Printer Repair And Service Tools

Error Ink Pads Epson L200

noreply@blogger.com (Resetter Printer) — Sat, 5 Oct 2013 11:53:00 +0700

Epson L200 is an All-In-One printer, All-In-One printer is a printer unit has multiple function as Scanning, Photocopying, and printing.

Epson L200 comes with 6 ink bottle consist of 3 Black Ink, and colored ink, 1 bottle for Cyan, 1 bottle for Magenta, and 1 bottle for Yellow Colors. This set of inks can yield approximately 18,000 pages for black and 6,500 pages of colored print.

Epson L200 adopt the technology of using an ink tank or before a converted printer done by the third party.

Epson L200 comes with many advantage and on the other hand, also we expect some worst problem arising from it. The common problem with this printer are the following; no power, printing problem, ink pumping, and blotted image.

Such a problem can not print then out error " The printer 's ink pads are at the end of their service life ." When we take it to the place of service usually they reasoned that it should be replaced . Actually quite reset printer epson l200 with software Adjustment Program for Epson L200 .His manner is very simple reset

Run the Adjustment Program for Epson L200 , choose Particular adjustment mode .

Run the Adjustment Program for Epson L200 , choose Particular adjustment mode .
In the next window select the Maintenance menu Waste ink pad counter then click OK
At Waste ink pad counter window , click the Check button , you will see the value of each point on the counter . In the picture below looks Pad Counter Main section has passed through a maximum value . To reset select each counter , then click the button Initialization
It would appear the message pop - up " When the OK button is clicked , the initialization is done" click OK
Turn the printer off , then turn it on again and wait a few moments .
To check whether the counter value has been successfully reset , press the Check button , Main pad counter value should be changed to 0 % . Click Finish to exit .

Epson L200 printer has been successfully reset, then do a test print to ensure good printer

https://www.mediafire.com/file/eds9b7daksc1hmt/Reseter_Epson_L200.rar/file
Link Download File:

Download Adjustment Program for Epson L200

head cleaning epson R230x

noreply@blogger.com (Resetter Printer) — Sat, 24 Aug 2013 19:39:00 +0700

1. Turn on the Epson Stylus Photo R230 printer or yours R230x
2. Click Start> Control Panel> select Printers and Faxes> Epson R230
3. Click Select Printer Printing Task prefference on the box that is on the right side of the window or can
also right-click on the Epson R230 and select Printing Prefferences
4. Select the Maintenance tab dialog box appears so that these

5.Then select Head Cleaning as shown in the picture above that I put a red circle, it will
display a dialog box like this

Select the start like in the picture above that I marked in red arrows, then this machine will do the print head cleaning, ink pumping Please wait for the printer to finish.

Epson R230x paper jam problem repair

noreply@blogger.com (Resetter Printer) — Sat, 24 Aug 2013 19:06:00 +0700

R230X, R230,R220 epson printer suddenly could not pulling the paper so the paper can not get in to do the printing and sometimes even encouraged, but paper still can not get even get damaged paper
Epson R230 printer has 2 paper roll that serves interesting, this roll is located at the top and bottom of the printer, the printer In this type often have constraints that can not pull the paper at the time of print, the problem is usually caused by not working epektifnya rubber roll the many things that cause the rubber does not work well.which are:

1. Rubber is not abrasive (slippery)
2. A lot of dirt that sticks to the surface of the rubber
3. Rubber surface is bare

To overcome the above problems are many things we can do, from start fixing up the new one to replace it
To fix this follow the following steps:

1. Open the printer lid up to the opening roll.
2. Two roll rubber washer uses ordinary water course until clean.
3. Dry the rubber roll that has been in the washing to dry
4. Add seltipe the rubber where the rubber needs to be fixed purpose meeting and rather thick
5. Plug it back into its original position
6. completed

Hopefully the above tips can solve a problem with your printer, if there are any questions please leave a comment on this post.

Canon GENERIC "S" SERIES RESET CODE

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 17:56:00 +0700

Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout. javascript:void(0)
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

resetter epson r230x (SSC Service Utilily)

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 12:37:00 +0700

1. Make sure the printer is turned on and terkonek with a computer (printer driver already installed)
2. Install SSC Service Utility and run the program
3. Model of printer configuration settings. Select the Epson Stylus Photo R230. After the play closed
windows.

4. In the lower right corner of the taskbar (near the clock) right click the icon SSC Service Utility, select
" Protection Counter" click "Reset protection counter" select Yes on the pop up that asks
"Have you Replace waste ink pad"

5. Restart the printer, the printer is ok

That's the steps I described to my friend, so she does not go back and forth to the printer lift handyman service to reset Epson R230. May be useful.

Link Download File:

Download SSC Service Utility

Canon Pixma IP2770 Error 006

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 12:10:00 +0700

To resolve Error 006 on Canon iP2770
1. Canon iP2770 Driver uninstall then restart
2. then install again
3. do reset the service tools program
4. print as usual
5. completed

Canon Pixma IP2770 Error 5100

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 12:06:00 +0700

Error 5100 occurred at Canon iP2770 Printer This is usually caused because they are not detected by the Printer Cartridge. So the message Error 5100 We inform that the printer can not find its cartridges. Steps that must be done
1. Turn off the printer
2. Remove both cartridges from the printer
3. Use a cloth moistened with alcohol to clean the surface of the contact / terminal connector that touches
Cartridge printer / could also use a pencil eraser
4. Replace the two Cartridge
5. Turn on the printer.

Printer Canon IP2770 Error 5200

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 12:05:00 +0700

When iP2770 is turned on, the printer looks normal with LED Flash GREEN. But after ordered to do pengeprinan, the error 5200 would show up, and the LED will turn green ngeblink orange 1x to 8x
For error 5200 Printer Canon IP 2770/2700 is the same as I fix Error 5B00 above but for this error problem you just need the first step Error 5B00 following:

1. Make sure that the printer Canon IP 2770 / IP 2700 is turned off (Off) But the power cable

(power) installed.
2. Press the RESUME button for about 2 seconds
3. After that you press the POWER button until the green light on (when pressing the POWER button,
Resume button not released yet)
4. Then release the RESUME button, but do not release the POWER button.
5. POWER button while still depressed, press the Resume button 5 times. Led will light turns green to
orange last flame orange. (not to be mistaken 4x because the printer will die in total, but also temporary)
while reading the writing on the nature of the above.
6. Release both buttons simultaneously.
7. LED will blink briefly then will flash GREEN.
8. The computer will detect the new device, just ignore it
9. Press the Power button so that the printer OFF / Off
10. Once the printer is completely dead then press the Power Button Back then the computer will turn on
and be ready for use again.

Service tool pixma ip2770 (Resetter Pixma iP2270)

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 12:00:00 +0700

steps reset canon pixma iP22700:
- Log on to the service mode first connect the printer to the computer and the power cord without turning
on the printer (the printer is turned off).
- Press the Resume button about 2 seconds and then press the POWER button until the green light on
   (when pressing the POWER button, Resume button jgn removed)
- Then off the RESUME button, but do not release the button POWER
- While the POWER button still depressed, press the Resume button 5 times. Led will light turns green to
   orange last flame orange. (not to be mistaken 4x because the printer will die in total which means that the
   steps we have to reinstall from scratch)
- Then release both buttons simultaneously, the LED will blink briefly then will flash GREEN.
- At this time the computer will detect a new device, just ignore it and wait until the process is complete.
- This situation shows the iP2770 printer is in a state of SERVICE MODE and ready to reset

for permanent service

1. Download Resetter
2. Exctract File Resetter iP2770.
2. Service Tool ServiceTool_V1050

3. Click the "MAIN", then the printer will proceed, then iP2770 will print one page
with the words "D = 000.0
4. Click "EEPROM Clear".
5. Then click "EEPROM", and the printer will print the results iP2770 Resetter. One line in his writings as
follows: "TPage (TTL = 00000)"
5. Turn off the printer by pressing the POWER button.
6. Up here if all goes well, it's too printer will reset and is back Normal.

the following ink may have run out calour canon MP250, IP 2270, MP160, iP2700

noreply@blogger.com (Resetter Printer) — Thu, 22 Aug 2013 11:29:00 +0700

When the printer is turned on seems OK, but after the print command, it will display Blink 13x Orange on the Canon MP250, MP160, iP2770, iP2700

the following ink may have run out Color

Blink 13x Orange lights with the picture above, means catrid color reset press the Resume button requires a bit longer until the GREEN light flashes, then release. black catridge also need to be reset and the picture is as follows:

the following ink may have run out Black

Same way: rather long press the Resume button until the GREEN light flashes, then release.after doing these steps then the printer will return to normal. This often occurs when the cartridge runs out complete refill then installed again.

Canon MP145 waste ink counter

noreply@blogger.com (Resetter Printer) — Wed, 22 Jul 2009 16:58:00 +0700

The method used to is by reset the printer

Error ink cartridges are not installed properly (error E5) :
Step 1 : Push Power switch by continue (Push Power On/Off)
Step 2 : inserrt plug(Hold and Press Power)
step 3 : Push Reset button 1x, Let Power button, Push Reset twice till 0
Step 4 : Push + display change from 0 to 1 (push button + to change 0 to 1)
Step 5 : Push Power switch again , Printer will be print 1 page
(push power button–>start button till 1 page.)
step 6 : Open cover
Step 7 : Unplug power cable
Step 8 : Take out ink PG 40 and PG 41
Step 9 : Insert plug again
Step 10 : Push power switch
Step 11 : Open cover (scan cover)
Step 12 : Inksert ink PG 40 , PG 41 again

These are the step How to Reset waste ink counter (error E16) :
1. Turn off power button (power button is in ),
Press and Hold STOP/RESET then Push ON/OFF button
2. Hold ON/OFF button, press STOP/RESET button 2x
3. Let both of button and printer in to SERVICE MODE
4. Printer will be charging
5. After printer finish charging, ush STOP/RESET button 4x. (Waste ink counter reset)
6. Every time you push STOP/RESET button ,
ON/OFF lamp will change green and oranye.
7. Turn off printer dan and take out POWER button
8. Turn on printer again.

The number of the Reset :
button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)

Error Code/Kode Error :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 – Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error – USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

Download Link : Canon Resetter
Download Driver : Canon MP145

Canon i80 Waste Ink Tank Full

noreply@blogger.com (Resetter Printer) — Mon, 20 Jul 2009 12:08:00 +0700

Try this to reset the error.

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6) Power off then back on and test.

Canon Multi-Pass Fax C855 waste tank reset code

noreply@blogger.com (Resetter Printer) — Mon, 20 Jul 2009 12:01:00 +0700

Resetting the Waste Ink Volume Counter

1) Enter SERVICE MODE.....By pressing THEN #.
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT]. Let the printer complete its reset cycle (about 20 seconds).
6) Turn the printer off and on by unplugging the power cord and plugging it back in.

Canon Multipass F30, F60 & F80 waste tank reset code

noreply@blogger.com (Resetter Printer) — Mon, 20 Jul 2009 11:56:00 +0700

Resetting the Waste Ink Volume Counter

1) Enter SERVICE MODE.....By pressing Menu THEN Copy THEN #.
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key. (On F30 printers, skip step (6) since there is no [OK] key .)
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

SERVICE MANUAL CANON iR1022

noreply@blogger.com (Resetter Printer) — Sat, 18 Jul 2009 23:04:00 +0700

High quality 22ppm black and white printing. Compact design for day to day office use. Easily Network Connected.

Manual Service : Download
Driver iR1022/1018 : Download

canon waste tank reset for canon i70

noreply@blogger.com (Resetter Printer) — Sat, 18 Jul 2009 22:14:00 +0700

Below is a procedure that in most cases should resolve a Canon i70 waste tank issue

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button.

(Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button.

(Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button 3 times, and then release the Power and Resume/Cancel buttons.

(Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button 4 times (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

After the function (menu) is selected, press the Power button. The LED lights in green, and the selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

*** 4 times Green Waste ink counter resetting Both the main and borderless print waste ink counters are cleared.

Canon i70 InkJet Photo Printer
Manual service : Download
Driver Canon i70 : Download

MP390 Waste ink tank full

noreply@blogger.com (Resetter Printer) — Sat, 18 Jul 2009 21:56:00 +0700

1. Printer ‘on.’
2. Press: “Additional Functions” button
Press “Scan” button
Press “Copy” button
Press “Scan” button
3. Now it says, “Service Mode / #1 SSSW.
4. Keep hitting “+” [which is the right arrow]; it will go through #1 to #11 (Date/Time), then “Service Report,” and, lastly, “Test Mode.” Then hit “Set.”
5. Now you will have another set of selections. Keep hitting “+” [the right arrow] to go from #1(DRAM) to #8 (Printer Test). Then hit “Set.”
6. When it finishes some sort of function, “Please Wait” will be replaced by “-8-2+” Then hit “+” and it should then say “-8-3+” and you hit “Set.”
7. The screen should now say “EEPROM Clear.” [You may need to press “Set” then, to get to the next step? My notes aren’t clear.]
8. Option 0 should be “select ink count.” Press “Set.”
9. Press the “Stop/Reset” button.
10. Press the “On/Off” button.
11. Wait for the printer to restart.

I have had the “waste ink tank near full” message twice in the almost-3-years I’ve been using my printer and it’s still functioning fine. No “waste ink” coming out the bottom!

Refill Instructions HP Cartridge C9352 #22

noreply@blogger.com (Resetter Printer) — Sun, 5 Jul 2009 11:36:00 +0700

1. Put the cartridge on some paper towels in an area where you can tolerate a spill.

2. Peal off the top label.

3. Fill the syringe with 5 ml. of color ink.

4. Very S-L-O-W-L-Y inject ink into each chamber until the sponge is full. A little ink might come out of the top when full, so cover up the other two holes while filling one.

5. When finished, replace the top label or leave it off (it will make no difference in the printing).

6. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.
Or print Test pages.

Canon PIXMA MP476 All-in-one Inkjet Printer

noreply@blogger.com (Resetter Printer) — Wed, 24 Jun 2009 12:23:00 +0700

Design of the Canon PIXMA MP476 All-in-one Inkjet Printer

The Canon PIXMA MP476 uses the same basic design as the PIXMA MP510. The black-and-silver body measures 451 x 353 x 169mm. The silver scanner lid conceals an A4-size flatbed scanner. Because the MP476 lacks an automatic document feeder, you can't scan legal-size documents.
The paper handling system is simple. A paper input support flips open in the rear and the front panel of the printer folds open to serve as the output tray. Next to the output tray is a small door that conceals two memory card slots. The slots accept most common types of memory cards, though some require an adapter (which is not included).

Hidden away under the memory cards is a PictBridge-enabled USB port (it's so hidden that we missed it on first inspection). You can use it to connect PictBridge cameras for direct printing, or to attach an optional Bluetooth adapter (sold separately) for wireless printing. The one thing you can't attach to the USB port is a flash thumbdrive; the Dell Photo 926 lets you print files from an attached flash drive.

The control panel is hidden underneath a flip-up panel on the top side of the printer. Embedded on the underside of the panel is a 1.8-inch graphical LCD. The control panel is basic, though well-organized. Buttons include task buttons for copy, scan, and memory card modes, menu navigation buttons, and two start buttons--one for black-only and one for color.

The PIXMA MP476 uses a two-tank ink system: One black and one tri-color. It ships with regular capacity cartridges, but you can replace both with high-capacity versions.

Reset Blinking Printer Canon IP100

noreply@blogger.com (Resetter Printer) — Wed, 24 Jun 2009 09:37:00 +0700

The methods
Step1: Manual for Service mode
1. Take of POWER cable and USB.
2. Open printer cover and Push + Hold power button
3. Put on POWER Cable
4. Close printer cover, let power button.
5. Turn on printer as usual & it should be not blinking more

Step 2 : Make it permanent
1. Connect USB cable & turn on Printer
2. Open “General Tools for iP1000″,
download click here
3. choose your USB PORT
4. Choose SET DESTINATION – 1

It should be work if u do the steps above.
Try it and Good Luck.

I'll wait ur comments.

Canon Pixma MP110

noreply@blogger.com (Resetter Printer) — Sun, 26 Apr 2009 09:44:00 +0700

How To Reset Waste Ink Canon Pixma MP110

Here this step by step to resetting waste ink counter printer Canon Pixma MP110
1. You will include printer.
2. press button Menu, then Scan, Copy and again Scan. All - entered into the service
regime. 3. Select Counter.
3. Press button Copy - all Pampers is discarded into zero.
4. You will turn off printer by button POWER.

Reset tool permanent for canon Pixma Mp110 Download
Manual reset canon
How_To_Reset_Waste_Ink_Canon_i320_and_i255
How_to_reset_waste_ink_canon_iP4000
How_To_Reset_Waste_Ink_Canon_Pixma_MP110
How_To_Reset_Waste_Ink_Canon_Pixma_MP130
How_To_Reset_Waste_Ink_Canon_Pixma_MPC190
How_To_Reset_Waste_Ink_Printer_Canon_BJC_2000_and_BJC_2100

reset waste ink canon iP4000

noreply@blogger.com (Resetter Printer) — Sun, 26 Apr 2009 09:28:00 +0700

Here this step by step to resetting waste ink counter printer canon iP4000
1. With the printer plugged in and powered off, press and hold the
Resume/Cancel button, then press and hold the Power button.
Do not release the buttons. The LED light should be green to
indicate that a function is selectable
2. While holding the Power button, release the Resume/Cancel button,
do not release the Power button
3. While holding the Power button, press the Resume/Cancel button 2 times,
and then release both the Power and Resume/Cancel buttons. Each time the
Resume/Cancel button is pressed, the LED lights alternately in orange and
green, starting with orange.
4. When the LED light is green, press the Resume/Cancel button 4 times. Each
time the Resume/Cancel button is pressed, the LED lights alternately in
orange and green, starting with orange.
5. Press the Power button. The LED lights in green, and the reset is performed.
When the operation completes, the printer returns to the menu selection
mode automatically
6. Press the power button to exit service mode.

RESET WASTE INK TANK CANON

noreply@blogger.com (Resetter Printer) — Tue, 7 Apr 2009 18:24:00 +0700

For seri i250, i255, i350, i355, PIXUS 350i

indicates :
WASTE INK TANK Full, printer has no respon

The Solutions :

1. Download i320 Service Tool or 350,355,250,255 Service Tool
2. Do service mode procedure to printer, the methods are ::
- Turn off printer, Take off USB cabel dan power cabel
- Push and hold POWER button, take on power, Turn on printer
- Indikator LED will be in green colour
- Push and let RESUME button, indicator LED will be in yellow colour
- Push and let RESUME button once more, indicator LED will be in green colour
- Let POWER button

This time printer in MODE SERVICE

Reset Manual i255-i355.pdf
ManualReset_i320.pdf

3. Do reset waste ink tank procedure with :
4. take on USB cabel
5. Do program General Tool
6. The Figure will be like this :
7. Choose the parameter no 1
8. Put on no 2 according to printer canon, DON”T BE WRONG!!!
9.Congratulation… printer has been in Reset.

Reset MP390 Waste Ink Full Tank

noreply@blogger.com (Resetter Printer) — Fri, 3 Apr 2009 20:41:00 +0700

The below reset procedure worked for me. I did not have to clean the waste-ink sponge. Many thanks to lp who originally posted it and to "Anonymous" who reposted it.

1)Printer on, press Additional Functions, Scan, Copy, Scan
Now you should be in service mode from there for waste ink tank reset

2)Select Test mode which is like the last avalabe selection
3)Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

The menu will now say EEPRON Clear
Select Ink count which is option (0) and press set

Then press Stop/Reset Followed by the power button and then wait for it to restart.

iP Tool : Download
EEPROM Printer Canon ip6210D/6220D/MP170/MP450/2200/ip600 Download
MPTool MP150/MP160/MP170/MP180/MP450/MP460 Download
Step By Step Resetter canon MP Download

Reseter Printer Canon IP1880

noreply@blogger.com (Resetter Printer) — Fri, 3 Apr 2009 20:11:00 +0700

To reset manually Ink Full Tank, try these methods :
1. Turn on Printer Canon iP 1880
2. Push and Hold resume button about 2 minutes
3. Release resume button
4. Printer will back in normal again
5. Then use the software.
6. Good Luck friend
7. If you want this permanent, Please Download Reset Tool

8. Reset tool support Canon iP2500, iP 1800, iP 1100

Download step by step canon iR1880, iP1980
Don’t forget your comment in guest book.