Do it yourself Inkjet and Laser Printer Repair

Error E000677 0080 canon IR3220

2010-02-15T22:58:00.000-08:00

imageRUNNER iR C3220

when i try to print anything from my PC on the IR c3220N, some errors appear. Perhaps you got the same error like me.

solution:

Error E677 0080- occurs when sending print jobs to any printer on the network that has an imagePASS C1 or C2 attached to it.

1. Verify the copier and the imagePASS C1/C2 have the latest system software installed.

2. Verify that all posted patches for the RIP (either the imagePASS C1 or C2) have been installed.

3. Try re seating the Open Interface Board in the copier.

4. Try re seating the interface cable.

5. Try change from the PCL print driver to the PS print driver.

**also check the cable between the ImagePass C1/C2 and the Reader unit
if u have a C1 image Pass software should be v 2.1/ there is also a patch when using Microsoft PowerPoint .

also the iRC 3220 should have Firmware- v90.03

Canon PIXMA MP150 service manual‎

2010-02-14T20:23:00.000-08:00

Canon Pixma MP150 Error Code

E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

Canon GP200- GP215 Error code

2010-01-28T06:27:00.000-08:00

Eror Code	Solution
E000 E000	Fusing unit not heating up
E001 E001	Fusing unit overheating
E002 E002	Fusing unit not heating up
E003 E003	Fusing unit not heating up Unit sekering not heat
E007 E007	Fusing film damaged or out of position
E010 E010	Main motor lock
E030 E030	Counter error
E031 E031	Counter error at one option
E032 E032	Electronic counter error
E051 E051	Horizontal registration home position not found
E064 E064	High voltage drive board abnormal output
E100 E100	BD error
E110 E110	Polygonal mirror motor not picking up speed
E190 E190	RAM error
E191 E191	Communication lost between the main board and the power supply
E202 E202	Scanner home position not found
E203 E203
E204 E204
E210 E210	Lens home position not found
E212 E212	Lens home position not found
E220 E220	Exposure lamp blown or bad contact
E240 E240	Main board
E243 E243	Operation panel
E261 E261	Main power supply or Main PCB
E301 E301	Exposure intensity out of range
E400 E400	ADF control board problem
E401 E401	DF paper feed motor lock
E402 E402	DF transport error
E403 E403	DF paper transport error
E404 E404	DF paper exit
E411 E411	DF sensors problem
E422 E422	Copier to DF-F1 communication lost
E710 E710	Main board
E711 E711	Main board
E712 E712	Paper feed error
E716 E716	Paper feed unit error
E717 E717	Communication to the copier controller is lost
E800 E800	Auto shut-off relay malfunction
E803 E803	Power supply output out of range
E901 E901	Paper feed unit PCB malfunction

Error code E000733-0001 canon IR2200

2010-01-28T06:04:00.000-08:00

E733-0001 means a fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB.

Main cause: The connector has poor connection. The DC controller PCB is faulty.

Solution:
Verify the connection between the connector J1015 on the main controller PCB and the conductor J316 on the DC controlled PCB is normal.
Correct the connection if necessary.

The connection is correct: Replace the DC controller PCB.

error code 602-0003 IR5000

2010-01-28T05:50:00.000-08:00

E602

1) Are the connection and the cable of the connector (J1017) on the main controller PCB and the connector (J1551) on the hard disk drive normal? NO: Correct the cable connection.Hard disk drive (HDD), Main controller PCB
2) Try replacing the hard disk drive and downloading the system software.Is the problem corrected?
YES: End. NO: Replace the main controller PCB.

3) HDD unit.
Remove the rear upper cover and the reader rear cover. Remove the three screws, and detach the cover, Remove the two screws and disconnect the two connectors then, remove the HDD unit. Remove the six screws and detach the HDD When mounting the HDD unit,be sure that the flat cable is under the plastic sheet of the HDD upper case.

Solution 1# :
It can be a Sector Problem ,to resolve it just press 1&9 keys at the same time the machine started the HD Diagonose and it repared the sector error without replacing the HDD .

Solution 2# :
try to go in to disc check service mode to clear the sectors ,this should work if it doesnt you will need to replace the hard drive .

Solution 3# :
Try HD clear & then HD check for every sector in service mode. Then try to upgrade system software;If nothing works change hard disk ,format & install system software.

Epson Printer Error Codes for EPSON 7600 - EPSON 9600

2010-01-04T00:28:00.000-08:00

Here are some basic EPSON printer errors for the EPSON 7600 & 9600 series.
LCD Panel Messages:
0002 CR pass count reaches the limit Perform Maintenance Mode 2
Perform Maintenance Mode 2 [CLEAR COUNTERS / CR MOTOR
0008 RTC backup battery is empty
Install the battery and perform Maintenance Mode 2
0020 The number of shots (per nozzle) reaches the limit
Perform Maintenance Mode 2 [CLEAR COUNTERS / CLEANER]

0040 Pump motor operation count reaches the limit
Perform Maintenance Mode 2[CLEAR COUNTERS / CLEANER]
0080 Date is not specified
Perform Maintenance Mode 2[CLEAR COUNTERS / CLEANER]
0100 RTC backup battery drops
(Wait for a while) *2“If the same message appears again, replace the RTC backup battery and performMaintenance Mode 2 [CLEAR COUNTERS / RTC].”
0088 RTC backup battery is not installed
Install the battery and perform Maintenance Mode 2[CLEAR COUNTERS / CLEANER]

RESET ERROR CODE CANON MP145-MP150-MP160

2010-01-04T00:16:00.000-08:00

E2-2 = No paper (ASF)

E3-3 = Paper jam

E4 = No ink

E5-5 = The ink cartridges are not installed or a non-supported ink cartridge
is installed, or the ink cartridges are not installed properly

E8 = Waste ink absorber full, or platen waste ink absorber full

E9 = The connected digital camera / video camera does not support Camera
Direct Printing

E14 = The Ink cartridges whose destination are wrong

E15 = Ink cartridge is not installed E16 - Ink remaining is unknown

E16 -E19 = Failed to scan head alignment sheet

E22 = Carriage error

E23 = Paper feed error

E24 = Purge unit error

E25 = ASF(cam) sensor error

E26 = Internal temperature rise error

E27 = Waste ink absorber full or platen waste ink absorber full

E28 = Ink cartridge temperature rise error -

E29 = EEPROM error

E33 = Paper feed position error

E35 15 = USB Host VBUD overcurrent error - USB

E37 17 = Abnormal motor driver error

E40 20 = Other hardware error

E42 22 = Scanner error

Canon error codes

2010-01-04T00:09:00.000-08:00

BRAND MODEL ERROR CODE MOST LIKELY CAUSE
CANON 155 E0 The fusing unit does not heat up
CANON 155 E1 The sensor motor or sensor, the DC controller on the main board DC controller
CANON 155 E2 The copyboard position sensor
CANON 155 E4 Main motor, Main motor PCB, DC controller
CANON 155 E5 Lens home position error
CANON 155 E6 Exposure lamp control PCB, light intensity error, DC controller
CANON 155 E7 Main motor PCB, DC controller
CANON 155 E8 Counter error
CANON 155 E9 AC drive board, DC controller
CANON 155 EC Copy board drive lock
CANON 155 ED Operation panel
CANON 155 EE Main motor drive board, DC drive board
CANON FC330 E0 The fusing unit does not heat up
CANON FC330 E1 Fusing film damaged or out of position
CANON FC330 E2 Copy board drive lock or home position error
CANON FC330 E6 Blown exposure lamp or exposure lamp terminals bad contact
CANON 720, 740, 750, 770 C Fusing film damaged or out of position the machine tries to compensate
CANON 720, 740, 750, 770 H Fusing unit overheating
CANON 720, 740, 750, 770 E0 The machine was switched OFF and ON after one of the E00X error codes
CANON 720, 740, 750, 770 E000 Bad thermistor, thermofuse, fusing element, triac or power supply
CANON 720, 740, 750, 770 E001 Bad thermistor, triac or power supply
CANON 720, 740, 750, 770 E002 bad thermistor, thermofuse, fusing element, triac or power supply
CANON 720, 740, 750, 770 E003 bad thermistor, thermofuse, fusing element, triac or power supply
CANON 720, 740, 750, 770 E007 fusing film damaged or out of position
CANON 720, 740, 750, 770 E010 main motor lock, DC power supply
CANON 720, 740, 750, 770 E064 Main power supply or Main PCB
CANON 720, 740, 750, 770 E202 scanner home position not found
CANON 720, 740, 750, 770 E210 lens home position not found
CANON 720, 740, 750, 770 E220 exposure lamp, exposure control PCB, light intensity error, main PCB
CANON 720, 740, 750, 770 E240 DC power source controller or main power supply
CANON 720, 740, 750, 770 E261 frequency error caused by the main power supply or the power outlet
CANON 720, 740, 750, 770 E803 main board, main power supply or fusing lamp defective
CANON NP1010, NP1020 E000 Bad thermistor, thermofuse, fusing element, triac or power supply
CANON NP1010, NP1020 E001 Bad thermistor, triac or power supply
CANON NP1010, NP1020 E010 main motor lock, main motor rotation sensor,main board
CANON NP1010, NP1020 E210 lens or scanner home position not found
CANON 2020, 2120 E000 cuptorul nu se incalzeste
CANON 2020, 2120 E001 Bad thermistor, triac, SSR or power supply
CANON 2020, 2120 E030 Counter error
CANON 2020, 2120 E202 scanner home position not found
CANON 2020, 2120 E210 lens home position not found
CANON 2020, 2120 E400 ADF problem
CANON 2020, 2120 00-53 Sorter communication down
CANON 2020, 2120 E710 main board
CANON 3030, 3050 E000 Fusing unit not heating up
CANON 3030, 3050 E001 Fusing unit overheating
CANON 3030, 3050 E002 Fusing unit not heating up
CANON 3030, 3050 E003 Fusing unit not heating up
CANON 3030, 3050 E004 SSR or exposure lamp board
CANON 3030, 3050 E010 main motor lock, main motor rotation sensor,main board
CANON 3030, 3050 E022 development unit replacement error
CANON 3030, 3050 E030 Counter error
CANON 3030, 3050 E202 scanner home position not found
CANON 3030, 3050 E204 scanner home position not found
CANON 3030, 3050 E210 lens home position not found
CANON 3030, 3050 E220 exposure lamp blown or bad contact
CANON 3030, 3050 E400 ADF control board problem
CANON 3030, 3050 E401 DF paper feed motor lock
CANON 3030, 3050 E402 DF transport error
CANON 3030, 3050 E403 DF paper transport error
CANON 3030, 3050 E404 DF paper exit
CANON 3030, 3050 E411 DF sensors problem
CANON 3030, 3050 E500 Sorter control board
CANON 3030, 3050 E510 Sorter paper transport error
CANON 3030, 3050 E512 Sorter first motor lock
CANON 3030, 3050 E514 Sorter second motor lock
CANON 3030, 3050 E520 Stacker motor overloaded
CANON 3030, 3050 E530 Sorter V motor lock
CANON 3030, 3050 E531 Stapler motor overloaded
CANON 3030, 3050 E535 Sorter V motor lock
CANON 3030, 3050 E540 lateral movement motor lock
CANON 3030, 3050 E541 lateral movement motor lock
CANON 3030, 3050 E710 main board failure
CANON 3030, 3050 E711 main board failure
CANON 3030, 3050 E712 main board failure
CANON 3030, 3050 E800 emergency shut-off relay
CANON 3325, 3825 E000 Fusing unit not heating up
CANON 3325, 3825 E001 Fusing unit overheating
CANON 3325, 3825 E002 Fusing unit not heating up
CANON 3325, 3825 E003 Fusing unit not heating up
CANON 3325, 3825 E004 SSR or exposure lamp board
CANON 3325, 3825 E010 main motor lock, main motor rotation sensor,main board
CANON 3325, 3825 E022 development unit replacement error
CANON 3325, 3825 E030 Counter error
CANON 3325, 3825 E202 scanner home position not found
CANON 3325, 3825 E204 scanner home position not found
CANON 3325, 3825 E210 lens home position not found
CANON 3325, 3825 E220 exposure lamp blown or bad contact
CANON 3325, 3825 E400 ADF control board problem
CANON 3325, 3825 E401 DF paper feed motor lock
CANON 3325, 3825 E402 DF transport error
CANON 3325, 3825 E403 DF paper transport error
CANON 3325, 3825 E404 DF paper exit
CANON 3325, 3825 E411 DF sensors problem
CANON 3325, 3825 E500 Sorter control board
CANON 3325, 3825 E510 Sorter paper transport error
CANON 3325, 3825 E512 Sorter first motor lock
CANON 3325, 3825 E514 Sorter second motor lock
CANON 3325, 3825 E520 Stacker motor overloaded
CANON 3325, 3825 E530 Sorter V motor lock
CANON 3325, 3825 E531 Stapler motor overloaded
CANON 3325, 3825 E535 Sorter V motor lock
CANON 3325, 3825 E540 lateral movement motor lock
CANON 3325, 3825 E541 lateral movement motor lock
CANON 3325, 3825 E710 main board failure
CANON 3325, 3825 E711 main board failure
CANON 3325, 3825 E712 main board failure
CANON 3325, 3825 E800 emergency shut-off relay
CANON 4050, 4080 E000 Fusing unit not heating up
CANON 4050, 4080 E001 Fusing unit overheating
CANON 4050, 4080 E002 Fusing unit not heating up
CANON 4050, 4080 E003 Fusing unit not heating up
CANON 4050, 4080 E004 SSR or exposure lamp board
CANON 4050, 4080 E010 main motor lock, main motor rotation sensor,main board
CANON 4050, 4080 E022 development unit replacement error
CANON 4050, 4080 E030 Counter error
CANON 4050, 4080 E080 color interface problem
CANON 4050, 4080 E081 vertical transport motor overload
CANON 4050, 4080 E082 horizontal transport motor overload
CANON 4050, 4080 E084 color unit sensor
CANON 4050, 4080 E085 color unit position error
CANON 4050, 4080 E086 color unit position error
CANON 4050, 4080 E089 color unit position error
CANON 4050, 4080 E100 laser error
CANON 4050, 4080 E110 polygonal mirror motor not picking up speed
CANON 4050, 4080 E202 scanner home position not found
CANON 4050, 4080 E204 scanner home position not found
CANON 4050, 4080 E210 lens home position not found
CANON 4050, 4080 E220 exposure lamp blown or bad contact
CANON 4050, 4080 E223 color filter motor lock
CANON 4050, 4080 E240 main board
CANON 4050, 4080 E400 ADF control board problem
CANON 4050, 4080 E401 DF paper feed motor lock
CANON 4050, 4080 E402 DF transport error
CANON 4050, 4080 E403 DF paper transport error
CANON 4050, 4080 E404 DF paper exit
CANON 4050, 4080 E411 DF sensors problem
CANON 4050, 4080 E500 Sorter control board
CANON 4050, 4080 E510 Sorter paper transport error
CANON 4050, 4080 E512 Sorter first motor lock
CANON 4050, 4080 E514 Sorter second motor lock
CANON 4050, 4080 E520 Stacker motor overloaded
CANON 4050, 4080 E530 Sorter V motor lock
CANON 4050, 4080 E531 Stapler motor overloaded
CANON 4050, 4080 E535 Sorter V motor lock
CANON 4050, 4080 E540 lateral movement motor lock
CANON 4050, 4080 E541 lateral movement motor lock
CANON 4050, 4080 E660 IC card malfunction
CANON 4050, 4080 E710 main board failure
CANON 4050, 4080 E711 main board failure
CANON 4050, 4080 E712 main board failure
CANON 4050, 4080 E714 main board failure
CANON 4050, 4080 E800 emergency shut-off relay
CANON 6030 E000 Fusing unit not heating up
CANON 6030 E001 Fusing unit overheating
CANON 6030 E002 Fusing unit not heating up
CANON 6030 E003 Fusing unit not heating up
CANON 6030 E004 SSR or exposure lamp board
CANON 6030 E010 main motor lock, main motor rotation sensor,main board
CANON 6030 E022 development unit replacement error
CANON 6030 E030 B&W counter error
CANON 6030 E031 Color counter error
CANON 6030 E064 AC drive board problem
CANON 6030 E065 AC drive board problem
CANON 6030 E202 scanner home position not found
CANON 6030 E203 scanner home position not found
CANON 6030 E204 scanner home position not found
CANON 6030 E210 lens home position not found
CANON 6030 E212 lens home position not found
CANON 6030 E220 exposure lamp blown or bad contact
CANON 6030 E224 blank shutter not working
CANON 6030 E240 main board
CANON 6030 E244 main board to AC drive communication problem
CANON 6030 E400 ADF control board problem
CANON 6030 E401 DF paper feed motor lock
CANON 6030 E402 DF transport error
CANON 6030 E403 DF paper transport error
CANON 6030 E404 DF paper exit
CANON 6030 E411 DF sensors problem
CANON 6030 E500 Sorter control board
CANON 6030 E510 Sorter paper transport error
CANON 6030 E512 Sorter first motor lock
CANON 6030 E530 Stapler motor overloaded
CANON 6030 E531 Stapler motor overloaded
CANON 6030 E540 lateral movement motor lock
CANON 6030 E541 lateral movement motor lock
CANON 6030 E710 main board failure
CANON 6030 E711 main board failure
CANON 6030 E712 paper feed error
CANON 6030 E716 paper tray error
CANON 6030 E800 Auto shut-off relay malfunction
CANON 6030 E901 Paper feed unit electronic board
CANON 6030 E902 Paper feed unit home position error
CANON 6050, 6650, 8070, 8570 E000 Fusing unit not heating up
CANON 6050, 6650, 8070, 8570 E001 Fusing unit overheating
CANON 6050, 6650, 8070, 8570 E002 Fusing unit not heating up
CANON 6050, 6650, 8070, 8570 E003 Fusing unit not heating up
CANON 6050, 6650, 8070, 8570 E004 SSR or exposure lamp board
CANON 6050, 6650, 8070, 8570 E010 main motor lock, main motor rotation sensor,main board
CANON 6050, 6650, 8070, 8570 E011 main drive lock, one of the motors
CANON 6050, 6650, 8070, 8570 E013 used toner transport jammed
CANON 6050, 6650, 8070, 8570 E014 pick-up motor lock
CANON 6050, 6650, 8070, 8570 E020 black toner supply mechanism malfunction
CANON 6050, 6650, 8070, 8570 E030 Counter error
CANON 6050, 6650, 8070, 8570 E031 counter error at one option
CANON 6050, 6650, 8070, 8570 E050 duplex malfunction
CANON 6050, 6650, 8070, 8570 E051 duplex malfunction
CANON 6050, 6650, 8070, 8570 E202 scanner home position not found
CANON 6050, 6650, 8070, 8570 E203 scanner home position not found
CANON 6050, 6650, 8070, 8570 E204 scanner home position not found
CANON 6050, 6650, 8070, 8570 E210 lens home position not found
CANON 6050, 6650, 8070, 8570 E212 lens home position not found
CANON 6050, 6650, 8070, 8570 E240 main board failure
CANON 6050, 6650, 8070, 8570 E243 Operation panel
CANON 6050, 6650, 8070, 8570 E710 power supply error
CANON 6050, 6650, 8070, 8570 E711 power supply error
CANON 6050, 6650, 8070, 8570 E500 Sorter control board
CANON 6050, 6650, 8070, 8570 E510 Sorter paper transport error
CANON 6050, 6650, 8070, 8570 E512 Sorter first motor lock
CANON 6050, 6650, 8070, 8570 E530 Stapler motor overloaded
CANON 6050, 6650, 8070, 8570 E531 Stapler motor overloaded
CANON 6050, 6650, 8070, 8570 E801 thermistor, fusing unit, power supply, main board
CANON 6050, 6650, 8070, 8570 E802 power supply or main board error
CANON 6317 E000 Fusing unit not heating up
CANON 6317 E001 Fusing unit overheating
CANON 6317 E002 Fusing unit not heating up
CANON 6317 E003 Fusing unit not heating up
CANON 6317 E004 SSR or exposure lamp board
CANON 6317 E010 main motor lock, main motor rotation sensor,main board
CANON 6317 E030 counter error
CANON 6317 E202 scanner home position not found
CANON 6317 E208 mirrors home position not found
CANON 6317 E210 lens home position not found
CANON 6317 E220 exposure lamp blown or bad contact
CANON 6317 E245 main board
CANON 6317 E261 Main power supply or Main PCB
CANON 6317 E400 communication lost between copier and ADF
CANON 6317 E500 communication lost between copier and sorter
CANON 6317 E802 Main switch, main power supply
CANON GP200, GP215 E000 Fusing unit not heating up
CANON GP200, GP215 E001 Fusing unit overheating
CANON GP200, GP215 E002 Fusing unit not heating up
CANON GP200, GP215 E003 Fusing unit not heating up
CANON GP200, GP215 E007 fusing film damaged or out of position
CANON GP200, GP215 E010 main motor lock
CANON GP200, GP215 E030 counter error
CANON GP200, GP215 E031 counter error at one option
CANON GP200, GP215 E032 electronic counter error
CANON GP200, GP215 E051 horizontal registration home position not found
CANON GP200, GP215 E064 High voltage drive board abnormal output
CANON GP200, GP215 E100 BD error
CANON GP200, GP215 E110 polygonal mirror motor not picking up speed
CANON GP200, GP215 E190 RAM error
CANON GP200, GP215 E191 communicatio lost between the main board and the power supply
CANON GP200, GP215 E202 scanner home position not found
CANON GP200, GP215 E203 scanner home position not found
CANON GP200, GP215 E204 scanner home position not found
CANON GP200, GP215 E210 lens home position not found
CANON GP200, GP215 E212 lens home position not found
CANON GP200, GP215 E220 exposure lamp blown or bad contact
CANON GP200, GP215 E240 main board
CANON GP200, GP215 E243 Operation panel
CANON GP200, GP215 E261 Main power supply or Main PCB
CANON GP200, GP215 E301 exposure intensity out of range
CANON GP200, GP215 E400 ADF control board problem
CANON GP200, GP215 E401 DF paper feed motor lock
CANON GP200, GP215 E402 DF transport error
CANON GP200, GP215 E403 DF paper transport error
CANON GP200, GP215 E404 DF paper exit
CANON GP200, GP215 E411 DF sensors problem
CANON GP200, GP215 E422 copier to DF-F1 communication lost
CANON GP200, GP215 E710 main board
CANON GP200, GP215 E711 main board
CANON GP200, GP215 E712 paper feed error
CANON GP200, GP215 E716 Paper feed unit error
CANON GP200, GP215 E717 communication to the copier controller is lost
CANON GP200, GP215 E800 Auto shut-off relay malfunction
CANON GP200, GP215 E803 power supply output out of range
CANON GP200, GP215 E901 Paper feed unit PCB malfunction

Canon i80 Waste Ink Tank Full

2009-12-25T19:08:00.000-08:00

Try this to reset the error.

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6) Power off then back on and test.

Ink Absorber Is Full Canon IP 1880

2009-12-25T08:56:00.000-08:00

BLINKING 2
Out of Paper or Paper feed error
BLINKING 3
Paper Jam
BLINKING 4
Tinta cartridge was out
BLINKI NG 5
Cartridge unknown
BLINKI NG 7
Posisi Cartridge isnot right
BLINGKING 8
Ink absorber full
BLINKING 14
Cartridge unknown

1.) Download ip tool (software for reset waste ink tank)
2.) Unplug the printer power cable. Then hold the power button, while the power cable plug into an electric current, press the resume button once (the power button is pressed ) emerging power button, until this process will be a normal printer, it can be used for printing,
Note:
1. Generator tool can use after printer doesnot blinking / green led
2. Choose usb port,
3. Don’t forget to click Lock Release button then Set Destination pilih 1800 (ASA)
4. Check Cleaning and EPROM Clear
5. Take a paper, click test pattern 1, usually at this process printer back blinking orange
and then in a moment back normally (green led)
6. The end step click Klik tombol Main and Pattern button.
7. To make sure printer is ok, click EPROM information , see the CLTime. characteristic of the printer must be reset, the date on CL Time shows the current date.If it has reset the date has changed.

The second way to reset the IP1980 and the like, pull your printer cartridge and replace it with a still normal cartride thus the printer will recognize the new cartridge.

The third way of using software IPTools
iP Tool is a for Canon resetter iPxxxx type.

Error code Canon IP1300, IP1700, IP1200, IP1880, IP1980

3x orange 1x green = mechanic error

4x orange 1x green = absorber full /reset with general tools

5x orange 1x green= cartirdge black/colour has problem

7x orange 1x green = cartirdge black/colour has problem

8x orange 1xgreen = absorber full / reset with general tools

12x / 15x orange 1x green = cartridge detection

PRINTER CANON iP1980 ABSORBER FULL

2009-12-12T08:25:00.000-08:00

The methods how to "ABSORBER FULL" PRINTER CANON iP1980

Sometimes when the printer is reset but the printer still blingking too. That caused absorber is full, so even though the printer is reset still blingking. The solution I have printer and dismantle the cleaning of the absorber thus more ready to use. Printer All brand ink jet printer provides a special bath containing the ink-absorbing foam. Located at the base of the printer canon.

Following washing steps absorber foam printer canon Pixma IP 1980:
1. Open the printer casing carefully,
a. First you open the casing using a small screwdriver and the right side of the left side of the printer,
b. then proceed to open the upper casing body printer, you first open the front bolts and then just opened the back. See this picture:
C. Well this is rather complicated, you stay open one by one bebrapa bolts attached to the body and hook the printer. Kalo afraid you forgot to pair a special mark (arrow) on certain parts. Remember the clamps really is important when you reinstall the printer casing.
2. Lift the lid and remove the foam absorber absorber of the bath container.
3. Enter cork absorber in the tub / plastic bucket containing water. Preferably warm water. To avoid that your hands are not too dirty to use plastic gloves. Wash and squeeze the cork to ensure a clean cork from the ink.
4. Cork drying absorbers that have been washed in the sun to dry, if you feel anxious to put the printer, why do not yet dry cork put back in place. Make sure the drain hose is correctly pointing to the foam absorber.
5. Before you reinstall the printer casing, it's good you remove the exhaust hose from the printer and you provide a special place for the disposal of these inks. Now the printer in a fresh condition to absorb more ink. Ink absorber risk to other parts of the printer can be avoided and more printers are ready to print.
If still blinking reset the printer.

Canon IR5000, Canon IR6000

2009-12-05T10:39:00.000-08:00

50 A4 ppm. Digital System Solution that seamlessly integrates across networks. Multi-tasking Copier, Printer, and Scanner.
Features of the Canon IR5000 Photocopier
* 50 ppm output
* Mailboxes - 100 available
* Scan Once Print Many
* Mixed Original Copying
* Job Build
* Reserve Jobs
* Job Notification
* 5.1 GB Hard Disk
* Remote User Interface
Further Information
Advanced architecture
Utilizing expert embedded controller technology, the Canon IR5000 photocopier is designed from the ground up to operate as a truly multi-functional unit -without single concept restraints. Thus the system is simpler to connect, monitor and control, while overall productivity and flexibility are also enhanced.
High quality, high speed
The Canon IR5000 photocopier delivers high image quality, high speed output for departmental printing and copying. This multifunctional role eliminates the need for dedicated machines, reducing investment outlay. It also offers greater flexibility for printing on different paper sizes, complete with finishing.
Superior image quality
The Canon IR5000 photocopier offers 50ppm output speed with 256-level grayscale support. Taking image quality to the next level, it incorporates innovative image enhancement technologies to deliver an amazing interpolated printing resolution of 2400 x 600 dpi.
Personal Image Server
It is possible to scan and store existing, hard copy documents onto the iR hard disk, using the Personal Image Server. These scanned documents are stored in a personal mailbox and can then be merged with documents processed on a PC. Thus creating a completely new document from two different sources.
Improved reliability
Reliability is a key element of the Canon IR5000 photocopier, ensuring consistent and continuous output. This next generation digital system is based on Canon extensive experience and proven expertise in digital and imaging technology. Complete with the back up of Canon renowned service coverage.
Full, flexible finishing
When the Canon IR5000 photocopier is configured only with an output tray, the image memory allows convenient electronic collation, with cross collated sets. A Finisher F1 is available offering a high output capacity of 2,000 sheets -in sorted, grouped or stapled mode. Up to 50 sheets can be stapled in a single set.
The Canon iR5000 brochure contains
* iR5000 performance information
* iR5000 optional extras
* iR5000 specifications
Driver iR 5000/ 6000 series Download
service support tool Download iR 5000/ 6000 series
Download Repair system HDD iR 5000/ 6000 series

Epson R1800, R800, R2400 Waste Ink System

2009-12-05T09:12:00.000-08:00

R1900, R1800, R2400, easyrefill cartridges for Epson printer

here is the ADJustment program for epson R800,R1800
please Download the ADj
any other....

Software Resetter Epson Stylus T60

2009-12-05T08:10:00.000-08:00

download Resetter Epson TX100 & T105
download Resetter Epson T50
download Resetter Epson T60
download Resetter Epson R290
download Resetter Epson T11
download Resetter Epson T30

Service Manual for Epson Printers:

Service manual for Epson Stylus Photo 1390Download
Service manual for Epson DFX 8500 Download
Service manual for Epson Stylus Photo 890 Download
Service manual for Epson Stylus Photo 1280 Download
Service manual for Epson Stylus Pro 7600 download
Service manual for Epson Stylus Pro 9600 download

Service Manual for Canon Printers:

Service manual for canon Pixma iP3000 Download
Service manual for canon Pixma iP3300 Download
Service manual for canon Pixma iP4200 Download
Service manual for canon Pixma iP5200 Download
Service manual for canon Pixma iP1500 Download
Service manual for canon Pixma iP5200R Download

Resetter Canon MX318 Printer

2009-12-01T00:43:00.000-08:00

Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.

**********
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
**********

After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
------------------------------------------------

I have tried the above steps, all steps were perform correctly; BUT I am still not able to reset the "color Ink low" message. Please HELP.

Downloaded Resetting Epson Stylus T10 – T11

2009-08-28T19:57:00.000-07:00

These are step by step to reset Waste Ink Counter Pad Epson T11:

1.Download Software Resetter Printer Epson Stylus T11.
2. Ekstract resetter Epson T11.
3. Turn on Printer.
4. Do file AdjProg.exe and klik Accept.
5. Choose Particular adjustment mode.
6. Continue by choose Waste Ink pad Counter and then click OK.
7. Click Check button, to read Waste Ink Counter Pad, and wait till read process finish.
8. Click Initialization to reset waste ink counter pad to 0 and click Finish.
9. Turn off printer, wait a moment, then turn on printer.
10. Wait till printer calibration process finish, and printer be normally.
11. Continue with Test Page Printer.

Before use Software Resetter Epson Stylus T11, Download Resetter

Canon MP and IP paper jam

2009-08-28T09:39:00.000-07:00

Printer doesn’t take paper :
1.Open your printer.
2.At the mechanic part printer (usually a set,
the located below roller and paper tray) there is wheel with pegas.
3.Usually the wheels is not on (hold by long iron like needle).
4.If the wheels are off, you just put back.
5.But when the spring (in the) wheels is corrupt,
structure is usually a mess,is not round at all.
6.You can cut the spring a maximum of 50% of the existing spring.
7.This spring functioning to set the direction of rotation only.
If the spring is too little, then the round will occur in both directions,
if the two directions can not be used.
8.If you can not cut forced find kanibalan from another printer.

Canon MP and IP series rather interesting all the papers
As roller penarik kertas. This is the cheap way
1.Pack up your printer cover (up to how to do, which is important not destroyed)
2.Usually broken the top, near the paper tray, you will find roller drawer paper.
3.Watch as these roller, must be broken.

4.first offthe roller, so u can do it.
5.At fault as the former, make a hole inside approximately 5 mm
by using a drill the smallest, or if you have a drill ga may also
use sharp metal.
6.Find the screw about the size of .
7.Place the screws are in the hole that was made,
then break the screw head with pliers cut,
so you can go into the holder as.
8.Before you install, make sure the fault is found so as not
entered into the printer.
9. If you're satisfied, raft back your printer, and print test your printer.

Resetter canon 1980, 1880, iP2500, iP1900, iP1100, iP1800

2009-08-22T00:40:00.000-07:00

Error printer Always appear message:
“The Ink Absorber is Full
Contact The service Center”.

Or Ink Full Tank usually indicator lamp on power and resume blinking many times

But don’t be afraid, You just follow this step :

Manual Reset Steps :

Press and hold power button with your finger and then take in power cable
Hold power button, then press resume button with your middle finger twice.
Let in power button
Printer doesnot blinking any more.
At this step you had done Manual Reset Step and printer could be use again.
But if manually your printer still error, you should use Reset Software permanently

Do this steps to get your printer permanently :

Download software tool
Extract file ZIP.
Do GeneralTool.exe
At USB Port choose your Port printer.
Click Lock Release button
Choose (check) EEPROM CLEAR
Take blank paper to print. Then click Test Pattern 1 button
Finish and your Printer will be normally

The methodes : here

Canon mpc190 Error code ##335

2009-08-20T06:58:00.000-07:00

Canon MPC190 Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu Copy Scan Copy Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)
and then press the [ON/OFF]

Resetter Canon IP 3300 inkjet Printer

2009-08-09T09:00:00.000-07:00

Try to enter service mode and reset EEPROM:

1. Turn printer OFF
2. Hold down RESUME and then hold down POWER
3. release RESUME
4. press RESUME twice, then release POWER
5. Let green light blink until printer is done moving print head.

Now you should be in service mode.

6. Press RESUME once then POWER to execute
This will print head test print. Just if you want to check clogging problems in depth.

7.Press RESUME twice then POWER to execute
This will print EEPROM information ink usage etc.

8. Press RESUME three times then POWER to execute
This will reinitialize (reset) EEPROM

9. Press RESUME twice then POWER to execute
This will print EEPROM information once more, you should compare it with your fist print. All zeroes should be all over the place.
That means your EEPROM is reset.
Download the complete
user guide

Canon Resetter PIXMA MX868

2009-08-09T08:57:00.000-07:00

Print, Scan, Copy, Fax, Networkable, Wireless, Card Direct

Print
• New ISO/IEC 24734 standard for print speed
• ISO Standard speed (ESAT): approx. 8.4ipm
mono / approx. 5.6ipm colour
•1pl (min) ink droplets and 9600 x 2400 dpi
(max) resolution
• Five-colour individual ink tank system
• 4 x 6” (4R) borderless photo in approx. 41 sec
• Capable of printing borderless photos up to
A4 size
• ChromaLife 100+ technology – photos can last
up to 300 years
• Hybrid system - pigment black ink ensures sharp black text and lines even when printed over
an image

Scan
• 2400 x 4800 dpi CIS
• Auto Scan Mode allows automation of your scanning and saving procedures to three short steps
• Auto duplex scanning with integrated ADF
• Scan directly to flash drive and memory card and save as pdf or jpg

Copy
• New ISO/IEC 24735 Annex D standard for copy speed
• Copy speed (ESAT): approx. 6.8ipm mono / approx. 3.0ipm colour
• Reproduces accurate second generation photos & documents with Dual Colour Gamut
Processing Technology
• Auto duplex copying with integrated ADF
• Binding Margin Copy - binds documents without covering text or images on left side of page
• Punch Hole Removal Copy - eliminates unsightly punch holes from copies
• Print Date/Page Number Copy - prints date and/or page number on each copy
• Gutter Shadow Erase eliminates “gutter” shadows occur in copies made from books
and magazines
• Frame Erase removes the black border that might appear on copies

Fax
• Support Super G3 standard for high-speed electronics transmission
• Security features include fax number re-entry; check RX fax info; caller rejection;
fax reception reject
• ADF faxing up to 35 pages of A4 size
• Store up to 250 faxed pages

SSC SERVICE UTILITY

2009-08-07T08:41:00.000-07:00

SSC Service Utility allow You to do many amazing things with Your Epson printer :

1) Work directly with CSIC in Epson Stylus printers cartridges.
2) Freeze internal ink counters.
3) Reset internal ink counters even with empty cartridges.
4) Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode.
5) Hot swapping of cartridges supported.
6) Resetting of protection counter (even then it is already full).
7) More then 60 different Epson printers supported

This allow many people with high printing demands to save some money (program works with both black and color cartridges).

Up to day this software works under Windows 95/98/ME/2K2/XP with both the LPT and USB printers.

SSC Service Utility v4.30
Latest versions changes:
New in 4.30:
- support for R270
- support for R240
- support for R340
- support for CX2800
- support for CX3900
- support for CX4900
- support for CX5900
- support for C58/C59
- support for RX640
- improved support for C2100/2200
- improved support for RX700
- improved support for R2400
- improved support for 785EPX/825/895/915
- some other improvements and bug fixes

NOTE ! You can lost Epson lifetime guarantee on print head by refilling ink cartridges!
source : http://www.ssclg.com/download/sscserve.exe Download

Reset Waste Ink Printer Canon 'S' Series

2009-08-07T08:28:00.000-07:00

1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. Release the RESUME button, Next press and release the RESUME button
two(2) more times in succession. Note: you are still holding the POWER
button). The printer’s carriage will “reset” or move momentarily. If the above
was properly performed the printer will enter the “Service Mode”.
4. Press the RESUME button 4 times, this will select the clear waste ink counter
function. The lamp will alternate (change) color with each key press.
After selecting the desired mode (eg 4), press the POWER button to “set” the
change, and return to the top of the function selection menu. Press the POWER
button again to restart the printer.

Reset Waste Ink Canon Pixma MP110

Here this step by step to resetting waste ink counter printer Canon Pixma MP110
1. You will include printer.
2. press button Menu, then Scan, Copy and again Scan. All - entered into the service
regime. 3. Select Counter.
3. Press button Copy - all Pampers is discarded into zero.
4. You will turn off printer by button POWER.

Reset Waste Ink Canon Pixma MP450

Here this step by step to resetting waste ink counter printer Canon Pixma MP450
1. You will turn off printer.
2. retaining button Resume/Cancel (red triangle in the circle) press button POWER -
indicator it will catch fire by green color.
3. you will let go button Resume/Cancel, continuing to retain POWER.
4. press button Resume/Cancel of 2 times, retaining POWER, after which you will let
go all buttons.
5. when indicator will be lit BY GREEN - press button Resume/Cancel of 4 times!
6. you will turn off printer by button POWER.

MP390 Waste ink tank full

2009-08-07T08:15:00.000-07:00

To Reset the counter and clear the alarm

1)Printer on, press Additional Functions, Scan, Copy, Scan
Now you should be in service mode from there for waste ink tank reset

2)Select Test mode which is like the last avalabe selection
3)Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

The menu will now say EEPRON Clear
Select Ink count which is option (0) and press set

Then press Stop/Reset Followed by the power button and then wait for it to restart.

As well as:

> Additional functions >Scan >Copy >Scan
> #8 Clear > All > Set
> stop/reset
turn off power

Service manual for BJC 2100SP

2009-08-07T08:08:00.001-07:00

1 Product / Option / Comsumable list
2 Specifications
3 Error code list
4 Service mode
(Test print, EEPROM reset....)
5 External view / Parts list
6 H/W troubleshooting flowchart
Download Link service manual : Click here
Error code 5C00 : S100/S100SP: Download