streamyx-modem-config

Zyxel Prestige 650H-E STREAMYX MODEM

2009-06-08T20:13:00.001-07:00

Accessing Your Prestige via Web Browser

Launch your web browser. Enter http://192.168.1.1 as the web address
Then enter the username and password:
- Username: admin
- Password: 1234
Then click OK
Then click at the wizard setup link
Then you will change the setting as this:
- Mode: routing OR bridge
- Encapsulation: PPOE
- Multiplex: LLC
- Virtual Circuit ID: VPI -0 & VCI -35
Then click Next
On the next page change the setting as this:
- Service Name: Streamyx
- Username: username@streamyx
- Password: your TMNet Streamyx password
- IP Address: Click on the obtain an IP address automatically
- Connection: Nailed-Up connection (if you want your internet connection to be online all time)
- Network Address Translation: Choose SUA only
Verify the setting on the next screen. Click on the Save setting
So right now your modem has been configuring to Auto-connection mode

ZTE ZXDSL 831 STREAMYX MODEM

2009-06-08T20:12:00.000-07:00

ZTE ZXDSL 831 is a modem / router supplied by TM. It works as a modem by default but you can change it to a router.

In router mode, you don’t need to dial Streamyx manually anymore. The router will dial it for you automatically.

How to Configure ZTE ZXDSL 831 Modem as a Router

Visit http://192.168.1.1 with the username and password. If you don’t know the default username and password:
- Username: ADSL
- Password: expert03
When logged in, click on the WAN tab
Click on ATM VC and make sure, interface aal5-0 VPI = 0 & VCI = 35, MUX = LLC, Max proto = 2
Click on PPP and then a new interface
Set the new interface as PPP interface = 0 ATM VC = aal5-0, protocol = PPoE, use DNS = enable, security = PAP. Don’t forget to set your TMNet Streamyx username@streamyx and also your password. Click Submit
After that, click on Admin and then Commit and then Reboot Once it’s done you should check your Internet connectivity by loading your favorite website

Port forwarding ZTE ZXDSL 831 for better Bit torrent speed. I know a lot of you guys are asking for this article so here it goes. Don’t blame me for anything if it doesn’t work for you. I provide no support for this post.

The ZTE ZXDSL 831 supplied by TMNet for its Streamyx service. It’s a cheap but quite powerful DSL bridge / router. It uses the GlobespanVirata chipset which is also known to be used to products like D-Link. Since this company has merged with Conexant, support files for the chipset have been removed. You might be able to find it somewhere.

A bit from the Bit torrent FAQ, The BitTorrent client will normally use ports 6881 to 6889, so when you are adding the ports to your firewall, make sure you cover the whole block. If you don’t know the default password, you should check out ZTE ZXDSL 831 default password.

After you login, click on Services tab. Under NAT Options list box, choose NAT Rule Entry. Click Add to add a new rule:

Rule Flavor: RDR
Rule ID: 15
IF NAME: ALL
Protocol: ANY
Local Address From: 192.168.1.x (Your Bit torrent Client IP)
Local Address To: 192.168.1.x (Your Bit torrent Client IP)
Global Address From: 0.0.0.0
Global Address To: 0.0.0.0
Destination Port From: 6681
Destination Port To: 6689

After done all that don’t forget to Click on Admin tab and then Commit and Reboot. Make sure to click Commit then Reboot.

UT-300R2 STREAMYX MODEM

2009-06-08T20:11:00.002-07:00

This one is another Certified DSL Modem by TMNET Streamyx.

Open your browser and type http://192.168.1.1 (default modem page)
For Username - ‘admin’, Password - ‘utstar’
At the Main Page, click ‘SETUP’
Click on the connections, and delete all information that has been setup inside it.
Click at New Connection, Put the name as Streamyx, key in your username and password,
Make sure that the setting is set ok such as vpi=0, vci=35 , NAT = disable, Type= PPOE, Keep Alive =0 (need to put 0 to disable it).
Go to Tools, System Commands, Save All, Restart.
Finish.

Stay tune for another type of modem that have the certification of TMNET.

TRIZ MODEM CONFIGURATION

2009-06-08T20:11:00.001-07:00

How To Configure Triz Modem

Set PC IP to 192.168.1.2 and Gateway to 192.168.1.1
Click on Internet Explorer and at address bar point to 192.168.1.1. Click Go
When Login Interface pops up, enter as below:
- LOGIN NAME: admin
- PASSWORD: telekomst / aaaaaaaa
To set Triz modem to PPPOE, click on WAN at the left side of the frame
Use the default Adapter Pvc0 and Click on Submit
Then you will see WAN Configuration Windows, please follow up this instruction and fill in the form.
- Bridged: Enable
- Encapsulation: PPOE LLC
- Enter your TMNet Streamyx login
  - Username: username@streamyx
  - Password: your TMNet Streamyx password
VCI: 35
VPI: 0
Make sure Automatic Reconnect is tick
Click on Save Setting and Reboot on the Left Frame
Click on the Save and Reboot button (This will write all the settings to the flash memory in the modem)

KASDA STREAMYX MODEM

2009-06-08T20:09:00.002-07:00

Here is a simple step by step instruction to turn your KASDA ADSL modem from Bridge mode to Router mode. How to turn KASDA ADSL Modem into Routing Mode.

Add a Root User

Open a browser and type the following URL: http://192.168.1.1/hag/emweb/PopOutUserAdd.htm
Wait for a while and a Popup Dialog box will appear asking for username and password. Type in the following:
- Username: user
- Password: password
Now add user page should appear. Add any username you like but make sure the user type is ‘ROOT’
Close your browser now. Please do not switch off the modem as doing so you would lose all steps done from 1 to 3
Open browser and type in http://192.168.1.1
Now Key in the username and password that you have created in step 3
Go the Admin Tab and select the Commit and Reboot, now click the button commit. This should save all the work done from steps 1 to 7

Turn KASDA into Routing Mode

Go to the Home Tab and click on the Quick Configuration
Make sure the following Options are filled in accordingly:
- ATM Interface: 0
- Operation Mode: Enabled
- Encapsulation: PPPoE
- LLC VPI: 0
- VCI: 35
- Default Route: Enable
- PPP Username: yourname@streamyx
- Password: your TMNet Streamyx password
Click the Submit button
Next, Select the System Mode. Make sure that all settings (radio button) are set to disable. Click the submit button
Go to the Services Tab
Click the NAT. NAT Options: NAT Global Info. Select the Enable radio button option and click the Submit button
NAT Options: NAT Rule Entry. Click on the Add button. Key in the following:
- Rule Flavor: NAPT
- Rule ID: 1
- IF Name: ALL
- Protocol: ANY
- Local Address From: 192.168.1.0
- Local Address To: 192.168.1.255
Click the Submit Button
Select the DNS
Click on the Enable radio button
Click on the Submit button
Go to Admin Tab
Select the Commit and Reboot
Click on the Commit button
Wait for the screen to refresh and Click on the Reboot Button. Now we are done. Now you can try to open a new browser and you should be able to browse the internet without using the PPPoE dialer from your PC

Huawei SmartAX MT800A CONFIGURATION

2009-06-08T20:09:00.001-07:00

Connect to 192.168.1.1
Key in:
- Username: admin
- Password: admin
Click on the ATM setting at left side menu
Please make sure that VCI-35, VPI-0, Encapsulation-LLC, Connection Type-PPP
After you choose PPP, it will prompt different table where u need to choose PPPoA/PPPoE - PPPoE, IP Unnumber-Disable, Default Route-Enable, Username: username@streamyx, Password: your password. Then click Submit
Click DHCP Mode and choose DHCP Server
Click IP Filter and select Security Level to None and then Submit
Click Save and Reboot, Save→ Submit, Reboot→ Submit

D-Link DSL500 CONFIGURATION

2009-06-08T20:08:00.000-07:00

Access the Web-based Manager

The Manager PC can now use a web browser to communicate with the Router.

Note: Be sure that the Manager PC is not configured to use a proxy server in the Internet settings. In Windows Internet Explorer, you can check if a proxy server is enabled using the following procedure:

In Windows, click on the START button, go to Settings and choose Control Panel
In the Control Panel window, double-click on the Internet Options icon
Click the Connections tab and click on the LAN Settings button
Verify that the Use proxy server option is NOT checked. If it is checked, click in the checked box to deselect the option and click OK

To use the web-based management software, launch a suitable web browser and direct it to the IP address of the Router. Type in http:// followed by the default IP address, 192.168.0.1 in the address bar of the browser. The URL in the address bar should read: http://192.168.0.1.

In the page that opens, click on the Login to web-based management module button in the center. A new window will appear and you will be prompted for a user name and password to access the web-based manager. Use the default user name admin and password admin for first time set up. You should change the web-based manager access user name and password once you have verified that a connection can be established. The user name and password allows any PC within the same subnet as the Router to access the web-based manager.

Once you have changed the connection method to PPPoE, saved the configuration change and restarted the device, you can proceed to enter authentication information used to connect to the WAN. Follow these steps:

Under PPPoE Login, enter the Login User Name used for your network account. The user name and login password, are used to authenticate the identity of the ADSL client and provide access to the service provider’s network. The user name and login password can be any combination of up to 64 characters
Enter the Login Password
Unless you are instructed to use a different Authentication method, leave the default chap protocol selected. The alternative method, pap, can be selected from the pull-down menu if required by the service provider
Leave the Connect on Demand option as enabled in the pull-down menu. This will allow the Router to establish a WAN connection upon restarting
Leave Idle Time set to the default value 0
Click on the OK button on the bottom of the window. A new screen appears
The Save changes and reboot system message prompt offers two option:
- You can save the configuration changes and restart the device now by clicking OK; or,
- If you want to change the user name and password used to access the Web Manager, select the Continue and do ‘Save Changes’ later option and click OK, and go to the System Username and Password menu in the Maintenance folder

PPPoA Connections

The default connection method used by the Router is Point-to-Point-Protocol over ATM (PPPoA). In the PPPoA Configuration window, you must enter the user name and password for network account authentication and
verification. When this information is entered, the changes must be saved and the Router restarted. In the Bridge/Router Configuration window, follow these steps to establish the WAN connection using PPPoA:

Under PPPoA Login, enter the Login User Name used for your network account. The user name and login password, are used to authenticate the identity of the ADSL client and provide access to the service provider’s network. The user name and login password can be any combination of up to 64 characters
Enter the Login Password
Unless you are instructed to use a different Authentication method, leave the default chap protocol selected. The alternative method, pap, can be selected from the pull-down menu if required by the service provider
Leave the Connect on Demand option as enabled in the pull-down menu. This will allow the Router to establish a WAN connection upon restarting
Leave Idle Time set to the default value 0
Click on the OK button on the bottom of the window
Save changes and reboot system message prompt offers two option:
- You can save the configuration changes and restart the device now by clicking OK; or,
- If you want to change the user name and password used to access the Web Manager, select the Continue and do ‘Save Changes’ later option and click OK, and go to the System Username and Password menu in the Maintenance folder

Caremo AS520 CONFIGURATION

2009-06-08T20:07:00.002-07:00

Local Internet Port (Web-browser)

Connect the Ethernet Port to your local area network (hub or switch) or directly to a PC (using the CAT5 RJ45 patch cable). Then launch the web browser and enter 192.168.1.1 to the web address box, press enter.

Login

You will see the Login interface (on the web browser) when you connect to the device through the Ethernet Port.

With the window active, type admin for both the Username and the Password and then click on the Apply button (The default username and password is admin)

Wizard

You can select the ISP services for each of the following protocols:

PPP over Ethernet (PPPoE) - Dynamic IP
PPP over ATM (PPPoA) - Static IP
RFC-1483 Bridge - modem only

NOTE: The Username and Password fields are required.

Username: username@streamyx
Password: your TMNet Streamyx account password
Confirm Password: re-enter password again for confirmation
VPI: 0
VCI: 35

Click on the Apply button to complete the configuration.

Click on the Advance Setting link to go to the Advance Setting page.

Click on Maintenance, click on Save All for permanently saved.

Click Restart.

Blue Thunder ADSL Router

2009-06-08T20:07:00.001-07:00

Product: Blue Thunder™ 4 Port ADSL Router Modem

To Activate: Plug in the Blue Thunder™ 4 Ports ADSL Router Modem to PC / Laptop.
Note: Make sure Network Cable, AC Adaptor and ADSL Broadband Line are connected to the Router. Switch ON the Router
To check for the IP address of the Network Adaptor, ensures that it is set to Obtain an IP address automatically.
Note: If you are unable to obtain the IP address, please restart your PC
Open Internet Explorer Browser and key in address http://192.168.1.1
Requires Authentication to login the Router Setting:
- Username: root
- Password: root
So did you guys suprise to see tha landing page for Blue Thunder? It’s the same as the ZTE modem configuration. If you guys familiar with ZTE, just do the same configuration as ZTE but if you guys don’t know who to do it, just go to ZTE Modem page to check the configuration.

BiPAC 5112S - ADSL Modem/Router

2009-06-08T20:06:00.002-07:00

Factory Default Settings
Login Username/Password:
a) Administrator (admin/password)
b) User (User/password)
Bridged Mode:
Pure Bridged LLC (RFC 1483 Bridged, LLC)
PCI/VCI: 0/35
Default IP: 192.168.1.254
DHCP Server: Enabled
NAT: Disabled

DEFAULT MODEM PASSWORD

2009-06-08T20:06:00.001-07:00

Default password for all TMNet Streamyx supported modem.

ZTE modem
- IP Address: 192.168.1.1
- Username: ADSL
  Password: expert03
- Username: ZXDSL
  Password: ZXDSL
- Username: admin
  Password: telekomst
KASDA modem:
- IP Address: 192.168.1.1
- Username: admin
  Password: telekomst
ArtNet modem:
- IP Address: 192.168.1.1
- Username: admin
  Password: telekomst
- Username: admin
  Password: admin
- Username: admin
  Password: password
Triz modem:
- IP Address: 192.168.1.1
- Username: admin
  Password: aaaaaaaa
Aztech modem:
- IP Address: 10.0.0.2 OR 192.168.1.1
- Username: admin
  Password: blank
- Username: admin
  Password: password
- Username: admin
  Password: admin
Billion modem:
- IP Address: 192.168.1.254
- Username: admin
  Password: password
Huawei modem:
- IP Address: 192.168.1.1
- Username: admin
  Password: admin
Hyundai HSE-220 Modem:
- IP Address: 192.168.1.1
- Username: ADSL
  Password: ADSL
- Username: admin
  Password: ADSL
- Username: root
  Password: root
Riger DB102:
- IP Address: 192.168.1.1
- Username: tmadmin
  Password: tmadmin
TP-LINK MODEM / ADSL2 / ROUTER:
- IP Address: 192.168.1.1
- Username: admin
  Password: admin

AZTECH DSL600 EU CONFIGURATION

2009-06-08T20:02:00.000-07:00

Type in http://192.168.1.1 and hit enter. If the page successfully loads, you will be shown with the screen in the image. Enter the Username and Password respectively and click Log In.

NOTE: Please refer to Default Modem Password

After logging in, you will be met with the Quick Start page. Enter the information below then click the Connect button and proceed to the next step.

User ID: username@streamyx
Password: your TMNet Streamyx password
Protocol: PPPoE
VPI: 0
VCI: 35

After clicking Connect, the screen will change and tell you that it is trying to connect with the settings you have specified. If everything works OK, you will be shown with the screen in the next step.

If the connection successfully established itself, you will be shown with this status page. Notice that the State column says Connected.

If the Connection State is connected, click the Save Settings link on the left side of the page. If the settings save successfully, it will notify you as in this image.

After saving your settings, click on the Reboot link from the menu on the left side of the page. After clicking the link, watch the modem’s status lights and wait for the PPP and DSL lights to go steady. Once it’s steady, you should be able to connect to the Internet.

ARTNET ADSL MODEM CONFIGURATION

2009-06-08T20:01:00.001-07:00

Type 192.168.1.1 at your Internet browser then insert the username and password as below:

Username: admin
Password: admin OR telekomst

Then at http://192.168.1.1/main.html, you will see quick setup click on it and you will see:

Quick Setup

This Quick Setup will guide you through the steps necessary to configure your ADSL router.

NOTE: All of original settings will be replaced by new settings after you finish these steps.

Select the check box below to scan the Internet connection automatically. It is recommended that there is no any PVC configured in your ADSL router before performing auto-scanning connection. Tick at Auto Scan Internet Connection (PVC).

Auto Scan Internet Connection

The scanning process will try to detect PPPoE or PPPoA connection provided by your ISP.

Example:

Scanning Internet connection...
PVC (0/35): detected as PPPoE LLC/SNAP

The ADSL router will configure 0/35 PPPoE LLC/SNAP as the Internet connection to your ISP.

Configure Internet Connection - WAN IP Settings

Enter information provided to you by your ISP to configure the WAN IP settings
Choose on the Obtain an IP address automatically because ur using dynamic IP
Tick on the Enable NAT

Configure Internet Connection - PPP User Name and Password

In order to establish the Internet connection, please enter PPP user name and password that your ISP has provided:

PPP User Name: username@streamyx
PPP Password: your TMNet Streamyx password

Note: Session established by; Choose Always On.

Configure LAN side Settings

Enter the ADSL router IP address and subnet mask for LAN interface and then enable DHCP server on LAN interface to provide IP address settings for your computers.

Primary IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0

Quick Setup - Summary

Make sure that the settings below match the settings provided by your ISP.

Internet (WAN) Configuration: VPI / VCI 0 / 35
Connection Type: PPPoE LLC/SNAP
Always On
NAT Enabled
WAN IP Address Automatically Assigned
Default Gateway Automatically Assigned
DNS Server Automatically Assigned
LAN Configuration: Primary LAN IP 192.168.1.1 / 255.255.255.0
Secondary LAN IP: 0.0.0.0 / 0.0.0.0
DHCP Server Off

Note: Click Finish to accept these settings and reboot the system. Click Back to make any modifications

Riger DB102 CONFIGURATION

2009-06-08T19:59:00.000-07:00

Go to http://192.168.1.1.

Username: tmadmin
Password: tmadmin

Then you will see this above page. Go and click at the WAN Tab and click at PPP.

Set the new interface as:

PPP interface = 0
ATM VC = aal5-0
Protocol = PPoE
Use DNS = enable
Security = PAP

Don’t forget to set your username as username@streamyx and also your TMNet Streamyx password. When done, click Submit.

Click on ATM VC and make sure interface are set as:

aal5-0 VPI = 0
VCI = 35
MUX = LLC
Max proto = 2

After that, click on Admin and then Commit and then Reboot Once it’s done you should check your Internet connectivity by loading your favorite website.

If you’re unable to go to 192.168.1.1, please make sure that your PC IP is in the range of 192.168.x.x.