Tech Support

Certificate Signing Request (CSR) through Microsoft Management Console

karthirk2k7@gmail.com (karthirk2k7) — Mon, 17 Aug 2020 15:49:00 +0000

How to enable e-mail as a two-factor authentication for a user and increase token timeout on FortiGate

karthirk2k7@gmail.com (karthirk2k7) — Wed, 05 Aug 2020 05:36:00 +0000

I would say absolutely that FortiToken (be it a mobile app or a physical token) is the most secure and preferable way today for multi-factor authentication. The other two - SMS message and e-mail message are vulnerable to many attacks, including not so technically sophisticated SMS swapping. But sometimes a less secure method is better than none. Two catches with using an e-mail as MFA on Fortigate though:

It is not available in the GUI until you turn it on at the CLI.

e-mails tend to get delayed sometimes, and the default validity time for any Fortigate produced token code (SMS, e-mail, FortiToken) is 60 seconds. If the user doesn't enter the token code within 60 seconds of issuing - code becomes invalid. It is usually not a problem, but recently I had to enable e-mail MFA for our branch location with substantial e-mail delays being a norm. So optionally below you can find how to increase the default timeout.

Enable e-mail option as MFA for a user:

config user local

edit "karthi"

set type password

set two-factor email

set email-to "karthi@abc.com"

next

end

Now the option for e-mail as 2-factor authentication appears in GUI:

(Optional) Increase token code validity from 1 to 2 minutes:

config system global

(global) # set two-factor-email-expiry ?

two-factor-email-expiry Enter an integer value from <30> to <300> (default = <60>).

(global) # set two-factor-email-expiry 120

Thanks for reading my blog.

How to Disable HTTP Method OPTIONS for the web applications in IIS 7.5 and above

karthirk2k7@gmail.com (karthirk2k7) — Thu, 13 Dec 2018 11:26:00 +0000

ABOUT OPTIONS METHOD

OPTIONS is a diagnostic method which is mainly used for debugging purpose. This HTTP method basically reports which HTTP Methods that are allowed on the web server. In reality, this is rarely used for legitimate purposes, but it does grant a potential attacker a little bit of help and it can be considered a shortcut to find another hole.

How to fix it

OPTIONS method should be disabled.

Way to do it

Methods to disable OPTION method may vary depending upon the type, version of the web server.

Here i am describing IIS Version 7.5 and above.

Open IIS Manager.
Select the name of the machine to configure this globally (or change to the specific web site for which you need to configure this).
Double click on "Request Filtering".
Change to the HTTP Verbs tab.
From the Actions pane, select "Deny Verb".
Insert 'OPTIONS' in the Verb, and press OK to save changes.

Regards

R.Karthikeyan

list of Windows PowerShell commands Useful for administrators

karthirk2k7@gmail.com (karthirk2k7) — Tue, 03 Jul 2018 06:14:00 +0000

Add a DLL to the GAC

1. Run the Power Shell console as Administrator.
2. Enter the following PowerShell

Set-location "c:\Folder Path"            
[System.Reflection.Assembly]::Load("System.EnterpriseServices, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a")            
$publish = New-Object System.EnterpriseServices.Internal.Publish            
$publish.GacInstall("c:\Folder Path\DLL.dll")            
iisreset

Remove a DLL from the GAC

1. Run the PowerShell console as Administrator.
2. Enter the following Power Shell

Set-location "c:\Folder Path"            
[System.Reflection.Assembly]::Load("System.EnterpriseServices, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a")            
$publish = New-Object System.EnterpriseServices.Internal.Publish            
$publish.GacRemove("c:\Folder Path\DLL.dll")            
iisreset

Regards
R Karthikeyan

users temp profile deleting without restart

karthirk2k7@gmail.com (karthirk2k7) — Mon, 26 Mar 2018 06:43:00 +0000

Delete their profile along with the corresponding registry key which can be found in,

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList

In the profile list tree are a list of folders that start with "S-1-5-21-000-2323-" and so on, each one of these folders corresponds to a profile. Click each one, and in the right hand pane you will see something similar to "ProfileImagePath" where the patch shown will show the users logon ID at the very end. Find the folder with that users logon ID and delete it. Have the user now try and logon again which should force a new profile to be built.

MCSA 2016 Prepartion and practice Exam

karthirk2k7@gmail.com (karthirk2k7) — Tue, 10 Oct 2017 08:22:00 +0000

This practice test consists of 15 questions, with correct answers and comments following each submission. They prefer to provide answers and comments after every question so you can see where you’re going wrong and to learn from your mistakes. There’s no point getting to the end of an exam only to realist that 10 out of 20 questions were wrong but with no idea which ones they were.

The test is free and you can retake it as often as you like: on desktop, tablet or mobile. The questions were handwritten and I do not approve of PDF braindumps - you won’t find any copied material here.

Braindumps - It’s worth asking yourself if you’re ok with braindumps. These barely legal documents essentially equate to cheating your way through life. Where’s the self satisfaction or even the challenge in cheating? You’ll get greater pleasure and reward for actually learning the material and passing the exam legitimately. Stick to official training material and do yourself justice in passing the exam yourself - you know you can!

Practice Exam Free

http://www.accelerated-ideas.com/exams/practice-exam.aspx?group=70-740&fq=1&qmax=30

Reference Book:

MCSA 70-740 : http://amzn.to/2g8bhR8

MCSA 70-741 : http://amzn.to/2wKkYbw

MCSA 70-742 : http://amzn.to/2g8CTpi

Regards
R.Karthikeyan

Microsoft Certification Path

karthirk2k7@gmail.com (karthirk2k7) — Thu, 05 Oct 2017 11:57:00 +0000

Hi Friends,

Please find the attached certification path for Microsoft(MCSA & MCSE).

Adding NANO Server to Domain controller 2016

karthirk2k7@gmail.com (karthirk2k7) — Fri, 22 Sep 2017 15:48:00 +0000

Adding NANO Server to Domain controller

After Creating Success Full Nano Server. We need to do some initial configuration to communicate from Domain controller.

We need set IP Address
We need to enable ALL file share and printer sharing session from the inbound firewall rule

Once finished above task. We can move to Domain controller and follow the steps for join nano server to domain.

You will receive file on c:odjblob and you need move same file into your Nano server.

From DC in the file explorer

2. Need to add Nano Server as trusted host on DC

3. You can view the trusted hosts from the below Command

4. You can add Nano server to domain through following command (Offline)

5. To confirm domain join we have to restart the Nano server.

6. We can login through you domain administrator credential.

7. You can see the Domain Column it’s showing my Domain name MYLAB.COM

I just create one html file and pasted into Nano server IIS root folder to confirm my Nano IIS server is working fine. Here we go…..

Regards

R.Karthikeyan

Direct download .bak files through IIS Windows 2012 R2

karthirk2k7@gmail.com (karthirk2k7) — Mon, 11 Sep 2017 07:05:00 +0000

Hi,

Some time for some reason we avoid using FTP Server and we wold like to have alternate for dwolading huge size files.

In My Case almost 20 GB file i need to transfer from one location to another location.
I can use FTP but some of speed restriction policy applied in my FTP server during the peak hours.
we do have alternate ISP in this we are not configure any FTP.

In this i just used IIS Server.(note: Source server I am having public IP access).

I just Followed these three steps and Stared Donwload.

1. Host the test Application.
2. Enable Directory Browsing Give Permisiion to IIS_IUser and IUSR
3. Adding MIME Type.

Add additional MIME types for PKGs:
a. Select Default Web Site in the left sidebar.
b. Double-click MIME Types.
c. Click Add from the right sidebar and type ".bak" in the File name extension field and "application/octet-stream" in the MIME type field. Then, click OK.

Not everything has a custom mime type. For generic binary files

Moving Temp DB to Different Folder / Location

karthirk2k7@gmail.com (karthirk2k7) — Fri, 19 May 2017 08:28:00 +0000

---Determine the logical file names of the tempdb database and their current location on the disk.

SELECT name, physical_name AS CurrentLocation
FROM sys.master_files
WHERE database_id = DB_ID(N'tempdb');
GO

----Change the location of each file by using ALTER DATABASE.

USE master;
GO
ALTER DATABASE tempdb
MODIFY FILE (NAME = tempdev, FILENAME = 'F:\TEMPDB\tempdb.mdf');
GO
ALTER DATABASE tempdb
MODIFY FILE (NAME = templog, FILENAME = 'F:\TEMPLOG\templog.ldf');
GO

--Stop and restart the instance of SQL Server.
--Verify the file change.

SELECT name, physical_name AS CurrentLocation, state_desc
FROM sys.master_files
WHERE database_id = DB_ID(N'tempdb');

--Delete the tempdb.mdf and templog.ldf files from the original location.

How to identify what features has been installed in your SQL Server

karthirk2k7@gmail.com (karthirk2k7) — Thu, 11 May 2017 08:47:00 +0000

How to view the list of features installed in the SQL Server easily without going through “Programs and Features” or “Services”.

Yes, there is an easy way.

Method 1:

we can navigate to the Following Path and see the summary file.

SQL server 2012 Features Installation Discovery.

C:\Program Files\Microsoft SQL Server\110\Setup Bootstrap\Log\Summary.txt

SQL Server 2008 Features Installation Discovery.

C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\Summary.txt

Method 2:

Second method is you can go to the Startup and choose the SQL Server Installation Center.

Select Tools on the Left side and choose Installed SQL Server Features Discovery Report

you will get the Report in internet explorer.

Regards

R.Karthikeyan

Ports for windows file sharing

karthirk2k7@gmail.com (karthirk2k7) — Tue, 02 May 2017 07:48:00 +0000

Sharing a folder or file creates a Windows Firewall exception for File and Printer Sharing. The exception opens the ports listed in the following table.

"If the server has NBT enabled, it listens on UDP ports 137, 138, and on TCP ports 139, 445. If it has NBT disabled, it listens on TCP port 445 only."

Connection	Ports
TCP	139, 445
UDP	137, 138

The default scope is to allow access from any computer on the network, including computers on the Internet. Unless you block incoming connections on these ports using a hardware firewall, firewall server, or other Internet-sharing device, your computer will be vulnerable to attack from the Internet as long as your Internet connection is active.

Regards
கார்த்திகேயன்
Karthikeyan

useful commands-Fortinet Firewall-Part 2

karthirk2k7@gmail.com (karthirk2k7) — Thu, 25 Aug 2016 13:59:00 +0000

Viewing and clearing a DHCP lease is a function you may need to often perform.

The DHCP option is located in different areas of the GUI depending on the firmware version you are running.

The below commands allows you to view and clear a DHCP lease through the CLI.

Commands

exec dhcp lease-list –> show current list on DHCP lease
execute dhcp lease-clear <ip_addres> –> clear the DHCP lease of a specific ip
execute dhcp lease-clear all —> clear all the DHCP leases

Regards

R.Karthikeyan

The database principal owns a schema in the database, and cannot be dropped

karthirk2k7@gmail.com (karthirk2k7) — Thu, 14 Jul 2016 13:40:00 +0000

Last day I had faced issue on SQL Server Login. I was trying to remove the login from database but every single time I was getting error and was not able to remove the user.

How to resolve following error.

The database principal owns a schema in the database, and cannot be dropped. (Microsoft SQL Server, Error: 15138)

I was searching on google and find the solution. Here is the quick workaround to the issue. The reason for error is quite clear from the error message as there were schema associated with the user and that needs to be transferred to another user.

Workaround / Resolution / Fix:

Let us assume that i was trying to delete user which is named as ‘tester’ and it exists in the database ‘Testdb’.

Now run following script with the context of the database where user belongs.

USE Testdb;
SELECT s.name

FROM sys.schemas s

WHERE s.principal_id = USER_ID('tester');

In my query I get following two schema as a result.

two schema name "tqd" and "cls"

Now let us run following query where I will take my schema and and alter authorization on schema. In our case we have two schema so we will execute it two times.

ALTER AUTHORIZATION ON SCHEMA::cls TO dbo;

ALTER AUTHORIZATION ON SCHEMA::tqd TO dbo;

Now if you drop the database owner it will not throw any error.

Here is generic script for resolving the error:

SELECT s.name

FROM sys.schemas s

WHERE s.principal_id = USER_ID('youruserid');

Now replace the result name in following script:

ALTER AUTHORIZATION ON SCHEMA::YourSchemaNa TO dbo;

Thanks to pinal dave for such a good article.

Regards

R.Karthikeyan

Fortigate Firmware upgrade Process On HA

karthirk2k7@gmail.com (karthirk2k7) — Fri, 08 Jul 2016 07:32:00 +0000

Recommend before the upgrade:
1) Check the release notes for supported upgrade path, special notices, product integration, known issues and limitations if any.
2) Backup configuration before and after each upgrade.
3) Plan a maintenance window for the upgrade.
3) Have some one available on the remote site in case something went wrong during the upgrade.
4) Make sure check sum is matching between cluster members using the following CLI commands:
# get sys ha status
# diag sys ha showcsum
# execute ha manage <Slave ID> <<-- could be 0 or 1, check "get sys ha status" results
$ diag sys ha showcsum
$ exit

The results of "diag sys ha showcsum" should be the same on all levels (all/global/vdoms)

Windows Time Service Issue

karthirk2k7@gmail.com (karthirk2k7) — Thu, 07 Jul 2016 11:31:00 +0000

I just wanted to make a statement regarding the time service registry entries. There really is no need to modify the time service registry entries. The time service works by default, out of the box. The only thing that’s recommended to do, is synchronize the PDC Emulator in the forest root domain to a reliable outside source. That’s it.

I’m stating this because based on numerous public postings regarding corrupted time service settings due to attempts at changing registry entries because it was thought that’s how it’s done, is usually the culprit that corrupted the time service settings. The time service should only be configured using the w32tm utility.

If there are any problems with corrupted settings, and it’s not working properly, I would suggest to simply reset the time service itself (stated in the “To Reset the Time service” section below), by simply running the following commands:

If you’ve experimented changing time settings to unknowlingly avert default behavior, you can set the time settings back to default:

1. On the DC that you’re experiencing issues with, run the following in a command prompt:

net stop w32time
w32tm /unregister
w32tm /register
net start w32time

2. On the Server in question (whether it’s the PDC Emulator or another server), run the following in a command prompt:

“net time /setsntp: ” (Note the blank space prior to the end “) [This tells the client (whether a DC or workstation) to delete the current registry settings for time and use default settings.]
Restart the time service: Net stop w32time && net start w32time

3. On the PDC Emulator run the following in a command prompt:

W32tm /config /manualpeerlist:time.nrc.ca /syncfromflags:manual /reliable:yes /update
W32tm /resync /rediscover
Restart the time service: net stop w32time && net start w32time

4. On each DC that are not holding the PDC Emulator role, run the following in a command prompt:

w32tm /config /syncfromflags:domhier /update
W32tm /resync /rediscover
Restart the time service: net stop w32time && net start w32time

5. This will take out any errors in the Event Viewer, if there are any.

.The only real time that you may have to configure it is only with the assistance of Microsoft Support.

Boot from ISO image failed on Generation 2 VM in Hyper V

karthirk2k7@gmail.com (karthirk2k7) — Tue, 28 Jun 2016 07:23:00 +0000

Generation 2 virtual machines in Hyper-V talks booting from CD/DVD. It’s not specific to Hyper-V, it’s more about PCAT and EFI, and the way in which Windows installation media is built.

Try the following – create a new generation 1 and generation 2 VMs with blank VHDXs, setting them both to boot from Windows 8 64-bit .ISO media, and start them.

Here’s what you’ll see in a generation 1 virtual machine (or PCAT physical system)

And here’s what you’ll see in a generation 2 virtual machine (or EFI physical system)

Before anyone comments, yes, Microsoft acutely aware that the generation 2 EFI boot loader messages persist on the screen and it can be a little confusing. Essentially what the generation 2 virtual machine did was:

Attempt to boot from the CD SCSI device containing the Windows 8 ISO. This is where the ‘Press any key…’ message came from. As no key was pressed, we went to the next boot entry. (And this is where we didn’t clear the message from the EFI CD boot loader)
I didn’t press F12 (in fact, this VM wasn’t connected to a network), so network boot failed
The SCSI VHDX is raw with no partitioning or file system, so this too failed

So why did the generation 1 virtual machine start setup from the Windows media? The answer is simply that it’s the way Windows media is built, and it’s inconsistent between the PCAT and EFI loaders.

However, it’s relatively simple to solve if you want to avoid the press any key message. In fact, we almost have all the pieces from previous parts. In particular, part 4 where we injected keyboard drivers into the Windows 8 media.

If you loopback mount Windows 8 or 8.1 RTM media, and navigate to the \efi\microsoft\boot directory, you will see there are two versions of cdboot.efi

The default version, cdboot.efi prompts for a keypress. The unused version, cdboot_noprompt.efi doesn’t prompt.

So it’s fairly simple to create modified media which uses the noprompt version. First, copy the contents of the ISO to a working directory, rename cdboot.efi to cdboot_prompt.efi, and rename cdboot_noprompt.efi to cdboot.efi.

Do the same with efisys.bin and efisys_prompt.bin

Then re-use our oscdimg command (in an elevated deployment and imaging tools environment) from part 4 to recreate the media.

you can download oscdimg from below Link

https://drive.google.com/open?id=0Bz5RYxg0eeodbUxQRW1kVndSTzg
or
http://api.256file.com/download/87465_oscdimg.exe

if you receive ERROR: With -u2, cannot use -n, -nt, -d, -j1, -j2, or -oi

just skip -n

eg:-

d:\Software>oscdimg -o -u2 -udfver102 -bootdata:2#p0,e,b"D:\Software\win2012nop
rompt\boot\etfsboot.com"#pEF,e,b"D:\Software\win2012noprompt\efi\microsoft\boot\
efisys.bin" "D:\Software\win2012noprompt" C:\Working\WIN2012noprompt.iso

Simply attach this modified media to the generation 2 VM and restart it (and don’t press any keys, not that you will be prompted.

Regards

R.Karthikeyan

Find the ErrorLog path in SQL Server 2012 through Query

karthirk2k7@gmail.com (karthirk2k7) — Tue, 17 May 2016 12:21:00 +0000

One other way, that we could get the path of the ErrorLog in SQL Server 2012,when the SQL Server service is running is through this DMV. we can find out the Error Log Path.

SELECT is_enabled,[path],max_size,max_files

FROM

Sys.dm_os_server_diagnostics_log_configurations

Executing this DMV will give valuable information about the ErrorLog like

Path indicating the location of the diagnostic logs.
Maximum size in megabytes to which each of the diagnostic logs can grow.
Maximum number of diagnostic log files that can be stored on the computer before they are recycled for new diagnostic logs.
If logging is enabled or not.

Regards

R.Karthikeyan

How to redirect http to https in IIS

karthirk2k7@gmail.com (karthirk2k7) — Sun, 06 Sep 2015 09:50:00 +0000

1) Download and install the URL Rewrite 2.0 module to your IIS8 server:

Download from here: http://www.iis.net/downloads/microsoft/url-rewrite

2) Once installed, open IIS Manager, expand the Sites container and select the website you wish to configure the http redirection.

3) Once highlighted, double click the URL Rewrite option in the right hand pane. Select Add Rule and configure the following:

NAME

Select: Blank Rule

Name: http to https

Match URL – Requested URL: Matches the Pattern

Match URL – Using: Regular Expression

Pattern: (.*)

CONDITIONS

Conditions: Add

Condition Input: {HTTPS}

Check if input string: Matches the Pattern

Pattern: ^OFF$

Click OK

ACTION

Action type: Redirect

Redirect URL: https://{HTTP_HOST}/{R:1}

Redirect type: See Other (303)

Click Apply

Requests to your site via HTTP should now be redirecting to HTTPS

How to change IPAddress of HP ILO, blades and interconnect modules through OA.

karthirk2k7@gmail.com (karthirk2k7) — Wed, 24 Jun 2015 15:52:00 +0000

Recently I was working on changing HP c7000 enclosure on-board administrator (OA), individual blades and interconnect modules ILO and MSA 1040 Storage Controllers IPs . It’s straight forward but I would like to share my experience here.

Before doing anything further in production/ working environment, take the backup of Virtual Connect (Flexfabric).

Notes:

1. From networking point of view, all IPs are going to be in same subnet. Here in this scenario,

2. Version - OA 4.30
( If you are looking change blade name in HP On-board Administrator, refer to "Steps to change blade in on-board administrator)

Step1: Change OA IP.

• Login to HP OA

• Verify OA fail over to make sure both OA’s are still working after initial implementation ;-). I know our friendly BAU team hardly tests/ patch the environment

• One more point to note, when you are doing OA failover test, it’s not necessarily your active OA IP will go onto passive OA IP based on below setting

• Navigate to enclosure TCP/IP settings

• Change standby on-board administrator ip to new one

• Connect network cable to newly allocated port

• Make sure that able to ping new IP

• Failover OA to standby

• Change active OA IP to new one

• Connect network cable to newly allocated port

• Make sure that able to ping new IP

• Fail back OA to its actual active OA

Step 2: Change individual blade IP

• Login to HP OA.

• Navigate to Enclosure Bay IP Addressing

• Change Device bay IP address to new ones according as allocated

• Make sure that able to ping new IPs

Steps 3: Change interconnect module IP (Virtual/ flex connects)

• Login to HP OA

• Navigate to enclosure TCP/IP settings- Interconnect bays

• Change Device bay 1, 2, 3 and 4 IPs to new as pre allocated.( Note : Device bay depends on how many modules you have)

• Make sure that able to ping new IPs

Update respective DNS alias with new names for all the above devices.

Please share on social media if you found this post helpful. If you have a comment or question, please post and add your voice to the conversation.

Regards

R.Karthikeyan

Get A Free Second Shot on MCP Exams through May 31

karthirk2k7@gmail.com (karthirk2k7) — Thu, 08 Jan 2015 13:20:00 +0000

Welcome to 2015! Have you set your sights on achieving a new Microsoft certification this year? We're here to help.

The very popular "Second Shot" offer is back!

Between January 5 and May 31, 2015, take any Microsoft Certified Professional (MCP) or Microsoft Dynamics exam, and get a free Second Shot if you fail the first take.

With our full transition to Pearson VUE as our sole exam delivery provider this year, there's a slight difference in the Second Shot process. Please note:

You must complete a Microsoft certification exam between January 5, 2015 and May 31, 2015. Simply go to https://www.microsoft.com/learning, log in, and schedule your exam.
After your exam, log in to check your personal dashboard athttps://www.microsoft.com/learning to verify testing results. Please allow up to 24 hours for results to show up on the dashboard.
If you need a Second Shot, select “retake” for your exam within 30 days from your first take.
Please review the Pearson VUE testing center availability for your specifc exam and then schedule your retake.
For complete terms and conditions of this offer, visit the Second Shot page on our website.

Good luck on your road to a new Microsoft certification title.

Migrate RADIUS config from Windows 2003 IAS to Windows 2008 R2 NPS

karthirk2k7@gmail.com (karthirk2k7) — Thu, 20 Nov 2014 10:10:00 +0000

HI,

Recently we were into Migrating the windows Server 2003 based Radius - Internet Authentication Service (IAS) to Windows Server 2008 R2 based Network Policy Server (NPS) task, so I thought to provide the step we were followed.

To perform this migration, perform the following Easy steps:

Step 1:-

Copy IASmigreader.exe from the Windows Server 2008 R2 installation media at \sources\dlmanifests\microsoft-windows-iasserver-migplugin folder to the Windows 2003 server and run as shown below to export the IAS configurations. It will create the configuration file:

Step 2:-

Open the IAS.txt file and find the following text:

=================================================

SystemInfo

=================================================

515

Replace the text with:

=================================================

SystemInfo

=================================================

0000000009

515

Save and import the changed file. This is referenced in http://support.microsoft.com/kb/979599

Step 3:-

Copy the ias.txt file that is generated in the above command and updated as mentioned above to the Windows Server 2008 R2 and import the configuration like so:

At the 2008 R2 Server:

Open NPS console and verify the configurations have been successfully imported.

And now you should register NPS service in Active Directory from the NPS console.

Step 4:-

To register the NPS server in the default domain by using the NPS console:

Log on to the NPS server by using an account that has administrative credentials for the domain.

Open the NPS console.

Right-click NPS (Local) , and then click Register server in Active Directory . When the Register Network

Policy Server in Active Directory dialog box appears, click OK

Regards

R.karthikeyan

Quickly Export and Import DHCP Reservations Windows 2008, Winows 2003

karthirk2k7@gmail.com (karthirk2k7) — Sat, 15 Nov 2014 17:00:00 +0000

    This simple process describes the how to migrate a DHCP reservation list without having to migrate the entire scope.

1.        Export the DHCP reservations, from the Old server which is to be migrated using netsh:

netsh dhcp server [ip address] scope [scope address] dump>c:\temp\reservations.txt

e.g. netsh dhcp server 172.20.2.33 scope 172.16.0.0 dump>c:\temp\reservations.txt

2.        Edit the exported file in notepad 'reservations.txt' , Simply do a Find and Replace for the old DHCP server IP you ran the export on and change to the New DHCP server IP you are importing to and remove out everything else in the text file except for the reservations config section.

3.        On the New DHCP server, make sure you create the new scope first, and ten just simply run the following command DHCP server, make sure from an elevated command prompt in 2008+(Runas Administrator):

   netsh exec C:\temp\reservations.txt

Regards

R.karthikeyan

Get Your 15% MCP Exam Discount Code

karthirk2k7@gmail.com (karthirk2k7) — Tue, 21 Oct 2014 06:39:00 +0000

The last quarter of 2014 is upon us. How's your progress toward your certification goal this year? To help you cross that finish line, we're bringing you a special 15% discount on all MCP exams scheduled and taken by December 31, 2014.

There's no voucher to buy. No extra promotion page to visit. Just use one of these discount codes when you schedule your exam!

Student (academic): STU15OFF
Everyone else: 15OFF

Visit https://www.microsoft.com/learning/exam now to take advantage of this limited time offer. You can choose between Pearson VUE or Prometric testing centers.

Questions? Please review the full terms and conditions below. Good luck on your next exam!

For more information http://borntolearn.mslearn.net/btl/b/weblog/archive/2014/09/25/get-your-15-mcp-exam-discount-code.aspx

Regards

R.karthikeyan

karthirk2k7@gmail.com (karthirk2k7) — Fri, 01 Aug 2014 11:18:00 +0000

Hi

I found this Agile Scrum Process through Graphics while surfing. it would be great to know process.