May The Forge Be With You

MTFBWY Eps: 34 - New Quench Tank and Bad News...

2017-01-22T07:31:00.003-08:00

Well guys, I got a new quench tank, but I have to rebuild my forge... Ive lost too much refractory off the roof, so it doesnt hold the heat properly anymore. Not getting close to welding temps...

(click image for video!)

MTFBWY Eps: 33 - Ed's Knife & Grind Bowie

2017-01-15T07:34:00.001-08:00

Well, I got Ed's knife rough forged to shape, and I got a bunch of grinding done on my Bowie! I switched out to the Norton Blaze belts that I bought, and WOW! i love my grinder again haha!

(click image for video!)

MTFBWY Eps: 32 - Peter Wright 84lb Anvil!!!!

2017-01-15T07:32:00.002-08:00

Thanks to my friend Ed, i now have a proper anvil! its a 84lb Peter Wright anvil. I started cleaning it up, and once i get my hands on a wire wheel for my angle grinder, ill finish it up. I just got too antsy and wanted to try it out. having a proper anvil means that i can put in about half the work to get the same result! The anvil will put in as much as i am with the rebound it has! AWESOME! but now i have to build a few new hardy hole tools, as this anvil has a smaller one than my mild steel home-built one haha!

(click image for video!)

MTFBWY Eps: 31 - My Bowie pt1

2017-01-15T07:30:00.003-08:00

Well guys, as promised, here is part 1 of my bowie build!
Next weekend, ill put the final grind on it, and start building the guard and handles!

(click image for video!)

MTFBWY Eps: 30 - Brother's Bowie pt2

2017-01-15T07:28:00.005-08:00

Well guys, we didnt exactly plan on going out to the forge, but we did, and i forgot the camera inside... we just got so lost in time that i didnt even think about the camera haha!

(click image for video!)

MTFBWY Eps: 29 - Brother's Bowie pt1

2017-01-15T07:27:00.001-08:00

My brother is down for Christmas, so I got the forge all working really well! We started working on a custom leaf spring Bowie knife for him!

(click image for video!)

MTFBWY Eps: 28 - Welding The Sideskirts On!

2017-01-15T07:22:00.006-08:00

Hey guys, I needed to make and weld some sideskirts on the forge to help keep the heat in! I think it works pretty good!

(click image for video!)

MTFBWY Eps: 27 - Rearrange The Shop & Natural Gas?

2017-01-15T07:20:00.000-08:00

Well guys, I moved the forge so i could try to run it on natural gas, but that was a huge fail... I cleaned up the shop, leveled my anvil, and tried to make some tongs. I gotta seal up my forge better... losing too much heat.

Check these guys out!
Alec Steele
Tim @ Big Dog Forge
Jeff @ Darkmoon Metals
Tom @ Tom Chitwood Bladeworks

(click image for video!)

MTFBWY Eps: 26 - Top Secret Project pt2

2017-01-15T07:09:00.003-08:00

Well guys, after 3 weeks of resting my wrist, I got back into the shop. Last week's footage got about half edited before i got bored watching it, so i deleted it. I gotta follow this video style, instead of doing long running clips. ANYWAYS, i got a lot more done on the Top Secret Damascus Dagger project!

(click image for video!)

MTFBWY Eps: 25 - Top Secret Project pt1

2017-01-15T07:08:00.000-08:00

Well guys, I need to build something, but I have to keep it as quiet as i can haha! Here's part 1 of the top secret cable damacus build!

(click image for video!)

MTFBWY Eps: 24 - My First Cable Damascus!

2017-01-15T07:06:00.001-08:00

Well guys, I decided that I wanted to try some forge welding. After getting a piece of cable from a deck truck, I decided that my first piece made from pattern welded steel would be a cable damascus knife!

(click image for video!)

MTFBWY Eps: 23 - Truck Nuts for Jeff!

2017-01-15T07:04:00.003-08:00

Well guys, my buddy Jeff wanted some truck nuts made for his truck, I had a pile of these giant 2.75" nuts, so I decided to take on the challenge! He wanted them 'beat-up' looking, so I hope he likes them!

(click image for video!)

MTFBWY Eps: 22 - Holdfast & Hole Punch Tools

2017-01-15T07:02:00.005-08:00

Well guys, I made a holdfast to help with certain tasks, as well as finished my hole punching block. I cant wait to start using them! I need to make another set of tongs for bigger material and square material...

(click image for video!)

MTFBWY Eps: 21 - HH Hole Punch Tool pt1

2017-01-15T07:00:00.003-08:00

Well guys, punching holes in the tongs with my round hole in the anvil was tricky and messy, so I decided to start building a hole punch tool for my hardy hole!

(click image for video!)

MTFBWY Eps: 20 - Fix and Hang Hammers!

2017-01-14T21:06:00.002-08:00

Well guys, Seeing as I have to work tomorrow, I decided to just tidy and do some needed things in the shop, vs any forging this weekend. I picked up a new cross-peen hammer, which had a terrible handle fit (believe it or not, it was the better of the two that were at the store!) and a new handle for my favorite hammer! I also FINALLY got those straps attached so I could hang my hammers on the anvil!

(click image for video!)

MTFBWY Eps: 19 - TONGS!!! FINALLY!!!

2017-01-14T21:03:00.001-08:00

Well guys, I FINALLY was able to build a set of tongs! they arent anything pretty, but they will work and if i can forge easier and without dropping hot steel on the floor, then that's a win!

(click image for video!)

MTFBWY Eps: 18 - HD Bench Vise pt1

2017-01-14T21:01:00.001-08:00

Well guys, I cant afford a brand new big heavy duty vise, and all the used ones for sale are too small, so im building my own!

(click image for video!)

MTFBWY Eps: 17 - Hardy Hole Drawing Tool

2017-01-14T20:57:00.002-08:00

Jeff @ Darkmoon Metals

I actually made it through a project without stopping to start something else haha! The Hardy Hole Drawing Tool isnt pretty, but it works! I need to make more stuff and get better at symmetry. I am thinking that Im favoring one side more than the other, which is creating the lopsidedness of the stuff that i am making...

(click image for video!)

MTFBWY Eps: 16 - BIG Anvil, Tongs 2.0 & The Stretcher

2017-01-14T20:54:00.002-08:00

Well guys, I tried making a set of tongs, but they didnt turn out, so I started another set. This time, they are starting to work a little better. I need to stretch material better, so I saw the need for another tool! I also welded the hardy hole section onto my anvil, built the base, and got it higher off the ground! It is much easier to work with now, and Im not getting a sore back from hunching over anymore!

(click image for video!)

MTFBWY Eps: 15 - Prepping for Sunday (Bonus Video)

2017-01-14T20:51:00.000-08:00

Well guys, my buddy Mike should be coming over to smash some iron on sunday, so I decided to get a start on one of the projects ill be working on. Also Im going to be building a marking punch!

(click image for video!)

MTFBWY Eps: 14 - Forging A Hot Cut Tool!

2017-01-14T20:48:00.003-08:00

Well guys, as my first official forging project, I decided I needed a hot cut tool! My Next tool will either be a hold-down, or tongs. I REALLY need tongs...

(click image for video!)

MTFBWY Eps: 13 - Shop Cleanup

2017-01-14T20:46:00.000-08:00

Well guys, Im getting closer to having my forge ready to go! I got the intake system figured out, and now all I need is to take it all apart and use sealant on the threads!

(click image for video!)

MTFBWY Eps: 12 - Finish Wiring & New Anvil Head!

2017-01-14T20:43:00.002-08:00

Hey guys, I finally got the West Bank lighting done, now all I have to do to totally finish the wiring is pigtail the 2 outlets. Anyways, I went to the local scrap yard today, and picked up a good chunk of 2.75" Square stock, weighing 27lbs to use as my new anvil head! i gotta build the base for it, but I am getting closer every weekend to being able to forge stuff! Very excited!

(click image for video!)

MTFBWY Eps: 11 - Grinding Swivel Seat Parts!

2017-01-14T20:37:00.004-08:00

Well guys, I need a stool for the grinding bench, so i decided to make one. Ive gotta clean up the parts so I can then weld them!

(click image for video!)

MTFBWY Eps: 10 - Shop Wiring

2017-01-11T21:10:00.005-08:00

Well guys, today I got the East-Bank lighting wired up and working, and I also got the 4 East wall outlets wired up. I popped open the fuse panel to see what was going on inside, and turns out I didnt even have to buy any breakers! SCORE!

(click image for video!)