Printer Self Repair

Adjustment by using adjustment program Epson Stylus Photo R200 R210

Tue, 10 Apr 2012 16:11:51 GMT

The procedures of the adjustment items will be explained here. The intended item is as The procedures of the adjustment items will be explained here. The intended item is as Offset Input for CR Motor Calorific Limitation A4 Photo Paper Glossy Photo Paper Print

EEPROM Data Copy Epson Stylus CX4100 CX4200 CX4700 CX4800 DX 4200 DX4800 DX4850

Sat, 10 Mar 2012 06:29:46 GMT

1. Select EEPROM Data Copy in the Adjustment Program. 2. Click the backup button to backup the old main board data. 3. When the backup operation is succeeded, 1 Replace the Main Board Unit with a new one. 2 Turn on the printer and click the restore button. 3 When the restore operation is succeeded, click the next button to perform necessary adjustment. When the backup operation is failed, 1 Click the next button to perform necessary adjustment.

Paper Support AssyHousing leftrightStacker Assy removal Epson Stylus Photo R200 R210

Fri, 10 Feb 2012 03:30:58 GMT

C. B.P 3x8 4-6kgf cm I C.B.P 3x8 4-6kgf cm C. B.P 3x8 4-6kgf cm I C.B.P 3x8 4-6kgf cm Figure 2-2. paper support assy. Housing left right Stacker assy. removal Figure 2-2. paper support assy. Housing left right Stacker assy. removal Parts Units which should be removed before removing paper support assy. Housing left right Stacker assy. Paper support assy. removal 1. Release two protrusions for securing the paper support assy. to ASF frame. Housing left right removal 1. Remove the screw E , x1, Z...

EJ Frame AssyEJ Roller Epson Stylus CX4300 CX4400 CX5500 CX5600 DX4400 DX4450

Wed, 08 Feb 2012 10:05:46 GMT

Part Unit that should be removed before removing EJ Frame Assy EJ Roller Document Cover ASF Cover Support Arm Scanner Unit Middle Case Panel Unit Printer Mechanism When installing Spur Gear, 59. 6 and the EJ Roller, be sure to install new ones. These parts cannot be reused. 1. Remove the Grounding Spring from the EJ Frame Assy. 2. Remove the screws x2 and remove the EJ Frame Assy. Figure 4-63. Removing EJ Frame Assy. Figure 4-63. Removing EJ Frame Assy. 3. Insert a flathead screwdriver between...

Work Completion Check Epson Stylus CX4300 CX4400 CX5500 CX5600 DX4400 DX4450

Fri, 03 Feb 2012 09:00:21 GMT

If any service is made to the printer, use the checklist shown below to confirm all works are completed properly and the printer is ready to be returned to the user. Is ink discharged normally from all the nozzles Is there any abnormal noise during its operation Is the CR Motor at the correct temperature Not too hot to touch No paper jamming No paper skew No multiple feeding No abnormal noise Is the PF Motor at correct temperature Is the paper path free of any obstructions Does it move together...

Ribbon Advance Mechanism Epson LQ 2170

Wed, 12 Oct 2011 01:23:56 GMT

The ribbon is held between the ribbon advance roller ribbon driven gear and the ribbon pressure roller. When the carriage moves from left to right and vice versa on the CR guide shaft, the timing belt turns the belt-driven pulley. Then the torque is transmitted to the ribbon driving gear through the gear trains. The ribbon driving gear rotates counterclockwise, no matter what direction the carriage moves, because a planetary gear is used in the gear linkage. Table 2-4. Ribbon Advance Gear...

Removing the Print Head Unit Epson Stylus Color 440 640 740

Tue, 27 Sep 2011 00:50:45 GMT

1. Remove the housing. Refer to Section 4.2.1. 2. Rotate the flat gear 67.2 towards yourself front and release the carriage lock mechanism. Then move the carriage to the left edge. 3. Take both black and color ink cartridges out of the printhead unit. 4. Remove the blue covers for black and color ink cartridges from the carriage assembly. 5. Remove the torsion spring 49 and one screw No.3 and take the fastener head out. 6. Remove the FFC being placed on the carriage assembly, and remove the...

Info Crs Epson Stylus Photo R260 R265 R270 R360 R380 R390

Tue, 27 Sep 2011 00:13:41 GMT

For sheets of paper, set the front tray to the paper position by pulling up the tray lever. For a CD or DVD, set the front tray to the CD DVD position by pushing down the tray lever. The CDR guide status does not match with the print setting. The front tray is not in the CD DVD position. Push down the tray lever to raise the front tray to the CD DVD position. For sheets of paper, turn off the printer and then remove any jammed paper by hand. For a CD or DVD, remove the CD DVD tray. Next, press...

I Clq Epson Stylus Photo 890 1280 1290

Mon, 26 Sep 2011 21:21:10 GMT

When removing HOUSING, PANEL, LEFT, watch out for the Stacker Assembly. Since the Stacker Assembly is fixed by the Panel Unit and HOUSING, PANEL, LEFT, it will come off as HOUSING, PANEL, LEFT is removed. 6. Remove 2 screws CBS, 3x6 securing HOUSING, SUB, LEFT to the printer mechanism. 7. Release 3 hooks 2 at the bottom and 1 in the front fixing HOUSING, SUB, LEFT to the printer mechanism, and remove HOUSING, SUB, LEFT. 8. Remove 1 or 2 screws CBP, 3x6 Stylus Photo 890 1 screw, Stylus Photo...

Board Removal Epson Stylus C82

Mon, 26 Sep 2011 20:28:56 GMT

1. Remove Printer Mechanism. See Section 4.2.1.4 2. Remove all cables from C486 Main Board and peel off acetate tape in 2 places. 3. Remove 4 screws C.B.S 3x6 1, C.B.S 3x8 2, C.B.S 3x16 1 holding C486 Main Board, then remove Printer Mechanism from C486 Main Board in upward direction. The CN19 cable on the C486 Main Board has a specified installation direction. The pin connected to the blue line of the cable should be inserted into the Pin 1 side of the connector. Figure 4-16. CN19 Connection...

Print Paper Thickness Detection Pattern Epson Stylus Pro 7600 9600

Mon, 26 Sep 2011 19:09:36 GMT

Upper patterns Leftward Lower patterns Rightward Lower patterns Centered on base position for gap adjustment value, and displaced by an equal distance left and right. Details are described in next clause. Relationship between numbers in print pattern and paper thickness.

I Iwp Epson Stylus C63 C64 C83 C84

Mon, 26 Sep 2011 14:19:24 GMT

Do not touch the rib of Paper guide front and Porous Pad, Paper guide, Front . Do not touch eight feet of Porous Pad, Paper guide, Front Sub . When assembling Paper guide front to main frame, Do not touch the rib of Paper guide front and Porous Pad, Paper guide, Front . Make sure to install the dowels of Paper guide front into the holes of main frame. Make sure that there is no gap between Paper guide front and main frame. Be careful not to bend eight feet of Porous Pad, Paper guide, Front Sub...

Fusing Temperature Control Circuit Epson EPL 5700

Mon, 26 Sep 2011 10:01:29 GMT

The thermister TH1 detects the surface temperature of the fusing heat roller, and input analog voltage into IC201-78. According to the detected temperature, the heater lamp H1 is turned On or Off by the heater lamp On Off signal, which is input by IC201-55, and controls the temperature of the fusing part. The heater lamp is 450W. 3 different voltages are used according to the destination 100V, 120V and 230V. If the heat lamp is not turned off even when the thermister detects abnormally high...

Contents Epson Stylus Photo R300 R310

Mon, 26 Sep 2011 05:22:22 GMT

1.1 Overview 1.2 Troubleshooting with LED LCD Indications and Status Monitor 3 Message 9 1.3 Unit Level Troubleshooting 14 2.1.2 Tools 2.1.3 Pre-Shipment 2.2 Caution regarding assembling disassembling the printer mechanism, and how to ensure the quality of reassembled product 2.3.1 Removing Paper Support 2.3.2 Removing Housing, 2.3.3 Removing Housing, 2.3.4 Removing Porous Pad, Paper Guide, 2.3.5 Removing Panel 2.3.6 Removing Stacker 2.3.7 Removing Main Board 2.3.8 Removing ASF 2.3.9 Removing...

Info Qaw Epson Stylus Photo R300 R310

Mon, 26 Sep 2011 04:55:10 GMT

This adjustment is made to allow the PC to recognize the connected printers individually when multiple printers of the same model are connected and used with the PC via a USB hub. Select this function in the exclusive servicing program and enter the serial numbers of the printers. The correction value is saved to the specific EEPROM address on the Main Board. At the time of Print Head replacement, this adjustment is made to correct head manufacturing variations and eliminate the individual...

Epson Stylus Photo R280 Error Epson Stylus Photo R280 R285 R290

Mon, 26 Sep 2011 01:10:06 GMT

Flashes at intervals of 1.25 seconds. Flashes as follows ON 0.5 sec. - OFF 0.5 sec. - ON 0.5 sec. - OFF 1.0 sec. Flashes at intervals of 0.5 seconds. Flashes at intervals of 1.25 seconds. Figure 3-2. Error Indication on EPSON Status Monitor 3 Figure 3-2. Error Indication on EPSON Status Monitor 3 NOTE The part number of the Ink Cartridges shown in the Status Monitor 3 screen differs by destination.

Board Component Layout Epson EPL N2050

Sun, 25 Sep 2011 21:56:12 GMT

Figure 7-15. C305MAIN Component Layout The parts to which no reference number is assigned will not be available as after-sale service parts. The following pages show the circuit diagrams for the C305 Main Board. EPSON EPL-N2050 C305MAIN BOARD 2 of 3 EPSON EPL-N2050 C305MAIN BOARD 2 of 3

I Ubi Epson Stylus C63 C64 C83 C84

Sun, 25 Sep 2011 18:32:20 GMT

In case that Cap, Detector, PW is removed, PW sensor board is free. Therefore, be caureful not to damage PW sensor board. 13 Disconnect Head FFC from the connectors on print head board, and remove Print head assy. from IC holder. 13 Disconnect PW sensor FFC from the connector of PW sensor board. CR encoder sensor board removal 13 Release two hooks for securing CR encoder sensor board to IC holder, and disconnect CR encoder senser FFC from the connector of CR encoder sensor board. Make sure...

Info Mjj Epson Stylus Photo 895 785EPX

Sun, 25 Sep 2011 18:06:58 GMT

Initial setting for Set print mode 1 0x00 Premium Glossy Photo Paper, 0x10 Photo Quality Ink Jet Paper, 0x20 Plain Paper, 0x30 Photo Lower 4bits Default of Paper Size 0x00 89mm Roll, 0x01 127mm Roll, 0x02 4 Roll, 0x03 210mmRoll, 0x04 4x6, 0x05 Letter, 0x06 5x7, 0x07 8x10

Printer Mechanism Operation Epson FX 850 FX 1050

Sun, 25 Sep 2011 15:46:58 GMT

The printer mechanism is a 9-pin serial dot matrix impact mechanism. Figure 2-2 shows a drawing of the mechanism. The name in the rectangles indicate relationship between each mechanism and the control circuit on the PEGX board. Figure 2-2. Printer Mechanism Block Diagram Figure 2-2. Printer Mechanism Block Diagram The printer mechanism is composed of the following The printhead is an electromagnetic induction 9-pin serial dot head. Nine dot wires are driven individually to print a dot pattern...

Head Cleaning Epson Stylus Color 3000

Sun, 25 Sep 2011 12:09:27 GMT

In case abnormal printing occurs, you can enter the printhead cleaning mode through the control panel operation. Also, to keep the printer in the best condition, the printer automatically selects the cleaning level including flushing and carries it out even while printing. Follow the steps below to enter the printhead cleaning mode. 1. Press Pause button to put the printer into the off-line status. Pause LED goes off. 2. Clean the black or color printhead by pressing the corresponding Cleaning...

Interlock Switch and Cover Open Sensor Assembly Removal Epson DFX 8500

Sun, 25 Sep 2011 09:48:16 GMT

Step 1 Remove the upper case. Refer to Section 3.2.3.4 Step 2 Disconnect the interlock switch cable and the cover open sensor cable from the junction board respectively. Figure 3-38. Interlock Switch Assembly Removal Figure 3-38. Interlock Switch Assembly Removal Step 3 Remove the CBB M4x10 screw securing the interlock switch assembly to the lower case. and remove it. Step 4 Remove the CBB M3x10 screw securing the cover open sensor to the upper case. and remove it. Figure 3-39. Interlock Switch...

Overview Epson Stylus Photo 895 785EPX

Sat, 24 Sep 2011 10:21:51 GMT

This section describes the operating principles of the printer mechanism and electrical circuit boards. The Stylus PHOTO 895 785EPX has the following boards Power supply board C408 PSB PSE Monochrome panel board C408 PNL Printer panel board C408 PNL-B The printer mechanism for Stylus PHOTO 895 785EPX is designed newly. But, the basic component of the printer mechanism is same as previous product. This printer consists of Print Head, Carriage Mechanism, Paper Feeding Mechanism, Paper Loading...

How To Unlock The Epson R380 Epson Stylus Photo R260 R265 R270 R360 R380 R390

Fri, 23 Sep 2011 23:29:14 GMT

Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. 4.1.8 Sharp Metal Edges Danger p.62 Parts Components need to be removed in advance All exterior parts All control boards Middle Housing Printer Mechanism CR Scale Refer to the Orientation Definition below for the directions indicated in the following procedures. 4.1.6 Orientation Definition p.61 1. Remove the Extension Spring of the Driven Pulley Assy from the rear...

Info Nev Epson Artisan 700 800 Stylus Photo PX TX 700FW 800FW

Fri, 23 Sep 2011 21:07:00 GMT

Selects print quality from the options shown in Table 1-26. Selects zoom type from the 13 types below. Sets any zoom with - key 25 to 400 after selecting Actual Selects from Text, Text amp Image, Photo Selects from the nine density levels of -4 to -0 to 4. Selects the margins level margins bleed off the edges of paper from the Standard 100 , Mid. 50 or Min. 0 . 2 Note 1 Available when the Double-sided Printing Unit is installed. 2 Percentages in parentheses indicate the proportion of the margin...

Lcd 1 Epson Artisan 700 800 Stylus Photo PX TX 700FW 800FW

Fri, 23 Sep 2011 20:43:12 GMT

Figure 1-4. Control Panel Epson Artisan 800 Epson Stylus Photo PX800FW TX800FW Figure 1-4. Control Panel Epson Artisan 800 Epson Stylus Photo PX800FW TX800FW Display Crop button LCD Menu button -, button Cross Key and OK button Power LED Mode button . Print Tray button . Figure 1-5. Control Panel Epson Artisan 700 Epson Stylus Photo PX700W TX700W Table 1-22. Button Functions Epson Artisan 800 Epson Stylus Photo PX800FW TX800FW Displays available buttons in each mode. Release the lock of tilt...

Major Component Unit Epson Stylus CX4300 CX4400 CX5500 CX5600 DX4400 DX4450

Fri, 23 Sep 2011 07:06:41 GMT

Figure 7-1. Connection of the major components See the following tables for the connector summary of the Main Board and each connector's pin assignment. Table 7-1. Connector Summary for Main Board Table 7-1. Connector Summary for Main Board For connection with the CR Encoder Sensor and the CSIC Board. For connection with the Power Supply Board For connection with the USB interface The printer has a USB interface of the following specification. p.19 For connection with the Scanner Motor Table...

IC Bsv Epson Stylus Color 480SXU 580

Fri, 23 Sep 2011 06:37:05 GMT

The printhead drive circuit consists of the following two components Common driver IC7 amp Wave amplifier transistor Q1, Q2 Nozzle selector IC on the printhead driver board. The common driver IC7 generates a reference drive waveform according to the output signals from the CPU IC1 . The reference drive waveform is amplified by the transistors Q1 and Q2 and then transferred to the nozzle selector IC on the print head circuit board. Print data is converted to serial data by the CPU and then sent...

Paper Loading Mechanism Epson Stylus Photo RX420 RX425 RX430

Fri, 23 Sep 2011 03:23:18 GMT

The Paper loading mechanism consists of the Change Lever in the Pump Unit, the Holder Shaft Unit including the Clutch mechanism and the ASF Unit. The Change Lever and the Clutch mechanism play a major role in the Paper loading mechanism as follows. 1. ASF home position detection function The ASF Unit on this printer does not have the ASF Home Position Sensor. Instead of the ASF Home Position Sensor, the Change Lever and the Clutch mechanism is used to detect the ASF home position. When the...

HopperRetard Roller Unit CAUTION Epson Stylus C67 C68 D68

Thu, 22 Sep 2011 21:25:13 GMT

2 Lift up the Hopper toward the direction of the arrow, release the two tabs, and remove the spring and the hopper from the ASF Frame. 3 Remove Extension Spring 0.585 from both the ASF Frame and the Paper back Lever. 4 Remove the Paper Back Lever from the bearing of the ASF frame. 5 Remove Compression Spring 1.88 from the ASF Frame, and remove the Retard Roller Unit. Figure 4-8. Removing Retard Roller Unit Figure 4-8. Removing Retard Roller Unit When installing the Retard Roller or the Paper...

Info Reb Epson Stylus CX4100 CX4200 CX4700 CX4800 DX 4200 DX4800 DX4850

Thu, 22 Sep 2011 19:38:43 GMT

3. Check if the Panel Board is not damaged. 3. Replace the Panel Board with new one. Table 3-7. Check point for the communication error according to each phenomenon 1. Check if the PS Board Connector Cable is connected to the CN1 on the Main Board. 1. Connect the PS Board Connector Cable to CN1 on the Main Board. When turning on the power, the SPC does not operate at all. 1. Check if the PS Board Connector Cable is connected to the CN1 on the Main Board. 2. Check if the PS Board Connector Cable...

Capping Mechanism Epson Stylus Photo RX420 RX425 RX430

Thu, 22 Sep 2011 18:25:27 GMT

The Capping mechanism covers the Print Head with the Cap to prevent the nozzle from increasing viscosity when the printer is in stand-by state or when the printer is off. The wiping operation is controlled by the Carriage Unit movement. This operation is usually performed with every CL sequence which is to absorb the ink from the ink cartridge, the ink cavity by the Pump unit. Following figure shows you the mechanism for the wiping operation. When the Carriage Unit is in the home position, the...

Info Bqo Epson Stylus Photo 890 1280 1290

Thu, 22 Sep 2011 17:13:15 GMT

Figure 4-39. LEVER, HOPPER, RELEASE Installation Figure 4-40. LD Roller Assembly Installation 1 Figure 4-40. LD Roller Assembly Installation 1 When installing the edge guide to the left LD Roller Assembly, ensure that the rib in the LD Roller Assembly fits correctly into the groove in the edge guide. See Figure 4-41. Make sure that the right LD Roller Assembly is fixed with the hook in FRAME, ASF B. You can check its condition from the back of the ASF Unit. See Figure 4-42. Before assembling...

Disassembly And Assembly Epson Stylus C63 C64 C83 C84

Thu, 22 Sep 2011 15:38:14 GMT

This section describes procedures for disassembling the main components of the Stylus C63 64 83 84. Unless otherwise specified, disassembly units or components can be reassembled by reversing the disassembly procedure. Things, if not strictly observed, that could result in injury or loss of life are described under the heading Warning. Precautions for any disassembly or assembly procedures are described under the heading CAUTION. Chips for disassembling procedures are described under the...

CAUTION Do not damage the rubber rollers when removing the Roller EJ Assy Epson Stylus Photo R220 R230

Thu, 22 Sep 2011 14:41:37 GMT

Figure 2-45. Paper Guide, Front Roller EJ Assy. Removal 2 When installing the Paper Guide, Front to the Frame, Main Be careful not to damage the surface of the Roller PF Assy. Be careful not to damage the rib of the Paper Guide, Front or the Porous Pad, Paper Guide, Front. Check if the dowels and the tab of the Paper Guide, Front are correctly secured to the Frame, Main. Figure 2-47. Paper Guide, Front Installation Figure 2-47. Paper Guide, Front Installation Make sure that there is no gap...

Waste Ink Drain Pad Removal Epson Stylus Color 1520

Thu, 22 Sep 2011 10:45:07 GMT

Waste Ink Drain Pads must be replaced when the printer is under the following conditions The value for the protect counter A has reached the specified value 65,000 and the maintenance request error is indicated. The indicated value of the Protect counter is more than 52,000. In this case, be sure to replace them by agreement with your customer. The protect counter C has reached the specified value and the maintenance request error for the left ink pad is indicated. Refer to Section 1.4.11 and...

PF motor removal Epson Stylus Color 680 685 777 777i

Thu, 22 Sep 2011 06:27:52 GMT

1. Remove the Housing from the printer. Refer to Section 4.2.1. 2. Remove the Waste drain ink pad unit from the printer. Refer to Section 4.2.6. 3. Remove the Front frame and Paper eject roller. Refer to Section 4.2.10. 4. Remove the Plain washer and then remove the Combination gear 11.6, 36.8 Figure 4-41. Removing the Plain washer and Combination gear 11.6, 36.8 Figure 4-41. Removing the Plain washer and Combination gear 11.6, 36.8 5. Remove three nuts Hexagon Nut M3 securing the PF motor to...

Info Pmu Epson FX 2170

Thu, 22 Sep 2011 04:59:27 GMT

1 Plain paper weight 82 g m , 22 lb or recycled paper, except for A3-size paper. 2 Plain paper weight 82 g m2 , 22 lb or recycled paper, A3 paper. 3 Plain paper weight 64 g m2 , 17 lb , except for A3 paper. 4 Plain paper weight 64 g m2 , 17 lb , A3 paper. 5 Envelopes weight 91 g m2, 24 lb 6 Envelopes weight 45 g m2, 12 lb 7 Card stock weight 192 g m2, 51 lb thickness 0.22 mm, 0.0087 8 1 original 5 copies thickness 0.36 mm, 0.0142

Chapter Disassembly and Assembly 1 Epson EPL 5000 EPL 5200 ActionLaser 1000 1500

Thu, 22 Sep 2011 03:51:29 GMT

3.1.1 Precautions for 3.1.3 Small 3.1.4 Service Checks after 3.2 DISASSEMBLY AND ASSEMBLY_3-4 3.2.1 Removal ofthe Video Controller Section 3-4 3.2.1.1 Video Controller Board C108 MAIN Removal 3-4 3.2.1.2 PCL5 RITech Upgrade Board C82907 ROM-B Removal 3-5 3.2.1.3 Control Panel 3.2.2 Housing 3.2.2.1 Case 3.2.2.2 Rear Frame f. 3.2.3 Disassemblingthe 3.2.3.1 Engine Controller Board PWB-A Removal 3-8 3.2.3.2 Power Supply Unit PWB-E Removal 3-9 3.2.3.3 Interlock Switch 3.2.3.4 Printhead Unit 3.2.3.5...

Info Kqt Epson EPL 5000 EPL 5200 ActionLaser 1000 1500

Thu, 22 Sep 2011 03:36:53 GMT

Check the surface of image transfer roller. Check if there is any dust or damage on the fusing roller surface.

Removing the Panel Board Assembly Epson FX 2180

Thu, 22 Sep 2011 01:08:45 GMT

1. Remove the printer cover and ribbon cartridge. Refer to Section 4.2.1. 2. Release the left clips for the panel board assembly by pushing them from the cutout located on side front of the upper housing assembly. 3. Release FFC flexible flat cable by pulling the lock cover for CN1, and then disconnect the FFC for CN1 and connector CN2 from the C165 PNL board assembly. 4. Remove the panel board assembly from the upper housing assembly. M Before disconnecting the FFC from CN1, slide the lock...

Panel Board Epson Stylus C67 C68 D68

Thu, 22 Sep 2011 01:08:17 GMT

2 Disconnect the Panel Board Connector CN4 from the Main Board. See 4.3.2.1 Removing Main Board Step 3 3 Release the Panel Board from the two tabs and the notch of the Holder Shaft Unit. Figure 4-28. Routing Panel Board Connector Figure 4-28. Routing Panel Board Connector 2 Disconnect the Power Supply Cable CN2 from the Main Board. See 4.3.2.1 Removing Main Board Step 3 3 Remove the three screws that secure the PS Board Unit to the Main Unit, and remove the PS Board Unit. 4 Release the two tabs...

Info Daj Epson Stylus Color 600

Wed, 21 Sep 2011 21:19:05 GMT

The piezo-electric element used in each printhead unit has unique electrical characteristic and the electrical characteristic of each printhead is measured at the production and each printhead unit is given with the ID code. Therefore, this ID code is need to be stored in EEPROM on the main board when the following service is made and the printer read this information to compensate the difference of characteristic for printing control and an amount of injected in k is maintained at the...

Acaution Cxg Epson Stylus Color 600

Wed, 21 Sep 2011 21:17:57 GMT

0 Since this operation consumes large amount of ink, do not perform it unnecessarily Black Approx. 8.8 of the ink charged in the cartridge Color Approx. 16.2 of the ink charged in the cartridge CMY total 1. Re-assemble the printer after replacing the component. It is enough that, at least, the printer mechanism, the electrical circuits and the control panel are connected. 2. Connect the PC to the printer and turn the printer on. Then, unpack a brand-new ink cartridges and install them on to the...

Dtr 1 Epson Stylus Color 3000

Wed, 21 Sep 2011 20:28:56 GMT

Serial Interface Connector Pin Assignment Serial Interface Connector Pin Assignment The EPSON Stylus COLOR 3000 supports an optional Type-B interface Level 2 with the following characteristics. In case of using Co-ax Twin-ax I F card Main type MTP48p, PW161cl10cpi, PRG W0xxxx rev, AP800ma, Product name Stylus COLOR 3000 Main type MTP48p, PW161cl10cpi, PRG W0xxxx rev, AP800ma, Product name Stylus COLOR 3000 Emulation type PRPXL24-00 Entity type EPSONPRPXL24 In case of using an I F card other...

Info Nvh Epson ColorPage EPL C8000

Wed, 21 Sep 2011 14:29:09 GMT

Check FRONT COVER SWITCH L for its pushing motion Is the actuator in the FRONT COVER ASSY functioning properly as follows With the diagnostic tool, go to step 4. Without the diagnostic tool, go to step 5.

Levelness Adjustment of the Bin Unit Epson EPL N2700 Optional Units

Wed, 21 Sep 2011 13:43:51 GMT

1. Remove the covers from the both legs of the 10-Bin Unit. 4. If the knob is turned counterclockwise, the 10-Bin Unit moves in the direction shown in the figure below. 3. Turn the knob attached to each leg of the unit to adjust its standing position. 5. After the standing position has been adjusted, tighten the wing bolts. 6. Reinstall the covers onto the legs of the 10-Bin Unit.

General Repair Information Epson FX 850 FX 1050

Wed, 21 Sep 2011 06:31:03 GMT

This chapter describes the disassembly procedures to be used for replacing any of the main components of the FX-850 1 050. Required and helpful tools, measuring instruments, and lubricants listed in Tables 4-1 through 4-3. o Commercially available product E EPSON exclusive tool O Commercially available product E EPSON exclusive product Figure 4-1 shows some of the parts found on the FX-850 1050. Figure 4-1 shows some of the parts found on the FX-850 1050. DIP Switches Platen Knob Paper Release...

Info Spv Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Wed, 21 Sep 2011 01:48:33 GMT

The wiping mechanism is activated by the capping operation. The mechanism moves the wiper into- and out-of position for cleaning the head using the PF motor drive force that is transmitted via the cam of the clutch-equipped combination gear. Non cleaning state clutch disengaged In the non-cleaning state, the cap slider protrusion secures the cam and the clutch of the combination gear is disengaged. Therefore, the PF motor drive force is not transmitted to the cam. Groove of Wiper protrusion cam...

Info Kka Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Wed, 21 Sep 2011 01:47:40 GMT

Table 3-9. Check point for Paper out error according to each phenomenon The drive of the PF Motor is not transmitted to the LD Roller Shaft. 1. Check if the Extension Spring 0.143 does not come off in the Clutch mechanism. 1. Reassemble the Extension Spring 0.143 in the Clutch mechanism. 1. Check if the Extension Spring 0.143 does not come off in the Clutch mechanism. 2. Check if the positioning hole of the Clutch does not come off from the guide pin of the LD Roller Shaft. 3. Check if the...

Info Fhg Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Wed, 21 Sep 2011 01:06:42 GMT

Step2 Releasing Clutch Lever to Drive LD Roller When the PF motor pinion gear starts clockwise rotation as seen from the left side , the change lever is moved toward the front of the printer to release the clutch lever. This causes the clutch to engage with the gear by being pulled by the extension spring. The clutch gear engages with the clutch lock tab and the PF motor drive force is now can be transmitted to the LD roller shaft. After the engagement of the clutch, the PF motor pinion gear...

Sequential Repair Adjustment Program Epson Stylus Photo 890 1280 1290

Wed, 21 Sep 2011 00:57:03 GMT

This program is common for both Stylus Photo 890 and Stylus Photo 1290. NOTE In this section, Stylus Photo 890 program windows are used as examples. In this section, the sequential operations needs to be done are explained. This service program provides appropriate adjustment orders for repair, and the following adjustment items are included Carriage Unit Replacement Removal Printer Mechanism Replacement 1. Start the program and input all the required information on the initial window. Make...

Info Tvr Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Wed, 21 Sep 2011 00:42:05 GMT

The carriage mechanism components include the carriage unit including printhead, CR encoder sensor , CR motor, timing belt, and CR scale. The operating principles of the carriage mechanism are described below. Main Frame CR Scale CR Encoder Sensor CR Motor Main Frame CR Scale CR Encoder Sensor CR Motor This printer employs closed-loop control, via the CR motor and an encoder, to control the carriage speed and position. Since the CR motor is DC motor, the printer controls the motor in the...

Disassembling the Scanner Unit UpperFront Scanner Housing Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Tue, 20 Sep 2011 22:20:52 GMT

Parts Components need to be removed in advance Document Cover ASF Cover Scanner Unit Following work should be performed in a room where there is a little dust. A clean room or a clean bench would be preferable. Do not scratch the Rod Lens Array when removing the CIS Assy. If the Hinge R or the Driven Pulley comes off during disassembling, reassemble them as shown in the figure below. Figure 4-104. Installing the Hinge R or the Driven Pulley Figure 4-104. Installing the Hinge R or the Driven...

S Dfa Epson Stylus Color 880

Tue, 20 Sep 2011 14:25:17 GMT

H I I lOl I M Figure 7-2. C378MAIN Component Layout Figure 7-3. C378PSB Component Layout Figure 7-3. C378PSB Component Layout Figure 7-4. C378PSE Component Layout Figure 7-4. C378PSE Component Layout Figure 7-5. C298PNL Component Layout Figure 7-5. C298PNL Component Layout

Grounding Spring Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Tue, 20 Sep 2011 11:24:45 GMT

Parts Components need to be removed in advance Document Cover ASF Cover Scanner Unit Panel Unit Upper Housing Card Slot Cover Lower Housing Main Board Unit Left Frame PF Encoder Sensor PF Scale 1. Release the PF Motor connector cable from the notches x2 of the Base Frame. Figure 4-61. Removing the PF Motor 1 Figure 4-61. Removing the PF Motor 1 2. Remove the Grounding Spring from the PF Motor. 3. Remove the screws x3 that secure the PF Motor, and remove it. I l Guide Pin and Positioning Hole O...

Main Frame Assy Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Tue, 20 Sep 2011 11:23:56 GMT

Parts Components need to be removed in advance Document Cover ASF Cover Scanner Unit Panel Unit Upper Housing Card Slot Cover Lower Housing Main Board Unit Left Frame Front Frame Right Frame CR Motor CR Scale Hopper B Main Frame Assy consists of the following parts. 1. Remove the Grounding Spring from the PF Motor. Refer to 4.5.11 PF Motor Step2 p119 2. Release one end of the Extension Spring from the hook of the Main Frame with longnose pliers, and then remove the spring together with the...

Disassembly and Assembly of CSF Bin Epson FX 2180

Tue, 20 Sep 2011 09:32:25 GMT

This section describes procedure for disassembling and assembling the operational cut sheet feeder. In general, you can install a component in the CSF simply by reversing the procedure for removing. Therefore, this section dose not describe assembly procedures in most cases. If necessary, special notes on assembling a component are given at the end of description of each procedure. 4.2.10.1 Disassembling the Right Side Block 1. Remove the CFS gear cover by pushing and releasing the 4 clips in...

I Erk Epson Stylus CX4100 CX4200 CX4700 CX4800 DX 4200 DX4800 DX4850

Tue, 20 Sep 2011 07:07:45 GMT

This adjustment requires the FT Function Test program and the exclusive adjustment jig. If the setting of the printer differs from the one mentioned in the following procedure, this adjustment could not be completed correctly. In that case, the edge of the Scanner Housing, Upper may be read in during scanning or copying. 1. Hold down the Color Start Paper Size Fit to Page and turn the printer on. Keep pressing those buttons for five seconds, and the printer turns to the scanner mode. This...

Info Ehr Epson AcuLaser Color 2000

Tue, 20 Sep 2011 06:50:59 GMT

1 Standard mode 9000pages 30,000images Calculated assuming B W 4,500pages 3P J 7,500images , Color 4,500pages 2P J 22,500images The Photoconductor life varies according to the type of printing continuous, intermittent . 1 Standard mode 9000pages 30,000images Calculated assuming B W 4,500pages 3P J 7,500images , Color 4,500pages 2P J 22,500images The Photoconductor life varies according to the type of printing continuous, intermittent . 389 W x 105 D x 69 H mm Approx. 780g Photoconductor unit...

Epson R290 Delete All Print Jobs And Turn The Printer Off. Remove Any Foreign Objects From Inside The Printer. After A Few Minutes Turn The Printer Back On. Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Tue, 20 Sep 2011 06:44:04 GMT

RAM trouble occurs. System trouble occurs. A printer error has occurred. Turn off the printer, then press On button to turn on. See your documentation. Delete all print jobs and turn the printer off. Remove any foreign objects from inside the printer. After a few minutes, turn the printer back on. Maintenance error waste ink overflow Waste ink pad in the printer is saturated. Contact your dealer to replace it.

Assembly Vce Epson EPL N2050

Mon, 19 Sep 2011 20:43:09 GMT

1. Align the PWB ESS with its mount position to the printer. 2. Shifting the PWB ESS toward the front of printer, plug the connector of PWB ESS to the connector P J of PWBA MCU. 3. Secure the PWB ESS to the printer with five screws. 4. Plug the connector P J to the PWB ESS. 5. Plug the connector P J to the PWB ESS. 6. Mount the Cover Assy I F Section 4.2.2 .

I Jjp Epson Stylus Pro 7600 9600

Mon, 19 Sep 2011 19:54:00 GMT

When unlocking the carriage, do not move the carriage by about 2 cm or more with the cutter pushed into the innermost position otherwise, the cutter edge would be damaged. Take great care not to scratch the CR Encoder Scale. If the CR Encoder Scale is scratched, the encoder sensor will output wrong signals, thus resulting in abnormal operation of the carriage or error occurrence. 1. Remove the R Side Cover. p.160 2. Remove the L Side Cover. p.163 3. Remove the I H Cover. p.164 4. Remove the H...

Info Ift Epson Stylus Photo 870 1270

Mon, 19 Sep 2011 16:38:21 GMT

If you need to check for the model name you have input, select Check this model name and click OK. The printer is reset and displays the model name. 5. To exit the program, click Continue repeatedly or press the ESC key to return to the initial window, and then click Quit. You see the small quit window, where click OK to exit the program. Using this function, you can check that the correct destination is stored in EEPROM on the main board by reading the model name. The destination information...

Info Ite Epson Stylus Photo R260 R265 R270 R360 R380 R390

Mon, 19 Sep 2011 15:50:53 GMT

Removing the Main Board Unit p.78 The CDR Guide is set correctly, but the error occurs. 1. Is the CDR Guide Detection Assy cable not connected to the Main Board 1. Connect the cable to the Main Board. R360 R380 R390 Main Board CN9 R260 R265 R270 Main Board CN4 4.5.15 CDR Guide Detection Assy p.111 2. Replace the CDR Guide Detection Assy. 3. Is the CDR Guide Detection Assy cable broken 3. Replace the CDR Guide Detection Assy. 1. Is the CDR Guide Lever not installed correctly 1. Install the CDR...

Control Circuit Operation Overview Epson LQ 570 LQ 1070

Mon, 19 Sep 2011 13:58:55 GMT

The printer CPU is an 8-bit CPU TMP90C041 running at 10 MHz. It oversees control of all the components of the printer. The E05A50 gate array contains various memory management functions that control the assignment of the memory and I O areas. Rationalization and simplification of the circuitry is achieved through use of the STK-6022B, which holds all the driver circuits for driving the PRINTER MECHANISM on a single chip. Figure 2-17 shows the control circuits in block diagram form. I 1...

I Fjr Epson Artisan 700 800 Stylus Photo PX TX 700FW 800FW

Mon, 19 Sep 2011 13:28:01 GMT

When printing the CDR, the CDR Tray feed amount is adjusted with compensation depending on the deterioration of the CDR Tray, and the correction level is determined by the number of printed CDRs. If the data on the EEPROM can not be copied when replacing the Main Board, banding may occur while printing CDR due to improper corrections caused because the data of the number of printed CDRs can not be transferred. When this happens, replace the CDR Tray Assy with a new one together with the Main...

Info Pxi Epson Stylus CX4100 CX4200 CX4700 CX4800 DX 4200 DX4800 DX4850

Mon, 19 Sep 2011 08:03:59 GMT

O C.B.P. 3x10 F Zn 4 1kgfcm O C.B.S. 3x6 F Zn 7 1kgfcm O C.B.P. 3x10 F Zn 4 1kgfcm O C.B.S. 3x6 F Zn 7 1kgfcm Part Unit that should be removed before removing Housing, Upper Document Cover Paper Support Assy. Scanner Unit Panel Unit Removal procedure 1. Remove the screws x6, o that secure the Housing, Upper. 2. Release the tabs x2 that secure the Housing, Upper with a flathead screwdriver or a similar tool, and lift up to remove the Housing, Upper. Document Cover Paper Support Assy. Scanner...

Fuser Control Epson EPL 5000 EPL 5200 ActionLaser 1000 1500

Mon, 19 Sep 2011 07:35:40 GMT

The fuser is heated by the heater lamp, which is powered by AC voltage. When the power supply board receives a FUSER LAMP signal from the engine controller board PWB-A , the power supply board PWB-E supplies the AC voltage to the heater lamp. This AC voltage is cut by the interlock switch when the case is open. The fuser temperature is detected by the thermistor. Based on the TH1 signals from the thermistor, the engine controller board PWB-A controls the fusing temperature 165 C, 329 F using...

Troubleshooting with LED Error Indications Epson Stylus Color 880

Sun, 18 Sep 2011 22:40:23 GMT

This section describes how to troubleshoot the problem when the printer indicates an error at power on and can not print. The Stylus COLOR 880 can detect the following six errors and seven status, and indicates them with the LEDs, as shown below. Table 3-3. Error Indication of Operation Panel Table 3-3. Error Indication of Operation Panel

APG Unit Epson Stylus Photo R280 R285 R290

Sun, 18 Sep 2011 17:34:23 GMT

Parts Components need to be removed in advance Printer Cover Paper Support Assy Upper Housing 1. Remove the two screws taking care not to lose the gears, and remove the APG Unit. Screw C.B.S. M3x6 tightening torque 7-9 kgf.cm No.1 The numbers shown in the figure indicate the order of tightening the screws. 2. Remove the Combination Gear 10, 15.2 . Figure 4-56. Removing the Combination Gear 10, 15.2 Figure 4-56. Removing the Combination Gear 10, 15.2 Lubrication is required. See the page given...

Info Vcz Epson Stylus Photo RX420 RX425 RX430

Sun, 18 Sep 2011 15:35:12 GMT

Approx. 10W Standalone copying, IS010561 Letter Patter, Plain Paper - Text Note 1 This product complies with the Energy Star standards. 2 If the printer is not operated at all for at least three minutes, the standby function reduces the current to the motor to conserve power. 3 If the scanner is not operated at all for at least four minutes, the standby function reduces the current to the motor to conserve power. 10MQ minimum tested between AC line and chassis, test voltage DC500V AC1000Vrms...

A Rci Epson Stylus Photo RX420 RX425 RX430

Sun, 18 Sep 2011 15:29:31 GMT

Close loop control based on the CR Motor DC Motor and CR Encoder has advantages in stabilized print quality. Using low-cost DC motors, this product grasps the variations of the torque constants, coil resistances and power supply voltages of the individual DC motors adequately to carry out heat generation control according to individual differences. CR variation measurement sequence The variations of the torque constant, coil resistance and power supply voltage of the motor are measured in a CR...

REASSEMBLY Uqx Epson Artisan 700 800 Stylus Photo PX TX 700FW 800FW

Sun, 18 Sep 2011 15:07:40 GMT

Figure 4-5. Removing the ADF Unit 2 Insert the terminal of the Grounding Wire to the end of the rib of the Frame. See Fig. 4-4. For routing cables, see 4.4 Routing FFC cables p202 . When installing the Cable Cover, secure it with a new Harness Cover Clamp. See Fig. 4-3. The disassembly reassembly procedures of Artisan 700 PX700W TX700W differ from those of Artisan 800 PX800FW TX800FW. See 4.3.1.1 Scanner Unit Artisan 700 PX700W TX700W p185 for the procedures. Parts Components need to be removed...

MicroAdjustment TopofForm Set Function Epson FX 850 FX 1050

Sun, 18 Sep 2011 12:18:35 GMT

After paper loading is completed, set the printer ON LINE by pressing the ON LINE switch. In this state, the paper loading position can be finely adjusted by operating the LF and FF switches. When the printer is in the micro adjustment mode, the ON LINE LED on the panel blinks. The paper loading position can be adjusted individually for the friction feed, tractor feed, and cut sheet feeder modes, and the adjusted values are stored in the memory. The value for the tractor feed remains valid even...

Adjustment Program Initial Setting menu Epson Stylus Color 480SXU 580

Sun, 18 Sep 2011 00:18:02 GMT

You have to input the following four items before entering the adjustment main menu. Select the required model name in the model Name list. You can sleet the Stylus COLOR 480SXU also in the latest adjustment program Ver. 2.0 Interface setting EPUSB1, EPUSB2, EPUSB3 Program type Individual service adjustment program or Sequential repair service program Follow the procedure below to input the initial settings. 1. When you run this program, the following menu appears. Select the Stylus COLOR 580...

Head ID Input Function Epson Stylus Photo 2100 2200

Sat, 17 Sep 2011 19:58:51 GMT

This function is designed to correct ink discharge amount variations due to individual manufacturing differences between Printheads when the Printhead is replaced. 1. Choose the Head ID of the adjustment program. 2. Enter the 25-digit code of the Head ID label applied to the Printhead. Enter the Head ID from left to right on the top row and from top to bottom in due order.

REASSEMBLY Taj Epson Stylus CX9300F 9400fax dx9400f

Sat, 17 Sep 2011 15:01:35 GMT

When installing the Diffusion Sheet, Waste Ink Cover, and the Waste Ink Pads x3 on section B, attach them in the order given in the figure below. Figure 4-103. Installing the Waste Ink Pads When installing the Waste Ink Cover, be sure to align the dowel x1 of the Base Frame with the positioning hole x1 of the Waste Ink Cover as shown in Figure 4-102. Make sure to confirm the cover is properly secured on the Diffusion Sheet without any gap. Whenever the Waste Ink Pads is removed replaced, the...

APG Unit removal Epson Stylus Photo R200 R210

Sat, 17 Sep 2011 14:43:09 GMT

Figure 2-18. APG Unit removal Figure 2-18. APG Unit removal Parts Units which should be removed before removing APG Unit Paper Support Assy. Housing left right Housing frame ASF Unit Board, Main 1. Disconnect the APG motor connector cable from the connector CN13 of Main Board. 2. Remove the screw x1 for securing APG Unit, and remove the APG Unit carefully. When reassembling APG Unit, Make sure that the hooks x2 and the dowels x2 of APG Unit are securely attached to Frame, Main. Check if the...

Overview 1 Epson Stylus Photo 890 1280 1290

Sat, 17 Sep 2011 14:00:11 GMT

This chapter describes procedures for disassembling the main components of the EPSON Stylus Photo 890 1280 1290. Unless otherwise specified, disassembly units or components can be reassembled by reversing the disassembly procedure. Therefore, no assembly procedures are included in this chapter. Precautions for any disassembly or assembly procedure are described under the heading CAUTION and CHECK POINT. Any adjustments required after disassembling the units are described under the heading...

Disassembly And Assembly Epson FX 870 FX 1170

Sat, 17 Sep 2011 05:17:02 GMT

3.1.3 Service Checks After 3.1.4 Screw 3.2 Disassembly and 3.2.1 Pre-disessembly 3.2.2 Removing the PANEL 3.2.3 Removing the 3.2.4 Removing the HOUSING ASSEMBLY, 3.2.5 Removing the PRINTER 3.2.5.1 Removing the PLATEN 3.2.5.2 Removing the FRAME ASSEMBLY, REAR 3-11 3.2.5.3 Removing the MOTOR ASSEMBLY, CR 3-12 3.2.5.4 Removing the MOTOR ASSEMBLY, PF 3-13 3.2.5.5 Disassembling the GEAR TRAIN, 3.2.5.6 Removing the CARRIAGE GUIDE ASSEMBLY 3-15 3.2.5.7 Removing the Ribbon Drive RD ASSEMBLY 3-17...

Electric Circuit Epson Stylus CS3100 CX3200

Sat, 17 Sep 2011 01:10:10 GMT

The electric circuit boards of Stylus CX3100 3200 are as follows C497MAIN Board main circuit board C497PSB C497PSE Board power supply circuit board This circuit board supplies the following voltages Table 2-1. Functions of Major Elements - C497MAIN Table 2-1. Functions of Major Elements - C497MAIN Built-in RAM 10kB, Built-in Flash ROM 256KB Control, image processing C90A20 64Mbit Flash ROM Stores firmware Panel sensor input and output control Storage of default setting and backup of various...

Table Repair of the CZC PSBIPSE Board Epson Stylus Color 440 640 740

Fri, 16 Sep 2011 23:57:04 GMT

The printer does not operate at all. Feed back transistor Q2, Q3 are dead. Check the waveform at the drain of Q1.

Eeprom Epson Stylus Color 3000

Fri, 16 Sep 2011 21:53:42 GMT

IC17, IC18 for the pump motor and PF motor Head common driver hybrid ICs IC22, IC23 . PF Motor Driver CR Motor Driver PF Motor Driver CR Motor Driver Figure 1-13. C203 MAIN Board Component Layout Figure 1-13. C203 MAIN Board Component Layout C172 PSB PSE board, same as for Stylus COLOR 1500, consists of the transformer, switching FET, regulator IC on the secondary circuit, diode bridge, fuse, and so on. Figure 1-14. C172 PSB PSE Board Component Layout Figure 1-14. C172 PSB PSE Board Component...

Chapter Maintenance Epson DFX 8000

Fri, 16 Sep 2011 20:32:04 GMT

6.1 PREVENTIVE 6.2 LUBRICATION AND ADHESIVE Figure 6-1. Correct Adhesive Figure 6-2. DFX-8000 Lubrication and Adhesive Diagram 1 6-4 Figure 6-3. DFX-8000 Lubrication and Adhesive Diagram 2 6-5 Figure 6-4. DFX-8000 Lubrication and Adhesive Diagram 3 6-6 Table 6-1. Lubricants and Table 6-2. Lubrication Table 6-3. Adhesive Application Proper maintenance is essential to maintain optimal printer performance for the longest possibly period and to minimize malfunction frequency. Preventive maintenance...

I Edo 1 Epson Stylus Photo

Fri, 16 Sep 2011 19:12:09 GMT

Figure 2-23. EEPROM Circuit Block Diagram The Timer IC mounted on the C209 main board counts how long the printer is not used. The lithium-battery BAT1 is mounted on the board and performs power supply to the Timer IC when the Figure 2-24.Timer Circuit Block Diagram Figure 2-24.Timer Circuit Block Diagram The followings explain about operation of this circuit. When the printer is on, power is supplied to the Timer IC by applying 5V through the D4. This power is also used to oscillate the outer...

Info Gfg Epson Stylus CX4100 CX4200 CX4700 CX4800 DX 4200 DX4800 DX4850

Fri, 16 Sep 2011 18:54:19 GMT

X-Detected Position 238 pixel 600dpi Y-Detected Position 268 pixel 600dpi X-Correction Value -18 pixel 1200dpi Y-Correction Value 20 picxel 600dpi X-Offset Value -18 pixel 1200dpi Y-Offset Value 20 picxel 600dpi Figure 5-21. Window displayed when the adjustment is completed successfully 1 Figure 5-21. Window displayed when the adjustment is completed successfully 1 EPSON Scanner Function Test - C592B00W

Figure Fuser Control Circuit Epson EPL 5600 ActionLaser 1600

Fri, 16 Sep 2011 16:49:46 GMT

The following figure shows the fuser temperature control procedure. The following figure shows the fuser temperature control procedure. Figure 2-20. Temperature forFuser Control Procedure Figure 2-20. Temperature forFuser Control Procedure If the following renditions are detected, the printer indicates a fuser error the LCD displays SERVICE REQ. E0003 . . The thermistor temperature does not reach 55 C 131 F within 15 seconds. . The warm-up period doesnotend within 120 seconds. The thermistor...

Appendix Epson FX 850 FX 1050

Fri, 16 Sep 2011 11:26:24 GMT

A.1IC A.1.1 CPU LLPD781OHG A.1.2 Gate Array E05A15HA A.1.3 Gate Array E05A16GA A. 1.4 HM27256G-25 EP-ROM A-1 9 A.1.5 HM6264ALSP-12 CMOS ST-RAM A.1.6 NJM2355 A.1.7STK6722H4-Phases Stepper Motor Driver A-24 A.2 EXPLODED DIAGRAMS AND Figure A-1. ptPD7810 781 1 Pin Figure A-2. xPD781 0 781 1 Block Figure A-3. OP Code Fetch Figure A-4. Memory Read Figure A-5. Memory Write Figure A-6. GA E05A15HA Pin Diagram Figure A-7. GA E05A15HA Internal Block Diagram A-8 Figure A-8. GA E05A16GA Pin Diagram 3...

Artisan 700-800 Epson Artisan 700 800 Stylus Photo PX TX 700FW 800FW

Fri, 16 Sep 2011 08:21:06 GMT

The disassembly reassembly procedures of Artisan 700 PX700W TX700W differ from those of Artisan 800 PX800FW TX800FW. See 4.3.1.3 Upper Housing Artisan 700 PX700W TX700W p188 for the procedures. Parts Components need to be removed in advance ADF Unit Artisan 800 PX800FW TX800FW only Scanner Unit Upper Left Housing Paper Guide Top Assy 1. Remove the screw x1 and release the Grounding Wire. 1. Remove the screw x1 and release the Grounding Wire. Figure 4-15. Releasing the Grounding Wire 2. Release...

Paper Feed Mechanism Epson DFX 8500

Fri, 16 Sep 2011 07:32:41 GMT

Figures 2-7, 2-8, and 2-9 show the paper feed mechanism. After the printer loads the paper, it is fed by the tension roller, platen roller, and front or rear tractor assembly. The PF motor rotates the tension roller and tractor select gear Figures 2-8 and 2-9 and moves either the front or rear tractor assembly. The rotation of the paper feed transmission gear rotates the tractor select gear, which can engage either tractor train. The tractor select mechanism alternates the engagement of the...

Control Panel Removal Epson Stylus Color 670

Fri, 16 Sep 2011 07:00:38 GMT

1. Remove the Housing. SeeHousing Removal on page 72 2. Remove 2 screws securing the Control Panel, then remove the Control Panel from the Printer Mechanism. 3. Remove the screw securing the Left Housing Panel to the Printer Mechanism. 4. Remove 2 screws securing the Panel Board Assembly to the Printer Mechanism, then remove C209PNL Board from the Panel Assembly. 5. Remove FFC from the connector on the C209PNL Board. By removing the Control Panel, the Stacker Assembly can be also detached from...

Clean Head Epson Stylus Pro 7600 9600

Fri, 16 Sep 2011 02:49:00 GMT

When Head replacement is required on the service site, execute ink discharge InkBlowing in this mode beforehand. If transition in the sequence can not take place for some reason, the display shows Reset I C. When replacing the print head, execute ink discharge InkBlowing by using this function. Prepare seven draining cartridges, which are necessary for this work. Opener I C in the menu display must be understood as Draining Cartridge. In the flow as shown at right, upon completion of the first...

Error Fatal Epson Cx7300 Epson Stylus CX7300 CX8300 TX200 TX400 SX200 NX200

Fri, 16 Sep 2011 01:29:53 GMT

Table 3-5. Check point for Fatal error according to each phenomenon 1. Check if the PF Scale is not damaged or contaminated. 1. Replace the PF Scale with a new one. The eject rollers are rotating at high speed when power is turned on. For about 1 cycle. 1. Check if the PF Scale is not damaged or contaminated. 2. Check if the PF Encoder Sensor is not damaged. 1. Replace the PF Scale with a new one. 2. Replace the PF Encoder Sensor with a new one. The Scanner Carriage Unit does not operate. 1....

Info Ymw Epson Artisan 700 800 Stylus Photo PX TX 700FW 800FW

Thu, 15 Sep 2011 18:03:07 GMT

Parts Components need to be removed in advance Scanner Unit ADF Unit Scanner Upper Housing 2. Disconnect the Cover Open Sensor FFC from the connector of the Cover Open Sensor, and remove the Cover Open Sensor from the Scanner Lower Housing. Some of the parts of Artisan 800 PX800FW TX800FW differ from those of Artisan 700 PX700W TX700W. Unless otherwise specified, this section describes the procedures for Artisan 800 PX800FW TX800FW. The differences that may affect the disassembly reassembly...

Info Xbe Epson Stylus Color 860 1160

Thu, 15 Sep 2011 17:46:00 GMT

EPSON STYLUS COLOR 1160 No.1 Rev.01 10132 for EAI 220V ,EUR, S.E.ASIA. EAL,RUSSIA EPSON STYLUS COLOR 1160 No.1 Rev.01 10132

C MAIN Board Unit Removal Epson DFX 8500

Thu, 15 Sep 2011 15:04:53 GMT

Step 1 Remove the bottom panel assembly. Refer to Section 3.2.4.1 Step 2 Remove the C204 SUB board unit Refer to Section 3.2.4.3. Step 3 Remove the C204 DRV-B board and C204 DRV board units Refer to Section 3.2.4.4. Step 4 Disconnect connectors CN6, CN7, CN8, and CN10. Figure 3-31. C204 MAIN Board Removal 1 4 Figure 3-31. C204 MAIN Board Removal 1 4 Figure 3-32. C204 MAIN Board Removal 2 4 Figure 3-32. C204 MAIN Board Removal 2 4 Figure 3-33. C204 MAIN Board Removal 3 4 Figure 3-33. C204 MAIN...

Using the Control Panel to Configure the Printer Epson Stylus Pro 9000

Thu, 15 Sep 2011 13:12:21 GMT

In addition to testing the printer and checking the status of various components, you can use the SelecType menus to configure printer settings and perform maintenance operations. The following table lists the menus, their functions, and where to find additional information Print a nozzle check or status check Register paper thickness and drying time, and select registered configurations

I Swx Epson Stylus Photo RX420 RX425 RX430

Thu, 15 Sep 2011 12:11:05 GMT

The Scanner Carriage FFC is fastened with the double-sided tape, so be careful not to damage FFC. Figure 4-8. Scanner Carriage Unit Removal 1 Figure 4-10. Scanner Carriage Unit Removal 2 Figure 4-10. Scanner Carriage Unit Removal 2 Remove CIS Unit from Scanner CR Holder with opening and shifting it to the right direction. Remove CIS Spring x2 from Scanner CR Holder. Install CIS Spring by fastening the leg of CIS Spring to the dowel xl, of Scanner CR Holder. Release the hooks x2, for securing...

Info Wru Epson Stylus Color 980

Thu, 15 Sep 2011 11:07:34 GMT

80 95 F Figure 1-7. Temperature Humidity of Range Operating 1G, within 1 ms Non-operating 2G, within 2 ms 1 Resistance to vibration Operating 0.15G Operating 1 With a shipment container 2 Without condensation 75,000 pages A4, Letter 4000 million dots nozzle

I Djn Epson Stylus Photo R300 R310

Thu, 15 Sep 2011 09:24:01 GMT

Never use chemical solvents, such as thinner, benzine, and acetone to clean the exterior parts of the printer like the housing. These chemicals may deform the components of the printer or deteriorate the quality of the printer. Be careful not to damage any components when you clean inside the printer. Do not scratch the surface of the PF Roller. Use a soft brush to wipe off dust. Use a soft cloth moistened with alcohol to remove ink stain. Use a clean soft cloth moistened with water and wipe...