Some Of My Experiment With Science

Get Lapu R-Offer Software is cheapest Software With High Functionality

2017-03-30T05:43:00.000-07:00

GET-PATEL-BRO

Patel Telecom Bidada

Bhuj-Kutch

Contact : 7567566104 , 8141636468

Get Lapu Introduction

Table of contents

1:- Objectives……………………………………………………..

1. Introduction………………………………………....

2. Operational View……………………………………………………..

3. R-offer selection Window………………………………………….

4. Recharge List …………………………………………………………….

5. Add Recharge…………………………………………………………….

6. Add Bulk Recharge …………………………………………………….

7. Send SMS …………………………………………………………………..

8. SMS list ………………………………………………………………………

9. DEMO Pin …………………………………………………………………..

2- Technical Data Protocol To communicate

1. Fetch Recharge From Existing Website ………………………………

2. Update The Recharge on Existing Website…………………………

1:- Objectives

The Objective of Developing this Get Lapu Documentation is that any third party user can easily understand the Operational Working of the Software and hardware of Get Lapu System

Get Lapu R-Offer Software is cheapest Software With High Functionality

Get Lapu software is designed for the Recharge from the Demo Lapu Sim card of the User with Auto R-offer selection

Speed of recharge 1 recharge per 20sec (Speed is set by seeing the operator consideration)

Currently System is available for on Idea and Airtel Demo Lapu Sim Card

We are Providing Multi Recharge Solution to the User with Customized solution as per the personal needs of the user with online services

Get Lapu is software which select the R- Offer of the Customer’s Mobile Number from Available Offer and gives extra Benefit to the Owner without any extra cost .so owner will get Fixed margin + extra Benefit per Recharge , Which increase the Profit to the Owner

User Minimum System Requirement

1. Computer system with Good RAM and Processor

2. Good Internet Connection (with constant ping)

3. Own Recharge Website (if not available then will be provided by us with cost)

System which we provide

1. GSM lapu Modem (With cable and power supply)

2. Get Lapu System Software

3. Help In miscellaneous software Installation

1. Operational View

In operational window we can see list of the recharge with current status, you can change the recharge Status from this panel and also start and stop the online recharge fetch pending.

3.R-offer selection Window

Example .01

Example .2

Example .3

This window will show you the current status of the recharge

It will automatically select the User R-Offer from the Offer menu and recharge it, if the offer not available then it will do directly

See Video for more information

4. Recharge List

You can search in the recharge list by following methods

1. Search By Date

2. Search By Operator

3. Search By Mobile no

4. Search By Amount

5. Search By Client Id

you can see and R-Update the Same Transaction to then sever from same Panel

5. Add Recharge

You can add direct Recharge from this panel to the System

6.Add Bulk Recharge

Enter Amount and press add Recharge

New Select Dialog Box will Open -> select .xls or .xlsx execl file

In execl file the all number must be in sheet1 in first line no other data have to be preset their otherwise it create miss-selection.

See the Below Photo Attached for more information

Select EXECLE file

Number in Excel File

7.Send SMS .

You can send SMS

User can send Send the SMS from this panel through the Software

8.SMS list

9.DEMO Pin

Demo pin per Operator

Technical Data Protocol To communicate

1. Fetch Recharge From Existing Website

link must be like following

http://www.xyz.com/get_pending_recharge

response:

RECHARGE_ID#MOBILE_NUMBER#AMOUNT#RECHARGE_CODE$

Example:

2398681#7201075815#50#I$2398682#8866792042#100#A$2398683#7567566104#55#I$

# and $ are must with Proper Placement in the response and $ must at end in every response

RECHARGE_ID = must be numeric in nature

Where Operator have following code with the link

Operator		Code
Aircel		AIR

Airtel		A
Airtel Digital DTH TV		ATV
BIG TV		BTV
BSNL - 3G		B3
BSNL - STV		BS
BSNL - TOPUP		BT
BSNL Recharge		BR
DISH TV		DTV
DOCOME-SPECIAL		DS
DOCOMO		D
IDEA		I
LOOP MOBILE		LM
MTNL - Recharge		MTR
MTNL TOPUP		MTT
MTS		M
RECHARGE VIDEOCON		VD
RECHARGE VIDEOCON	-	VS
SPL
RELIANCE - CDMA		RC
RELIANCE - GSM		RG
TATA INDICOM		T
TATASKY DTH TV		TTV
UNINOR		U
UNINOR - SPL		US
VIDEOCON RECHARGE		VD
VIDEOCON SPECIAL		VS
VIDEOCON DTH TV		VTV
VIRGIN - CDMA		VC
VIRGIN - GSM		VG
Vodafone		V
SUN DIRECT		STV

2. Status Update The Recharge on Existing Website…………………………

Status Update Url Parameter: (if transaction is in pending we call this url to update on your website to next Status = Success or Failure )

Please provide the status url for the recharge request to the Lapu Software . In Message you will get the following response:

Sample Url Format: http://www.yourdomain.com/pagename?Get_id="<OurId>"& Client_id ="<Your_Id>"&Status="<RequestStatus>"&Org_id="<Org_TransactionId>"&Lapu_Balance=" < Lapu_Balance > "&Remark="<Nothing>"

Example :

http://www.xyz.com/get_responce?Get_id=123456&Client_id=56574&Status=Succ ess&Org_id=GJ12354845&Lapu_Balance=2548& Remark=XYZ

Response will be in POST method , so be sure that your sever will get the Response in the POST method not in GET method.

Feel Free to contact us

Patel Telecom Bidada

Bhuj-Gujarat

Phone : 7567566104

Whats Up : 8511109772

Website: www.getpatel.com

E-mail: pateltelecombidada@gmail.com

Control System For A Small Industries With Low Budget & High Performance

2013-09-08T23:34:00.001-07:00

GUI Based Temperature & Level Indicator And Controller Using Internet Connectivity To Control From Any Where

Hello Friends Now here we design a one control system for a small industries,so that automation can also be possible in the small low budget industries with Automatic Control loop with Control Panel & Internet control panel so that they can observe & control sys from any where in the world.

Right Now basically cover only Two Close Loop 1 ) Temperature

2) Level

Here is the block diagram of the concept which we had design system.

In our control system is mainly divide in to 4 part
1. The sensor and transmitter at the Plant Field
2. The Heart of the system 89V51RD2 Controller + ADC0808
3. Graphical User-Interface At Control Room or Internet Panel.
4. Actuator And Display of the system ( Feed pumps, Buzzer Alarms,LCD Display)

Part 1 The sensor and transmitter at the Plant Field

We have used IR-Sensor for Level measurement of the fluid.Which consist of the pair of one Transmitter and one receiver. So that by reflection of the IR-wave will give the information of the level of the fluid. See the basic concept of it in the figure

The Output of the Receiver is changed according to the distance of the liquid form it. It is Directly proportional to Voltage generated at output.

For Temperature Measurement

We had used LM35 temperature sensor, Which will give output accordance to the Current temperature and then it is calibrated in the Celsius or Fahrenheit as our requirement. It is Directly proportional to Voltage generated at output 10mV/'C.

The output of the sensror are ANALOG so they are Given to the ADC0808 to convert it into the DIGITEL form as our controller is DIGITEL CONTROLLER

2. The Heart of the system 89V51RD2 Controller + ADC0808

We Have used 89V51RD2 Micro-controller for the controlling of the our system because of some Features like it

ISP system so that we can load our program easily into this and its.
5 V operating voltage from 0 MHz to 40 MHz
16/32/64 kB of on-chip flash user code memory with ISP and IAP
Supports 12-clock (default) or 6-clock mode selection via software or ISP
SPI and enhanced UART
PCA with PWM and capture/compare functions
Four 8-bit I/O ports with three high-current port 1 pins (16 mA each)
Three 16-bit timers/counters
Programmable watchdog timer
Eight interrupt sources with four priority levels
Second DPTR register
Low EMI mode (ALE inhibit)
TTL- and CMOS-compatible logic levels.

ADC0808

We had selected 0808 for the more Analog input can be added to it, as 0804 has 1 input analog input channel but 0808 has 8 analog input channels. Right now we had used 2 input only but for future expansion can also be considered here. that why we used ADC0808.

Here is the basic Circuit of 89V51RD2 + ADC0808 Design in PROTEUS

3. Graphical User-Interface At Control Room or Internet Panel.

We Basically Two Control panel are their : 1) SERVER CONTROL PANEL

2) INTERNET CONTROL PANEL

1) SERVER CONTROL PANEL

Here i have uploaded some control panel picture in below so you can understand the concept of it GUI + CONTROL of the sys.

Server Control Panel

2) INTERNET CONTROL PANEL

Internet Panel Basically Design for the multi-control of the one System From any where in the world .

This Internet Control Panel can be operated form any where from the world so the owner can see the Live status of their company . And also they have option to change the limits and set points. Maximum 254 Internet panels are see and control the panel.

4.Actuator And Display of the system ( Feed pumps, Buzzer Alarms,LCD Display,Actuator )

Now if any system is their then controlling variable is controlled by the final control element which can be a Pump,switch,motor , valve any type of the actuator according to their system it is their .

Now here i used the Pump as final controlling element . Two pump are their one is in flow and out flow. if the level is to low the in flow will automatically start and fill the water and if the level is to high then out flow will start and take out the water from the tank and maintain the level in the tank.

12 V DC Pump

This as Actuator for the system , it can also be Switch of control valve.

Now for Local Display

Here i used JHD 16x2 LCD

LCD JHD DISPLAY

This will show the status of the parameter locally at the near the instrument so the worker can see the parameter that that place .

Critical situation Alarm

For the Critical situation a alarm is place, which will give a voice alarm to the operator or worker the site of the instrument for inform them about the critical action so they can take required step about it clear that.

Buzzer

Here i used the Small 4-20V DC volt Which give a beep on getting volts.

Description Of System To The Final To Industrial Site

We all know that the Automation of the industry always going to have good profit and More safety to our worker and also for large costly instrument , But For a small industrialist it is very costly to use PLC ,SCADA , DCS in small industry,So my Business Concept is to provide a Full-automation to small industry within their budget By design a their controlling Instrument using High frequency Controller and GUI software like Visual basic ,lab-view, Mat-labe,& GUI softwares. So That the small industry can also get a automation with according to their low budget + high reliable their industry system with low man power & high profit output. In this system if they want we can also add the new feature internet view or internet control panel, so that the small industrialist can also see their company status form home or outside as we know industrialist don't have manager in their company by have Android software + computer software for observation of status . so they have all type of function in low Budget More Profit. I would like to give a automation to low budget company with their requirement and output criteria.

Here i had Maid one Live system which is Analogous to the industrial process . So we can easily get idea about the live real industrial system by this small model. The model is operating live so we can get real idea of function and working . We can also add PID Tunning in this System by adding much more function as per the required of the Client and function.

Blog writing is in progress please wait ......... Thank you

SMALL FM TRANSMITTER USING ONE TRANSISTOR

2012-07-22T13:37:00.000-07:00

Hello friends this one is the simple and basic Fm transmitter circuit using one transistor.

LONG RANGE FM TRANSMITTER

2012-05-05T22:48:00.000-07:00

Hello friends,
We know that building of Fm transmitter for first time is quite hard and we get confused about the components, parts, design, pcb, transmission frequency, inductor value and making of inductor , polarity of the capacitor and many things.

Here i am going to explain you a building of simple fm transmitter using a two transistor . I will try to explain as possible as i can. lets starts with the components required.

Transistor
Q1= BC547
Q2=2N2219

Capacitors
C1 & C2 =4.7uF(electrolytic)
C3,C4 &C7 = 100nF( ceramic 104)
C6 = 4.7 pF (ceramic )
C5= 10-30 pF (Variable capacitor or also known as TRIMMER )

Resistors
R1= 47K
R2= 220K
R3=4.7K
R4 & R5 =10k
R6= 100 ohm

INDUCTOR
L1= 8 turns of 22 Gauge copper wire around a simple ball pen.( I will upload a photo of it for more idea)

POWER SUPPLY
Battery (Power Supply) = 12-9 V DC (Always use battery and avoid adepter so i will
reduce noise in transmission )

HOW FM CIRCUIT WORK ? :

The circuit is basically a radio frequency (RF) oscillator that operates around 100 MHz. Audio from audio jack is fed into the audio amplifier stage built around the first transistor. Output from the collector is fed into the base of the second transistor where it modulates the resonant frequency of the tank circuit (the 8 turn coil and the trimcap) by varying the junction capacitance of the transistor. Junction capacitance is a function of the potential difference applied to the base of the transistor. The tank circuit is connected in a Colpitts oscillator circuit. It works on the principal of COLPITTS Oscillator.

ANTENNA IS MUST IN THE CIRCUIT:

A impudence matching ANTENNA is must required in the circuit,without Antenna circuit will never works .Generally we uses a telescopic antenna . which through the waves in the atmosphere .

A SHORT NOTE ON INDUCTOR :

It is easy to make take an 22 Gauge enameled copper wire and wound it on the ball-pen and make 8 turns on it tightly. i shown in photo below.

FM CIRCUIT CALIBRATION ( IMPORTANT PART :-     PLZ KEEP PATIENCE MAY BE                                                                 OF CIRCUIT )                    YOU NOT GET SUCCESS IN
                                       FIRST TRY OF
                                                                                  ADJUSTMENT.

Place the transmitter about 2-10 feet from a FM radio. Set the radio to somewhere about 89 - 90 MHz. Walk back to the Fm Transmitter and turn it on. Spread the winding of the coil apart by approximately 1mm from each other. No coil winding should be touching another winding. Use a small screw driver to tune the trim cap. Remove the screwdriver from the trim screw after every adjustment so the LC circuit is not affected by stray capacitance. Or use a plastic screwdriver. If you have difficulty finding the transmitting frequency then have a second person tune up and down the FM dial after every adjustment. One full turn of the trim cap will cover its full range of capacitance from 10pF to 30pF. The normal FM band tunes in over about one tenth of the full range of the tuning cap. So it is best to adjust it in steps of 5 to 10 degrees at each turn. So tuning takes a little patience but is not difficult. The reason that there must be at least 2-10 ft. separation between the radio and the TRANSMITTER is that the Transmitter emits harmonics; it does not only emit on one frequency but on several different frequencies close to each other.


Don't leave a circuit by just trying sometime try and try until you get some distortion in the fm receiver. once you get some distortion in it. that means your fm circuit is working. and if not then try to check all components and the soldering of your circuits and power supply .if you getting confusing about the power supply put one 2 Volt LED in series with 1K resistor in parallel with battery so you can easily get the on-off you fm transmitter.

ABOUT THE RANGE AND QUALITY (STRENGTH) :
I personally maid this project with great success i got a 1 km perfect range with proper quality of the signal after that up to 1.5 km small distortion starts and after that quality factor go down and then lost it. you should have to maintain the circuit in the metal case to protect it form the electrical isolation .

The range and quality are inversely personal to each other. Both can be increased by increasing the input voltage upto certain limit.

I JUST UPLOADING THE PICS FOR YOUR REFERENCE THAT I HAD MAID IT LIKE THAT. YOU CAN TRY IT BY YOUR OWEN WAY BY MAKING PCB OR ON SIMPLE HOLED PCB.

I used the simple copper plate and glue the other copper parts to place it on it

A telescopic antennae of proper height.

A inductor of the copper

A SIDE PHOTO OF THE CIRCUIT
If you have any problem and any question about it then you are always welcome.

From :
KALPESH CHHABHAIYA
(kpkpkalpesh@gmail.com )
mb: 8866792042

How to Make a robot ( four wheels and attack on enemy) Here we make a Robot X4-37

2011-12-31T02:42:00.002-08:00

Hello Friends today i going to explain you that how to make a simple robot. first of all we have to know about the robot, that what is it ?A robot is a mechanical or virtual intelligent agent that can perform tasks automatically or with guidance, typically by remote control. In practice a robot is usually an electro-mechanical machine that is guided by computer and electronic programming. Robots can be autonomous, semi-autonomous or remotely controlled. Robots range from humanoids such as ASIMO and TOPIO to Nano robots, Swarm robots, Industrial robots, military robots, mobile and servicing robots. By mimicking a lifelike appearance or automating movements, a robot may convey a sense that it has intent or agency of its own. The branch of technology that deals with robots is robotics.

Now we will start form the low level. Now we will make a simple robot which can perform the basic task like forward, backward, turn left ,turn right ,and one additional function like any weapon or a work.

We are going to start from a robot know as the X4-37 . which is generally used in the college level competition of fight .The X4-37 is consist of a wooden cheeses( which can be main base of the robot on which all the part are fixed), 4 Hi-Speed and Hi-Torque DC motor, 4 rubber wheels, a DC source , remote control,wires and any weapon of function .

Here is a model of X4-37

Left side view

A Upper -Back view

The all required things can easily available in the market or in local area .

Now we start form the cheeses .It is maid up or ply-wooden . which is cut in the required shape and size. as per our required work and the criteria .we can choose the strength of the ply depends on the material. now here we taken the size of the ply 25 x 35 cm as shown in the picture bellow. And the holes are maid as per the fixing of the motor's size and the length .

A upper side

A lower side

Next we required the Motors , wheels and a Dc source . we used a 150 rpm 4-motors ,4-rubber wheels and a 12-volts Dc source . as shown in picture below .

and for your clearance

Nut bolts and clip for the clipping or fixing of the motor with the wooden ply.