Retro Cade Spot

Ford Explorer OHC, Power Dimming Mirror, and Lighted Vanity MIrrors

2012-08-18T21:55:00.000-07:00

Definitely my favorite Ford Ranger mod so far. Overhead Console from a 95-99 Ford Explorer, powered dimming rear view mirror, and lighted vanity mirrors.

Console really looks like it belongs, a bit of a headache on the wiring side, and cutting into the headliner and grinding holes in it for mounting the slotted tabs of the console are not for the weak of heart.

2012-08-18T21:27:00.004-07:00

Here are the finished seats. Went in okay, hardest part was modifying the mounting bracket bolt holes so that I could accommodate the center console which is a shorty one from a Ford Explorer.

I will likely recover the armrest so that it matches the seats better.

2012-08-18T21:12:00.003-07:00

Here are some parts from the new doors, here you see the powered motor to lift the Window. Not a lot different from the manual one other than this one has a motor, mates up to the same track that is just above the post you see on the right. That post doesn't really need to come out and can stay in your car if you are swapping parts over.

Door Installation Ford Ranger

2012-08-18T21:08:00.000-07:00

Here's the old perfectly good but unpowered door. The door liner is a lot nicer on the new doors in addition to having power. Here is a picture of the doors I am gutting the parts from.

You don't have to swing that much over from these doors, I had to swing the lock latch that had the solenoid for the door lock knob, and the powered window motor which just slid into the old track.

I also had to move the new power harness over but everything else mated up. The only hard parts were the plug for the speaker/sensor/ on the drivers side is way up in the dash, I'm dropping the dash anyway but don't think you could connect it without doing so. Additionally you have to drill out the rivets that hold the old power door motor and use bolts or rivets again to install.

So far I have only the drivers door swung over. Tomorrow I'll drop the dash and install the harness and swap the passenger door. Not sure the harness will work, it's a 2008 and from a 4WD but we'll see.

Manual Window Swap Ford Ranger

2012-08-18T09:42:00.000-07:00

Above is harness from a 2008 FX4 Ford Ranger. I'm going to try and swap this harness into my dash of a 2007 Ford Ranger 2WD Sport model and to get the additional wiring for the power windows and locks.

I'll likely need to get the GEMs unit programmed once everything is swapped in to make the locks/windows/mirrors to work as these weren't original factory equipment on my truck.

Big thing will be to get the harness in though and hopefully the truck will start, and all the lights, heater, and other electronics will work.

Bottom picture shows the new door liner, a lot nicer than the very basic manual ones I have with no map pocket or fabric trim.

Pressure sensor plate

2012-08-09T22:05:00.000-07:00

Above is a pressure sensor plate that had to be fabricated to swap the pressure sensor mat from the original passenger side seat to the new installed eddie bauer explorer one you see above.

This plate was installed with the sensor pad above it under the springs so that it will turn the airbag on for the passenger side whenever significant weight is on the seat.

Ford Explorer Seat Swap in Ford Ranger

2012-08-07T22:08:00.000-07:00

Found a great set of Leather Eddie Bauer Limited Ford Explorer seats, working on swapping them over to a 2007 Ford Ranger. Challenge is the Ford Ranger has an airbag sensor pad that deactivates the passenger airbag when the seatbelt is connected and a weight less than a certain amount is detected. Need to swap this over to the new seats somehow, and make a few fabrication changes to accomodate the seatbelts which have pre tensioners.

2012-05-25T21:29:00.001-07:00

Got the vinyl racing cabinet decals applied now, turned out great, M Power.

Dirt 2 Racing Video in Racing Cabient

2012-04-18T06:53:00.001-07:00

Racing Cabinet Video E46 M3 Need for Speed Shift 2

2012-04-18T06:52:00.002-07:00

Racing Cabinet Complete with Speakers and Spolier

2012-04-15T12:21:00.002-07:00

Added the Z906 speakers to the system. Only downside is I have to reduce the audio quality from the PS3 to also drive the buttkicker. I'll have to look into other connection options but it works good for now.

The fin is also installed and just rests on top of the cabinet for easy removal.

Video Overview of Visual Pinball Machine and Hyperspin

2012-04-12T16:52:00.000-07:00

Racing Cabinet Almost Completed

2012-04-10T21:00:00.002-07:00

Waiting on a Z906 sound system I ordered from Logitech which is THX certified and should really work great. Also need to mount the spoiler and apply the graphics which I'm still working on but here is the fully working cabinet, with a butt kicker gamer, PS3, G27, and television. All wires are run out of sight.

Racing Cabinet Painted

2012-04-03T20:41:00.002-07:00

Racing cabinet is all dissassembled for painting. Went with a gun metal grey since black would have made it look way too big. Paint is turning out well and should be completed shortly.

0-60 Need For Speed Racing Cabinet Nearly Completed

2012-04-03T20:39:00.003-07:00

Here's a picture of the racing cabinet nearly completed, this piece slides into the hood to complete the cabinet and then only the spoiler needs to be attached.

Seat should work well, can be adjusted forward and back and also tilts, the wheel mount is also very adjustable so should accomodate all sizes.

Big Bang Bar Pinball

2012-03-26T20:59:00.002-07:00

Didn't really document the build but here is a Big Bang Bar Virtual Pinball I built using Hyperspin as the front end.

Plays nice with a 7 solenoids, a shaker motor, and 3 cree RGBW LEDs for effects.

Happy with how the artwork came out, much brighter then my bride of pinbot original cabinet.

Side Panels for Racing Cabinet

2012-03-26T20:52:00.002-07:00

Completed the racing cabinet side panels, lots of pieces but assembly is not to bad. Biggest pain of building this Racing Cabinet so far is all the strange dimensions you need requiring you to rip 2X4s and 1X3s ad nausea.

Racing Cabinet Hood

2012-03-26T20:47:00.002-07:00

Completed the racing cabinet hood the other day, it's very large. To accommodate a 42 inch TV though there isn't much option. I could have reduced the side width I suppose but it makes a nice canvas for some racing art so I left it the way it was.

Should give really deafening acoustics with the 5.1 sound I plan for it.

I had to modify the design a bit so it could be assembled and disassembled easily, rather then being permanently affixed as it won't fit in any doors I know of. Certainly wouldn't go in the basement, I have it now so that the back pieces and shelf all come off for easy moving and to fit through doors.

Racing Cabinet

2012-03-26T20:45:00.002-07:00

Inspired by the Need for Speed racing cabinet build, I've decided to recreate my own version. Pretty similar but will change a few things, and although I like the art on this cabinet will likely do something different.

Ambilight with New TV Back Plate for better Brightness

2012-01-29T21:43:00.000-08:00

8X8 LED Matrix with HL1606 RGB LEDs

2012-01-29T21:35:00.000-08:00

Ambilight Solution Random Color Swirl

2011-12-11T16:26:00.000-08:00

Here is the Ambilight solution playing a random color swirl that is not tied to the video on the PC.

Ambilight DIY Solution

2011-12-11T16:20:00.000-08:00

Been playing with my own Ambilight Lighting solution. This solution uses LEDs and WS2801 chips to allow me to address them indvidually.

Solution works fairly well but will try again with brighter LEDs.

Nintendo PC Gameplay Hyperspin

2011-10-01T22:12:00.001-07:00

Nintendo PC Internals

2011-10-01T22:11:00.001-07:00