation valve cap as dirt and moisture could get into the valve core and possibly cause air leakage. If the cap is missing, have a new one put on as soon as possible.

12. Restow all the tools, Toyota Sienna jack and flat tire securely.
As soon after changing wheels as possible, tighten the wheel nuts

Toyota Siennas with a spare tire of the same size as the installed tires—

13. Push the Toyota Sienna tire pressure warning system reset switch.

Toyota Sienna

Toyota Sienna Appearance And Care

2009-11-01T17:19:00.000-08:00

Toyoata Sienna CORROSION PREVENTION AND APPEARANCE CARE
Toyota, through its diligent research, design and use of the most advanced
technology available, has done its part to help prevent corrosion and has provided
you with the finest quality vehicle construction. Now, it is up to you. Proper care of your Toyota Sienna can help ensure longterm corrosion prevention. The most common causes of corrosion to your Toyota Sienna are:
The accumulation of road salt, dirt and moisture in hard- to- reach areas under
the vehicle. Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.Care is especially important if you live in particular areas or operate your Toyota Sienna under certain environmental conditions: Road salt or dust control chemicals will accelerate corrosion, as will the presence of salt in the air near the seacoast or in areas of industrial pollution. High humidity accelerates corrosion especially when temperatures range just above the freezing point. Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry. High temperatures will cause corrosion to those components of the vehicle which are prevented from quick- drying due to lack of proper ventilation. The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any damage to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your Toyota Sienna frequently. It is, of course, necessary to keep your Toyota Sienna clean by regular washing, but to prevent corrosion, the following points should be observed: If you drive on salted roads in the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize corrosion. High pressure water or steam is effective for cleaning the vehicle’s undersideand wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing them. The lower edge of Toyota Sienna doors, Toyota Sienna rocker panels and Toyota Sienna frame members have drain holes
which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion. Wash the underside of the Toyota Sienna thoroughly when winter is over. Check the condition of your Toyota Sienna’s paint and trim. If you find any chips or scratches in the Toyota Sienna paint, touch them up immediately to prevent corrosion from starting.
If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.
Protecting your Toyota Sienna from corrosion
Check the interior of your Toyota Sienna . Water and dirt can accumulate under the
Toyota Sienna floor mats and could cause corrosion. Occasionally check under the mats to make
sure the area is dry. Be particularly careful when transporting chemicals, cleansers,
fertilizers, salt, e tc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use Toyota Sienna mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your Toyota Sienna . Full- size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your Toyota Sienna in a damp, poorly ventilated garage. If you wash your vehicle in the garage, or if you drive it in covered with water or snow, your garage may be so damp it will cause corrosion. Even if your garage is heated, a wet Toyota Sienna can corrode if the ventilation is poor.
Washing your Toyota Sienna
Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as Possible. When driving in a coastal area When driving on a road sprinkled with antifreeze When having stuck of coal tar, tree sap, bird droppings and carcass of an insect When driving in the areas where there is a lot of smoke, soot, dust, iron dust
and chemical substance When the vehicle becomes remarkably dirty with dust and mud
Hand- washing your Toyota Work in the shade and wait until the Toyota Sienna body is not hot to the touch. When cleaning under floor or chassis, be careful not to injure your hands. 1. Rinse off loose dirt with a hose. Remove any mud or road salt from the underside of the vehicle or in the wheel wells. 2. Wash with a mild car- wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt. Toyota Sienna Aluminum wheels: Use only a mild soap or neutral detergent. Toyota Sienna Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft. Road tar: Remove with turpentine or cleaners that are marked safe for painted surfaces. Do not use gasoline or strong solvents, which may be toxic or cause damage. 3. Rinse thoroughly—dried soap can cause streaking. In hot weather you may need to rinse each section right after you wash it.
Washing and waxing your Toyota Sienna
4. To prevent water spots, dry the Toyota Sienna using a clean soft cotton towel. Do not
rub or press hard—you might scratch the Toyota Sienna paint. Automatic car wash Your vehicle may be washed in an automatic car wash, but remember that the Toyota Sienna paint can be scratched by some type of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you whether
the process is safe for the paint on your Toyota Sienna . NOTICE With mast type Toyota Sienna antenna: To prevent damage to the antenna, make sure it is removed before driving your Toyota through an automatic car wash. When your Toyota Sienna goes through an automatic car wash, make sure the power sliding door system is off. Waxing yourToyota Sienna Polishing and waxing is recommended to maintain the original beauty of your Toyota Sienna’s finish.
Once a month or if the vehicle does not repel water well, apply wax. 1. Always wash and dry the vehicle before you begin waxing, even if you are using a combined cleaner and wax. 2. Use a good quality polish and wax. If the finish has become extremely weathered, use a car- cleaning polish, followed by a separate wax. Carefully follow the Toyota Sienna manufacturer’s instructions and precautions. Be sure to polish and wax the Toyota Sienna chrome trim as well as the paint. 3. Wax the vehicle again when water
does not bead but remains on the surface in large patches. NOTICE Always remove the plastic bumpers if your Toyota Sienna is re- painted and placed in a high heat paint waxing booth. High temperatures could damage the bumpers. Cleaning the interior
CAUTION Do not wash the Toyota Sienna floor with water, or allow water to get onto the
floor when cleaning theToyota Sienna interior or exterior. Water may get into audio components or other electrical components above or under the Toyota Sienna floor carpet (or mat) and cause a malfunction; and it may cause body corrosion. Vinyl interior The Toyota Sienna vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First acuum over the upholstery to remove loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the Toyota Sienna vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, repeat the procedure. Commercial foamingtype vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.
Do not use solvent, thinner, gasoline or window cleaner on the interior. Toyota Sienna Carpets
Use a good foam- type shampoo to clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol can sand others are powders or liquids which you mix with water to produce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the Toyota Sienna carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with l ukewarm water. Use a cloth or sponge. As you are cleaning, check the belts for excessive wear, fraying, or cuts. Do not use dye or bleach on the belts—it may weaken them. Do not use the belts until they become dry. Windows The Toyota Sienna windows may be cleaned with any household window cleaner. When cleaning the inside of the windows, be careful not to scratch or damage the heater wires on the rear window. Air conditioning Toyota Sienna control panel, car audio, instrument panel, c onsole panel, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or lukewarm water then lightly wipe off dirt. Do not use organic substances (solvents, kerosene, alcohol, gasoline, etc.) or lkaline or acidic solutions. These chemicals can cause discoloring, staining or peeling of the surface. If you use cleaners or polishing agents, make sure their ingredients do not include the substances mentioned above. If you use a liquid car freshener, do not spill the liquid onto the vehicle’s interior surfaces. It may contain the ingredients mentioned above. Immediately clean any spill using the method mentioned above. Leather Interior The leather upholstery may be cleaned with neutral detergent for wool. Remove dirt using a soft cloth dampened with 5% solution of neutral detergent for wool. Then thoroughly wipe off all traces of detergent with a clean damp cloth. After cleaning or whenever any part of the Toyota Sienna leather gets wet, dry with a soft clean cloth. Allow the Toyota Sienna leather to dry in a ventilated shaded area. If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent. Never use organic substances such as benzine, alcohol or gasoline, or alkaline or acid solutions for cleaning the leather as these could c ause discoloring. Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather. Mildew may develop on soiled leather upholstery. Be especially careful to avoid oil spots. Try to keep your Toyota Sienna upholstery always clean. Long exposure to direct sunlight may cause the leather surface to harden and shrink. Keep your Toyota Sienna in a shaded area, especially in the summer. The interior of your Toyota Sienna is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm. Improper cleaning of the Toyota Sienna leather upholstery could result in discoloration or staining.