Voxilla VoIP Forum - Linksys (Sipura) VoIP Support Forum

Confused about Caller ID; SPA3102

MrKoen — Fri, 03 Jul 2009 23:03:17 GMT

Not totally sure from your story if you ran against the same issue as I did, but I managed to fix my problem. Might help you or others hitting this page through a search query. I am using the 3CX VOIP PBX. I have an analogue line connected through a Linksys SPA3102 ATA adapter to the 3CX PBX. For the configuration of this SPA3102 device I used the walkthrough at http://www.3cx.com/voip-gateways/linksys-3102.html . It works fine. However once configured I noticed the caller ID of an incoming call on the analogue line wasn't being passed on to the 3CX PBX, just the internal registration number (10001 in my case). I googled to look for an answer on this and found some people stating to raise the theshold value, others stating to update the firmware. None of all that worked with me. A simple setting that was overlooked in the tutorial did! Go to the PSTN line tab in the configuration pages of the Linksys SPA3102 device. Scroll down to the PSTN-To-VoIP Gateway Setup section. Here you will find an option PSTN CID For VoIP CID. Set this to yes, save your changes and voila. It worked here. I now nicely see the incomming caller ID on my 3CX connected VOIP clients.

How to bar certain calls from spa 3102

hwittenb — Fri, 03 Jul 2009 16:12:45 GMT

You can design a new dial plan string that only allows the dialing digits that you wish to allow and prohibits dialing of other numbers.

Read the "sticky" thread in this forum about "How do I craft a dial plan string" for the basics about dial plans.

PSTN-->VOIP

hwittenb — Thu, 02 Jul 2009 21:43:50 GMT

Quote:

Originally Posted by jwilczek (Post 130190)

I would like to take a SPA3102 at one location with an unused PSTN line and turn it to IP and at another location break it back out. I have read up on how to do this with 2 SPA3102's but I was wondering could I do it with a SPA901 VOIP phone

If by "break it back out" you mean talk on the call with the handset that is part of the SPA901 ip phone or initiate calls from the handset it should work just fine. I have not tested it that way nor seen a report of someone using a SPA901 but I believe the ip phone settings are similiar to the line settings in the Cisco/Linksys analog telephone adapters and the SPA3102's Line tab.

SPA9000 And Direct Ip Calling ????????????

grillovillegas — Thu, 02 Jul 2009 21:42:30 GMT

All sip ports are properly forwarded also RTP too

The thing is if i use any provider to make the call
everything goes fine.

But the problem is when i try to make the Direct IP call
it makes the call but then it gets disconnected and
it doesn't end the call on the other end.

The problem is only with spa9000 all the other devices
same setup and everything works fine with direct ip calling.

Thanks in advance.

New Linksys SPA Localization Wizard looking for beta testers

voxillazitouni — Thu, 02 Jul 2009 06:40:40 GMT

Cause Linksys branding is going to dissapear.. Cisco Small business will be the new brand.. It is not a bad strategy since cisco has a stronger brand reckognition as well as image.
Linksys started to go to high featured products and Cisco wanted to offer lower cost product.. That is what happend according to a Cisco executive with who I spoke yesterday..

Zitouni

ps Cisco Small business new branding

Mac User needs Help converting Wav to Srt

libertyforall1776 — Wed, 01 Jul 2009 22:57:05 GMT

What is the SRT file format? What does it stand for? These details can help locate a converter for you...

Also, try loading Windows on VMWare or Parallels on your Mac, and run the Windows Ringtone Generator:
https://www.myciscocommunity.com/docs/DOC-6672

How to Unlock SPA-2102 ?

libertyforall1776 — Wed, 01 Jul 2009 22:33:33 GMT

You can try the SPA2102 Recovery Tool:

https://www.myciscocommunity.com/ser...2102-5-2-5.zip

Current firmware is 5.2.5...

Sipura SPA2100 Hard Reset

libertyforall1776 — Wed, 01 Jul 2009 22:18:32 GMT

Try the SPA2100 Recovery Tool:
https://www.myciscocommunity.com/ser...100-3-3-14.zip

SPA2100 Firmware 3.3.11 out

libertyforall1776 — Wed, 01 Jul 2009 21:55:46 GMT

Ok, 3.3.14 is out -- looks like Cisco/Linksys is doing their BEST to make them difficult to find!

https://www.myciscocommunity.com/ser...0_03-03-14.zip

This is the new home for Cisco Small Business (Linksys VoIP) support:
https://www.myciscocommunity.com/com...mallbizsupport

Go here and search for spa2100...

Cisco SPA8800/SPA8000 Review?

libertyforall1776 — Wed, 01 Jul 2009 21:46:00 GMT

Anyone had the opportunity to deploy a Cisco SPA8800 so we can see a review? ;-) Looks like Linksys is now Cisco Small Business...

http://www.cisco.com/en/US/products/ps10446/index.html

How about the spa8000 too?:
http://www.cisco.com/en/US/products/ps10025/index.html

TIA!

SPA400 won't reset

Guns — Tue, 30 Jun 2009 16:25:41 GMT

Hi All,
I have an SPA 400 and recently upgraded the firmware to 1.1.2.2 and ever since I can't get it to reset.

The network no longer sees the devive, I can't access it directly or anything.
I have tried powering off, pressing the reset on powerup, holding the rest in for 30 second, holding in reset whilst powering up and have run out of options.

Does anyone have any idea how I can get my 400 back please?

Cheers
Guns

SPA3102 FXO Registration Problem

hwittenb — Mon, 29 Jun 2009 20:41:35 GMT

Quote:

Originally Posted by adda (Post 130124)

Meanwhile, do you know which VOIP providers do not require registration for outgoing calls?

I haven't seen a list. Some that do not require registration are CallCentric, Future-Nine, and the Betamax Companies (VoipStunt, VoipBuster, etc). As you know, authentication (userid, password, etc) is provided at the time of the call. Registration is, of course, required for an incoming call.

SPA962 Change Language to Portuguese

nuno.oliveira — Mon, 29 Jun 2009 14:03:19 GMT

Hello,

I've been upgraded the firmware of the phone to 6.1.5 version.

I've put the file in a TFTP Server. In the logs the phone download the file, but don't change the language of the Phone.

I've put this sintax serv=tftp://192.168.1.119/;d0=English;x0=enS_v101.xml;d1=Portuguese;x1=ptS_v 615.xml

What I need to do more?

Non-authoritative answer, Problem HEL!!!!!

dolphin2 — Sun, 28 Jun 2009 16:37:15 GMT

:confused:I’m having problem configuring DNS Server for Xp I have 2 nic cards in my pc 1 bean shere and 2 nic with, ‘m traing to unlocked PAP2 3.1.9LSC

IP:192.168.0.1
Sub Mask 255.255.255.0
And Preferred DNS 192.168.0.1
And when I dew de fallowing command in DOS prom these are the error I get

C:\>nslookup ls.tftp.vonage.net 192.168.0.1
Server: ls.tftp.vonage.net
Address: 192.168.0.1

Non-authoritative answer:
Name: ls.tftp.vonage.net
Address: 192.168.0.1

I have fallow the above post #5 with no look!! Any Help will be appreciated

Thanks:confused:

http://forum.voxilla.com/linksys-sipura-voip-support-forum/provision-pap2-21848.html

Removing dial tone

SirPrised — Sun, 28 Jun 2009 14:22:14 GMT

Quote:

Originally Posted by rizsher (Post 130079)

Is there a specific reason you'd want to remove the dialtone?.

Yes. I run an old mechanical Strowger rack as a hobby, connected up to the Cnet collectors network. We dial an '0' which of course removes the local DT and routes you off into what replicates the National and International networks i.e. the web, accessed in my case via the Linksys. As the initial DT is provided to the phone by the Strowger rack, it's not required after dialling an '0'. In fact it sounds really stupid ! I've now dropped it back to -60 and it's hardly noticeable.