Recent images in AllTheMods

.:Uploaded: Thu, 05 Sep 2019 17:32:48

jponkko@metku.net — Thu, 05 Sep 2019 17:32:48 +0200

By Evenge

Case on my desk. Side panels etc not sanded in this picture.

Case inside:
https://www.youtube.com/watch?v=U9LtNhHbWBI

How dust filter in front of the case works:
https://www.youtube.com/watch?v=lqVAsGhxOwM

.:Uploaded: Thu, 05 Sep 2019 17:31:50

jponkko@metku.net — Thu, 05 Sep 2019 17:31:50 +0200

By Evenge

Case finished.

Case inside:
https://www.youtube.com/watch?v=U9LtNhHbWBI

How dust filter in front of the case works:
https://www.youtube.com/watch?v=lqVAsGhxOwM

.:Uploaded: Thu, 05 Sep 2019 17:31:28

jponkko@metku.net — Thu, 05 Sep 2019 17:31:28 +0200

By Evenge

Case finished.

Case inside:
https://www.youtube.com/watch?v=U9LtNhHbWBI

How dust filter in front of the case works:
https://www.youtube.com/watch?v=lqVAsGhxOwM

.:Uploaded: Thu, 05 Sep 2019 17:17:06

jponkko@metku.net — Thu, 05 Sep 2019 17:17:06 +0200

By Evenge

Realized I haven't updated progress in here. I gave up the water-cooling idea and instead used regular air cooling, and mounted small SFX psu at the bottom of the case.

.:Uploaded: Fri, 01 Feb 2019 20:30:56

jponkko@metku.net — Fri, 01 Feb 2019 20:30:56 +0200

By Lcdlo

"Old school" aegis mod nearly done.

Connectors on left, next to fans are for the itx board behind the atx board.. that build is still in progress.

.:Uploaded: Fri, 01 Feb 2019 20:29:16

jponkko@metku.net — Fri, 01 Feb 2019 20:29:16 +0200

By Lcdlo

"Old school" aegis mod nearly done.
Connectors are under the latch on top of the case..

.:Uploaded: Fri, 01 Feb 2019 20:28:40

jponkko@metku.net — Fri, 01 Feb 2019 20:28:40 +0200

By Lcdlo

"Old school" aegis mod nearly done.

.:Uploaded: Fri, 01 Feb 2019 20:28:19

jponkko@metku.net — Fri, 01 Feb 2019 20:28:19 +0200

By Lcdlo

"Old school" aegis mod nearly done.

.:Uploaded: Fri, 21 Dec 2018 06:58:26

jponkko@metku.net — Fri, 21 Dec 2018 06:58:26 +0200

By crayonbox

Another Up Close picture

.:Uploaded: Fri, 21 Dec 2018 06:57:45

jponkko@metku.net — Fri, 21 Dec 2018 06:57:45 +0200

By crayonbox

Finally Built this Rig.. Forgot to post final pictures.

.:Uploaded: Sat, 05 May 2018 07:24:18

jponkko@metku.net — Sat, 05 May 2018 07:24:18 +0200

By crayonbox

Final Workmanship

.:Uploaded: Sat, 05 May 2018 07:23:41

jponkko@metku.net — Sat, 05 May 2018 07:23:41 +0200

By crayonbox

Finally sanded and painted black expoxy color to show off the lettering of my choice for my mobo.. :)

.:Uploaded: Fri, 12 Jan 2018 02:06:13

jponkko@metku.net — Fri, 12 Jan 2018 02:06:13 +0200

By crayonbox

Will this part messed up if I have it painted Copper? I have a Copper based theme for MOD I want to do.

.:Uploaded: Sat, 26 Aug 2017 08:08:14

jponkko@metku.net — Sat, 26 Aug 2017 08:08:14 +0200

By crayonbox

More clean now..

.:Uploaded: Sat, 19 Aug 2017 12:10:51

jponkko@metku.net — Sat, 19 Aug 2017 12:10:51 +0200

By willek

Places for 3 hdd:s. Kontron mini-Itx mobo in the middle. DC stepdown psu and 2,5 boot disk below. Photo is old, boot disk has since been replaced with ssd.

.:Uploaded: Wed, 09 Aug 2017 06:47:15

jponkko@metku.net — Wed, 09 Aug 2017 06:47:15 +0200

By crayonbox

More Up Close shot. I used a Dremel to cut and sand down smoothly.

.:Uploaded: Wed, 09 Aug 2017 06:46:28

jponkko@metku.net — Wed, 09 Aug 2017 06:46:28 +0200

By crayonbox

This is the route I decided to go for.

.:Uploaded: Wed, 09 Aug 2017 06:45:41

jponkko@metku.net — Wed, 09 Aug 2017 06:45:41 +0200

By crayonbox

As you can see it has a nice round bend to it. It matches my ERGO arms perfectly!

You can see the drawing on the PVC pipes. I was planning on using Dremel to cut from one end to other then I decided not. I was afraid it would have weaken the PIPE to bend easily.

You will see in next Image what I did...

.:Uploaded: Wed, 09 Aug 2017 06:43:43

jponkko@metku.net — Wed, 09 Aug 2017 06:43:43 +0200

By crayonbox

I bought a 10 foot PVC PIPE. I also used duct tape on the end of the PVC pipes. I add the sand inside the PVC pipes. I filled it up and taped it off with duct tape again.

Then I had to tape and roped one end of the PVC pipe to my ergo curved bar. I then asked my wife to help with the heat gun heating the PVC pipes while I bend it little by little to get the result I wanted.

It was a headache I tell you. It wouldn't budge at first so I turned up the heat then finally I could feel the nice bend to start happening.

.:Uploaded: Wed, 09 Aug 2017 06:40:27

jponkko@metku.net — Wed, 09 Aug 2017 06:40:27 +0200

By crayonbox

All the wiring clutters! UGH..