The latest Tractor and Truck Pulling For Salehttp://www.racingjunk.com/category/1090/Tractor-and-Truck-Pulling.htmlCopyright 2005-2013 racingjunk.com All Rights Reservedsupport@racingjunk.com (RacingJunk Classifieds Support)Thu, 20 Jun 2013 04:32:24 -0400Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/2814390/82-s-10-pulling-truck-t-k-OR-rolling.htmlGOT IT OUT OF THE GARAGE TODAY(5/7/13)FOR THE FIRST TIME SINCE OCTOBER. DONE A FRESH TUNE UP(NEW PLUGS,OIL CHANGE,NEW 16 VOLT BATTERY,NEW 112 RACING FUEL)OVER $500 SPENT ON IT TODAY!!!! IT IS NOW READY ONCE AGAIN FOR A NEW OWNER!!!MAKE ME A REASONABLE CASH OFFER AND I WILL SELL IT TO YOU CHEAP!!! I JUST NEED IT GONE AND OUT OF MY WAY!!!!Above Added: Tue May 7, 2013, 6:11 pm ESTs-10 pulling truck, hydrolic lift body, seat is in the middle, can enter threw doors , bed cover, heavy duty trans with blow proof bellhousing,msd,alum raditor 359 Cu. In. SBC.(400 DESTROKED) Dynoed 730 HP. @ 10,000 RPM. Dart little M block, 4.185 Bore. Bryant 3.268 stroke 30# crankshaft. 6.200 lite-weight Carrillo rods. JE FSR pistons. JE 1mm 1mm 3mm rings. 18 degree GM cast iron heads. 2.125 titanium intake valves. 1.6 titanium valves. CV Products titanium keepers & retainers Comp valve springs. Crower barless roller lifters. Special GM hi-RPM intake built by NASCAR team Electric water pump. SFI Balancer. MSD super tall deck Dist. jesel belt drive. Sheet Alum. valve covers. shaft rockers. motor turns 9000-10,000 rpm MIGHT SELL AS ROLLER OR SELL ENGINE SEPERATELY!!!! HIT ME UP WITH ALL OFFERS,CASH OR TRADE!!! IF YOU GOT ANY QUESTIONS EMAIL ME TRADERGRAHAM69@WINDSTREAM.NET OR CALL (270)317-1905 THANK YOU, DAVIDTractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/2814390/82-s-10-pulling-truck-t-k-OR-rolling.htmlWed, 19 Jun 2013 11:12:04 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Haulers/181747011/1999-Freightliner-Tractor-612-489-Miles.htmlThis is a 1999 Freightliner tractor that was used by one of todays top NASCAR team, Truck is very clean and has 612,489 miles on it and still has alot of life left. This truck can hold up to 300 gallons of diesel fuel. Listed below are some specs of this vehicle, if you have any questions please feel free to call us at 1-877-604-8077. Engine: Detroit Diesel 60 Series Engine Brake: Yes Sleeper: Standard Suspension: Air Ride Axles: Tandem Serial Number: 1FUYSSEB4YLG64374 5th Wheel: Airslide Front Wheels: Aluminum Rear Wheels: Aluminum Wheel Base: 220" Tire Size: 11R22.5 Frame: Steel Interior: Standard Fairings: None A/C: Yes Power Steering: Yes Color: Blue Tank Capacity: 300 Gallons (150 Per Side) Odometer: 612,489 Miles Additional Items Tilt/Telescopic Wheel Wrap Around Dash Cruise Control After Market Stereo Tractor and Truck Pullinghttp://www.racingjunk.com/Haulers/181747011/1999-Freightliner-Tractor-612-489-Miles.htmlWed, 19 Jun 2013 09:14:28 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181870387/KOOK-S-HEADERS-FOR-SONNYS-5-BORE-HEMI-E.htmlNICE CLEAN USED VERY FEW TIMES. KOOK'S BRAND(www.kooksheaders.com/). SEE PICTURES FOR MEASUREMENTS OF PIPES AND ETC. THEY HAVE EGT FITTINGS AND FITTING IN COLLECTORS. ASK FOR MARKTractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181870387/KOOK-S-HEADERS-FOR-SONNYS-5-BORE-HEMI-E.htmlWed, 19 Jun 2013 08:43:31 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/2928285/BBF-518-CU.IN.-high-torque-Stroker-engine.htmlthis is the mudslinger 518. Its HIGH TORQUE,relitivly mild rpm engine thats perfectly suited to pulling classes that still have run cast iron heads.mudslinger features cnc ported RHS Cast iron aftermarket heads[375/250cfm],714 lift roller cam,harland sharp shaft rocker system,4340 forged steel crank,H-beam 4340 steel rods,diamond 14-1 pistons,trick flow intake[ported] and holley black HP 950 carb.it was dyno tested 724@6000 rpm and 684tq.@4500 rpm.and was originally built for the Antique hot rod V-8 class[6000 rpm limit] but will work equally as well for truck pulling.go to foxlakeracing.com or youtube mudslinger 518 for more info. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/2928285/BBF-518-CU.IN.-high-torque-Stroker-engine.htmlSat, 15 Jun 2013 11:12:44 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/2120071/DataMaxx-Data-Logger-Tractor-Pulling-w-Dash.htmlThe DataMaxx Sportsman Kit is designed to maintain a consistent tune up and maximize your consistency. A must have for any multi-day racers or racer that is ready to take their bracket racing to the next level. This kit comes with dual oxygen sensor to ensure your tune-up is consistent each round and each race allowing you to be more consistent than ever. Comes with the DataMaxx LCD Dash, Engine RPM, Driveshaft RPM, Fuel psi, Oil psi, Dual Oxygen Sensors, Battery Voltage and 2 Switch Monitors. You can also get the Sportsman Kit if you would like the kit without the digital dash. Also check out the Bracket w/Dash Kit for a less expensive option and the Professional w/Dash Kit for 8 EGT probes. About The DataMaxx Data Logger The DataMaxx data logger is a complete stand-alone data acquisition system designed to fit the sportsman racer's budget, but with features and sample rates that rival the most expensive systems available. When it comes to a data logger, it's hard to tell one apart from another besides just looking at the price and a plethora of features list. Typically there are three main things you need to look at when choosing a data logger; Hardware, Software and Technical Support. The Hardware is the backbone of a data logger and has to be reliable if you're going to be happy with it. There is nothing more frustrating than spending hours assembling a data logger only to find that the first tire shake you have causes it to break. Using the latest technology is also key, and the DataMaxx utilizes an SD card for quick and easy data transfer as well as a modular CAN Bus system to transfer data between different expansion modules. This means that you can purchase the base main module at a low price, which has the room for 4 rpm's, 4 analogs and 2 switches. If you fill up your 4 analog channels and want to add more, you simply purchase an Expansion Analog Module and never have to send anything back to us or have to step up to a completely different unit. This means that you are only paying for you what you need and can expand the system anytime your needs change. The Software and its user friendly features are what makes or breaks a data logging system. After the hardware is installed you rarely need to think about it, but you will be using the software on a regular basis and if it's not easy to use and easy to understand, then it's a waste of money. At Computech we have put an extreme emphasis on making our software the easiest to use in the industry. We have made downloading and organizing your runs into events as easy as possible. We have made custom views that allow you to compare your RPM's to temps/pressures/accessories. Our "All In One" view allows you to see all of your graphs inside one big graph zone, but takes it a step further and allows you to choose whether you want it graphed at the bottom, top or middle. This allows you to view all of your channels at once without having a lot of overlapping lines, maximizing the amount of data you are able to understand. Combine that with easy to use run overlaying, channel highlighting, editing and run notes and you have the most powerful and easy to use piece of software on the market. The Technical Support should be one of your biggest factors when deciding on purchasing a data acquisition system. Because unless you are a professional tuner you will have questions and you will get confused from time to time. At Computech we understand that for a first time user this experience can be a little overwhelming and because of that we offer 24/7 evening and weekend customer support. We strive to have great customer support and searching on many racing forums will help reinforce that. We are all about the customer and we understand that we work for you, unlike the mindset of many of our competitors. Day or night, evenings or weekends we are here to answer any little question you may have. We also have an extensive online Data Logger Support section that allows you to read articles, download software, troubleshoot, ask questions, and watch video tutorials. Features •Sensors ◦Engine RPM ◦Driveshaft RPM ◦Fuel psi ◦Oil psi ◦Dual Oxygen Sensors •DataMaxx Main Module ◦Billet Aluminum Enclosure ◦100 Samples Per Second Per Channel ◦5 CAN Bus Connections ◦4 RPM Channels, Magneto Compatible ◦2 Switch Input Channels ◦2 Warning Light Outputs ◦4 Analog Channels ◦Battery Voltage Channel •DataMaxx LCD Dash ◦10 Channels Per Screen ◦Unlimited Screen Configurations ◦Customizable Shift & Warning Lights ◦SD Memory Card Port ◦Variable Speed Playback ■1/10x, 1/4x, 1/2x, 1x, 2x, 4x, 10x 100x ◦Single Cable connection ◦Billet Aluminum Anodized Enclosure ◦Day/Night Brightness Modes ◦Eliminates Need For Conventional Gauges •DataMaxx PC Analysis Software •2x 2Gb SD Memory Card •Remote Record Switch •Labels and Shrink Tube •Computech Screwdriver Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/2120071/DataMaxx-Data-Logger-Tractor-Pulling-w-Dash.htmlFri, 14 Jun 2013 16:20:57 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181862766/AED-Competition-Dominator.htmlAED Competition pulling series dominators are designed specifically for your application and pulling class. We custom design carbs to provide maximum power and torque while maintaining drivability. Bolt on an AED Competition dominator and see why AED has more Carb Shootout wins than all the others combined.Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181862766/AED-Competition-Dominator.htmlWed, 12 Jun 2013 13:40:24 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/2557753/Rockwell-20145-106-Hybrid-Housing.htmlPlease note that this is a 20145 housing with 106 spindles. Our fabricated 106 housings at the 77 3/4" standard width weigh approximately 75 lbs.Above Added: Thu July 26, 2012, 6:30 pm ESTThis is our newest creation for the pulling world. If you have a lot of power but need to lose some weight, take a look at this new housing. With it's large 15.25" ring gear and factory aluminum center section the Rockwell 20145 is sure to be the next big thing in truck pulling. The "turtle shell" is all chromolly, while the face plate is 1/2" A36 structural steel. It comes standard with chromolly back and bottom braces, large aluminum fill cap, drain bung, vent, and new billet 106 floater spindles. Housing pictured measures approx 82" from tip to tip, and weighed 113 lbs. Each housing is made to order and can be made to any length. Custom mounting brackets available on request.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/2557753/Rockwell-20145-106-Hybrid-Housing.htmlTue, 11 Jun 2013 08:13:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181852676/-NEW-ROCKWELL-H170-7-17-RATIO-RING-PIN.htmlASK FOR ADAM. Above Added: Tue June 4, 2013, 8:16 am ESTBRAND NEW OEM ROCKWELL H170 7:17 RATIO RING AND PINION SET. HAS 6 PINION TEETH X 43 RING GEAR TEETH. PART# A36950-3. INCLUDES PINION PILOT BEARING(ROLLER BEARING) AND PINION NUT. PINION# 36951, RING GEAR# 36950.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181852676/-NEW-ROCKWELL-H170-7-17-RATIO-RING-PIN.htmlTue, 04 Jun 2013 08:13:15 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Tires/181714226/BRUENS-PULLING-TIRES-INC..htmlNEW EMAIL BRUENS4@GMAIL.COMAbove Added: Thu April 4, 2013, 2:22 pm ESTDEALER FOR DICK CEPEK,NICHOLS AND PIT BULL PULLING TIRES.WE CARRY ALL SIZES.WE BUY SELL&TRADE PULLING TIRES&WHEELS.WE ALSO SELL THE STS TRXUS TIRES,CALL FOR PRICES 217-304-2312 OR EMAIL DAVIDBRUENS@GMAIL.COM THANKSTractor and Truck Pullinghttp://www.racingjunk.com/Tires/181714226/BRUENS-PULLING-TIRES-INC..htmlFri, 31 May 2013 19:53:38 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181846954/DANA-80-FULL-SPOOL-RING-PINION-BEARIN.htmlUPGRADE YOUR DANA 80 REAREND WITH A 35 OR 37 SPLINE FULL SPOOL, NEW RING & PINION(MANY RATIOS), AXLE SHAFTS, BEARING KIT. CALL ADAM FOR DETAILS.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181846954/DANA-80-FULL-SPOOL-RING-PINION-BEARIN.htmlThu, 30 May 2013 08:59:35 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181846945/GM-DODGE-11.5-REAREND-AXLE-POSI-UPGRAD.htmlUPGRADE YOUR GM OR DODGE 11.5" REAR DIFF TO BIGGER STRONGER 38SPL AXLE SHAFTS AND LOCKER, R&P'S(MANY RATIO'S) BEARING KIT. PARTS ARE AVAILABLE AS A KIT OR AS SEPERATE PARTS. WE ALSO HAVE A SPINDLE BORING TOOL WE RENT TO ALLOW FOR THE LARGER AXLE TO PASS THROUGH THE SPINDLE END. CALL ADAM FOR PRICING AND DETAILS.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181846945/GM-DODGE-11.5-REAREND-AXLE-POSI-UPGRAD.htmlThu, 30 May 2013 08:48:45 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181846042/99-02-DODGE-3-4T-SRW-DANA-80-REAREND-HOUSING.htmlALSO HAVE 2001-2002 DODGE 3/4T SRW DANA 80 DISK BRAKE EMPTY HOUSING AVAILABLE ALSO. Above Added: Tue June 4, 2013, 7:54 am ESTNEW DANA 80 EMPTY HOUSING. FROM 1999-2000 DODGE 3/4 TON SRW 4X2 APPLICATION. DRUM BRAKE STYLE. MEASUREMENTS(DONE OVER THE PUMPKIN) AS FOLLOW: * SPINDLE END TO END- 75.75" * PACKING PLATE FLANGE TO FLANGE - 61.5" * CENTER OF SPRING TO SPRING - 44" * CENTER OF SHOCK TO SHOCK - 31" UNIT HAD 4:10 RATIO INSTALLED IN IT. THEY ARE SOLD EMPTY - NO GUTS. SHIPPING IS ADDITIONAL. ASK FOR ADAM Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181846042/99-02-DODGE-3-4T-SRW-DANA-80-REAREND-HOUSING.htmlWed, 29 May 2013 14:12:08 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181845937/NEW-ROCKWELL-F106-SQHD-20145-RING-PIN.htmlNEW PARTS IN STOCK FOR ROCKWELL F106, SQHD, 20145 DIFF’S. RING & PINION’S (MANY RATIO’S), BEARING KIT’S, BOLT KIT’S, BILLET PINION SUPPORT’S FOR THE F106 REAR’S. MORE ON HAND FOR OTHER APPLICATION’S AS WELL. COMPLETE 3RD MEMBER BUILD’S AVAILABLE. CALL FOR PRICE AND AVAILABLITY, ASK FOR ADAMTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181845937/NEW-ROCKWELL-F106-SQHD-20145-RING-PIN.htmlWed, 29 May 2013 13:02:25 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181845905/DODGE-DANA-60-DISCONNECT-CONVERSION-AXLES.htmlNew Dodge Dana 60 front disconnect conversion axle and cover. Parts available to fit 1994-1998 Dodge Dana 60 fronts with 30 spline internal gears, 1999-2002 Dodge Dana 60 front diffs with 32 spline internal gears. Also 35spl kits to fit all application 1994-2002. 4340 material inner axle shafts to remove the multiple piece disconnect axle, fork and collar assembly to a one piece axle. Also an aluminum cover with vent pipe is available to replace the vacuum fork housing Assembly. axles have seal surfaces to fit stock seal areas in the housings. there basically a direct fit and uses your stock u-joint and outer stubs. just verify the year and spline count on your differential. Call and ask for Adam.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181845905/DODGE-DANA-60-DISCONNECT-CONVERSION-AXLES.htmlWed, 29 May 2013 12:38:24 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181845902/MCLEOD-TWIN-DISK-PULLER-CLUTCH-FLYWHEEL-KIT.html**NEW** MCLEOD TWIN DISK PULLER CLUTCH. KITS HAVE: W/SINDERED IRON DISKS 1 1/8" OR 1 3/8" X 10SPL. PRESSURE PLATE W/BRONZE HEAT SHEILD. FLYWHEEL 168T NUETRAL BALANCED FOR BBC. FLOATER, STANDS & SHIM KIT. MCLEOD KIT PART #'S AVAILABLE 4402-00-04 OR 4402-00-06. CALL MCLEOD FOR ANY APPLICATION QUESTIONS AT 1-714-630-2764. KITS ARE IN STOCK, ASK FOR ADAM. SHIPPING COST ADDITIONALTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181845902/MCLEOD-TWIN-DISK-PULLER-CLUTCH-FLYWHEEL-KIT.htmlWed, 29 May 2013 12:35:46 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181735699/PROFAB-F106-SQHD-BILLET-1480-1550-YOKES.htmlBRAND NEW BILLET 1480 OR 1550 SERIES U-JOINT YOKE. FITS PROFAB T-CASE OUTPUT SHAFTS AND SQHD PINION SHAFTS*. 1.75" X 10SPL. YOKE WAS DESIGNED FOR A U-BOLT STYLE HOLD DOWN(U-BOLT KIT SOLD SEPARATELY). *WE HAVE SEALS TO ADAPT THE YOKE TO EITHER APPLICATION, CALL FOR MORE DETAILS. ALSO HAVE BILLET 1480 SERIES PINION YOKES FOR THE F106 ROCKWELL REARENDS(1.5" X 10SPL). FOR FOR PRICING. ASK FOR ADAMTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181735699/PROFAB-F106-SQHD-BILLET-1480-1550-YOKES.htmlWed, 29 May 2013 12:00:56 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181735706/77-91-GM-DRW-DANA-60-FRONT-DIFF-USED-COMPLETE.htmlask for Adam.Above Added: Wed May 29, 2013, 12:42 pm ESTUSED DANA 60 FRONT DIFF. 4:10 RATIO DRW. 77-91 GM APPS. USED TAKE-OUT DIFF. SHIPPING AVAILABLE AT ADDITIONAL COST. Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181735706/77-91-GM-DRW-DANA-60-FRONT-DIFF-USED-COMPLETE.htmlWed, 29 May 2013 12:00:56 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181845661/Sportsman-Mini-Modified-Chassis-Kit.htmlSportsman Mini Modified Tractor Kit, Includes: 1- Right side Sportsman Mini Modified Frame rail 1- Left side Sportsman Mini Modified Frame rail 1- Sportsman Front Plate 1- Pair of Weld on Tractor Skis 1- Front Tow Hitch w/ brackets 1- Pair of Soft Touch Wheelie Bars 1- Brake Pedal Assembly (Doesn't Include Master Cylinders) 1- Long Tie Rod for 8" Rack 1- Short Tie Rod for 8" Rack 1- Thin Line 8" Rack & Pinion 1- Rack & Pinion Coupler 1- Sportsman Draw Bar Mild Steel 2- Master Cylinder Mounting Brackets 1- Sportsman Tractor Spindles, Left side 1- Sportsman Tractor Spindles, Right side xProductThumbnail('productid=24167030'); Sportsman Mini Modified Tractor Kit $0.00 PriceSportsman Mini Modified Tractor Kit (+$1,999.99)xAddToBag('productid=24167030'); Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181845661/Sportsman-Mini-Modified-Chassis-Kit.htmlWed, 29 May 2013 08:24:17 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181844882/-427-discount-on-Logger-Dash-for-Pulling.htmlIndividual pieces total $2526, Package deal is $2099 SAVE $427 Create graphs on your laptop to analyze, print and e-mail. Monitors: - Engine RPM - Shaft RPM - 2 axle RPM's - Throttle Position - MPH via GPS Includes - Digital Dash - USM module - Lienar sensor for Throttle Position - 3 shaft speed sensors and magnets - cables - software - 100% complete Additional cost module usually required to pick up diesel RPM. Easily add 8 EGT's, fuel pressure, boost etc with plug & play sensors. Contact Greg 609-265-2110 email: gkelley@motorsportsinnovations.com Order online 24/7 http://www.motorsportsinnovations.com/RacePak/racepak-pulling.html Purchase on my Ebay store that has over 4800 100% positive ratings http://stores.ebay.com/Motor-Sports-Innovations International orders - We ship worldwide 3-4 days per week. Usually USPS or UPS but will use others. - We accept international credit cards, PayPal and wire transfers.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181844882/-427-discount-on-Logger-Dash-for-Pulling.htmlTue, 28 May 2013 16:06:01 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181842560/8-EGT-Racepak-data-logger-for-pulling.htmlIf you are pulling this is the data logger you need. It includes: - G2X recorder (which has RPM, GPS speed and volts (Diesel RPM pickup may require extra sensors/cost)) - 8 EGT's (which includes weld bungs) - Cables, software, laptop accessories - PLUG & PLAY You will get a log on you laptop showing the engine RPM, g force and the 8 EGT's laid out on a time line so you will KNOW how the pull went. Add a throttle position sensor and know exactly where on the pull you were able to go full throttle. Overlay pulls to see differences. Motorsports Innovations - large stock, tech support help, from a guy who actively races and supports many area racing associations. Easily ass throttle position, shaft speeds, pressures etc. All popular Vnet sensors & dash kits in stock. Sensors in stock - With V-net module Fuel Pressure High or Low .......................... $250 Oil pressure ........................................... $250 Water or Oil temp ...................................... $170 IR tire/track temp ..................................... $325 Trans temp ............................................. $170 Boost or Trans Pressure.............................. $250 FREE US ground shipping Contact Greg 609-265-2110 Email : gkelley@motorsportsinnovations.com Order online 24/7 http://www.motorsportsinnovations.com/RacePak/racepak-pulling.html Purchase on my Ebay store that has over 4700 positive ratings http://stores.ebay.com/Motor-Sports-Innovations International orders - We ship worldwide 3-4 days per week- USPS or UPS. - We accept international credit cards, PayPal and wire transfers.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181842560/8-EGT-Racepak-data-logger-for-pulling.htmlSun, 26 May 2013 19:58:04 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181842484/475-Big-Block-Chevy-Motor.htmlI'm selling this 475 BB chevy complete turn key carb to pan. includes headers. includes flywheel with dual disk mccloud clutch with crower clutch disks. It only has 15 hooks on it. Custom built by Pfeiffers engine specialties. This motor was in an altered stock Illini State Pullers class and was very competitive. Headers that are included are fender well exit, jet hot coated, 2 1/4 inch primaries. Engine specs: CP custom pistons and rings- gas ported and pin fit scat 4340 crank callies compstar "I" beam rods with L19 bolts comp cam custom roller cam jesel rocker shafts smith brothers push rods comp cam roller lifters msd crank trigger hei balancer dart iron eagle BB heads fully ported (titanium valves, keepers, and locks) super victor intake manifold pro systems dominator carburetor moroso 4 vane vacuum pump comp cam belt drive system compression ratio 15:1 SERIOUS INQUIRIES ONLY, more details about motor available upon request. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181842484/475-Big-Block-Chevy-Motor.htmlTue, 18 Jun 2013 21:01:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181842459/Custom-Built-C103-rear-axles.htmlI am selling 2 rockwell C103 rear axles. One has custom built SCS axles and drive plates. Custom built aluminum hubs with 106 bolt pattern. welded carrier with 5.29 gear ratio. hub to hub is 68 inches. 1480 yolk. The second one has a welded carrier with 5.29 gear ratio. set up for 8 bolt rims and comes with 6 bolt aluminum adaptors. 2 sets of stock axles and an extra bare 3rd member. will deliver for $1.00 per mile. Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181842459/Custom-Built-C103-rear-axles.htmlTue, 18 Jun 2013 21:01:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Tires/181842472/Dick-Cepek-FC-II.htmlI am selling a set of 315-75-16 Dick Cepek FC II. Tires are siped with only 20 passes. Like new. Tractor and Truck Pullinghttp://www.racingjunk.com/Tires/181842472/Dick-Cepek-FC-II.htmlTue, 18 Jun 2013 21:01:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181867872/648-CID-Ford-Hemi-Nearly-1500HP-Fresh-.html648 CID Ford Hemi,Nearly 1500HP, Fresh Alcohol Injected 39500.00 or best offer New eliminator block Bryant Crank RDI Ford Hemi Heads Titanium valves and latest updates Moroso Chromed Aluminum valve covers New 60mm CAM New .904 Isky Lifters Steffs Dry sump oil pan Avaid 5 stage oil pump New GRP Aluminum rods Danny Bee Belt w/new belt New MSD Crank trigger New distributor & wires HRC Sheet metal intake w/Dual Enderle Throttle Bodies Alcohol injected dual nozzle set-up w/down nozzle under valve cover Waterman Fuel pump-direct cam driven Moroso enhanced vacuum pump Zero runs on motor,(other than DYNO) New Block,rods,pistons,rings,bearings,valve springs,valve job,crank trigger,distributor&wires This motor makes great horsepower and torque. We have dyno sheets for the serious buyer. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181867872/648-CID-Ford-Hemi-Nearly-1500HP-Fresh-.htmlMon, 17 Jun 2013 10:05:42 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181863990/648-CID-Ford-Hemi-Nearly-1500HP-Fresh-.html648 CID Ford Hemi,Nearly 1500HP, Fresh Alcohol Injected 39500.00 or best offer New eliminator block Bryant Crank RDI Ford Hemi Heads Titanium valves and latest updates Moroso Chromed Aluminum valve covers New 60mm CAM New .904 Isky Lifters Steffs Dry sump oil pan Avaid 5 stage oil pump New GRP Aluminum rods Danny Bee Belt w/new belt New MSD Crank trigger New distributor & wires HRC Sheet metal intake w/Dual Enderle Throttle Bodies Alcohol injected dual nozzle set-up w/down nozzle under valve cover Waterman Fuel pump-direct cam driven Moroso enhanced vacuum pump Zero runs on motor,(other than DYNO) New Block,rods,pistons,rings,bearings,valve springs,valve job,crank trigger,distributor&wires This motor makes great horsepower and torque. We have dyno sheets for the serious buyer. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181863990/648-CID-Ford-Hemi-Nearly-1500HP-Fresh-.htmlThu, 13 Jun 2013 15:34:15 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Gear/181862997/NEW-SPICER-DANA-60-PARTS-1.5-35-SPLIN.htmlNEW SPICER OEM 1-1/2" 35 SPLINE DANA 60/70 OUTER AXLE STUBS 12" LONG (MEASURED CENTER OF JOINT TO END OF AXLE) $90.00 EACH (INCLUDES 1-1/2" SNAP RING) NEW SPICER OEM 35 SPLINE DRIVE FLANGES / PUCKS FOR DANA 60 FRONT WITH 1-1/2" 35 SPLINE OUTER AXLES $100.00 EACH NEW SPICER OEM HUB CAPS FOR DANA 60 HUB CAPS OFF THE END OF THE HUB WHEN DRIVE FLANGE IS USED $10.00 EACH NEW SPICER OEM DIRT SLINGERS (FOR OUTER AXLE STUB) $5.00 EACH NEW SPICER OEM DANA 60 INNER AXLES SHORT SIDE – $115.00 OBO LONG SIDE - $140.00 OBO NEW SPICER SOLID CROSS U-JOINTS (NO GREASE FITTING) DANA 60 FRONT - $50.00 1410 SERIES - $33.00 ORIGINAL ROCKWELL COTTER PINS FOR F106, C103, ETC CARRIER SIDE BEARING NUTS $2.00 EACH NEW SPICER END YOKE PART # 3-4-2161-1 FOR 1410 SERIES U-JOINT 2"–10 SPLINE (MEASURES 1.970" MAJOR / 1.696" MINOR) LENGTH THROUGH BORE (LTB) = 1.875" OVERALL HEIGHT (OAH) = 3.750" SEAL DIAMETER = 2.625" (MEASURES 2.597") APPLICATION: GM H150 – 170 – 185, ETC INCLUDES STRAP KIT $75.00 OBO I AM AN AUTHORIZED DISTRIBUTOR FOR BRAD PENN RACING / HIGH PERFORMANCE OILS - "THE GREEN OIL" - FOR AUTOMOTIVE AND MOTORCYCLES. THIS IS THE KING OF PERFORMANCE ENGINE OILS. FORMERLY KENDALL GT-1, IT IS 100% MADE IN USA FROM THE BEST CRUDE ON EARTH AT THE FORMER KENDALL REFINERY IN BRADFORD, PENNSYLVANIA, THE OLDEST WORKING REFINERY IN THE WORLD. IT CONTAINS THE HIGHER LEVELS OF ZINC-PHOSPHORUS (ZDDP) WHICH IS REQUIRED IN ALL PERFORMANCE ENGINES, ESPECIALLY THOSE WITH FLAT-TAPPET CAMS. VISIT WWW.PENNGRADE1.COM FOR MORE INFO. MIKE CELL 414-418-4591Tractor and Truck Pullinghttp://www.racingjunk.com/Gear/181862997/NEW-SPICER-DANA-60-PARTS-1.5-35-SPLIN.htmlWed, 12 Jun 2013 17:39:52 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181862376/For-any-of-your-SCS-Rearend-needs-call.htmlI sell all SCS parts,so call or message me for your needs. Selling sheetmetal housings and aluminum third members,and bell housings also.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181862376/For-any-of-your-SCS-Rearend-needs-call.htmlWed, 12 Jun 2013 07:57:12 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/2875401/1979-F250-Pull-Truck.htmlHas a new 460. 811 Horsepower motor. Has many extra parts. I have pulled 8 times with new motor & never lost. I have all paperwork on new motor. $25,000 912/334-2069Above Added: Tue June 11, 2013, 11:20 am ESTHas new 460. 811 horsepower motor. Has many extra parts. I have pulled 8 times with new motor and never lost. I have all paperwork on new motor. $30,000 912. 334- 2069Above Added: Sat February 23, 2013, 10:46 pm ESTHas new 460. 811 horsepower motor. Has many extra parts. I have pulled 8 times with new motor and never lost. I have all paperwork on new motor. $40,000 O.B.O. CALL. 912-334-2069Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/2875401/1979-F250-Pull-Truck.htmlMon, 10 Jun 2013 20:10:23 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181797716/Pulling-truck.html1987 pulling truck. Bud lightTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181797716/Pulling-truck.htmlMon, 10 Jun 2013 03:45:11 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181858006/mid-80-s-super-mod-2wd..htmlhad 6 offers, your getting better.Above Added: Tue June 18, 2013, 5:48 pm ESTthis truck comes with what you see, we pulled the motor and trany out of it in 1998, been sitting ever since, Above Added: Sat June 15, 2013, 12:17 pm ESTtube chassis, jd skidder. aluminum wheels, spicer overdrive box, 26.7 and 21.3 finals, setup for blown bigblock, auto, Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181858006/mid-80-s-super-mod-2wd..htmlSat, 08 Jun 2013 23:28:38 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181856396/496-bbc-871-alc-blown.html496 bbc 871 little field hat to pan fuel pump to fly wheel call for more info 321-689-0332 ran 20lbs at 1400 hp also fti tranny 3000.00Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181856396/496-bbc-871-alc-blown.htmlFri, 07 Jun 2013 11:50:45 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181855207/SMFWD-S-10-Turn-Key-or-Roller.htmlBlown Super Mod. 4wd for sale complete (turn-key) or as complete roller. Basic Info: - 133 in wheelbase custom built square tube chassis. - Adjustable weight box and coil spring front suspension - Pro-fab quick change transfer case - Power steering - Performance pros hubs/ wilwood breaks - turbo 400 transmission - 496 c.i. Blown BBC - Wired for MSD ignition - 8gal. chrome stainless fuel tank - Real alum. wheels all around - Deep cut new style cepeks on rear - New style cepek fronts (never cut/ used for 3 indoor hooks) For additional pics and information feel free to call or email. ThanksTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181855207/SMFWD-S-10-Turn-Key-or-Roller.htmlThu, 06 Jun 2013 11:45:25 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Ignition-Systems/181854136/Billet-Ignition-Kill-Switch.htmlBillet Aluminum kill switches with welded stainless pin and D-Ring. These have the highest amp rated switches on the market. With a rating of 35 amps. most kill switches on the market have a small 10 amp rated switch. This setup is a "completed circuit" with the Pin installed, and "Stops the Circuit" when the Pin is Pulled. it also has a pass-threw hole for a ziptie to loop thru the D-Ring to the Billet body for added assurance for the pin to stay put. Has a single 5/16 bolt hole for mounting to your vehicle. other setups like these are going for $130+... We have these for $80 plus $10 shipping to anywhere in the U.S. Give us a call today @ 660-882-8468 Thanks! Tractor and Truck Pullinghttp://www.racingjunk.com/Ignition-Systems/181854136/Billet-Ignition-Kill-Switch.htmlWed, 05 Jun 2013 14:50:47 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181847055/1962-CHEVROLET-BEL-AIR-2-WHEEL-DRIVE-PULLER.htmlON EBAY NOW ITEM #261225215027!!!!Above Added: Sun June 2, 2013, 9:10 pm EST1962 Chevrolet Bel Air 2 wheel drive puller. Has all steel body, and custom steel chassis. Windows all roll up and down, windshield is cracked tho. Weighs about 5000lbs. by itself, but pulls in the #6500 2 wheel drive truck class. Has adjustable primary hitch and a secondary safety hitch, wheelie bars, safety kill switch, and back up lights. Has water and oil gauges, 2 bucket seats, aluminum radiator, 2 batteries, aluminum fuel cell, electric fans, aluminum electric waterpump, all four aluminum wheels, Dick Cepek Giant Puller tires in rear, 2 speed eaton rearend, 4speed GM tranny, blowproof bellhousing, and Triple disc crowerglide automatic clutch. The engine is a FRESH 462CI Big Block Chevy with Enderle alcohol injection, 80A fuel pump, shut off valve, Rectangular port steel heads with lots of porting and polishing, solid roller cam and lifters, aluminum roller rocker arms, Unilite distributor, 6A MSD box, Mallory coil, 12.5/1 dome pistons, steel H-beam rods, steel crank, gear drive, aluminum mini starter, and chrome valve covers. $14,000 for it all trun key. Or $6500 for complete roller, (minus engine, msd box, and fuel cell). Also have fuel jugs and barrels, 20-25 gallons of alcohol, 1500#'s of suitcase weights, misc. parts and tools that can go with it for an extra $1000. Call 1-417-621-1841 for more info.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181847055/1962-CHEVROLET-BEL-AIR-2-WHEEL-DRIVE-PULLER.htmlThu, 30 May 2013 11:10:49 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Gear/181845628/PRO-FAB-GEARS.htmlI HAVE A 800 AND 900 PROFAB GEAR FOR SALE. I WILL SELL THE SET FOR 150$Tractor and Truck Pullinghttp://www.racingjunk.com/Gear/181845628/PRO-FAB-GEARS.htmlWed, 29 May 2013 07:46:59 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181844494/1100-HP-Modified-Pulling-Tractor.htmlEconomy Modified Pulling tractor with Steve Vance Ford Prostock Racing Engine. A500 block sleeved to 482 cubic inches, Ford Racing E heads with extensive work, Pro Fab upright headers, Barry Grant carb and fuel system on racing gas, custom sheet metal intake, MSD front belt drive distributor and digital 7 electronics, Jessel rockers coupled to a built C6 automatic. Powercoated tube chassis with narrowed and lightened Cockshutt 40 rear. Mid West aluminum wheels with Wilson cut 18.4 SAT Firestone radials. Turnkey or will consider splitting engine and chassis. Buddy Woodson, Eagleville Tn.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181844494/1100-HP-Modified-Pulling-Tractor.htmlTue, 28 May 2013 10:22:36 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181841964/CLUTCHES-BELLHOUSINGS-AND-MORE.htmlSFI CERTIFIED 10 1/2 or 11 inch pressure plates 10 1/2 and 11 inch disc and floaters stands shims and whole clutch set ups HYD CLUTCH PEDAL KIT INCLUDES PEDAL MASTER CYL LINE AND SLAVE CYL Bellhousings BROWELL,PROBELL,LAKEWOOD ALSO STOCK DEPTH FORD 460 SFI BELLHOUSINGS DANA 60 POWER LOK UNITS 14 BOLT SPOOLS MASTER INSTALL KITS ARB AIR LOCKERS PROFAB KITS OR COMPLETE TRANS BUILT ADAPTER TO MATE SM465 TO YOUR MARRIED FORD NP205 MACHINED BEARING BRONZE FOR 14 BOLT REAR PINION BEARING MACHINED TRANFER CASE BEARING RETAINERS AND MUCH MORE email travs4x4@yahoo.com or call 859-991-4996 Travis if no answer be sure to leave a message Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181841964/CLUTCHES-BELLHOUSINGS-AND-MORE.htmlSun, 26 May 2013 08:43:30 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181839611/8mm-blower-pulleys.htmlI have 57 59 60 65 67 tooth pulleys 8 mm Kevin 802-363-8841Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181839611/8mm-blower-pulleys.htmlThu, 23 May 2013 21:21:10 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181835691/2WD-Turn-Key-Ready.htmlThree time points champion pull truck 2x4 super stock 383 stroker ram slipper clutch, 4spd, msd ignition, 35 inch boggers, hyd tilt bed, tilt nose all weights needed to make 6200lb call Kim @ 207-660-2181 call for detailsTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181835691/2WD-Turn-Key-Ready.htmlMon, 20 May 2013 13:06:51 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181870543/Modified-Chassis.htmlRolling Modified Tractor Chassis Wedge Frame 30.5" 10 ply Pullers on Steel Rims Lemke needled JD Skidder rearend NTPA certified rollcage 3 speed Banter gearbox Runs from 1 to 3 motors... Email for details, serious inquiries only Asking $7k or BO Located in SE Wisconsin flirtin@charter.net Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181870543/Modified-Chassis.htmlWed, 19 Jun 2013 10:50:20 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181870537/clutch-shaft.html1-3/8" 10 spline on input side, the output is 1-3/8" 16 spline. It is 11-3/8" overall length, the input splines are 3" long. The nub is .780 diameter. Bearing is good and very good shape overall, splines are clean. Asking $125 plus shipping. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181870537/clutch-shaft.htmlWed, 19 Jun 2013 10:48:10 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181870532/Multi-Engine-Gearbox.htmlMulti Engine Crossbox ProFab built Run 2-5 motors 1:1 ratio 36" input to input includes custom SFI blanket Email for details and photo to flirtin@charter.net or Call 262-719-0907 wisc Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181870532/Multi-Engine-Gearbox.htmlWed, 19 Jun 2013 10:46:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/2836599/Ford-Pro-Mod-4WD-with-705-Ford-Boss-Hemi.html1990 Ford GTS Body that lifts, DBR chasis,(built by Dan Bosh), SQHD rear axle built by TRB, 2 1/2 Ton military front, with Profab billet axles, alum hubs, with Pro-formance Pros lock-out. Pit-bull front tires, cepek rear tires, both on real wheels, Profab ultimate transfer case,transmission. Lakewood bellhousine with cross shaft,crower 3-disk clutch.705 cu.in. Ford Boss hemi, for motor info see ad # 2769487. This is a complete truck deal ready to run, strong runner and have been told by many people looks awesome. I will not sell truck seperate from motor has to sell together, or I will just sell motor alone as described in motor ad.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/2836599/Ford-Pro-Mod-4WD-with-705-Ford-Boss-Hemi.htmlWed, 19 Jun 2013 08:33:11 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/2170983/Complete-2-Wheel-Drive.html1935 Chevy Two Wheeler, 572 Rodeck, BacMan heads, 1471 blower, 3 speed Profab Transmission with Reverser. Solid drive shaft, Cepek tires. Well balanced and runs straight. 630-556-3573 evenings or email bbaie1@att.netTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/2170983/Complete-2-Wheel-Drive.htmlWed, 19 Jun 2013 03:45:14 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181868845/Turbine-Pulling-Tractor.htmlemail cumaclandscape@hotmail.comAbove Added: Mon June 17, 2013, 11:47 pm ESTT-53 Lycoming Turbine Engine power pulling tractor. Massey rear end Good Year double cut tires, SCS 30. Very unique tractor. Serious inquires only. Dont waste my time. Ready to go pulling.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181868845/Turbine-Pulling-Tractor.htmlMon, 17 Jun 2013 23:45:10 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Gear/181868706/Pro-Fab-and-Reverser.htmlPro Fab transfer case with 3 sets of gears and reverser transmission $2700 obo call or text only 931-200-6280 can send pic Tractor and Truck Pullinghttp://www.racingjunk.com/Gear/181868706/Pro-Fab-and-Reverser.htmlMon, 17 Jun 2013 20:55:29 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181868222/5.9-Cummins-engine.html5.9 Cummins engine. 2 fresh turbo chargers; Simpson water system; dry sump oil system; port and polished head; PDI header; billet cam; 120 injector lines; modified injectors; 14mm injector pump; PG150 fuel pump; billet air shut-off; solid block; set up for Chevrolet or Dodge flywheel and clutch; high temp pistons; fire rings Fresh motor. Has not been run since fresh. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181868222/5.9-Cummins-engine.htmlMon, 17 Jun 2013 14:17:48 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181867572/1945-DODGE-POWER-WAGON.html1945 DODGE POWER WAGON PRO MOD TRUCK ALUMINIUM BED 11,050 HP 640 Cu In TALL DECK 4 3/4 STROKE HILL-BORN INJECTION ROCK WELL REARENDS BIG BRODIX HEADSAbove Added: Tue June 18, 2013, 9:25 pm EST1945 DODGE POWER WAGON PRO MOD PULL TRUCK ALUMINIUM BED 11,050 HP 640 Cu IN TALL DECK 4 3/4 STOCK HILL-BORN INJECTION ROCK WELL REAR END Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181867572/1945-DODGE-POWER-WAGON.htmlMon, 17 Jun 2013 01:52:47 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181867501/CLASSIC-MO.htmlFOR SALE : 1951 44 MASSEY HARRIS CLASSIC MODIFIED THAT I BUILT AND CAMPAIGNED FOR THE PAST 9 YEARS, WON CHAMPIONSHIP TITLES AND TO MANY WINS TO COUNT...TRACTOR HAS A 358 INCH SBC, NEW HOLLEY DOMINATOR 1050, MSD 7AL2, DUAL DISC SLIPPER CLUTCH, PLUS MANY MORE HIGH QUALITY FEATURES AND THE BEST OF MAINTENCE, NO DOLLARS HAVE BEEN SPARED ON THIS CLASSIC ! FOR MORE INFORMATION ABOUT OR TO VIEW TRACTOR CALL MIKE OR MY WIFE JAMI AT NUMBERS LISTED, SERIOUS INQUIRYS ONLY PLEASE !!!Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181867501/CLASSIC-MO.htmlSun, 16 Jun 2013 23:14:56 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Wanted/181867450/Tires.htmlLooking for good set of 18-4 x 16-1 cepecksTractor and Truck Pullinghttp://www.racingjunk.com/Wanted/181867450/Tires.htmlSun, 16 Jun 2013 22:26:44 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Tires/181867064/pulling-tires.htmlMaxi-Trac pulling tires 24.5 32 9 lug steel wheels includedTractor and Truck Pullinghttp://www.racingjunk.com/Tires/181867064/pulling-tires.htmlSun, 16 Jun 2013 20:08:54 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181867052/Diamond-Pistons-for-Chevrolet-Big-Block.html4.560 bore. 4 inch stroke. Ordered wrong part - unable to return. Brand new, still in box.Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181867052/Diamond-Pistons-for-Chevrolet-Big-Block.htmlSun, 16 Jun 2013 16:10:25 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181867045/Semi-Pulling-Hitch.htmlSelling a Semi Pulling Hitch, I used it once and no longer have a need for it. The hitch is in great shape.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181867045/Semi-Pulling-Hitch.htmlSun, 16 Jun 2013 15:48:46 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181865970/1950-FWD-Pulling-Truck.htmlCurrently the points leader. 7 time points champ. All aluminum frame. Aluminum dashboard. Tonneau cover. Dick Cepeck giant pullers. All set up. Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181865970/1950-FWD-Pulling-Truck.htmlSat, 15 Jun 2013 13:34:12 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/2167429/Dodge-Cummins-Modified-Sled-Puller-2006.html-Ready for 2011 season. -Turn-Key -6.7L -Compound Chargers w/ incab controllable wastegate -28 ch. Wireless Data Logger -6pt Cage with 5 pt harness -Front Air Locker -Rear Spool -Call for more details.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/2167429/Dodge-Cummins-Modified-Sled-Puller-2006.htmlSat, 15 Jun 2013 03:45:09 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181863125/460-dove.htmlComplete from oil pan to carb all original 460 with dove c heads and dove a block, also have another block from a 79 ford f150 with extra odds and ends. All for 750.00 located in Papillion,Ne willing to meet as well within 250 miles. Call or text 402.510.67five0Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181863125/460-dove.htmlWed, 12 Jun 2013 20:05:48 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181863065/pulling-tractor.htmlI have a very nice Copar Panzer pulling tractor for sale. It has a Wisconsin twin cylinder motor in it, a Mikuni carburetor, a big thumping cam and a brand new battery. Its got a 50 Plymouth rear end and a 50 Plymouth 3 speed transmission. I'm including two aluminum rear rims with it (in the picture) has a wheelie bar on the back. I've won many pulls with it. Runs excellent! Call 937-336-4431 anytime. Also I may trade for a 4x4 truck no junk please. Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181863065/pulling-tractor.htmlWed, 12 Jun 2013 19:01:28 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Gear/181861938/Standard-rotation-SCS-drop-box.htmlPrice includes 2 1/2 ton flat flanges Call and place your order today and we can ship out the next day Price mat very depending on flange or yoke requested. shipping not included in price We accept Visa MasterCard and discover Gearheart's Garage & 4x4 Off-Road (419)989-0906 or Contact Jeremy at (419)606-6548 Mud truck Mega truck monster truck Pulling truck Rockwell Axles Rockwells Tractor and Truck Pullinghttp://www.racingjunk.com/Gear/181861938/Standard-rotation-SCS-drop-box.htmlTue, 11 Jun 2013 20:06:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181861111/ford-tug-o-war-truck.html1979 Ford four speed, set up for tug o war 4200lb class..has a 300 six cylinder. Beadlocks front and back. Truck won points last year with kytrucktuggers....15029021639Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181861111/ford-tug-o-war-truck.htmlTue, 11 Jun 2013 08:02:58 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181860799/Eagle-4.25-Lightweight-Steel-Crank.htmlBBC 4.25 Lightweight Steel Crank Pulling Truck Crank. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181860799/Eagle-4.25-Lightweight-Steel-Crank.htmlMon, 10 Jun 2013 22:23:30 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181859692/6200lb-FWD-98-Chevy-.html98 Chevy silver and black Above Added: Mon June 10, 2013, 10:27 am ESTChassis and body. 106 rear alum hubs . Military front alum hubs . Pitbulls rear Cepecks front. SCS Gearbox. Call for more info or pics.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181859692/6200lb-FWD-98-Chevy-.htmlMon, 10 Jun 2013 10:22:15 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181859384/Pro-stock-4wd.html98 body, 106 Rockwell rear, Dana 60 front with locker and new outer axels and joints. New rear gear and drive shaft. 620 gears. Msd 7al , quick fuel pump, water pump, water tank, fuel tank and oil tank with lines. Cepeks and real wheels. Pro fab trans and transfer case. Have 5 sets of gears.header and clutch, clutch has 8 hooks since rebuilt. Just needs engine. Saleing to go back to dirt track raceing.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181859384/Pro-stock-4wd.htmlMon, 10 Jun 2013 01:37:43 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181858328/Modified-Garden-Tractor.htmlHas 2.3L ford that has been worked. Just put ford 9in rear in last year with mosher axles. Its in on 31in Cepeks with aluminum rims. Asking $7000.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181858328/Modified-Garden-Tractor.htmlSun, 09 Jun 2013 09:28:39 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181857673/WANTED-3Spd-Pro-Fab-Twin-Countershaft-Trans-.htmlLooking for a 3spd Pro Fab Twin Countershaft Trans. I also need the drivetrain and alum. shielding! If you no of anything please contact me! (912) 213-1041 day or night Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181857673/WANTED-3Spd-Pro-Fab-Twin-Countershaft-Trans-.htmlSat, 08 Jun 2013 16:37:26 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181857423/Turn-Key-Mini-Mod.htmlThis is a turn key mini mod ready to go pulling. Has a sbc 383 motor, runs on gas, has a holly 750 carb. Turbo 350 trans with a ford 9inch rear end. Tractor has the advance chassis fenders and wings kit as also the roll cage is from advance chassis also. Tractor is all powder coated, very clean looking. Tractor is new for 2013 season only been down track twice. If you have questions email, call or text 703 297-9177 Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181857423/Turn-Key-Mini-Mod.htmlSat, 08 Jun 2013 10:58:56 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181857323/1986-dodge-ram-250-4x4.html1986 dodge 3/4 ton. Dana 60 rear. 44 front. Np435 trans with 208 t case. 360 motor runs strong. Class v Reese hitch. Nice 265/75/16 Firestone mt's on American racing wheels. Body has very little rust. Solid truck. Interior is clean. The seat it wore pretty bad. Gas gauge does not work. Runs and drives great. Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181857323/1986-dodge-ram-250-4x4.htmlSat, 08 Jun 2013 09:17:13 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181856284/1250-CFM-FX-4712-Quick-Fuel-Carburetor-.html1250 CFM FX-4712 Quick Fuel Carburetor For Sale: Came off of pulling truck motor built by Steve Schmidt Racing. It has 23 passes on it. Comes with spacer block. Please call 573-690-3703 or 573-437-2253 with any questions. Thanks.Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181856284/1250-CFM-FX-4712-Quick-Fuel-Carburetor-.htmlFri, 07 Jun 2013 09:58:10 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Haulers/181855091/Motivated-Seller-Make-Offer.htmlThe tractor is an 86 Kenworth updated by competition trailers in 1993, it is 320 inch wheelbase, living quarters in bunk, 120 inch bunk, 25 k generator, 60 gallon air compressor all mounted on back of tractor, the trailer is a 1993 competition, 53 ft., elevator door, hauled 2 complete funny cars upstairs, tow car or golf cart down, cabinets throughout, crew chief office, living quarters in the trailer. TEXT 4 1 9 8 8 9 0 7 1 0 Motivated Seller - $65,000Tractor and Truck Pullinghttp://www.racingjunk.com/Haulers/181855091/Motivated-Seller-Make-Offer.htmlThu, 06 Jun 2013 10:28:28 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181853902/Mini-rod-Chassie.htmlF 106 with 620 ring and pinion ,wilwood brakes ,wyson rails with advance front end. Motor plates for both Chevy or kb fuel tank in rear. Firm 559 381 0082Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181853902/Mini-rod-Chassie.htmlThu, 06 Jun 2013 09:17:15 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181754491/parting-out-super-stock-OFFERS-ACCEPTED.htmlalso drive shafts and seat. Above Added: Tue March 26, 2013, 1:52 pm ESTPARTS LEFT: 70 front, seat,crank trigger,valve covers,dry sump system ,crank, rods, set of cepex on 8 bolt 18" real wheels , radiator,pump,dual fan , steering orbitalAbove Added: Sat March 23, 2013, 8:01 am ESTIF YOUR INTERESTED ALL OFFERS ACCEPTED Above Added: Sat March 16, 2013, 7:52 am EST70 front narrowed 74"6.20 big avles billet joints powerlock1200.00,106 narrowed 62"1200.00, profab case 11 sets gears 200-800 oring case w/2-1480 1-1410 yokes 2,700.00 pro fab reverser 1480 1,600.00 48",43",& 23" shafts new 1 1/2" axles spare axles for 70 &106 spare front and rear axle new 1/12" 35 splint axle dive flangesslip yokes new billet front axle joints.5 gal stainless tank battery box. howe radiator mazier remore pump w/ dual fanssteering orbitalmoros vacuum pump. dart big m block readt for assembly 40600 callies 4" crank, oliver billet rods. complete dry sump system 6 stage auto verde pump peterson tank w/ 2 filtersmilodon gear drive crank trigger aero motive fuel pump w/ mallory filter. and losts more misc parts. please call Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181754491/parting-out-super-stock-OFFERS-ACCEPTED.htmlThu, 06 Jun 2013 03:45:16 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181847723/2wd-chassis.htmlI have 2wd chassis called humdinger that I pulled with outlaws.27 ford roaster body,f106 rearend with 6.20 gears with planetars.scs twin counter shaft trans with 3 sets of gears,scs reverser with brake,soild shafts and couplers.Has 1/2 inch thick aluminum drive shaft covers.Driveline has less than 50 passes.msd 10 plus box and coil,wilwood master cly and pedals,kirkey seat and cover,old style gaint pullers 18.4-16.4,also comes with all lead weights,gauges and aluminum feul tank.Can sead more pics.any questions call Bryan at 712-898-9890,asking 10,000.Also will sell complete with blown 528 bbf with 3 pass on rebuild,also has 3 pass on blower rebuild.Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181847723/2wd-chassis.htmlWed, 05 Jun 2013 18:47:57 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181853871/67-72-Chevy-GMC-8-Fiberglass-Fleetside-Skins.htmlNew old stock 67-72 GMC Fiberglass Fleetside Bedsides 8' - Pair (right and left sides for the price). Skins for a 127" wheel base, No modification, relocation or enlargement of wheel wells - stock location. Purchased in 2002 from US Body Source Inc. - Florida - www.usbody.com , but have never been mounted or worked on in any way. Stored since purchased. List new for $1,098. Smooth grey gellcoat exterior finish, fibergass textured black lacquer inner from factory. **Skin only - WILL NOT BOLT TO STOCK LOCATION** side lights and tail lights are blanked in. Buyer responsible for delivery or can pick up at seller's location. $600 Or Best Offer Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181853871/67-72-Chevy-GMC-8-Fiberglass-Fleetside-Skins.htmlWed, 05 Jun 2013 09:39:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181852168/pro-fab-munice-465-3-speed-trans.html465 munice 3 speed trans w/#4 head setTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181852168/pro-fab-munice-465-3-speed-trans.htmlMon, 03 Jun 2013 19:38:15 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Gear/181852036/scs-gearbox-and-clutch-assembly.htmlComplete SCS gearbox and clutch assembly rated for 1500hp and two wheel drive application. Call or text 740-438-9297 in central ohioTractor and Truck Pullinghttp://www.racingjunk.com/Gear/181852036/scs-gearbox-and-clutch-assembly.htmlMon, 03 Jun 2013 17:37:13 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181851591/PRO-FAB-REVERSER.htmlNO EMAILS - I DO NOT CHECK THIS SITES INBOXAbove Added: Mon June 3, 2013, 11:46 am ESTBrand NEW never been used!! Pro Fab Reverser $2100 Call 715-497-2756Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181851591/PRO-FAB-REVERSER.htmlMon, 03 Jun 2013 11:40:33 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181851385/brand-new-648-motor.html648 cu in natural aspirated motor,11.1 dart block,.600 raised 55 mm cam with roller bearings,4.625 je pistons with pro series grp rods,callies custom 4.825 crank,4 stage dry sump pan & pump,jesel front drive belt & distributor,brodix 12 degree heads wiyh t&d 1 pc rocker system,manton push rods,hre custom intake with dual enderle throttle bodies,down nozzles,fuel system is complete,brodix valve covers,ati damper.call 540-554-2012 or 540-247-0159 for infoTractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181851385/brand-new-648-motor.htmlMon, 03 Jun 2013 08:32:01 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181851025/South-Bend-dual-disc.htmlThis is the HD clutch for sled pulling.Above Added: Tue June 4, 2013, 6:53 pm ESTSouth Bend dual disc full ceramic with hydro master& slave never pulled Fits 05.5 - present $750.00 plus frt ship only Cont USTractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181851025/South-Bend-dual-disc.htmlSun, 02 Jun 2013 21:55:22 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181850982/MINI-ROD-PULLING-TRACTOR.htmlMini Rod Pulling Tractor. 600 cc Arctic Cat 2 stroke engine professionally built by McIntosh Motor Sports. Lectron carbs. VDO tach. Spare engine and engine parts. 26x12x12 Pit Bull II tires. Kuboto tractor body. Very competitive in the open classes. Very nice looking machine. $5500.00. Call 330-844-2080 for more information. Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181850982/MINI-ROD-PULLING-TRACTOR.htmlSun, 02 Jun 2013 21:13:28 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181850263/FORD-McLeod-Flywheel.htmlFORD 302/351W/351C McLeod steel FlywheelTractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181850263/FORD-McLeod-Flywheel.htmlSun, 02 Jun 2013 09:08:20 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Gear/181850256/DANA-80-5-38-Ring-Pinion.htmlDANA 80 Ring and Pinion set. DANA P/N 51011 & 51013 includes ring gear bolts and pinion bearing. Tractor and Truck Pullinghttp://www.racingjunk.com/Gear/181850256/DANA-80-5-38-Ring-Pinion.htmlSun, 02 Jun 2013 09:02:34 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181850088/Nitrous-Works-Billet-Atomizer-200-400.htmlI need a fuel pump .... will trade for magna fuel 300 or 500 series .... pump only Above Added: Sun June 2, 2013, 2:07 am ESTNitrous works billet atomizer oxide system ... kit comes complete with flow chart and new dual outlet purge valve ..... comes with bottle also .... bottle is in excellent shape .... no feed line or bottle brackets... but other than that all is there .... I need a fuel pump .... will trade for a magna fuel pump 300 of 500 series pump .... pump only .... Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181850088/Nitrous-Works-Billet-Atomizer-200-400.htmlSun, 02 Jun 2013 02:01:24 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Wanted/181849224/wanted-5.13-gears.htmllooking for 5.13 gears for dana 60 front, gm 14 bolt or dana 80 rear. call 607-865-7817Tractor and Truck Pullinghttp://www.racingjunk.com/Wanted/181849224/wanted-5.13-gears.htmlSat, 01 Jun 2013 07:51:33 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181848684/1979-FORD-350-HIGH-BOY.html1979 Ford-350 High Boy: New Dana 80 Rear 410 w Spool New Dana 60 Front 410 with spool Perfect Sheet Metal Show Quality Custom Dash all gauges Fuel Cell with Pump & Regulator Weight Box 2 - Sets of Wheels 1 - Set Traxus Tires Electric Over Hydraulic Steering Kit 4 Speed Trans and Lakewood Bell Housing McCloud Duel Disk Clutch Also - Automatic Trans Option Turbo 400 with Ford Bell Housing 1 - 5500 Stall Torque Convertor New Divorced Transfer Case w/Pro Fab gears 7AL Digital Box Wired with Painless Wiring System *More misc. parts (NEW and used) **NO ENGINE $12000.00 Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181848684/1979-FORD-350-HIGH-BOY.htmlFri, 31 May 2013 17:43:20 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181848346/1999-dodge-body.htmlthis is a full fiberglass body. never painted. mounted in round tube frame work...will post pics in a day or soTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181848346/1999-dodge-body.htmlFri, 31 May 2013 11:50:34 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/2736217/97-Chevy-2WD-Street-Modified.htmlPrice lowered to $12,500Above Added: Mon March 11, 2013, 1:31 pm EST1997 Chevy 2WD Street Modified Pulling Truck with 468 BBC with 750HP. Rectangle port heads, ported to the max. 1050 Dominator carb. 13.5:1 compression. Vacuum pump. Eagle rods. Steel crank. 2 disc Ram slipper clutch with 4 speed transmission with Profab third gear. 2.5 ton rear end with 31 x 15.5 Cepek pulling tires. Won 30 points chamionships in NPPA. Asking $15,000 Ken 402-720-4969 Craig 402-719-4305Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/2736217/97-Chevy-2WD-Street-Modified.htmlThu, 30 May 2013 10:09:24 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181846101/Light-4WD-Pulling-Truck.html1998 Ford Ranger, ProFab Gears, Big block Ford, Very strong pulling truck with extra gears. READY TO PULL.GREAT PRICE!!!Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181846101/Light-4WD-Pulling-Truck.htmlWed, 29 May 2013 15:33:48 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181845068/Chevy-Pulling-Truck-Roller.htmlComplete Truck less Motor We ran this truck in the Flinthills Truck Pulling Association in Kansas. Set up for the Modified 4x4 class Turbo 400 tranny Stall Converter 208 Transfer Case Berry Grant Fuel System Dana 60 Front Axle Dana 60 Rear Axle New Windshield and Rear sliding Glass Front clip is one piece, inside is stripped, bed is stripped on inside, custom built hitch to make you pull off of the axle not the back bumper. Too much to list. Please call or text 620-344-2177 for more info or pics. All you need is your BBC and some aggressive tires and your ready to start pulling! We had a 408 BBC in it Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181845068/Chevy-Pulling-Truck-Roller.htmlTue, 28 May 2013 18:47:36 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181843216/1985-chevy.html1985 1 tonchevy truck 3 speed pro fab 465 munice trans pro fab transfer case c 103 rockwell rear 5.29 gear welded dana 60 front extra set axles 276 620 1185 serious contacts only Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181843216/1985-chevy.htmlMon, 27 May 2013 11:50:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181842441/1999-Chevrolet-2500-Pulling-Truck.html1999 Chevrolet 2500 pulling truck. Electric hydrolic steering 33 x 1250 x 17 truxes tires new aluminum rims just rebuilt 400 transmission 2.72 transfer case adjustable hitch removable weight rack 406 small block chevy 245 afr heads scat crank oliver rods wisco pistons comp cam high volume oil pump dart block t and d shaft rockers 3/8 push rods edelbrock super victor 4500 flange aed dominator 1050 carb 6 al msd blaster 2 coil ati super damper no runs on this engine just been rebuilt last block cracked new block has been installed all other componets have approxiatmently ten passes block has dyno time only dyno at 720 hp at 7100 rpms have over 25000.00 invested in motor any other questions contact adam at 2525623754 serious inquires onlyTractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181842441/1999-Chevrolet-2500-Pulling-Truck.htmlSun, 26 May 2013 17:28:13 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181842178/489-Big-Block-Chevy.html489 cu. in. GM block, four bolt mains w\arp studs. Eagle 4340 crankshaft; 4.250 stoke std.rods,std.mains. Internal balanced on Clevite H series bearings. Eagle H beam rods 6.385 long. JE 118520 open chamber dome pistons 13.5;1 compression. 1/16 1/16 3/16 rings. World Merlin 345 cast iron heads,fully ported w/Ferrea 2.300 intake valves and 1.880 exhaust valves. Comp Cams 944 Dual valve springs W/731 titanium retainers and 612 locks, ARP rocker studs with comp cams guideplates, comp cams4021 stud girdle, comp 1320 roller rockers, comp cams 306cr-8 solid roller camshaft on dura bond CHP-12 cam bearings, comp 819 roller lifters, comp 3110kt timing set. Edelbrock EDL 2907 Victor Intake fully ported and matched. ATI Super Dampener. Holley 8896-1 1050cfm Dominator carb. Melling 10777 oil pump. also have trany sm465 W/profab 3rd gear but has chip tooth, np205 transfercase W/Profab gears in it, and Mcleod twin disc clutch plus fly wheel,and steel bell housing have sfi #Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181842178/489-Big-Block-Chevy.htmlSun, 26 May 2013 12:23:43 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181816028/648-Steve-Schmidt-Motor.htmlHere is a 648 Steve Scmidt pulling engine.4.9 bore, Raised deck block. MSD frount drive distributor with a MSD crank trigger. Fuel injection system built by Bamber Performance, all plumbing included for injection. Motor is complete from injection to pan with headers. This is a VERY strong running motor. $30,500.00 OBO Jeff (616)836-1876Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181816028/648-Steve-Schmidt-Motor.htmlSun, 26 May 2013 08:01:11 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181840495/Chevy-Pulling-Truck.html4 Wheel DriveAbove Added: Fri May 24, 2013, 6:57 pm ESTI have a 1977 Chevy Merlin 10/200 tall block 632 cubic inch- alcohol fuel injected Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181840495/Chevy-Pulling-Truck.htmlFri, 24 May 2013 17:03:20 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Haulers/181750725/Ford-F-350-Dually-Great-Condition.htmlany reasonable offer considered rite to refuse just lookersAbove Added: Tue May 21, 2013, 5:23 pm ESTLariat PackageAbove Added: Tue March 5, 2013, 11:09 am EST2000 Ford F-350 200k miles New tires 7 3 Powerstroke Extended Cab Four Door 6 Speed Manual Transmission Long Bed Tractor and Truck Pullinghttp://www.racingjunk.com/Haulers/181750725/Ford-F-350-Dually-Great-Condition.htmlFri, 24 May 2013 16:47:09 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Haulers/181750737/40-Gooseneck-United-Trailer.htmlany reasonable offer may be consinderedAbove Added: Tue May 21, 2013, 5:21 pm EST2008 United Trailer 40' Gooseneck Tri-Axle 7000 LB Axle 7'6" Swing door in Back Side Door Includes wench Tires like new Interior lights and 110 plug insTractor and Truck Pullinghttp://www.racingjunk.com/Haulers/181750737/40-Gooseneck-United-Trailer.htmlFri, 24 May 2013 16:47:08 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Turbochargers/181839270/HX-82-3.9-WITH-28-CM-EX-HOUSING.htmlLike the title says. Was BOUGHT IN JAN OF 2012 HAS 7 HOOKS ON IT TOOK IT OFF TO GO A DIFFERENT ROUTE. HAS A CAST WHEEL AND A V BAND discharge. Asking $2500 obo. Any question text or call seven24-31seven-7430 Tractor and Truck Pullinghttp://www.racingjunk.com/Turbochargers/181839270/HX-82-3.9-WITH-28-CM-EX-HOUSING.htmlThu, 23 May 2013 15:06:46 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181837295/526-ci-427-block.htmlfresh turn key motor 1050 dominator carb 990 cast corvette heads MSD ignition 13.5 compression 810+ horse Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181837295/526-ci-427-block.htmlTue, 21 May 2013 20:01:52 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181837174/1966-blue-pulling-truck.htmlI have a 1966 Chevy pulling truck that is ready for the track has new tires on it only 2 runs on them. the truck has graphics on it. the motor is a clean 468 cubic inch 454. roller rockers, ross piston, MSD distributor. merlin heads, computation cam. scat crank, many more extras. serious callers only and I will give further information on the truck and motor and both can be sold separate if need be. Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181837174/1966-blue-pulling-truck.htmlTue, 21 May 2013 18:02:27 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Haulers/2429389/Freightliner-w-91-Supreme-Crp-400-horsepowe.htmlFreightliner w/ '91 Supreme Crp 400 horsepower cat, 13 speed transmission, box is 26’ long; living quarters 84" by 97" wide, L shaped couch; bed; inside storage dimensions-18.5' long by 97" 102" tall currently used for two wheel drive puller; Bifold ramp; 7000 watt Owen Marquee ; 19' electric 12v awning; 4 aluminum underside storage; tires like new; includes Polaris ATV carrier on back. Aluminum wheels excellent condition; Call MIKE at 507-951-9695. Price reduced to $18,500!! Tractor and Truck Pullinghttp://www.racingjunk.com/Haulers/2429389/Freightliner-w-91-Supreme-Crp-400-horsepowe.htmlTue, 21 May 2013 03:45:20 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Chassis/181835041/SUPER-MOD-4-WHEEL-DRIVE.htmlCHEVY SSR FIBERGLASS TILT BODY 2600 hp sassy hemi ssi all the best This truck is ready to go This truck is very competative and a proven winner!Tractor and Truck Pullinghttp://www.racingjunk.com/Chassis/181835041/SUPER-MOD-4-WHEEL-DRIVE.htmlSun, 19 May 2013 21:52:00 -0400Tractor and Truck Pulling For Salehttp://www.racingjunk.com/Engines-and-related-components/181834995/-78-Chevy-Stock-II-Truck.html1978 Chevy Stock II 4x4. 468 Cu Inch. Pro-fab transmission and transfer case. Call for more information M-F after 3:30pm EST, or anytime on weekends, or email wtherndon@gmail.com Tractor and Truck Pullinghttp://www.racingjunk.com/Engines-and-related-components/181834995/-78-Chevy-Stock-II-Truck.htmlSun, 19 May 2013 21:14:12 -0400Tractor and Truck Pulling For Sale