Tips and Tricks for Audio Engineers

Can phantom power damage your microphones?

noreply@blogger.com (AVSTOMUSIC) — Fri, 25 May 2012 01:10:00 +0000

There have been a lot of speculations on this topic, so I felt responsible to give you my take on it, which comes from my experience as an audio engineer as well as a studio tech.

Phantom power or +48V DC seems like a high enough voltage to do some serious damage to microphones that don’t need it (like ribbons, dynamics and tube mics). Some people shut phantom power off when plugging and unplugging condenser microphones as well. The truth of the matter is that in reality the chances of damaging a condenser microphone because it was unplugged while phantom power was on, is absolutely none. Of course if you are used to shutting it off, every time you unplug a microphone, there’s nothing bad about it. For the 1 in 10 millions or so chance of it actually damaging a condenser mic keep following your routine.

How it actually works:

You don’t really need to know much of electronics to understand the following diagram:

Phantom power is usually 48V DC at very low current – (micro amps up to about 10 miliamps). It starts with the phantom power switch (far right on the diagram) then through a decoupling resistor R3 charging a capacitor C3, which acts like a filter, making sure there’s no ripple (ac component) to the +48V DC power. Notice how resistors R1 and R2 in a way split that power to two destinations - pins 2 and 3 of the XLR plug. So technically there’s 2 independent phantom powers running through your microphone cable. One between ground (pin1) and Hot (pin2) and the other between ground (pin1) and Cold (pin3), which automatically means the voltage difference between pins 2 and 3 is exactly 0 volts. In fact resistors R1 and R2 have an exact 1% tolerance to ensure both pin 2 and 3 carry exactly the same voltage – therefore no voltage difference between them. As you would notice on the microphone side the dynamic moving coil is connected between pins 2 and 3. Since the voltage between pins 2 and 3 is zero the coil would not even “know” there’s phantom power applied to it. Since the ground in any dynamic microphone is simply connected to the body of the mic and has nothing to do with the coil inside of it, the coil is not affected by the 48 Volts between ground and pin 2 nor the 48 volts between the ground and pin 3, unless we have a bad cable where the ground is shorted to either pin 2 or pin 3. A lot of microphones use Isolation transformers as shown on the diagram below. Transformers work on the principle of induction, which does not allow DC power to pass through it and in a way protects the moving coil from receiving phantom power even if the cable is shorted.

Most modern ribbon microphones have their ribbons isolated either electrically or with a transformer so phantom power could not damage them; in fact a lot of ribbon microphones designed in the past 10 year require +48V.

Tube microphones on the other hand have their own power supplies due to the high voltage and current demands of vacuum tubes and do not need phantom power either. In fact all outputs of tube microphones have isolating transformers, which stop the very high DC voltage (150V to 350V depending on the design) component of the tube audio output in order not to damage the microphone preamp. The same transformer obviously would protect the electronics of the microphone from phantom power as well. So tube microphones are OK with phantom powers as well, assuming there are no shorts in the XLR cable.

When it comes to dynamic mics. I’ve only come across a few models by “Heil Sound” out there that actually use phantom power. Surprisingly enough they actually work without phantom power, but +48V turns on an active circuit inside the microphone and makes the output level of it go higher. So if you have the choice of sending phantom power to a dynamic mic, don’t do it. Again the chances of damaging a dynamic mic with phantom power are very slim or rather none unless we have wiring problems.

The moral of the story is: Phantom power is generally harmless, even though it sounds very unpleasant while switched on or off and it could damage your speakers, headphones and more importantly your ears, if you mess with it while listening to the output of the microphone preamp. Having said that, your expensive microphones deserve good care and you shouldn’t risk damaging them by a freak coincidence and a 20-year-old shorted cable.

Here are some scenarios where phantom power could cause some damage:

1. Unbalanced electronics connected to a microphone input – For example an MP3 player or an output of a consumer wireless receiver, a laptop headphones output, etc. The unbalanced nature of those sources naturally shorts the Cold signal to ground, making +48V present on Its output between Hot (pin 2) and Ground (pin 1). In those cases it is possible to damage the output of the device but not necessarily. My iPod for example has seen plenty of phantom power on its outputs over the years (it wasn’t me sending it) and it never got damaged.

2. Sending Phantom Power to an old (prior to 1970 design) ribbon microphone without an isolating transformer, while using a bad cable, which has the ground (pin 1) shorted to pin 2 or pin 3 of the XLR. This is the one classic example why everybody says - do not send phantom power to ribbon microphones, but the chances of this “perfect storm” to happen are really not that big.

Theoretically, this scenario would damage a dynamic microphone too, but in reality the current of the phantom power is low enough so that even if it flows through the coil of a dynamic microphone it wouldn’t inflict any permanent damage to it, at least not in the first couple of minutes or so. R1 and R2 from the first diagram are limiting the current to maximum of 0.007 Amps or 7 miliamps (from ohms law: Current = Voltage/ Resistance) or Current in this case is 48volts divided by 6800 ohms = 0.007 Amps. Definitely not the best thing to do to your dynamic microphones, but at least they won’t blow up like ribbons would under the same conditions.

3. All those examples deal with having Phantom power present. The moment of switching Phantom Power ON is a whole different issue.

For example you should NEVER patch anything carrying phantom power on a TT or ¼ inch patchbay. The nature of these connectors and the fact that the Tip, Ring and Sleeve are physically lined up behind each other makes them short out and/or send Phantom power to all the wrong pins of the XLR on the other end of the microphone line, at the moment the cable is inserted in to the female patch point.

Besides damaging your microphones, Phantom power could damage some microphone preamps as well. In the above described case of patching Phantom power on patchbays and in some cases of simply plugging a condenser microphone to a line with already existing phantom power, from diagram number 1, C1 and C2 are 2 decoupling capacitors stopping phantom power from entering the first stage of the microphone preamp and damaging its own active components. In some microphone preamps where no input transformers are used, the initial surge of current from a microphone being plugged in, or from cross-patching using TRS plugs – C1 and C2 get charged to 48 volts, but the side connected to the input of the preamps draws some current through the input stage of that amplifier. Over time and repeatedly doing this, the active components of the first amplification stage (transistors or ICs) start to “ware out” and become noisier than the usual.

In conclusion: Most microphones designed in the last 30 years either require Phantom Power or don’t care about it, assuming no wiring problems exist. So using ribbon, dynamic, tube, wireless, and condenser microphones on the same board with a master Phantom Power ON at the same time is just fine. Simply watch out for those odd cases described above.

Stereo Compression

noreply@blogger.com (AVSTOMUSIC) — Fri, 11 May 2012 23:00:00 +0000

Since the title of this blog is “Tips and Tricks for Audio Engineers” here’s a tip on linking compressors in stereo mode. A lot of inexperienced engineers and some “experienced” ones too expect when they link 2 compressors in stereo mode for the left or the first one to become “The Master”. There are very few stereo compressors out on the market that truly link all of their controls when in stereo mode. The dBx166XL is one of them.

The more common linking is the side chain link. In this case 2 or more compressors are considered linked even though their individual controls still work independently so there is no "master". You would say, how are they linked if they are still independently controlled. Merging or linking the side chains of compressors makes all of them compress at the same time according to the highest gain reduction at any given time of any of the linked compressors. In other words you can link 2 compressors in a stereo pair and have one of them set to fast attack and fast release while the other is set to the slowest attack and the slowest release. The thresholds can be set at different values too, but whichever one of the 2 signals going through the 2 compressors ends up triggering one of the compressors (i.e. the signal crosses above the set threshold level for that channel) it will make not only that channel of the compressor react to it, but both channels simultaneously will reduce the gain with the exact amount. For example the channel with the fast attack and fast release may have a sustained bass notes going through it and if the threshold is set really high the bass may not even get compressed at all. On the other channel you may have a kick drum with the same peak level as the bass and threshold set really low so that every kick hit crosses way above the threshold. Because the attack of the kick compressor is set to the slowest possible setting for the given compressor, the kick will not trigger the compressor either, so both the bass and the kick will stay unaffected by the linked compressors. Lets say the drummer plays a slow cymbal roll which gets picked up by the outside kick mic, and even though the level of it is much lower than the kick itself, it is loud enough to cross above the low setting of the threshold on that channel of the compressor and because it is sustained it will trigger the compressor even with the slow attack setting and it will make it reduce the gain of the cymbal roll. At the same time because the side chains of the 2 compressors are linked it will also reduce the gain of the bass as well (probably not what you were going for). Every compressor will react differently in such a situation depending on the ratio and makeup setting as well as the attack and release time settings. The point is: Experiment, and figure things out on your own for every compressor you own. Don’t assume they all react the same. A lot of times you may find linking functions where the thresholds and/or makeup gain controls of the right/second compressor get overwritten by the settings of the first one while the attack and release controls may still be independent.

Channel Path Vs. Monitor Path

noreply@blogger.com (AVSTOMUSIC) — Sun, 18 Mar 2012 22:34:00 +0000

The Terms “Channel Path” and “Monitor Path” are used in audio engineering to describe the two paths any audio signal runs through in order to be recorded and heard. Usually channel path describes the source signal most likely starting with a microphone plugged in to a microphone preamplifier and ends at some kind of a recorder – most likely a multitrack recorder. The monitor path is the path through which we monitor what we are recording. In other words it starts with the return or the output signal of the recorder and it ends at your speakers or headphones – (not the artist’s headphones). The way audio consoles deal with both of those paths - we have two main types of mixers – “In-line” and “split”. Split consoles are easy to understand – lets say you have a vocal microphone plugged in to channel 16 and routed to your multitrack recorder input 16 – That’s your channel path. The output of your recorder on the other hand is connected to channel 1 of the same console. Channel 1 is now routed towards the speakers, which serves the function of a monitor path. So the console gets split by the engineer. He/she decides what modules of the console to be used as monitor paths and which other modules as channel paths. Inline consoles, also referred to as dual path consoles have both the channel path and the monitor path built in to the same module. Meaning you may have a vocal microphone plugged in to “channel” 16 going towards your multitrack recorder and probably being recorded on track number 16 while the output of track 16 is also connected to “channel” 16 of the same mixer (this time the monitor path of it) and controlled by a separate fader going towards the speakers for monitoring. If that sounds confusing – it is because of play of words, which is always the case in the audio industry. A lot of times the terms “module”, “channel”, “monitor”, “track”, “buss”, “sub”, “group”, “send”, “return”, and many more are misused, misinterpreted or simply interchanged. And not from the lack of knowledge – Audio gear manufacturers seem to be trying to confuse everybody on purpose. Even professional console companies like SSL and Neve seem to have an internal disagreement. SSL for example calls their multitrack busses – “groups”. On the same console you may also find a “VCA group” and a “software group” which are completely different things. Also most large format consoles, like the SSL 9000J in MIX Mode use their dedicated channel paths and NOT the monitor paths for monitoring. So if someone in the middle of a session asks: “Is the vocal on group 5?”, or “Is that bass on channel 13?” - the question itself would mean absolutely nothing, because of the existence of multiple “group 5s” each one with a completely different function, as well as the term channel a lot of times implies both channel path and monitor path at the same time and it is also somewhat interchangeable with the term “module”. After a few years of dealing with multiple recording consoles people get a sense of all that misused terminology and no longer find it strange that the inputs to Pro Tools for example on the patch-bay are labeled as “Multitrack Sends”. On the other hand a lot of manufacturers simply mislabel or are absolutely wrong with their concept. For example Tannoy, which is a well respected speaker manufacturer, labeled their input gain knob on their Reveal 6 active monitors as going from the range of “-10dBU/+4dBU”. Every audio engineer knows that professional Line level standard is +4dBu and NOT +4dBU, and if Tannoy meant consumer standard, then it is -10dBV. Let alone the fact that -10dBV input is a lot more sensitive than a +4dBu input, which means the label should have been +4/-10 and not -10/+4 because that means the knob would be attenuating your signal as you turn it clockwise, which is not the case on the “Reveal 6”. Not to mention the whole issue of the entire recording industry of Phase vs. Polarity. When it comes to channel path and monitor path it is up to the user to deal with every manufacturer’s crazy idea of the use of those two paths and terms. As long as we understand what their function is, and how to use the channel and the monitor path, audio gear manufacturers will continue to intentionally confuse their main consumers, as different companies will never agree on a standard terminology.

References:

Phase vs. Polarity - http://avstomusic.blogspot.com/search?updated-max=2011-08-16T13:12:00-07:00&max-results=15

Reveal 6 - http://www.amazon.com/Tannoy-Reveal-6D-Active-Monitor/dp/B000Z78BZO

Tannoy - http://www.tannoy.com/

SSL 9000J in Mix Mode - http://avstomusic.com/index.php?p=2_4

SSL - http://www.solid-state-logic.com/

Neve - http://www.ams-neve.com/Home/Home.aspx

Inline Consoles - http://answers.yahoo.com/question/index?qid=20091017130601AASBKju

Split Consoles - http://www.dilettantesdictionary.org/index.php?search=1&searchtxt=split%20console

Audio consoles/ Mixers- http://en.wikipedia.org/wiki/Mixing_console

Monitor Path - http://www.gearslutz.com/board/so-much-gear-so-little-time/462514-inline-split-dual-path-inline-consoles.html

Channel Path - http://www.gearslutz.com/board/so-much-gear-so-little-time/462514-inline-split-dual-path-inline-consoles.html

Multitrack recorder - http://en.wikipedia.org/wiki/Multitrack_recorder

Channel Path Vs. Monitor Path - http://books.google.com/books?id=ScUPniUxwL0C&pg=PA59&lpg=PA59&dq=channel+path+versus+monitor+path&source=bl&ots=cfahYxOe06&sig=q6ZxIZSqQruAX2_MKk-ZbtoPYCc&hl=en&sa=X&ei=p0pmT8LfKYPSiALLuOCiDw&ved=0CCEQ6AEwAA#v=onepage&q=channel%20path%20versus%20monitor%20path&f=false

Avstomusic Gear Tech. Specs Vs Good Sound

noreply@blogger.com (AVSTOMUSIC) — Fri, 02 Mar 2012 03:41:00 +0000

The eternal debate of technical specification of audio gear and the resulting quality of sound has been argued since the beginning of professional recordings. Unfortunately the nature of the topic always leaves the parties of the discussion in suspense, without getting to any conclusive, objective benchmarks. Here are some highlights to consider, which if not solving the dilemma, at least may give you an idea why the problem has no resolution.

I’m talking about how certain pieces of gear have great technical specifications in comparison to others and yet they may not sound as pleasing. On the other hand it is not uncommon to use some old “crappy” gear in the recording studio, which in comparison to modern technologies doesn’t measure up, and yet sometimes there’s something “sweet” about it’s sound or tone.

First lets look at transformers versus transformer-less gear. Due to the high DC (direct current) voltage requirements in vacuum tubes, which before 1955 were the heart of all electronic devices, transformers were widely used well in to the 60s and 70s. With the invention of the transistor, the use of transformers in audio gear became optional and today many manufacturers are going back to the roots, because transformers have some “magic” properties. Transformers work on a phenomenon called inductance. It is a process of transferring electromagnetic energy through the air or magnetic materials. The discrepancy with technical specification and the quality of sound of transformers comes from the fact that most measurements of audio equipment like Frequency response, Gain, THD (Total Harmonic Distortion) etc., are done using sine-wave signals:

Image retrieved from: http://upload.wikimedia.org/wikipedia/commons/7/77/Waveforms.svg

Due to the induction process transformers when tested with sine-waves tend to show pretty linear characteristics for a limited bandwidth. When transformers deal with square-waves:

Image retrieved from: http://upload.wikimedia.org/wikipedia/commons/7/77/Waveforms.svg

They tend to “distort” them and change the way they sound, due to damping or ringing and the above-mentioned limited bandwidth.

Image retrieved from: http://img708.imageshack.us/img708/5319/square10m.jpg

Technically that means transformers don’t have as good of a slew rate as transformer-less gear, which also automatically means a higher THD (Total Harmonic Distortion). In other words on paper some transformer gear may look horrible, but what it comes down to is how it sounds. When listening to music we don’t look at music charts or chords progression to get an idea of the music piece. Music is a real time art and certain types of harmonic distortion actually sound musical or ear pleasing. Just like with another endless debate of digital versus analog audio, some of the sweetness of certain pieces of audio equipment comes from it’s basic design’s shortcomings, and it’s inability to represent the source signal “accurately”.

If we evaluate modern transformer-less designs of audio gear using discrete transistors, or ICs, then the comparison would be more fair, in which case a poor S/N (signal to noise) ratio for example, simply means - poor signal to noise ratio.

In other words we cannot compare apples and oranges and pick one over the other simply based on their color for example. If taste is what we are concerned with, we have to try both the apple and the orange before we show a preference. Which brings me to the question: Which piece of audio gear is best for you? Which one tastes better - an orange or an apple? A good orange or an OK apple, an average orange or an excellent apple, a bad orange or a spoiled apple? And who says you’re deciding between those two for eating? What if you are making some hard-sider? I bet a spoiled apple would be your best choice.

Audio gear is so distinctive and subjective, that good sound engineers always use their own ears when deciding what to use or purchase.

References:

Transformers – A few Basics, Retrieved March 1 2012 from:

http://www.youtube.com/watch?v=UvHCQswnjEg&feature=related

Vacuum Tube, Retrieved March 1 2012 from:

http://en.wikipedia.org/wiki/Vacuum_tube#History_and_development

Transistor, Retrieved March 1 2012 from:

http://en.wikipedia.org/wiki/Transistor

Inductance, Retrieved March 1 2012 from:

http://en.wikipedia.org/wiki/Inductance

Total Harmonic Distortion, Retrieved March 1 2012 from:

http://en.wikipedia.org/wiki/Total_harmonic_distortion

Damping ringing in LC circuits, Retrieved March 1 2012 from:

http://www.siteswithstyle.com/VoltSecond/Damping_ringing_XFMRS/Damping_ringing_in_xfmrs.html

Slew Rate, Retrieved March 1 2012 from:

http://www.amplifier.cd/Tutorial/Slew_Rate/SlewRate.htm

Check Your Cables Before You Take Your Gear Apart!

noreply@blogger.com (AVSTOMUSIC) — Sun, 16 Oct 2011 22:36:00 +0000

Everyone in the recording industry talks about the sound of transformers, and vintage gear is still used in every major studio mainly because of the wonderful properties of tubes and audio transformers. Talking specifically about output balancing transformers, they tend to not only give the sound a particular coloration (most of the time a desired one), but they also create the perfect true servo balanced output only if the ground connection on the output jack (usually pin 1 of an XLR plug) is taken in consideration.

It is very important to use true balanced connections on devices that contain audio transformers on their inputs or outputs. And if an unbalanced connection is required (for some odd reason), make sure you ground the unused pin of that connection. For example:

A mic-pre like the Neve 1073 would have a transformer on it’s output. If the XLR cable used on the output of it looses let’s say pin 3 (the negative or inverted signal in a balanced connection) normally you would expect about 6dB of level loss. Not that big of a deal right?...Wrong! Not only would you lose useful signal, and decrease your S/N Ratio (Signal to Noise Ratio) but also the whole frequency response would change. You would lose most of the low frequencies depending on what kind of a gear you are going in to after the 1073. The reason for that is because the transformer on the output really would not have much to do with the ground of the device. When you lose one of the active pins on a balanced connection (pin 2 or 3 of the XLR) all you have left is one active pin and the ground. In a sense you would be trying to sort of bypass the transformer and “mess” with the audio before it hits the output transformer, because ground is usually present in the primary winding of an output transformer and not really connected to the secondary – (final output) of the transformer. That of course is not always the case but if you end up with a super week signal with no low end coming out of your Neve mic pre, check your cables first before you take it apart.

ProSoundWeb.com http://srforums.prosoundweb.com/index.php/t/41143/0/

Balanced audio Connections http://en.wikipedia.org/wiki/Balanced_audio

SNR http://searchnetworking.techtarget.com/definition/signal-to-noise-ratio

Primary winding http://www.thefreedictionary.com/primary+winding

Customer Satisfaction in the Recording Studio

noreply@blogger.com (AVSTOMUSIC) — Tue, 16 Aug 2011 20:12:00 +0000

-->

The clientele and the size of the business of any recording studio are always determined by the satisfaction of their clients. A lot of engineers, producers and studio owners don’t realize that the recording industry is not just product-oriented business, but a service industry as well; like a restaurant for example. Yes the quality of the food is very important, but the total atmosphere and the attitude of the waiter are just as important. As an engineer, I feel like the final quality of the mix for example is just as important as the process that delivered that final mix. Since music and the recording process are very subjective and not tangible, there are a lot of situations that remind me of the fable "The Emperor's New Clothes". For example an electric guitar track recorded through a $5,000 microphone will always sound better to the untrained ear if that person knew the price of the microphone, even if a $75 microphone is way more appropriate for the job. See the article “The Essential Microphones - The Shure SM57 & the Neumann U87” http://ezinearticles.com/?The-Essential-Microphones---The-Shure-SM57-and-the-Neumann-U87&id=1777297

At the very beginning of my career as an engineer I was fortunate enough to work with great engineers and producers. As an assistant engineer I’ve witnessed the following scenario in the studio on more than one occasion:

After 8 or 10 hours of working on a mix the engineer is pretty happy with the sound and ready to print the final mix and go home. Instead we find out that the record label executives, A&R, or the band’s managers are on their way to check on the progress of the song. Two minutes before they walk in the control room, the engineer takes the bass track and turns it way down, to a point where you can barely hear it. After the A&R guys heard the mix they all agreed “It’s perfect, except it needs more bass”. The engineer brings the level of the bass back where it used to be, and everyone approves the mix and goes home. Later he explained to me that if he hadn’t done that, we were all going to spend the entire night trying to find a flaw in the mix so that the A&R guys would feel like they contributed somehow to the great final product.

On many other occasions when working with an inexperienced producers, as an engineer I’m forced to play mind games. For example I might be asked to ad more effects on a vocal, when it’s obvious to me and everyone else in the studio that the vocals have too much effect already. In this case I would pretend I’m adjusting the effects while doing nothing, and magically the producer feels like the vocals sound so much better now.

The studio I worked for a few years ago had a few thousand dollars extra in their budget. The dilemma was whether to buy the latest model ribbon microphone, or a giant screen TV with Play Station and X-Box. Guess what, we ended up getting the game system. Having good microphones and gear is very important, but that only satisfies the engineer. The real paying clients in the studio are the artists and the record labels behind them. Getting them occupied while doing the tedious techy stuff in the recording process, turned out to be more lucrative then getting the shiny microphone. See article by “Record Productions” http://www.recordproduction.com/sanctum-sound.html

All those examples prove that client satisfaction in the recording studio includes the process of getting to the final product as well as the product itself. Many studios I’ve been to, don’t take that in consideration. They focus only on the technical aspect for the project, not realizing that even with a great sounding final product, they are providing a horrible service to their clients.

Time Management in the Recording Studio.

noreply@blogger.com (AVSTOMUSIC) — Wed, 03 Aug 2011 21:55:00 +0000

--> Managing your time in an efficient way when in the recording studio is the most important skill you may learn as a producer and an engineer. Almost every session I've worked on in my life has ended late with not quite everything scheduled done.

Make the most of your time in a recording studio: 10 great tips

written by: Alex Fraser; article published: year 2007, month 11

Two main reasons recording budgets always run short - poor time management, and personal conflicts between band members, engineers, producers, A&R. If you take both of those factors out, every record should always turn out as planned. The reality is that we can’t quite predict other people’s actions and avoid confrontation. With a little experience we can definitely foresee the amount of time needed for a particular task in the studio. What most producers usually don’t accommodate for in their scheduling is the time it takes to resolve the personal conflicts. We all tend to ignore the human factor in everything we do, but it is a very real condition that’s unavoidable. For better or worse we are all humans. Because of that human factor, a lot of times our ambitions are higher than what we are capable of doing. In general that’s a good thing, but when it comes to studio time, the opposite has proven to be more efficient. Don’t go in the studio with a huge plan for the day. Be well organized, but don’t try to schedule every second of the session. A well-rehearsed band can probably do six basic tracks in about six ours of recording time. The same band with the same songs on a different day might do only three songs in the same given time. That’s the reality of it when taken the human factor in consideration. So don’t plan on getting six tracks in six ours. At the same time studio time and tasks performed never have a linier relationship. If you can record six tracks in six hours that doesn’t mean you can record three tracks in three hours, nor does it mean you can do twelve tracks in twelve hours. Time management in the studio always comes down to preparation. Think of your session time as a robot that needs to run on autopilot. If you didn’t program it well at home it will crash and burn and there’s nothing you can do about it. It’s usually a fine line between preparation and setup time vs. session time. If you need to print scores or learn lyrics obviously that would be a part of your personal preparation you can do at home ahead of time. When it comes to the actual physical setup in the studio a lot of times that’s done right before the downbeat of the session or sometimes as a part of the session time. All those factors should be taken in consideration to achieve effective time management in the studio. The producer of the session should be the one responsible and act as the time manager, but a lot of times no one takes control and sessions run into a grinding halt, mainly because of a poor time management.
See also "Top 5 Recording studio tips" by Joe Shambro

Does Audio Cable Length Matter

noreply@blogger.com (AVSTOMUSIC) — Tue, 12 Jul 2011 11:14:00 +0000

The length of your cables does matter. Not because the signal gets delayed if it travels through a longer cable or because it might get phase-shifted compared to the same signal traveling through a much shorter cable. The effect of the wire and cable lengths in the recording studio are so insignificant to the delay of the signal that we can just ignore them. (it takes about 0.00089 seconds or almost 1ms (millisecond) for sound to travel 1 ft in air at sea level. In order to get your signal delayed by 1ms just by adding length to your cables, it would take you about 186 MILES of cable)

The length of the cable does matter though especially if we are talking about a guitar unbalanced cable. The impedance of the guitar is so high that the capacitance of the cable would definitely affect the high end of your signal. See Gene Dellasala's detailed article on RLC losses in a cable. Also Unbalanced connections are susceptible to magnetic and Radio Frequency interference so the longer the cable the better the chances are you'll end up with unwanted hum or radio or who knows what in your guitar signal.

If we are talking about balanced microphone cable the length matters for the same reasons as the guitar cable although balanced cables tend to reject magnetic interferences pretty well. The problem with the microphone signal is that the voltage of it is so low (in the micro Volt range - 1 micro Volt = 0.000001 Volts) that after amplifying it 40-50 dB or so it is very important that the cables pick up absolutely nothing on the way to the mic-pre input. Also I personally had the weird experience with the Sony "Solid Tube" Mic (more than once on 2 different mics) where I had a 3 ft "Mogami" mic cable coming out of the power supply straight in to my studio's mic panel on he wall, and I was picking up some radio station. First I lifted the ground on the power supply but it got worse. Then I changed the cable with a 15ft Mogami and the radio disappeared. Now I always use the longer cables on the "Solid Tube" until one day I had that same radio... I changed the cable back to the 3-footer and the radio was gone. Maybe just a coincident or some capacitance match or who knows what... My point is CABLE LENGTH MATTERS.

If we are talking about speaker cable, a lot of people have the miss-conception it's OK to run Speaker Cables as long as you want. It is both true and not. Speaker level has the highest voltage and the lowest impedance out of all signal levels used in a recording studio. In that sense it is safest to run the longest runs. On the other hand, because of it's super low impedance the resistance of the wire makes a big difference on the power at the other end. Depending on the speaker cable a 50 ft run, depending on the gage, may have a total of 2 to 4 Ohms of resistance. If your speaker's impedance is 4 ohms and your amplifier is rated to drive 100 watts over 4 ohms (assuming) the wire resistance is 0 ohms, you'll get your full 100 Watts. What happens when you put your speakers 50 ft away from the amp... the resistance of the cable gets added to the 4 ohms of impedance of the speaker for a total of 8 ohms. Now the same 100 Watt at 4 ohms amp has 8 ohms of load instead of 4 ohm giving us only 50 Watts. Power(Watts) = E squared divided by the Resistance (impedance) where E=Voltage which is constant in the above example. Note the use of resistance vs impedance and vice-versa. We use resistance when we are referring to DC circuits, and Impedance when talking about AC circuit - all audio signals are AC (Alternating Current)

See also the following blogs on this topic:

http:prosoundweb.com/index.php/t/29468/0///recforums.

http://www.seymourduncan.com/forum/showthread.php?t=190210
http://www.mylespaul.com/forums/squawk-box/11307-does-speaker-cable-length-matter-head-cab.html

Phase Vs. Polarity

noreply@blogger.com (AVSTOMUSIC) — Sat, 02 Jul 2011 21:42:00 +0000

Phase has to deal with timing and waveforms developing over time.

Polarity on the other hand has nothing to do with timing. It is purely a matter of direction of flow of electrical current.

You've probably heard the term "Out of Phase" or "180º Out of Phase" 99% of the time people use this term when they mean "Reversed Polarity" Almost every mic preamp or a console out there has a "Phase flip" switch, which is misleading. All that switch does, is reverse the polarity of the signal. Since it clearly has nothing to do with the timing of the signal it should not be associated with "Phase".

CORRECTING PHASE WITH REVERSING POLARITY.

Phase problems or issues occur every time we have two or more instances of one source of sound. For example…

A guitar miked with more than one microphone, or a direct signal from a bass and a split of that same bass going through a bass amp which we've miked, or a close-miked drum-set and a room mic picking up that same drim-set. In all of the above examples we have one source of sound and more than one physical location where we capture that sound. Considering the speed of sound in air (1125 ft/s) it makes sense that one of our instances of that source would run slightly behind the other - (timing differences equals phase differences). The effect of the wire and cable lengths in the recording studio are so insignificant to the delay of the signal that we can just ignore them. (it takes about 0.00089 seconds or almost 1ms (millisecond) for sound to travel 1 ft in air at sea level. In order to get your signal delayed by 1ms just by adding length to your cables it would take you about 186 MILES of cable)

So you have your two mics on your kick drum for example - (one inside and one outside of the drum) about 1 ft away from each other. The outside mic will pick up the sound of the beater hitting the head about 1ms later than the mic a foot closer to the beater. So considering the speed of sound again, frequencies around 1125 Hz may get a boost while frequencies around 562.5 Hz may get lost. If we reverse the polarity of one of the two mics in theory the frequencies around 562.5 should get a boost and the range around 1125 Hz should disappear. Yes and NO. If we work with pure sine waves that would be the case - Before we reverse the polarity of the mic 1025Hz sine wave would fall exactly 360 degrees shifted over the distance of 1 ft and double itself in amplitude, while 562.5Hz sine wave would shift exactly 180 degrees over 1ft, so it would cancele itself completely. But since we are dealing with a complex waves and not just a pure sine wave, plus the fact that the two mics are probably different models and they pick up the sound of the drum at different locations of the drum itself, the two signals would have different frequency content to begin with. So after we combine them together we get a third frequency content of the sound of the drum. By flipping the polarity of one of the mics we drastically change the combined frequency content but that doesn't mean we completely lost our 1kHz range. Depending on the drum the mics the positions and also the rest of the drum mics like over heads and rooms you may end up reversing the polarity of one or two mics so you can get the desired sound... There is no right or wrong way... Just experiment and trust your ears. Rule of thumb is If you have two mics that are close to each other - 6 inches or less and you would like to mic some kind of a low frequency source - bass amp kick drum, guitar amp etc. make sure the polarity on of both mics is the same. After summing or mixing two microphones that have timing/ phase differences in the sound they are picking up, we create what's called a "Comb Filter". By reversing the polarity of one of the microphones all we do is shift the frequencies that get boosted and the ones that get cancelled out. In either case we end up with a severe EQ curve. At this point It is just a matter of preference and overall desired sound.

Also see article by "Musician's Friend" on the same topic.