Mobile Phone Code secret

Nokia (Plus) Secret Codes (Complete)

2010-12-19T20:31:00.000-08:00

Posted: 2006-11-18 03:15

.:: NOKIA ::.Universal Codes
Code Description :
These Nokia codes will work on most Nokia Mobile Phones
(1) *3370# Activate Enhanced Full Rate Codec (EFR) - Your phone uses the best sound quality but talk time is reduced by approx. 5%
(2) #3370# Deactivate Enhanced Full Rate Codec (EFR) OR *3370# ( Favourite )
(3) *#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time.
(4) *#4720# Deactivate Half Rate Codec.
5) *#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type. ( Favourite )
(6) *#9999# Phones software version if *#0000# does not work.
(7) *#06# For checking the International Mobile Equipment Identity (IMEI Number). ( Favourite )
(8) #pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).
(9) #pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).
(10) #pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).
(11) #pw+1234567890+4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).
(12) *#147# (vodafone) this lets you know who called you last.
(13) *#1471# Last call (Only vodofone).
(14) *#21# Allows you to check the number that "All Calls" are diverted to
(15) *#2640# Displays security code in use.
(16) *#30# Lets you see the private number.
(17) *#43# Allows you to check the "Call Waiting" status of your phone.
(18) *#61# Allows you to check the number that "On No Reply" calls are diverted to.
(19) *#62# Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to.
(20) *#67# Allows you to check the number that "On Busy Calls" are diverted to.
(21) *#67705646# Removes operator logo on 3310 & 3330.
(22) *#73# Reset phone timers and game scores.
(23) *#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible.
24) *#7760# Manufactures code.
(25) *#7780# Restore factory settings.
26) *#8110# Software version for the nokia 8110.
(27) *#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair
(0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again. (Favourite )
(28) *#94870345123456789# Deactivate the PWM-Mem.
(29) **21*number# Turn on "All Calls" diverting to the phone number entered.
(30) **61*number# Turn on "No Reply" diverting to the phone number entered.
(31) **67*number# Turn on "On Busy" diverting to the phone number entered.
(32) 12345 This is the default security code.

press and hold # Lets you switch between lines

IMEI number: * # 0 6 #
Software version: * # 0 0 0 0 #
Simlock info: * # 9 2 7 0 2 6 8 9 #
Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off]
Half Rate: * 4 7 2 0 #
Provider lock status: #pw+1234567890+1
Network lock status #pw+1234567890+2
Provider lock status: #pw+1234567890+3
SimCard lock status: #pw+1234567890+4

NOKIA 6110/6120/6130/6150/6190
IMEI number: * # 0 6 #
Software version: * # 0 0 0 0 #
Simlock info: * # 9 2 7 0 2 6 8 9 #
Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off]
Half Rate: * 4 7 2 0 #

NOKIA 3110
IMEI number: * # 0 6 #
Software version: * # 0 0 0 0 # or * # 9 9 9 9 # or * # 3 1 1 0 #
Simlock info: * # 9 2 7 0 2 6 8 9 #

NOKIA 3330

*#06# This will show your warranty details *#92702689#
*3370# Basically increases the quality of calling sound, but decreases battery length.
#3370# Deactivates the above
*#0000# Shows your software version
*#746025625#This shows if your phone will allow sim clock stoppage
*4370# Half Rate Codec activation. It will automatically restart
#4370# Half Rate Codec deactivation. It will automatically restart
Restore Factory Settings To do this simply use this code

*#7780# Manufacturer Info Date of Manufacturing *#3283#
*3001#12345# (TDMA phones only) This will put your phone into programming mode, and you'll be
presented with the programming menu.

2) Select "NAM1"
3) Select "PSID/RSID"
4) Select "P/RSID 1"
Note: Any of the P/RSIDs will work
5) Select "System Type" and set it to Private
6) Select "PSID/RSID" and set it to 1
7) Select "Connected System ID"
Note: Enter your System ID for Cantel, which is 16401 or 16423. If you don't know yours, ask your local dealer for it.
Select "Alpha Tag"
9) Enter a new tag, then press OK
10) Select "Operator Code (SOC)" and set it to 2050
11) Select "Country Code" and set it to 302 for Canada, and 310 for the US.
12) Power down the phone and power it back on again ISDN Code To check the ISDN number on your Nokia use this code *#92772689#.::

Ericsson

Ericson T65

*#05# Fake Insert puk screen Press no to exit

Ericsson T20
MENU tecnichal Info
[type] >*<<*<*
Displays :

1] Info service
1] Info SW
2] Info hardware
3] SIMlock
4]setup

2] Service setup
1] Contrast

3]Service Test
1] Display
2]Leds
3]Keyboard

4] ringer

5] Vibration

6]Headset

7] Microphone

8]Clock

4] Names List
MENU info
[Type] >*<<**<
Network and Subnetwork : NCK and NSCK

EricssonT28

>*<<*<* menu Tecnichal info SW vers. and name list >*<<**< menu Personal Info Network and Subnetwork : NCK and NSCK < and > are the right and left menu's keysEricsson T18s/T10/A1018s
>*<<*<* software CXC125065 Internal product code PRG 970715 1515 Software version and SW rev.<* CLR <><**>*<<*<*> Displays texts and messages in the phone It will be displayed " TEXT " then push YES < and > are the right and left menu's keys !!!><** Control /Enable SIM Lock!!!
Ericsson R310 Technical Info : >*<<*<*Options :

1) service Info info Software Simlock Configuration

2) Service Test Display Led/Illumination Keyboard ringer Vibration Headset Microphone Clock

3)Text's name List Info personal : >*<<**< SIM Locking ( 8 digits' code ) ( it could harm your phone )

1) Network

2) Subnetwork

3) SP

4) Corporate

.:: Siemens ::.

Siemens C25
IMEI number: * # 0 6 #
Software version: put off sim card and enter: : * # 0 6 # and press LONG KEY Bonus screen: in phone booke: + 1 2 0 2 2 2 4 3 1 2 1

.:: Bosch ::.

IMEI Number: * # 0 6 #
Dafault Language: * # 0 0 0 0 #
Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 #

.::Alcatel::.

IMEI number: * # 0 6 #Software version: * # 0 6 #
Net Monitor: 0 0 0 0 0 0 *

.:: Samsung ::.

Samsung SGH600/2100DB IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 # albo * # 0 8 3 7 #
Net Monitor: * # 0 3 2 4 #
Chaning LCD contrast: * # 0 5 2 3 #
Memory info: * # 0 3 7 7 # albo * # 0 2 4 6 #
Reset pamieci (SIMLOCK`a removing!!!): *2767*3855#
Reset pamieci CUSTOM: *2767*2878#
Battery state: * # 9 9 9 8 * 2 2 8 #
Alarm beeper: *#9998*289#
Vibra test: *#9998*842#::.
IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 #

.:: Philips ::.
*#3333*# Displays the blocking list.
*#7489*# Displays the security code.
*#06# Displays the IMEI number.
*#8377*# Displays the SW info.

.:: Panasonic ::.
Panasonic gd90 gd93
*#9999# SW - Type the code on switch on , during network seek-Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with "tone menu "

Panasonic gd70
*#9999# SW - Type the code on switch on , during network seek-Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with "tone menu "

.:: Acer ::.
Acer V 750
*#400# Display Adc/ Set Cal-Value -
*#402# Set LCD Contrast
*#403# Display Errors Info
*#300# Display Info Hw & Sw
*#301# Menu Test
*#302# Menu Acoustics
*#303# (Settings saved) Set English language?
*#307# Menu Engineering
*#311# Reset Phone Code - [ Also reset Security Codes ! ]
*#330# (Execute not success) [ unknown ]
*#331# (Service deactivated) [ unknown ]
*#332# (Service unavailable)[ unknown ]
*#333# (Execute not success)[ unknown ]
*#351# (Service unavailable) [ unknown ]
*#360# (Invalid input)[ unknown ]
*#361# (Invalid input) [ unknown ]
*#362# (Invalid input) [ unknown ]
#363# (Invalid input) [ unknown ]

.:: Genie ::.
Genie DB *#06# IMEI.
*#2254*# Near Cell Mode.For every received BTS will be displayed :
Current channel and 2 channel levels
*#06# IMEI
*#2558# time of network connection ( D/H/M )
*#2562# Fores reconnection to network
!!!*#7489# Dispalys and modify phones' security code!!!
!!!*#3377# SIM lock information !!!
*#7378# SIM card Informations : supported phase name and tipe
*#7693# Enable/disable "Sleep Mode"
*#8463# State of "Sleep Mode"
*#2255# Debug Call Mode enable/disable
*#3333*# Displays the blocking list.
*#7489*# Displays the security code
*#06# Displays the IMEI number
*#8377*# Displays the SW info.

.:: NEC ::.
NEC db2000 *#2820# software vers.
IMEI *#06#
Reset *73738# (send?)
SP Lock info:
* # 3210 # (send?)
Network barring info : *#8140# (send?)
( it could harm your phone )
SIM lock it could harm your phone )
*#4960 # (send?) -Inquiry * 4960 * password * password # (send?) lock
#4960* password # (send?) unlock
[password] [8 digits]
Net Lock
*#7320# (send?) -Inquiry * 7320 * password * password # (send?) lock
#7320* password # (send?) unlock
[password] [ 8 digits]
Net Lock 2:
*#2220# (invio) - Inquiry * 2220 * password * password # (send?) lock
#2220* password # (invio?)unlock
[password] [8 digits]
Unlock subnetwork
*#1110# (send?) - inquiry * 1110 * password * password # (send?) lock
#1110* password # (send?) unlock
[password] [nï¿½ 8 cifre]
( it could harm your phone )

.:: Trium ::.

Trium Geo/Geo @ - Astral - Cosmo -AriaEnter the menu and type *
A new menu will be displayed :
Application : SW version and battery's voltage
Trium Galaxy
Push * and type 5806: Production date and SW version

.:: Telit ::.

Telit GM 810 MONITOR - technical menu - : type ++++ and push OK.
Adiacent cells list : # and *
Now if you push OK the phone displays battery ' s voltage and temperature

.:: Sagem ::.
Sagem MC959/940
Select commands' menu and push *
Displays a new menu' :
Appli : software vers. and battery's voltage
Eprom
Sim Lock
Test LCD: display test , green/red and vibration

Sagem MC920
Select commands' menu and push *
Displays 5 new menus :
1 APPLI
VERSION ( SW)
BATTERY (voltage )
2 PROM (IMEI)
3!!! SIM LOCK (10 digits code requested ) !!!
4- NETWORK (returns : OPTION NOT AVAILABLE)
5- TEST LCD
SYMBOL 1 (LCD)
SYMBOL 2 (test2 LCD)
BLACK (all icons and carachters displayed )
FOR PHOTO (welcome message and time )
VIBRATOR (vibration test )

.:: Sony ::.
Sony CMD Z5/J5
Vers. SW :
Without SIM , switch on phone and type l *#7353273#

.:: Eprom ::.
!!! Sim Lock [10 digits code ] ( it could harm your phone )
NETWORK : OPTION NOT AVAILABLE
Test LCD: display test of the green/red leds and vibration
Push * and type 4329 :enables/disables network monitor 1 (the same of MT35)
Push * and type 621342 :enables/disables network monitor 2
Push * and type 5807 : Serial Number Software Vers.
Push * and type 936505: IMEI -- Software Vers.
TPush * and type 547 : Test serial Data Cable DISPLAYS :"Testmode"
Push * and type 362628: ISMI BLOCK (UNKNOWN)
Push * and type 476989: NS BLOCK (UNKNOWN)
Push * and type 482896:CP BLOCK (UNKNOWN)
Push * and type 787090: ? BLOCK (UNKNOWN)
Push * and type 787292 : block current network
!!! Push * and type 967678: SP LOCK!!!
Push * and type 850696:Warm Start ( ENABLE/DISABLE)
Push * and type 3926 : Swicth off phone
Push * and type 5806: Production date and SW version

.:: Motorola ::.
Motorola V3688

IMEI *#06#
Enhanced Full Rate Codec EFR
Enable EFR : [][][] 119 [] 1 [] OK.
disable EFR : [][][] 119 [] 0 [] OK

.:: Tips and Tricks ::.
Send an E-mail from your GSM
From your telephone you can send an email to whichever E-mail customer of the Internet network.The e-mail will be sent to the maximum of within an hour from the reception.The sended message will contain in luminosity the telephone number of the sender. In order for sending e-mail, send an SMS with this syntax (always separated by spaces):EMA name@domain text-of-your-email Example: in order to send an email to john@doe.com, do the following: EMA john@doe.com text-of-your-email if your phone cant print @ replace it with a ! EMA johon!doe.com text-of-your-email And then send this message to the folloving number: +39 338 8641732

Free SMS Center numbers
From your telephone you can send SMS messages of 160 char. max. to another GSM phoneYour message will be sent through an SMS Center (usually the one that gave your provider) You pay a little fee depending of your provider, BUT YOU WILL HAVE TO PAY something In order for sending SMS without paying anything, you got to change your SMS Center number with these one +491722270300 or +358405202999 or 352021100003

Codes (that they dont tell you in the manual)
To check the IMEI (International Mobile Equipment Identity) type: *#06# Information you get from the IMEI:
XXXXXX XX XXXXXX X TAC FAC SNR SP TAC = Type Approval Code (first 2 digits = country code).
FAC = Final Assembly Code (For Nokia phones FAC=10). SNR = Serial Number. SP = Spare (always SP=0).To check the phone's software (firmware revision information) type: *#0000# ( or for some phones outher then Nokia 61XX you can try *#model nummber# ex. for 8110 *#8110#) Information you can get from the phone's software version: V 3.14 28-11-97 NSE-3 1st line: Software version. 2nd line: The date of the software release.3nd line: Phone type, .Some versions and dates:V 3.14 28/11/97 V4.33 11/03/98 V 4.73 22/04/98 V 5.24 14/9/98

Pin-Out Diagram for the 6110

1 - VIN CHARGER INPUT VOLTAGE 8.4V 0.8A
2 - CHRG CTRL CHARGER CONTROL PWM 32Khz
3 - XMIC MIC INPUT 60mV - 1V
4 - SGND SIGNAL GROUND
5 - XEAR EAR OUTPUT 80mV - 1V
6 - MBUS 9600 B/S
7 - FBUS_RX 9.6 - 230.4 KB/S
8 - FBUS_TX 9.6 - 230.4 KB/S
9 - L_GND CHARGER / LOGIC GND

Revealing Headphone and Car-Kit Menus
Think about this: If you do these tricks the new menus can not be erased after the procedure. But it's not dangerous or harmful for your phone To enable the headset-function, you have to short-circuit the "3" and "4". After a short time there is "Headset" on the display Now, menu 3-6 is now enabled! To enable the carkit-function you have to short-circuit the "4" and "5". After a short time, "Car" is shown on the display and the menu 3-7 is enabled!!

This Trick is for you how want to hear more then your supposed to!

If you short-circuit the left and the right contact with the middle contact ("3", "6" and "9") the Nokia Software hangs! The profile "Headset" will be activated. Before you do this, just active the "auto call receive" function in the headphone profile and set the ringing volume to "mute" Now you can use your phone for checking out what people are talking about in a room. Place the phone somewhere stratidic and call your phone! The phone receives the call without ringing and you can listen to what people are talking about! .....gr8...

Serial numbers on your 6110
For more info type: *#92702689#
The first screen gives you the serial and IMEI number.
Then there is the Date of Manufacture: ex. Made 1297
Then there is the Purchasing Date: ex. Purchasing Date 0298
Then there is the last Repair Date: ex. Repaired: 0000
Note: you must turn off the phone to exit after this test, because of the last function, "transfer user data" which Doesn't work as "standard"....You can use this mode only to transfer all Calender, Profile and Callers Group Information to another phone (eg. if you are replacing phone or configuring phones for use within your company or when a particular phone doesn't works correctly )

Activating and deactivating EFR and HFR, on your 6110

*3370# to activate Enhanced Full Rate - Makes calls sound better, but decreases the battery life by about 5%.#3370# to deactivate Enhanced Full Rate
*4720# to activate Half Rate Mode - Drops call quality, but increases battery life by about 30%.
#4720# to deactivate Half Rate Mode

Motorola Secret Codes(Complete)-002

2010-12-19T20:29:00.001-08:00

[MOTOROLA]

--------------------------------------------------------------------------------

Motorola 7760, 7860, 2260, 8160, etc Nam Programming:

Nam Set: Fcn,0000000000000, Rcl

Nam Set: 74663#, Fcn, Fcn

Test Mode: Fcn, 00**83786633, Sto

Motorola v60c, v120c etc Nam Programming:

Nam Set: 74663#, Menu, Menu, Spc

Nam Set: Menu, 073887, * (type quickly)

Test Mode: Menu, 073887*, Spc

Debug Mode: ##33284

Force the phone into DIGITAL ONLY mode:

1) ##33284 (Debug)

2) RIGHT Softkey (Next) Twice

3) Down arrow 10 times to "PrefMod"

4) RIGHT Softkey (Change) until you see "DigOnly"

5) LEFT softkey (Exit)

6) MENU then LEFT Softkey return to idle screen

7) ##33284 (The last 4 will not display if you have done it correctly)

Motorola t182, c210, etc Nam Programming:

Nam Set: ##1111 end

Nam Set: ##298645665 end

Short Nam: ##073887 sto

Motorola v710, v730, v740, ms150, etc Nam Programming:

Nam Set: 8378*# + press 3 times NATE (spc - 071082)

Test Mode: Menu, 073887*, Spc

Service Menu: #758353266#646#

Motorola StarTac 2004 Nam Programming:

Nam Set: 5759789*#, rec key (3)times (spc - 915037)

Motorola ms200, ms230, etc Nam Programming:

Nam Set: 5759789*# (spc - 915037)

Motorola v6060 Nam Programming:

Nam Set:147*369#456*0#

MOTOROLA TEST MODE:

v60, c120, c331, etc:

1) Turn on the phone. Press MENU 0 7 3 8 8 7 *

2) The phone will require you to "Enter a Security Code", press 000000, OK

3) Scroll down to "Test mode" choose SELECT. Scroll down to "Enable"

choose SELECT. Your phone is now in test mode.

4) Signal strength is the 3_rd number down on the left hand side of the screen.

5) To toggle between regular mode and test mode: Press MODE then

quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.

6) To turn off the test mode the phone must be in regular mode, then follow

the above sequence and scroll down to where it says "DISABLE" instead of

"ENABLE" and choose select.

Motorola Bible - bible.txt

Motorola Secret Codes(Display Problem)

2010-12-19T20:28:00.001-08:00

W220 Display problem

Thanx code works 1000000000000%

motorola w220
display problem
*#**367628#+send key master reset

*#**778337#+send key E2p reset
----------------------------------------------------------------

Motorola Secret Codes(Complete)

2010-12-19T20:27:00.001-08:00

look here if you need any code

Service codes Motorola CDMA: w150, w150i, w170, w170c, w200, w210, w355:

Set English language:
1. Menu
2. Down 7 times, Right soft button
3. Down 3 times, Right soft button
4. Down 1 times, Right soft button
5. Down 4 times, Right soft button
6. select language now

Service codes Samsung:
E900 software version: *#5002*8376263#
E900 full reset: *2767*3855#
Service codes Spice:
S404 enable COM port: *#42253646633# -> Device -> Set UART -> PS -> UART1/115200
S410 engineer mode: *#3646633#
S900 software version: *#8375#
S900 serial no: *#33778#
Service codes Philips:
S200 enable COM port: *#3338913# -> Device -> Set UART -> PS -> UART1/115200
Service codes "Chinese" models:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
Service codes BenQ:
software version: *#300#
test mode: *#302*20040615#
Service codes Pantech:
software version: *01763*79837#
service menu: *01763*476#
reset defaults (phone/user code reset to default): *01763*737381#
Service codes VK-Mobile 3xx, 5xx:
software version: *#79#
software version: *#837#
service menu: *#85*364# (hold #)
Service codes VK200, VK2000, VK2010, VK2020, VK4000:
software version: *#79#
service menu: *#9998*8336# (hold #)
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
Service codes LG:
software version: 2945#*#
KG300 NVRAM format: 2945#*# -> menu 15
Service codes Sony-Ericsson:
J100 software version: #82#
Service codes Fly:
M100 software version: ####0000#
2040(i) reset defaults: *#987*99# Send
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Konka:
C926 software version: *320# Send
C926 set default language: *#0000# Send
C926 set English language: *#0044# Send
Service codes GStar:
GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Motofone-F3:
Motofone F3 software version: **9999* Send
***300* Set SIM Pin
***310* / ***311* SIM Pin ON | OFF
***000* Reset Factory settings
***644* Set Voicemail number
***260* / ***261* Auto keypad lock ON | OFF
***510* / ***511* Voice Prompts ON | OFF
***160* / ***161* Restricted Calling (Phonebook only) ON | OFF
***200608* Send: software version
***200606* Send: software version
***200806* Send: flex version
***250* / ***251* Keypad tones ON | OFF
***470* Select time format
***500* /***501* Prepaid Balance Display ON | OFF
***520* Change language
Service codes Motorola:
C113, C114, C115, C115i, C116, C117, C118 software version: #02#*
C138, C139, C140 software version: #02#*
C155, C156, C157 software version: #02#*
C257, C261 software version: #02#*
V171, V172, V173 software version: #02#*
V175, V176, V176 software version: #02#*
C168, W220 software version: *#**837#
W208, W375 software version: #02#*

Samsung Phone Code-004

2010-12-19T20:26:00.001-08:00

*2767*3855# - FULL E2P RESET
*2767*2878# - CUSTOM E2P RESET
#*7337# - UNLOCK
*2767*688# - UNLOCK
*#0523# - CONTRAST
*#9998*523# - CONTRAST
*#8999*8378# - Service Menu (X100

Panasonic Phone Codes-003

2010-12-19T20:25:00.001-08:00

*01763*737381# - master reset (user data, user code) A100, A101, A102,G50, G51, G70, GD55..
*369#(*) - MENU

7, 4, 6, menu, menu - lock menu
*#9999# - 5 sec after power on - SW version (GD75, GD67, GD87..)

Motorola Phone Codes

2010-12-19T20:24:00.003-08:00

(T190, T191, T205) master code
- 19980722
- 20010903
**********
P2K test menu:
*#06#, menu, menu, 048263*

Test comands:
32*116*1*0*0 - read phone code
32*118*1*0*0 - read security code
18*0 - factory reset, phone code off
18*1 - master reset
54*18*1 - full phone reset
10*0*6 - select 900/1800
32*279*1*0*8 - model
32*383*1*0*0 - flex version

Hard reset MPX200, MPX220 - blue button + power on

Misobishi Phone Codes-002

2010-12-19T20:24:00.001-08:00

*65512890 (*-hold) format FFS (Eclipse)
* 3926 - (*-hold) test mode
* 5806 - (*-hold) SW version
*(hold) 787090 - trium 320 unlock menu

Misobishi Phone Codes

2010-12-19T20:23:00.001-08:00

hold * 476989 NS Lock Menu
hold * 482896 CP Lock Menu
hold * 574243 NS Lock Menu
hold * 967678 SP Lock Menu
hold * 362628 IMSI Lock Menu
hold * 787090 Lock net.level
hold * 787292 Lock net.level
hold * 3926 Shut Down...

*#0048# fast change polish langpack
*0000# automatic language

*850696 Warmstart

Eclipse:

hold * 65512890 eeprom reset - cure for hangs ect.

Maxon Codes

2010-12-19T20:22:00.003-08:00

*#9922# - menu, reset (without SIM)
*#9900# - Software Version
*#9901# - Software Version (PBatch)

LG Phone Code -003

2010-12-19T20:22:00.001-08:00

2945#*# - service menu (code reset)(W3000 G5300 C1200 G7100...)
2945#(*)- hold (LG 500,600)
B1200 *+pwr, 6,6,8 Service Menu
B1300 *+pwr, 1,5,9 Service Menu

Security Removing Code For Lg 8110,8120.
47328545454#
Or
277634#*#

Huawai Phone Codes

2010-12-19T20:21:00.003-08:00

MASTER SECURITY CODE
-309296
-3092
-9296

FlyBird Codes

2010-12-19T20:21:00.001-08:00

S688 - #*301#02# send - with SIM
menu:
7 - 10 - ok,

#*8000#, #*3676# (reboot repair)

V09, S1180 - *, 3 times down, 3 times up - service menu

Enol Phone Codes

2010-12-19T20:20:00.002-08:00

*#987*00# - Service menu
*#987*99# - Full reset
*#900# - SW version

Alcatel Phone Codes

2010-12-19T20:20:00.000-08:00

Master Codes
- 25228352
- 25228353
- 83227423 (TH3/4,BH4,BF5,BG3,BF3/4..)
###337*07# - master reset (with SIM)
###847# - factory reset (with SIM)
Alcatel 835 formating - **0102#

Mix Phone Code-04

2010-12-19T20:17:00.001-08:00

for innostream:*741*7373868# reset ok

SHARP SECRETS CODES
*01763*8371# (*01763*VER0#) — Firmware Version.
*01763*3641# (*01763*ENG1#) — Enable Engineer Mode hold pwr key to leave then disable.
*01763*3640# (*01763*ENG0#) — Disable Engineer Mode.
*01763*8781# (*01763*TST1#) — Test #1 (test early wdt looping to dump, need to remove battery from phone)
*01763*8782# (*01763*TST2#) — Test #2 (test irq dis looping to switch, resets itself)
*01763*8783# (*01763*TST3#) — Test #3
*01763*8784# (*01763*TST4#) — Test #4
*01763*8785# (*01763*TST5#) — Test #5
*01763*87872# (*01763*TST72#) — Test #72
*01763*8788# (*01763*TST8#) — Test #8
*01763*5640# (*01763*LOG0#) — Disable LOG
*01763*5641# (*01763*LOG1#) — Enable LOG
*01763*4634# (*01763*IMEI#) — IMEI
*01763*6370# (*01763*MEP0#) — Disable MEP menu (unlock menu)
*01763*6371# (*01763*MEP1#) — Enable MEP menu (unlock menu) (go to settings,security,meplocks select insert handset code,default is 0000, allows to check lock status and disable locks only if u have correct code dont try guessing!!)
*01763*63866330# (*01763*NETMODE0#) — Disable NetMode
*01763*63866331# (*01763*NETMODE1#) — Enable NetMode
BENQ-SIEMENS SECRETS CODES
Software version:
*#06#
to see more info, press softkey again
English menu:
*#0001#
Deutsch menu:
*#0049#
Secret Code:
*#0606# remove sim card before
Unlock Sim:
*#0003*(secret code)#
Bonus Screen:
*12022243121
Factory settings: Type *#9999# to reset factory settings.(not tested).
LG SECRETS CODES
LG all models test mode: Type 2945#*# on the main screen.
2945*#01*# Secret menu for LG
IMEI (ALL): *#06#
IMEI and SW (LG 510): *#07#
Software version (LG B1200): *8375#
Recount cheksum (LG B1200): *6861#
Factory test (B1200): #PWR 668
Simlock menu (LG B1200): 1945#*5101#
Simlock menu (LG 510W, 5200): 2945#*5101#
Simlock menu (LG 7020, 7010): 2945#*70001#
Simlock menu (LG 500, 600): 2947#*
LG-U81XX SPECIAL CODES
Code to read phone version :
- Phone without SIM
- Enter 277634#*# or 47328545454#
- Select ‘SW Ver.info’
Code to reset phone :
- Phone without SIM
- Enter 277634#*# or 47328545454#
- Select ‘Factory Reset’
Code to enter UNLOCK MENU :
- Phone wit SIM inside
- Enter 2945#*88110#
Test Menu 8330 : 637664#*#
Test Menu 8180 V10a: 49857465454#
Test Menu 8180 V11a: 492662464663#
Test Menu 8130-8138: 47328545454#
Test Menu 8110-8120: 277634#*#
SAMSUNG SECRETS CODES
Software version: *#9999#
IMEI number: *#06#
Serial number: *#0001#
Battery status- Memory capacity : *#9998*246#
Debug screen: *#9998*324# - *#8999*324#
LCD kontrast: *#9998*523#
Vibration test: *#9998*842# - *#8999*842#
Alarm beeper - Ringtone test : *#9998*289# - *#8999*289#
Smiley: *#9125#
Software version: *#0837#
Display contrast: *#0523# - *#8999*523#
Battery info: *#0228# or *#8999*228#
Display storage capacity: *#8999*636#
Display SIM card information: *#8999*778#
Show date and alarm clock: *#8999*782#
The display during warning: *#8999*786#
Samsung hardware version: *#8999*837#
Show network information: *#8999*638#
Display received channel number and received intensity: *#8999*9266#
*#1111# S/W Version
*#1234# Firmware Version
*#2222# H/W Version
*#8999*8376263# All Versions Together
*#8999*8378# Test Menu
*#4777*8665# GPSR Tool
*#8999*523# LCD Brightness
*#8999*377# Error LOG Menu
*#8999*327# EEP Menu
*#8999*667# Debug Mode
*#92782# PhoneModel (Wap)
#*5737425# JAVA Mode
*#2255# Call List
*#232337# Bluetooth MAC Adress
*#5282837# Java Version
Type in *#0000# on a Samsung A300 to reset the language
Master reset(unlock) #*7337# (for the new samsungs E700 x600 but not E710)
Samsung E700 type *#2255# to show secret call log (not tested)
Samsung A300, A800 phone unlock enter this *2767*637#
Samsung V200, S100, S300 phone unlock : *2767*782257378#
MOTOROLA SECRETS CODES
IMEI number:
*#06#
Code to lock keys. Press together *7
Note: [] (pause) means the * key held in until box appears.
Select phone line - (use this to write things below the provider name):
[] [] [] 0 0 8 [] 1 []
Add phonebook to main menu:
[] [] [] 1 0 5 [] 1 []
Add messages to main menu:
[] [] [] 1 0 7 [] 1 []
Copy SIM memory (phonebook menu):
[] [] [] 1 0 8 [] 1 []
Eng Field options (main menu):
[] [] [] 1 1 3 [] 1 []
Slow (Frequency of search menu):
[] [] [] 1 0 1 [] 1 []
Medium (Frequency of search menu):
[] [] [] 1 0 2 [] 1 []
Fast (Frequency of search menu):
[] [] [] 1 0 3 [] 1 []
Enable EFR:
[] [] [] 1 1 9 [] 1 []
Function :
[] [] [] # # # [] 1 []
Change pin:
[] [] [] 0 0 4 [] 1 []
Unblocking using the “puk” number:
[] [] [] 0 0 5 [] 1 []
There are lots of similar codes exist. If you change the last number to 0 you can deactive that code. The 3 digit number at the middle are from 0 to 999. I put the most interesting codes. (EFR):Enhanced Full Rate Codec.
You can change GSM frequencies to 900/1800 by entering the enginnering model. Following the below steps:
enter menu and press 048263* quickly, then you will enter the secret engineering menu
under “Opcode”
input 10*0*3 for GSM 900
10*0*4 for GSM 1800
10*0*5 for GSM 1900
10*0*6 for dual band GSM 900/1800
10*0*7 for dual band GSM 850/1900
To add extra message space 4 your Motorola C350 C450 C550 or C650, press menu button, press 048263* quickly, then on the popup menu enter 47 press ok.press 50 and ok.press 1 ok.press 64 ok.press 1 ok.press 186 and ok.You will receive an extra 50 msgs memory space.Switch phone off and back on.(not tested)
SONY ERICSON SECRETS CODES
Sony Ericsson Secret Menu: -> * <- <- * <- *
(-> means press joystick, arrow keys or jogdial to the right and <- means left.)
You’ll see phone model, software info, IMEI, configuration info, sim lock status, REAL time clock, total call time and text labels.
You can also test your phones services and hardware from this menu (main display, camera, LED/illumination, Flash LED, keyboard, earphone, speaker, microphone, radio and vibrator tests)
IMEI Number: *#06#
Lockstatus: <- * * <-
Shortcut to last dialed numbers: 0#
Shortcut to sim numbers: On main menu type a number and press #
If you change the language from default to any other language, then it may be difficult to switch to default language. The shortcut is very simple. Just press < 0000 > . < stands for left arrow button or joystick and > stands for right arrow button or joystick.
NOKIA SECRETS CODES
On the main screen type
*#06# for checking the IMEI (International Mobile Equipment Identity).
*#7780# reset to factory settings.
*#67705646# This will clear the LCD display(operator logo).
*#0000# To view software version.
*#2820# Bluetooth device address.
*#746025625# Sim clock allowed status.
*#62209526# - Display the MAC address of the WLAN adapter. This is available only in the newer devices that supports WLAN like N80
#pw+1234567890+1# Shows if sim have restrictions.
*#92702689# - takes you to a secret menu where you may find some of the information below:
1. Displays Serial Number.
2. Displays the Month and Year of Manufacture
3. Displays (if there) the date where the phone was purchased (MMYY)
4. Displays the date of the last repair - if found (0000)
5. Shows life timer of phone (time passes since last start)
*#3370# - Enhanced Full Rate Codec (EFR) activation. Increase signal strength, better signal reception. It also help if u want to use GPRS and the service is not responding or too slow. Phone battery will drain faster though.
*#3370* - (EFR) deactivation. Phone will automatically restart. Increase battery life by 30% because phone receives less signal from network.
*#4720# - Half Rate Codec activation.
*#4720* - Half Rate Codec deactivation. The phone will automatically restart
If you forgot wallet code for Nokia S60 phone, use this code reset: *#7370925538#
Note, your data in the wallet will be erased. Phone will ask you the lock code. Default lock code is: 12345
Press *#3925538# to delete the contents and code of wallet.
*#7328748263373738# resets security code.
Default security code is 12345
Unlock service provider: Insert sim, turn phone on and press vol up(arrow keys) for 3 seconds, should say pin code. Press C,then press * message should flash, press * again and 04*pin*pin*pin#
Change closed caller group (settings >security settings>user groups) to 00000 and ure phone will sound the message tone when you are near a radar speed trap. Setting it to 500 will cause your phone 2 set off security alarms at shop exits, gr8 for practical jokes! (works with some of the Nokia phones.)
Press and hold “0″ on the main screen to open wap browser.

Mix Phone Codes -03

2010-12-19T20:16:00.001-08:00

Alcatel
Master Codes
- 25228352
- 25228353
- 83227423 (TH3/4,BH4,BF5,BG3,BF3/4..)

###337*07# - master reset (with SIM)
###847# - factory reset (with SIM)
###728# - factory reset (with SIM)

Alcatel 835 formating - **0102#

Samsung
*2767*3855# - FULL E2P RESET
*2767*2878# - CUSTOM E2P RESET
#*7337# - UNLOCK
*2767*688# - UNLOCK
*#0523# - CONTRAST
*#9998*523# - CONTRAST
*#8999*8378# - Service Menu (X100)

Philips

#20021208# ok - 630 without SIM (erase flash)
*#7728*# - RSAV DONE
*#3849*# - ??? reboot
*#3851*# - ??? reboot
Philips 568 *01763*737381# - reset

Pantech
*01763*737381# - master reset (user data, user code) without SIM
*01763*8371# - SW version
*01763*6371# - UNLOCK
*01763*3641# - Menu

Panasonic

*01763*737381# - master reset (user data, user code) A100, A101, A102,G50, G51, G70, GD55..
*369#(*) - MENU

7, 4, 6, menu, menu - lock menu
*#9999# - 5 sec after power on - SW version (GD75, GD67, GD87..)

LG
2945#*# - service menu (code reset)(W3000 G5300 C1200 G7100...)
2945#(*)- hold (LG 500,600)
B1200 *+pwr, 6,6,8 Service Menu
B1300 *+pwr, 1,5,9 Service Menu

Security Removing Code For Lg 8110,8120.
47328545454#
Or
277634#*#

Sony-Ericsson
> * < < * < * - Service menu

< * * < - Lock menu

VK Mobile

*#79# - SW version
*#85*364# (*) - hold menu
855855# without SIM (VG107)
85558555#(*)-hold
4268#(*)-hold (VG207)

Voxtel
0124 - master code
0718#(*)- hold - menu (ST11, SC10, V100 without SIM)
4268#(*)- hold - show code (ST11, SC10 without SIM)
*789(#)- hold - menu (V50, V300, RX100 without SIM)

Motorola
(T190, T191, T205) master code

- 19980722

- 20010903

**********

P2K test menu:
*#06#, menu, menu, 048263*

Test comands:
32*116*1*0*0 - read phone code
32*118*1*0*0 - read security code
18*0 - factory reset, phone code off
18*1 - master reset
54*18*1 - full phone reset
10*0*6 - select 900/1800
32*279*1*0*8 - model
32*383*1*0*0 - flex version

Hard reset MPX200, MPX220 - blue button + power on

Nokia
*#7370925538# (valet code reset) 6230
*#746025625# [*#sim0clock#]
*#92702689# [*#war0anty#]

Fly Bird
S688 - #*301#02# send - with SIM
menu:
7 - 10 - ok,

#*8000#, #*3676# (reboot repair)

V09, S1180 - *, 3 times down, 3 times up - service menu

Enol
*#987*00# - Service menu
*#987*99# - Full reset
*#900# - SW version

Maxon
*#9922# - menu, reset (without SIM)
*#9900# - Software Version
*#9901# - Software Version (PBatch)

S60 Siries (SX1, 6600, N-Gage..)
*#7780# - factory default
*#7370# - full factory defaults (all user data reset)
SX1 formating - * + # + power on
6600 formating - 3 + * + send + power on
Sendo X1 formating - 5 + power on

Mitsubishi
*65512890 (*-hold) format FFS (Eclipse)

* 3926 - (*-hold) test mode

* 5806 - (*-hold) SW version

*(hold) 787090 - trium 320 unlock menu

Huawei (cdma)

MASTER SECURITY CODE
-309296
-3092
-9296

Pantech HX-550C (cdma)

Full reset (phone code reset)- ##03*934#9367*192#397#7412569746 PWR,
after reset - ##27732726 PWR and select "with uim"

CDMA Codes 2

2010-12-19T20:15:00.002-08:00

AUDIOVOX 7900
Menu # (cl. envelope) * 1

AUDIOVOX 8610/8910
## 8ya"yaya'(Vykl) password 000000 or 111111 (standard SPC 072096 - for 8910)

AUDIOVOX 8910
for the output of telephone from the service- regime ## of 27752345 vkl

AUDIOVOX 8910
for the output of telephone from the service- regime ## of 737247 vkl

AUDIOVOX FT 3200
yashch'80*ya"*8'9#y

COMPAL
** 321456987 ##

EPSILON
** 321456987 ##, ** 3214569871472365 ## the removal of lok of the code

Kyocera Kx-2
111111 (then right smart of key)

LG DM510/DM150
menu 3 0 further code

LG SV590
Menu 0, SPC code: 852456
a -key: * shchya??'2*2shche9 *

LG 2130/2230
# shchya??'2#*shchya??'2 *

LG VX3200
Menu-0(000000)

LG VX9800(.the V)
on the large keyboard to harvest button Sym, 3477247, CLR, CLR, 1

LG 5130
# shchya??'2#*"eshchye0 *

LG 6130
# shchya??'2#*"e'ye0 *

LG 5550 codes of the access into the engineering menu
## 7764726 save

Password on LG Pm -325
the engineering menu: ## 2342 #

opening window AKEY: ## 2539 #

NOKIA 3586i
* e00y#y??yashch #

NOKIA Sprint
## 3282 #

NOKIA 8587
* # '2'#""'ya"2' #

SKY 1400/3000/5000/5100/shchya00(Izrail')
# "shch8eshche8e2ya#'2' #

SKY 5400 (Korean prosh.) / 6100/6200
* "shch9#'2'*"e88ya'ya #

SKY 6400
* "shch9#e'ya*"e88ya'ya

SAMSUNG A740 (BELL)/.A8'0 (BELL)
## 675 ok

SAMSUNG A530/A620/N195/N356
menu 6 *

SAMSUNG N362(Izrail6)
yae'"90shch#*y0*#*9ye'20

SAMSUNG A460/N240/A500/N400
## 000000

SAMSUNG A610
menu 9 *

SAMSUNG A630
menu 5 *

SAMSUNG A300/N105/A100/A562/A611
ya"*8'9#08#9 and menu 60

SAMSUNG A560
## 3282 #

SAMSUNG A660
menu ## 000000 ok and ## 3282 ok

SAMSUNG A670
menu 7 2 * (000000)

SAMSUNG A680
## 000000 ##

SAMSUNG A790
menu 0 and menu 2 0

SAMSUNG A860
menu, setting *

SAMSUNG X, E, V- series
'shchya8#0**ya#' and ya"*8'9#08#9 and 74153697193

SAMSUNG E300
741 53 697 193

SONY ERICSSON T608
923885 pointer to the right

TELSON TDS 320
menu 4 0 000000

MOTOROLA V710/V265
menu 073887 * (rapidly)

MOTOROLA V8160
FCN 13 times of tsifra"0" RCL

Kod access to Motorola RAZR V3 (americ)
# 073887 *

Password on MOTOROLA without and - Kay
5 7 5 9 7 8 9 * # then the button of the camera of 3 times (code 915037)

To make a complete discharge on MOTOROLA V8160
FCN 00**8e"8''ee STO further 32 # 01 #

MODOTTEL (Withus) W100/200/300
## 948487 ok

TOSHIBA 9100/9155/9500
In the flow 10 s. after switching on 289 fcn #y

As to introduce A -key code
HYUNDAI 310/610: 2539 menu menu
NOKIA 3586/3588 2539 end end
Many dr.modeli 2539 **

New Codes

2010-12-19T20:15:00.000-08:00

Samsung sph-n240, n400, a460, a500, etc Nam Programming:

Nam Set: ##Spc

Test Mode: 47*869#1235

Debug Menu: ##33284,ok

Service Menu: Menu+8+0 (#889)

Reset (Life time, Clear Memory, etc): ##786,ok

A-key: ##2539,ok

Label Selection: ##3882,ok

Label(Home, Work, etc) : **523,ok

NGG Setting (Gateway, etc.): ##2769737,ok

Vocoder: ##8626337,ok

CAI Change: ##7738,ok

Enable TTY: ##889,ok

Samsung sch-411, 611, n105, a100, a300, a2000, etc Nam Programming:

Nam Set: 47*869#08#9

Nam Set: Menu+60

Test Mode: *759#813580

Test Mode: 5809540*45680

A-key: Menu+0, 25##

External Audio: Menu+0, ####

Debug Menu: Menu+8, 0415 or Spc

Debug Menu: Menu+9, 0415 or Spc

Brief NAM Programing: Menu+40,626 (not all version)

LCD Contrast: Menu+45 (not all version)

SIO Mode: Menu+49

SIO Mode: Menu+69

Samsung a300, a530, a620, a660, etc Nam Programming:

Nam Set: Menu, 6, *

Service Menu: Menu, 9, *

Test Mode: 47*68#13580

Samsung X, E, V-series, e250, e300, v420, etc Nam Programming:

Nam Set: 6548#0**4#6

Nam Set: 47*869#08#9

Nam Set: 74153697193

Test Mode: 5809540*45680

Debug Menu: Menu(2sec)+0, 6725 or 9720

Samsung i700, etc Nam Programming:

Nam Set: Go to start and select "PHONE" from the drop down menu, dial #83587

Samsung i300, etc Nam Programming:

1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. Enter OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice

TEST MODE COMMANDS:

411_test_mode.txt

811_test_mode.txt

n105_test_mode.txt

n240_test_mode.txt

n260_test_mode.txt

a500_test_mode.txt

a530_test_mode.txt

<>

--------------------------------------------------------------------------------

Qualcomm qcp-800 Nam Pogramming:

Nam Set: Menu+3+0+Spc

Field Test: Menu+7+0+Fsc

Kyocera 1135, 2255, 3035, 5135, 6035, Se47, etc Nam Programming:

Nam Set: 111111+Jog Dial(Ok), Select "Programming"+Spc

CAI Change: ##7738,ok

Enable TTY: ##889,ok

Life Timer, PRL, etc: ##786,ok

A-key: ##2539,ok

A-key: 2539,ok

<>

--------------------------------------------------------------------------------

Sanyo 4900, 5150, 5300, 8100, etc Nam Programming:

Nam Set: ##Spc+Ok+Key Down+Ok

A-key: ##2539+Ok+Key Down+Ok

Version: ##**837+Ok+Key Down+Ok

Debug Menu: ##FSC+Ok+Key Down+Ok

Airtime menu: ##8463+Ok+Key Down+Ok

Change CAI: ##7738+Ok+Key Down+Ok

Vocoder: ##8626337+Ok+Key Down+Ok

Reverse Logistic: ##786+Ok+Key Down+Ok

Set IP Address: ##2769737+Ok+Key Down+Ok

TTY On/Off: ##889+Ok+Key Down+Ok

Advanced Data: ##3282+Ok+Key Down+Ok+Msl

Ready Link: ##4636+Ok+Key Down+Ok

Browser Init On/Off: ##4682+Ok+Key Down+Ok

Picture Token: ##25327+Ok+Key Down+Ok

Unknown Code: ##5282277+Ok+Key Down+Ok

(SPC=000000, FSC=040793)

Sanyo scp-A011, smp-A017, etc Nam Programming:

Nam Set: F9(3 beep) + 0*72696#767

<>

--------------------------------------------------------------------------------

Nokia 3280, 3285, 3580, 3585, 5185, 6185, 8280, etc Nam Programming:

Nam Set: *3001#12345#

Software Version: *#837#

Software Version: *#9999#

Esn Number: *#92772689#

Restart Phone: *#75681#

Restart Phone: *#75682#

Nokia 8887 Nam Programming:

Nam Set: *3001#12345#

Version: *#0000#

Evrc: *#8378#

Esn/Data/Timer: *#92772689#

SID: *#743#

Nokia 8587 Nam Programming:

Nam Set: *#626#7764726#

A-Key: #8159357022#4579# (26 digits)

A-Key: #8159357022#4547# (20 digits)

Version: *#0000#

Version: *#837#

Vocoder: *#3872#

Change language: Menu 5, 3, 1

Change DM mode: *#7678#

Debug Screen: *#8378#

Debug: *#8380#

Field Test Menu: *#83788#

SPC Unlock, Factory Reset:

Full Factory Reset: *#7370#

Resets all settings including non-user changeable items (like SPC)

NOKIA TEST MODE:

51xx, 61xx, 71xx, 3285, 63xx, etc:

1) Turn on the phone. Press *3001#12345#

2) Scroll up to where it says "Field Test" and choose SELECT

3) Highlight "Enable" and choose OK. Turn the phone off then back on.

4) If the test mode screen does not show up press MENU and scroll

    down to "Field Test" choose SELECT. Press 0 1 then choose OK.

5) Lower left or upper left number is the signal strength.

6) To turn off the test mode press MENU and scroll down to where it says

    "Field Test" choose SELECT. Press 0 0 and then choose OK.

3360, 6360:

1) Turn on the phone. Press *3001#12345#

2) Scroll up to where it says "Field Test" and choose SELECT

3) Highlight "Enable" and choose OK. Turn the phone off then back on.

4) If the test mode screen does not show up press MENU and scroll

    down to "Field Test" choose SELECT. Press 2 1 0 1 then choose OK.

5) Lower left or upper left number is the signal strength.

6) To turn off the test mode press MENU and scroll down to where it says

    "Field Test" choose SELECT. Press 2 1 0 0 and then choose OK.

<>

--------------------------------------------------------------------------------

Audiovox 4000, 9000, 9100, 9155, 9500, etc Nam Programming:

(Power the phone on and wait until the little light on top goes out)

Nam Set: 289+fcn+#+1

Service menu: fcn+00+fsc(000000)

Test Mode: Hold (2,*,Rcl)+Power

Test Mode Commands:

99 - download - flash phone
124 - inam data write
125 - version
126 - esn read
127 - sec_code
128 - lock_code

129 - is WFTV data write
137 - FSC code
138 - NPcode (nam program code)
139 - dscode
141 - restart
218 - Read_Addr
000 - is cdma mode
001 - is fm mode
002 - is pcs mode
008 - is reg read addr
020 - is lna_range

Audiovox pcx-3500xl Nam Programming:

Nam Set: ##2726+Send+1998+1+Spc+1

Audiovox cdm-100, 130, 135, 8300, 8500, 8600, etc Nam Programming:

Nam Set: ##20022002+Pwr+1+Spc

Audiovox 8610, 8910, etc Nam programming:

Name Set: ##847446, end, 111111

Audiovox-107 Nam Programming:

Nam Set: 45680*47*869#1

Audiovox 9950 Nam Programming:

Nam Set: ##3282

Audiovox Z800 (Audiovox 7900, Sharp) Nam Programming:

Nam Set: m + # + envelope key + * + 1

Audiovox Thera (Toshiba 2032) Nam Programming:

Thera Nam Programming User Manual - nam_thera.pdf

AUDIOVOX TEST MODE:

9100, 9155:

1) Turn on the phone. As soon the phone comes on and the green light

     turns off press RIGHTARROW, 0, 0. The phone will ask for the

     "FSC Code", press 000000 then choose OK and press RIGHTARROW,

     RIGHTARROW. Your phone is now in test mode.

2) The signal strength is the number on the top right hand side of the screen.

3) To turn off test mode shut of the phone and then turn it back on.

<>

--------------------------------------------------------------------------------

Motorola 7760, 7860, 2260, 8160, etc Nam Programming:

Nam Set: Fcn,0000000000000, Rcl

Nam Set: 74663#, Fcn, Fcn

Test Mode: Fcn, 00**83786633, Sto

Motorola v60c, v120c etc Nam Programming:

Nam Set: 74663#, Menu, Menu, Spc

Nam Set: Menu, 073887, * (type quickly)

Test Mode: Menu, 073887*, Spc

Debug Mode: ##33284

Force the phone into DIGITAL ONLY mode:

1) ##33284 (Debug)

2) RIGHT Softkey (Next) Twice

3) Down arrow 10 times to "PrefMod"

4) RIGHT Softkey (Change) until you see "DigOnly"

5) LEFT softkey (Exit)

6) MENU then LEFT Softkey return to idle screen

7) ##33284 (The last 4 will not display if you have done it correctly)

Motorola t182, c210, etc Nam Programming:

Nam Set: ##1111 end

Nam Set: ##298645665 end

Short Nam: ##073887 sto

Motorola v710, v730, v740, ms150, etc Nam Programming:

Nam Set: 8378*# + press 3 times NATE (spc - 071082)

Test Mode: Menu, 073887*, Spc

Service Menu: #758353266#646#

Motorola StarTac 2004 Nam Programming:

Nam Set: 5759789*#, rec key (3)times (spc - 915037)

Motorola ms200, ms230, etc Nam Programming:

Nam Set: 5759789*# (spc - 915037)

Motorola v6060 Nam Programming:

Nam Set:147*369#456*0#

MOTOROLA TEST MODE:

v60, c120, c331, etc:

1) Turn on the phone. Press MENU 0 7 3 8 8 7 *

2) The phone will require you to "Enter a Security Code", press 000000, OK

3) Scroll down to "Test mode" choose SELECT. Scroll down to "Enable"

    choose SELECT. Your phone is now in test mode.

4) Signal strength is the 3_rd number down on the left hand side of the screen.

5) To toggle between regular mode and test mode: Press MODE then

    quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.

6) To turn off the test mode the phone must be in regular mode, then follow

    the above sequence and scroll down to where it says "DISABLE" instead of

    "ENABLE" and choose select.

Motorola Bible - bible.txt

<>

--------------------------------------------------------------------------------

lgc-300, etc Nam Programming:

Nam Set: Menu, 9, Spc

A-key: Press "Sto" 3sec, 2539**

lgc-330w, etc Nam Programming:

Nam Set: Menu, 4, 0, Spc

A-key: 2539**

lgc-510, v111, etc Nam Programming:

Nam Set: Menu, 3, 0, Spc

A-key: 2539**

lgc-500, 800w, etc Nam Programming:

Nam Set: Menu, 9 , 0, Spc

Debug Mode: Menu, 7, 0, Fsc

Debug Mode: Menu, 8, 0, Fsc

A-key: 2539**

Lg LX,VX-series, VX4400, VX6000, etc Nam Programming:

Nam Set: ##Spc

Nam Set: Menu, 0

Advanced Settings: ##2342

Vocoder: ##8626337,ok

CAI Change: ##7738,ok

Enable TTY: ##889,ok

A-key: ##2539,ok

Reset (Life time, Clear Memory, etc): ##786,ok

<>

--------------------------------------------------------------------------------

Sky All Models Nam Programming:

Nam Set: #7583538324#626#

Test Mode: #7583538324#8378#

Service Menu: Menu+4+0+Spc

Service Menu: Menu+5+0+Spc

<>

--------------------------------------------------------------------------------

Withus wce-100, 200, 300, etc Nam Programming:

Nam Set: ##948487+Save

Nam Set: ##948482+Save

wce-200 ESN write: ##66835+Save

(At the first programming)

<>

--------------------------------------------------------------------------------

Hyundai hwp-110 Nam Programming:

Nam Set: #86904**89397#

DM Mode: ##2740*

(Open phone, inter code, close phone)

Hyundai hgc-120, 130, 200 Nam Programming:

Nam Set: #86904**89397#

Hyundai hgc-310, 600, 610 Nam Programming:

Nam Set: ##20022002+Pwr+1+Spc Code

Field Test: ##20022002+Pwr+1+Master Code

Hyundai Curitel h-100, 150, hx-510b, 520 Nam Programming:

Nam Set: ##20022002+Pwr+1+Spc Code

Field Test: ##20022002+Pwr+1+Master Code

A-key: 2539**

Debug Menu: ##27732726+Pwr

Sar Test: ##27752345+Pwr

Baud Rate: ##36**+Pwr

DM Mode Enable: **1004+Pwr

DS Mode Enable: **1005+Pwr

Test Bell/Voice/Led/Dot: ##1122+Pwr

RF Mode: ##2240+Pwr

Ras Ram: ##2774+Pwr

Cmux1: **0481+Pwr

Cmux2: **0482+Pwr

RX Mode Fax: **0492+Pwr

RX Mode Data: **0491+Pwr

RX Mode Reset: **0490+Pwr

<>

--------------------------------------------------------------------------------

Huawei ETS-668, 678, 688, etc Nam Programming:

Debug Mode: ##44+Menu

Debug Screen: ##33+Menu

CDG2 Test enable: ##234+Menu

CDG2 Test disable: ##432+Menu

China Lang Select: ##123+Menu

Blocking Debug Code: ###888+Menu

Home System Only On: ##461+Menu

Home System Only Off: ##460+Menu

<>

--------------------------------------------------------------------------------

Ericsson A1228c, T61, etc Nam Programming:

Short NAM: 987+Menu

Long NAM: 923885+Menu+Spc

CDMA Mode: 904093+Menu

Analog Mode: 904095+Menu

QNC: 904097+Menu

Debug Screen: 904090+Menu

DM Mode: 904050+Menu

Sony-Ericsson T608 Nam Programming:

Nam Set: 923885, Joystick to the right, 111111

<>

--------------------------------------------------------------------------------

Epsilon vc-5x Nam Programming:

Nam Set: **147258963##

Programming1: **1232580##

Programming2: **321456987##

Version: **1470963##

Debug: **000000##

Menu_1: **078987##

Menu_2: **1234756##

A-key: 2539**

Reset: **14789##

<>

--------------------------------------------------------------------------------

Z510, Z710i(gcd-456) Nam Programming:

Nam Set: Menu+0+Spc

<>

--------------------------------------------------------------------------------

AMC450 Nam Programming:

Nam Set: *74269#*748#96148063+SEL

<>

--------------------------------------------------------------------------------

Gtran gcp-2000 Nam Programming:

Nam Set: 01#737+Spc

Debug Menu: 01#324+Spc

Debug Mode: 01#727

Test Mode: 01#764+Spc

System Test Mode: 01#768+Spc

Gtran gcp-5000 Nam Programming:

Debug Mode: 01#727+Spc

Test Mode: 01#765

<>

--------------------------------------------------------------------------------

PANASONIC TEST MODE:

Panasonic (Most):

1) Turn on the phone. Press #7764726# choose SEND

2) Scroll down to where it says "NAM 1" and choose OK. Scroll down

    to "Access To Level 4" choose YES. Scroll down to "Built-In-Monitor"

    and choose EDIT.

3) Press 1 and choose OK then choose BACK. The phone will say

    "Back To Level 1" choose YES. Now choose EXIT the phone will ask you

    "Exit And Save Change" choose YES.

4) Signal strength is the top right number on the screen.

5) To turn off the test mode follow the above sequence except press 0

    instead of 1 at the "Built-In-Monitor"

<>

--------------------------------------------------------------------------------

Synertek S200 Nam Programming:

Nam Set: Menu+0+Spc

Debug Mode:

Test vibro/rx/tx: ##5555+Save

Debug Screen: ##33+Save

Debug Screen: ##523+Save

RF Test: ####+Save

Unknown code: ##325+Save

<>

--------------------------------------------------------------------------------

Sony CM-M1300, 3300, Z200 Nam Programming:

Nam Set: 111111+Ok(Jog Dial)+Select+Programming+Ok+Spc

Mix Phone Codes

2010-12-19T20:10:00.000-08:00

Do you want to know what version of SW do you have in phone? IMEI number?
Below you have got secret codes for your cellphone. With this codes you can without any problem check IMEI, software version, reset to default language or deactivate simlock (only in some models). Some of codes that you got below must by typed without SIM card in cellphone and some with SIM card in phone. Please be cerfull - with some codes you may PERMENANTLY block your cellphone.

Alcatel

IMEI number:    * # 0 6 #
Software version:    * # 0 6 #
Net Monitor:    0 0 0 0 0 0 *

Bosch
IMEI number:    * # 0 6 #
Dafault Language:    * # 0 0 0 0 #
Net Monitor:    * # 3 2 6 2 2 5 5 * 8 3 7 8 #

Dancall
IMEI number:    * # 0 6 #
Software version:    * # 9 9 9 9 #
SIMcard serial number:    * # 9 9 9 4 #
Information about battery status:    * # 9 9 9 0 #
Selftest (only Dancall HP2731):    * # 9 9 9 7 #
Show version configuration:    * # 9 9 9 8 #
Net Monitor:    * # 9 9 9 3 #

Ericsson
IMEI number:    * # 0 6 #
Software version:    > *
Dafault Language:
Enter to phone menu without SimCard - after Wrong PIN:    press NO:
* * 0 4 * 0 0 0 0 * 0 0 0 0 * 0 0 0 0 #
Information about SIMLOCK:

Hagenuk
IMEI number:    * # 0 6 #
Software version:    # # 9 1 4 0 * 8 3 # 7 5 * 2 #
Mitsubishi
View IMEI:>     * # 06 # View IMEI

Default language English:    * # 0044 # English

JDefault language Deutch:    * # 0049 # Deutsch

NetMonitor1 activate:    hold * enter 4329

NetMonitor2 activate:    hold * enter 621342

Enter into M4 Test mode:    hold * enter 5472

Show SW version:    hold * enter 5806

Show HW version:    hold * enter 5807

Show SW and HW version:    hold * enter 936505

NS Lock Menu:    hold * enter 476989

CP Lock Menu:    hold * enter 482896

NS Lock Menu:    hold * enter 574243

SP Lock Menu:    hold * enter 967678

IMSI Lock Menu:    hold * enter 362628

Lock net.level:    hold * enter 787090

Lock net.level:    hold * enter 787292

Shut Down:    hold * enter 3926
Motorola
IMEI number:    * # 0 6#
Net Monitor ON:    * * * 1 1 3 * 1 * [OK]
Net Monitor OFF:    * * * 1 1 3 * 1 * [OK]
* - press this until box shown up

Nokia
IMEI number:    * # 0 6 #
Software version:    * # 0 0 0 0 # lub * # 9 9 9 9 #
Simlock info:    * # 9 2 7 0 2 6 8 9 #
Enhanced Full Rate:    * 3 3 7 0 # [ # 3 3 7 0 # off]
Half Rate:    * 4 7 2 0 #
Provider lock status:    # p w + 1 2 3 4 5 6 7 8 9 0 + 1
Network lock status:    # p w + 1 2 3 4 5 6 7 8 9 0 + 2
Provider lock status:    # p w + 1 2 3 4 5 6 7 8 9 0 + 3
SimCard lock status:    # p w + 1 2 3 4 5 6 7 8 9 0 + 4
1234567890 - MasterCode which is generated from IMEI

Philips
IMEI number:    * # 0 6 #
Simlock info:    * # 8 3 7 7 #
Security code:    * # 1 2 3 4 # (Fizz) or * # 7 4 8 9 #

Samsung
IMEI number:    * # 0 6 #
Software version:    * # 9 9 9 9 # albo * # 0 8 3 7 #
Net Monitor:    * # 0 3 2 4 #
Chaning LCD contrast:    * # 0 5 2 3 #
Memory info:    * # 0 3 7 7 # albo * # 0 2 4 6 #
Reset memory (SIMLOCK`a removing!!!):    * 2 7 6 7 * 3 8 5 5 #
Reset CUSTOM memory:    * 2 7 6 7 * 2 8 7 8 #
Battery state:    * # 9 9 9 8 * 2 2 8 #
Alarm beeper:    * # 9 9 9 8 * 2 8 9 #
Vibra test:    * # 9 9 9 8 * 8 4 2 #

Sagem
IMEI number:    * # 0 6 #
Service Menu access:    MENU 5 1 1 #
Siemens
IMEI number:    * # 0 6 #
Software version:    put off sim card and enter:: * # 0 6 # (and press LONG KEY)
Bonus screen:    in phone booke: + 1 2 0 2 2 2 4 3 1 2 1
Net Monitor (S4 Power):    Menu 9 8, left SoftKey, 7 6 8 4 6 6 6, Red phone, Menu 5 6

Sony
IMEI number:    *#06#
Software version:    *#8377466#
Show list of product creator names:    (you must save this number in your Phone Book with "own phone no." record): + 1 2 0 2 2 2 4 3 1 2 1

Code for Z500!

2010-12-19T20:06:00.001-08:00

Code for Z500!

1- Enter code *7465625*28782# without a sim in the phone
2- Phone will display "Auto Subset Lock: Activated!"
3- Enter code *7465625*28638# without a sim again
3- Phone will display "Auto Network Lock: Activated!"
4- Now insert the sim and enjoy! Phone is Unlocked!

z500v unlockin codes

hi ive ive unlocked my samsung z500v using the codes
*7465635*28782#
*7465625*28638#

All CDMA Phones secret Codes

2010-12-19T20:05:00.001-08:00

all cdma secret codes

Samsung:
All type of phones (old modeles):
NAM programming: 47*869#08#9
Test mode: *759#813580 or 5809540*45680
exit test mode - 02
A-Key: menu + 0, code 25##
Samsung A500

1. Enter ## and the 6 digit OTKSL
2. SERVICE MENU will appear and 1.Basic will be highlighted
3. Press OK
4. Device will display NAM CDMA/ Phone Number
5. Enter 10 digit MIN
6. Press OK (3 times)
7. Display will return to Service Menu. Press END.
8. Programming is complete
Samsung N240 and N400
1. Enter ## and type in the 6 digit OTKSL
2. The display will show SVC MENU and 1. Phone Number
3. Press OK
4. Enter the 10 digit MIN and press OK
5. The display will show NAM with Home SID on the second line (Note: SID is no longer used)
6. Press OK
7. The display will return to the SVC MENU
8. Press END to complete the programming
Samsung Uproar
1. Press MENU key
2. Enter 9 2 0
3. Enter the OTKSL
4. At SVC Menu screen press OK
5. Enter MIN and press OK 4 times
6. Enter SID (4654) and press OK
7. Press END key
8. Programming is complete
Samsung N300
1. Press ## followed by the OTKSL
2. SVC menu will be displayed
3. Press 1 for Phone #
4. Enter the 10 digit MIN and press OK
5. MIN that was entered will be displayed press OK
6. SVC Menu will display press 3 for NAM
7. Enter the 4 digit Home SID press OK
8. Press END and handset will power cycle
Samsung i300
1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. ENTER OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice
Samsung A400 and A460
1. Enter ## and OTKSL
2. Press 1 for Basic at MENU (1 of Phone # when using the MSL)
3. Enter 10 digit MIN and press OK
4. At 1.Basic Menu press the END key
5. Handset will power cycle
Samsung 3500 8500 6100 N200
1. Press MENU
2. Press 6 0 (3500) 8 2 0 (8500/6100/N200)
3. Enter OTKSL
4. Press 1 at SVC MENU Screen
5. Enter MIN and press OK
6. Press OK 4 times
7. Enter SID (4654) and press OK
8. Press END key
9. Programming is complete

Qualcomm:
QCP-800 programming: menu + 3 + 0.
SPC: "000000" or may be other SPC typed by user.
QCP-820/1920/2035: type "111111" and press Jog Dial.
Choose "Programming" and enter SPC: "000000" or may be other SPC typed by user.
QCP 1960 and 2760
1. Press softkey under the work MENU
2. Press 8 0
3. Enter the OTKSL
4. Press softkey for OK
5. Enter MIN and press softkey for OK
6. No SID is require for this handset
7. Press softkey for EXIT
8. Programming is complete

LG:
LGC-300 programming: menu + 9 and enter SPC: "000000" or may be other SPC typed by user
A-Key: press STO for some time while you can see special code enter zone. Type 2539** and enter A-key
LGC-330W programming: menu + 4 + 0 and enter SPC: "000000" or may be other SPC typed by user.
A-Key: type 2539** and enter A-key
LGC-800W /500 programming: menu + 0 and enter SPC: "000000" or may be other SPC typed by user.
A-Key: type 2539** and enter A-key
LGC-510 programming: menu + 3 + 0 and enter SPC: "000000" or may be other SPC typed by user.
A-Key: type 2539** and enter A-key
LG1010 LG4NE1 TP2200 TP2100 Touchpoint SB/DB TP 1100 TP5200

1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. Scroll to MIN and press OK
5. Enter 10 digit MIN scroll to SAVE and press OK
6. Scroll to SID and press OK (Skip on 4NE1 go to RESET PHONE and press OK to complete)
7. Enter SID (4654) and scroll to SAVE and press OK
8. Programming is complete
LG5350

1. Enter ## and enter the OTKSL and press the left soft key under the word “Save”
2. At the Service Program display select Mobile Phone # and press the OK in the center of the 4 way navigation key
3. Enter the 10 digit MIN and press OK
4. Scroll down to 4. Advanced and press OK
5. Scroll to NMSI and press OK
6. Enter the MSID and press OK
7. Scroll down to 9. Amps Phone # and press OK
8. Enter the MSID and press OK
9. Press the END key
TP 2100
1. Press ##
2. Enter OTKSL
3. Scroll to SAVE and press Roller Ball in for OK (ESN will display)
4. Select NEXT (by pressing in the roller ball)
5. Scroll to EDIT and press in the roller ball
6. Enter MIN
7. Scroll to SAVE and press roller ball in
8. Select NEXT at the next 3 screens and then EXIT
9. Programming is complete
TP3000

1. Press ##
2. Enter OTKSL
3. Scroll to SAVE and press OK
4. Open flip
5. Use Stylus to enter the 10 digit MIN
6. Press OK (No SID entry is required)
7. Programming is complete
TP 5250

1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. The phone display will read SVC Program
5. Scroll to MOBILE PHONE # and press OK
6. Phone display will read Mobile Phone Number
7. Enter the 10 digit MIN and press OK
8. Scroll to Home SID and press OK
9. Enter the 4 digit SID (4654) and press OK
10. Reset Phone will be highlighted. Press OK
11. Phone will reset
12. Programming is complete
LG V111(DM110)
[menu]30.
After ask lockcode, enter: 843691.

Ericsson:
Programming:
Shot NAM 987 + menu
Long NAM 923885 + menu and enter SPC: "000000" or may be other SPC typed by user.
CDMA mode 904093 + menu
Analog mode 904095 + menu DM mode 904959 + menu

Hyundai:
HGC-120E / -130E programming: #86904**89397#
HGC-600E programming: ##20022002, END and enter SPC: "000000" or may be other SPC typed by user.

Sony:
CM-M1300/3300/Z200 programming: type "111111" and press Jog Dial.
Choose "Programming" and enter SPC: "000000" or may be other SPC typed by user.
Sony CM-M1300

1. Power phone on
2. Enter six "1s" ( 111111 )
3. Press the jog dial in
4. Press the jog dial in again to select programming
5. Enter six "0s" for the service security code
6. Phone displays the ESN
7. Press the jog dial in for OK
8. Enter your ten digit cellular telephone number
9. Press the jog dial in for OK
10. Enter your cellular carrier’s system ID (SID) without the zeros
(Example: if your carrier’s system ID is 00035, enter just 35)
11. Press the jog dial in for OK
12. Enter a name for NAM 1 or just press the jog dial in for OK
13. Phone displays Basic NAM 1 Programming is complete
14. Press the jog dial in
15. Press the jog dial in again for EXIT
16. Phone powers itself off
17. Press the power button to power the phone back on
18. Basic programming is complete

Motorola:
StarTAC 7760/7860 programming:
Service menu: FCN+0+000000+000000+RCL
Test mode: FCN 00**83786633 STO
V60c programming:
Service menu: 74663 # [Menu] [Menu] (programming code)
Test mode: [Menu] 073887 * (security code = 000000)
Motorola Tarpon (120x)
1. Press 74663 (spells PHONE)
1. Press # MENU MENU quickly
2. Enter OTKSL
3. The work MIN will be highlighted
4. Select the word CHANGE by selecting the top right button
5. Select DELETE. Press and hold the button until clear
6. Have the customer enter the 10 digit MIN number
7. Select OK with the top right button. The “User Activation” screen will appear
8. Scroll to highlight the CDMA Sys ID
9. Select CHANGE by selecting the top right button
10. Enter SID
11. Select OK by selecting the top right button
12. Select DONE with the top left button
13. Press the END key
14. Press # MENU MENU quickly
15. Enter OTKSL
16. The work MIN will be highlighted
17. Select the word CHANGE by selecting the top right button
18. Select DELETE. Press and hold the button until clear
19. Have the customer enter the 10 digit MIN number
20. Select OK with the top right button. The “User Activation” screen will appear
21. Scroll to highlight the CDMA Sys ID
22. Select CHANGE by selecting the top right button
23. Enter SID
24. Select OK by selecting the top right button
25. Select DONE with the top left button
Press the END key
Motorola Phones (ALL)

1. Enter 74663 # FCN FCN
2. Enter OTKSL
3. Enter MIN and press STO
4. Enter SID (4654) and press STO
5. Press STO again – programming is complete
Note: on the Tarpon (120C) you will need to press the MENU key instead of FCN.

Nokia:
5185/6185 programming: *3001#12345#
Software version: *#837# or *#VER# or *#9999#
Serial / ESN: *#92772689# or *#WARRANTY#
Phone reset: *#75681# or *#75682#
Nokia 6185-5170

1. Press *#639#
2. Enter OTKSL and press OK
3. Enter the MIN and select OK
4. Enter the SID and select OK
5. Programming is complete
Nokia 3585

1. Enter ## followed by the OTKSL
2. Number (MDN) is highlighted. Press the upper left-hand soft key to select
3. Mobile Number will display. Enter the 10 digit MIN
4. Press OK
5. IMSI will appear. Press and hold the Clear key until the display is empty.
6. Enter 31000 plus the MSID (15 digits total)
7. Press the upper left hand soft key and select OK
8. It will take you back to the SVC Programming. Press the upper right hand soft key to select EXIT
9. Press END.
10. Phone will power cycle and programming is complete.

SK Teletech:
SK-IM 1000/1400/2000/2200/2400 programming: #7583538324#626#

Getrun 2000:
System NAM programming mode: 0 + 1 + # + 7 + 3 + 7 + SECURITY CODE (000000)
Debug menu: 0 + 1 + # + 3 + 2 + 4 + SECURITY CODE (000000)
Debug screen of field test mode: 0 + 1 + # + 7 + 2 + 7
Test mode: 0 + 1 + # + 7 + 6 + 4 + SECURITY CODE (000000)
System test mode: 0 + 1 + # + 7 + 6 + 8 + SECURITY CODE (000000)

NEOPOINT:
Neopoint 1000
1. Press M to display Main Menu
2. Scroll to PREFERENCES
3. Press softkey under SELECT
4. Enter 040793
5. Scroll to PROGRAMMING
6. Press softkey under SELECT
7. Enter OTKSL
8. Press softkey under DONE
9. Scroll to PHONE NUMBER
10. Enter 10 digit MIN
11. Scroll to HOME SID
12. Enter SID (4654)
13. Press softkey under SAVE to exit
14. Programming is complete
NEOPOINT 1600
1. Power the phone on
2. Press the "Menu" key
3. Scroll to "Preferences" - press "Select"
4. Key in the "Field Service Code" (the phone will not prompt you for the code)
at the "preferences" screen to access the "Service" menu (Default code is "000000")
5. Scroll to "Programming" - press "Select" - the phone will ask for the "Subsidy Lock Code"
6. Enter the "Subsidy Lock Code(654321)" to access the "NAM" menu
7. Select the NAM to be programmed (NAM 1 or NAM 2)
8. Program the NAM - Phone number and CDMA Home SID
9. After programming has been completed press "Save" - the phone will reset

Audiovox:
Audiovox 9100
1. Press ##
2. Enter the OTKSL
3. Display will read Service/Menu 1 Basic…press OK
4. Next screen will read Service Mode/Home SID…press OK
5. Next screen will read Service Mode/Home SID…press OK
6. Device will display Service Menu 1. Basic #
7. Press END button to complete programming

Handspring TREO:
1. Open the flip and press the PHONEBOOK button one time to display the dial pad
2. Enter ## and the OTKSL using the numbers on the Dial Pad
3. Press the handset button shown in the diagram above
4. At the Activations screen enter the MIN in the phone number field using the numbers on the device keyboard
5. Put a check in the Enable Number Portability box and type the MSID in the MSIN field
6. Press OK
7. The device will display the network search pop-up and return to the Phonebook display

Hitachi P300:
1. Enter ## and the 6 digit OTKSL
2. Press the Options soft key and then scroll to Save Phone #. Press the OK soft key.
3. At the NAM display scroll to EDIT and press the OK soft key
4. Display will read NAM and MDN will be highlighted. Press the OK soft key.
5. At the MDN display enter the 10 digit MIN and press the SAVE soft key.
6. At the Save prompt press the OK soft key. The next display will show several options that should not edited.
7. Press the EXIT soft key and the device will power cycle.
8. Programming is complete.

Kyosera:
Kyocera 2345 1135

1. Press 111111 (#1 key 6 times)
2. Option will be highlighted
3. Press OK
4. Scroll down to Programming
5. The service programming dialog will appear Enter Security Code.
6. Enter the 6 digit OTSKL (code will show as asterisks on screen)
7. Service Options will appear
8. Scroll down to the BASIC NAM1 Info
9. Press OK
10. Select the Phone Number by pressing the OK key
11. Using the keypad enter the 10 digit MIN
12. Press OK
13. Press END to complete the programming
Kyocera 6035

1. Press 1 six times (111111) and select OPTIONS
2. Select PROGRAMMING
3. Open flip
4. Tap the OTKSL on keypad on the screen. Tap OK
5. Tap on the PHONE NUMBER field. Enter MIN.
6. Leave A-KEY blank
7. Enter HOME SID (4654)
8. Tap SAVE & EXIT
9. Tap YES
10. Phone will be in OFF MODE Close flip.
Kyocera 3035
1. Press 111111 (the #1 key six times)
2. Options will be highlighted
3. Press in the navigation key (Navigation key is the button located between the TALK & END key)
4. Scroll to PROGRAMMING using the Navigation key
5. Select PROGRAMMING by pressing in the Navigation key
6. Enter the six digit OTKSL and press in the navigation key
7. SERVICE OPTIONS will appear
8. Scroll down to the Basic NAM1 info
9. Press in the navigation key
10. Clear any numbers that may appear using the “clear” key (arrow key located directly below the navigation key)
11. Select the PHONE NUMBER by pressing in the navigation key
12. Enter the 10 digit MIN select OK by pressing in the navigation key
13. Press END. Programming is complete.
Kyocera 2255
1. Press the 1 key six times (111111) “Option will be highlighted
2. Press OK
3. Scroll down to “Programming” and press “OK”
4. Enter OTKSL and press the navigation key
5. “Service Options” will appear scroll down to the “Basic NAM1 Info”
6. Press OK
7. Select Phone Number by pressing OK
8. Enter MIN and press OK again
9. Scroll to Home SID and press OK
10. Enter SID (4654) and press OK
11. Press END. Programming is complete.
QCP 2035
1. Press 1 six times (111111)
2. Press u key to select OPTIONS
3. Highlight PROGRAMMING and press u key
4. Enter OTKSL
5. ESN will appear press left arrow key to select OK
6. Enter MIN and press ç key
7. Press ç key again to exit - Programming is complete

Sanyo:
Sanyo 4000 4500 4700 5000 6000
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. ESN will be displayed – press OK
5. Enter 10 digit MIN and press OK
6. Enter SID (4654) and press OK
7. Press OK twice
8. Programming is complete
Sanyo 5150 5300 and 6400
1. Enter ## followed by the OTKSL
2. Press MENU SAVE PHONE #
3. Press Ok
4. SVC Programming will be displayed. Scroll and highlight Mobile Number. Press OK
5. Press OK again
6. ESN will be displayed. Press OK
7. Mobile Number will be displayed enter the 10 digit MIN press OK
8. Press OK 4 times
9. Phone will power cycle
10. Programming is complete
Sanyo 6000
1. Press ##
2. Enter OTKSL
3. Press MENU Key and scroll to SAVE PHONE # and press OK
4. ESN will be displayed press OK
5. Enter MIN and press OK
6. Enter SID and press OK
7. Press OK twice more
8. Programming is complete
Sanyo 4900
1. Enter ## followed by the 6 digit OTKSL
2. Press the MENU/OK key and scroll and highlight SAVE PHONE #
3. Press MENU/OK
4. Scroll and highlight MOBILE NUMBER press OK
5. At the ESN display press OK
6. In the MOBILE NUMBER screen enter your MIN and press OK 4 times
7. At the service program menu scroll to exit and press the MENU/OK key.
8. Programming is complete
Sanyo 6200

1. Enter ##
2. Enter OTKSL
3. Press the MENU key and scroll to highlight SAVE PHONE #
4. Press OK
5. Scroll and highlight MOBILE NUMBER
6. Press OK twice
7. Scroll and highlight EXIT
8. Press OK
9. Phone will power cycle
10. Programming is complete

Toshiba:
Toshiba 2032P
1. Slide the Radio Standby Switch on the left side of the device to the upper side (ON) to activate the phone function. This is the switch with the phone icon over it
2. After power up is completed use the stylus to tap on the ADMIN pull up menu at the bottom of the screen and select ACTIVATION WIZARD. If your device has not yet been activated the ACTIVATION WIZARD will automatically start when you turn on the radio in your device.
3. Tap NEXT 3 times. If the device has been previously activated it will require only 2 presses.
4. On the fourth screen enter the 6 digit OTKSL using keyboard
5. Enter the MIN in both entery fields then tap NEXT
6. Wait for the device to initialize and display “ready to connect”
7. To initiate IOTA tap the word ADMIN at the bottom of the display and then Data Provisioning
8. Programming is complete
*******
· Here is a list of various codes to try out. Some may require an MSL to be able to make full use of the functionality.
##2769737 [##BROWSER] - MiniBrowser Settings (2G)
##8626337 [##VOCODER] - Set Vocoder
##3282 [##DATA] - Setup Menu for Vision handsets
##8463 [##TIME] - Airtime Menu
##040793 - Debug Menu
##786 [##RUN] - Technical Information (be careful with this one, you can reset the handset)
##932 [##WEB] - IP Address information (2G)
##889 [##TTY] - TTY On or TTY Off
##4357 [##HELP] - Help

SK TELETECH Phone Codes

2010-12-19T20:03:00.001-08:00

[SK TELETECH]

--------------------------------------------------------------------------------

Sky All Models Nam Programming:

Nam Set: #7583538324#626#

Nam Set: *759#364*7388464#

Min simple mode: #758353266#646#

Irm simple mode #758353266#476#

Voice memo: #8767#277#

Test Mode: #7583538324#8378#

A-key: #758353266#2539#

Service Menu: Menu+4+0+Spc

Service Menu: Menu+5+0+Spc

Panasonic Phone Codes

2010-12-19T20:02:00.001-08:00

[PANASONIC]

--------------------------------------------------------------------------------

PANASONIC TEST MODE:

Panasonic (Most):

1) Turn on the phone. Press #7764726# choose SEND

2) Scroll down to where it says "NAM 1" and choose OK. Scroll down

to "Access To Level 4" choose YES. Scroll down to "Built-In-Monitor"

and choose EDIT.

3) Press 1 and choose OK then choose BACK. The phone will say

"Back To Level 1" choose YES. Now choose EXIT the phone will ask you

"Exit And Save Change" choose YES.

4) Signal strength is the top right number on the screen.

5) To turn off the test mode follow the above sequence except press 0

instead of 1 at the "Built-In-Monitor"

NEC Phone Code

2010-12-19T20:01:00.001-08:00

*#CODE#
CODES :
06 IMEI
7468658 SIM INFO
746255 SIM INFO
7464674 IMSI
2820 SW WERSION
79837 SW + DSP WERSION
49837 ****************
79786 Checksum
28453 Build Levev
737425 SERIAL NUMBER !!!!
73738 -
737247 Reapir History
7463424 SIMM Diagnostics
284538 Build Date
84769 Power ON
497837 Hysteresis
3643278746 Enhanced speed
3648658746 3 Volt Sim
347722 Clear Cause
627538 Market
7320 Network Lock
4960 USIM Card Lock
3210 SP Lock
8140 Coorporate Lock
5830 Unlocking Code !!!
6210 MSISDN - Current Phone Number

*#7320# and see what it says
and
*#3210# and see what it says
br

SP Lock (*#3210#)
Corporate or Net Lock (*#8140#)
Network Lock (*#7320#)
#4960*4960# full unl

Special codes supported by the e616 include:
*#06# shows IMEI number
*#2820# shows Software Version
*#3210# shows SP lock info
*#4960# shows sim lock info
*#7320# shows net lock info
*#8140# shows corporate lock info
*73738# master reset
#7320*(8 digits password)# release the Net Lock, password required.

The codes are entered in the same way as a normal phone number.

If you have more info please send me at mks@nm.