90cm 36 inch antenna and 75cm 30 inch antenna on SALE!!!

2008-07-13T11:54:17-07:00

WS9036 90cm satellite dishes on sale

Get 2 of the best 90cm satellite dish on the market for only

$89.99^*

That's almost $50.00 off. You can't even get it on EBay for that low. Add it to your cart by clicking here

Get 2 of our 75cm antennas for only

$69.99^*

That's almost $30.00 off. You can't even get it on EBay for that low. Add it to your cart by clicking here

^{*Offer expires
July7/31/2008}

New Dish Motor | Satellite Dish Motor SG6000 Satellite Motor

2008-06-19T19:23:19-07:00

DiSEqC 1.2 HH Dish Motor Model SG-6000

Why not get the BEST?

Superior Design & Stable Mounting System For Dishes As Large As 120cm (4ft)

Features:

Fits dishes up to 1.2m
Supplied with 42mm mounting tube to allow compatibility with the most popular type of dishes including the Winegard DS2076 dish antenna
Larger oversized mounting bracket helps with wind resistance
1-year manufacturers warranty
DiSEqC 1.2 Compatible
USALS Compatible
Everything controlled via 1 coaxial cable
Ultra low noise
Goto X function
LED Power Indicator
East/West movement button on motor
Degree indicator on shaft
Mostly steel gears except for shaft gear
Pressure treated plastic
Hardware Reset button to to allow you to easily reset the motor with a quick touch of a button

Most Stable Dish Motor On The Market... Your Best Choice In HH Dish Mounts...

Parts that are included in y our SG6000 Motor

SG-6000 - Most reliable positioner on the market today!

Do I need to install a separate power line to connect to the automatic HH dish motor mount?

No. The motor gets powered by the receiver. The receiver provides power to turn the LNB on and to switch polarity. The motor consumes the same power through the coaxial cable that runs from the receiver to the LNBF.

How do I wire up the SG-6000 Dish Motor?

Simply run the coaxial cable to your satellite dish motor, then from the HH dish motor run a 3 or 4 foot coaxial cable to the LNBF.

Do I need to manually turn the dish every time I change channels?

No. This is an automatic satellite dish motor. Once it's installed properly and your receiver is programmed with the locations of the satellites, every time you change channels, the receiver sends DiSEqC commands to the satellite motor to tell it to move and stop at a certain location where the satellite signal is broadcasting from.

Where can I find out what channels are available free to air?

There are many free to air DVB channels available in North America on satellites such as Galaxy 10R, AMC4, IA5, AMC3, etc. There are channels from the USA and from around the world. See http://www.lyngsat.com/america.shtml for a complete listing of what is available. Anything with an F designation is FREE TO AIR.

How many receivers can control a FTA dish motor?

Since a dish motor is designed as a hobby item, only one FTA free to air receiver can control the positioning of the motor. However, if you use a dual LNB or a quad LNB you can install multiple receivers, but each receiver can only watch the programming broadcasted from that particular satellite.

Do I have to be watching the same thing on all receivers if I use a dual LNB or quad LNB?

No. You don't have to watch the same programming, but you do have to watch a channel that is broadcasting from that particular satellite that your motor is pointing to. Keep in mind that only your main USALS or DiSEqC1.2 compatible FTA satellite receiver can control the Free To Air dish motor.

Where Do I install an FTA DiSEqC Switch:

Typically, when you use a quad polar LNB like the Invacom QPH031 you want to use a 2X1 or 4X1 DiSEqC switch after the motor. Basically, here is a quick rundown:

Run RG6 cable from your receiver to HH motor.

Run RG6 cable from HH motor to "Receiver" port on DiSEqC switch.

Run RG6 from ports on DiSEqC switch to Linear and Circular ports on the LNB.

Where to install DiSEqC HH Dish Motor Mount:

When you want to install an HH Motor, do a thorough site survey to ensure the proper location to install. First, scratch off the roof unless you have a flat roof and you want to use a non-penetrating roof mount. The best place to install a Free To Air HH Motor is on the ground on a pole. Go to The Home Depot and get a 2" pole. Drive it into the ground about 2 1/2 and make sure to use a pole level to make sure that the pole is 100% level.

Make sure & purchase a SF95 satellite signal finder / meter because it will help you guide your motor to the true south azimuth location. The meter will go off every time you get a satellite signal, so, when you keep on turning the motor, if the meter keeps going off, you know you have properly aligned the dish to the satellite arc. If not, you may need to keep adjusting for the proper azimuth. (Read the installation instruction guide)

www.Galaxy-Marketing.com Satellite Blog & News